If extra memory is very much larger than the base memory size
then all of the base memory can be filled with structures reserved to
describe the extra memory, leaving no space for anything else.
Even at the maximum ratio there will be little space for anything else,
but this change is intended to at least allow the system to boot rather
than crash mysteriously.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
If an entire E820 RAM region is beyond mem_end, still add its
pages to the extra area so that space can be used by the kernel.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
If Xen gives us non-RAM E820 entries (dom0 only, typically), then
make sure the extra RAM region is beyond them. It's OK for
the extra space to grow into E820 regions, however.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
When using the e820 map to get the initial pseudo-physical address space,
look for either Xen-provided memory which doesn't lie within an E820
region, or an E820 RAM region which extends beyond the Xen-provided
memory range.
Count these pages, and add them to a new "extra memory" range. This range
has an E820 RAM range to describe it - so the kernel will allocate page
structures for it - but it is also marked reserved so that the kernel
will not attempt to use it.
The balloon driver can then add this range as a set of currently
ballooned-out pages, which can be used to extend the domain beyond its
original size.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Rather than simply using a flat memory map from Xen, use its provided
E820 map. This allows the domain builder to tell the domain to reserve
space for more pages than those initially provided at domain-build time.
It also allows the host to specify holes in the address space (for
PCI-passthrough, for example).
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
When setting up a pte for a missing pfn (no matching mfn), just create
an empty pte rather than a junk mapping.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
When building mfn parts of p2m structure, we rely on being able to
use mfn_to_virt, which in turn requires kernel to be mapped into
the linear area (which is distinct from the kernel image mapping
on 64-bit). Defer calling xen_build_mfn_list_list() until after
xen_setup_kernel_pagetable();
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
set_phys_to_machine() can return false on failure, which means a memory
allocation failure for the p2m structure. It can only fail if setting
the mfn for a pfn in previously unused address space. It is guaranteed
to succeed if you're setting a mapping to INVALID_P2M_ENTRY or updating
the mfn for an existing pfn.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Make the p2m structure a 3 level tree which covers the full possible
physical space.
The p2m structure contains mappings from the domain's pfns to system-wide
mfns. The structure has 3 levels and two roots. The first root is for
the domain's own use, and is linked with virtual addresses. The second
is all mfn references, and is used by Xen on save/restore to allow it to
update the p2m mapping for the domain.
At boot, the domain builder provides a simple flat p2m array for all the
initially present pages. We construct the two levels above that using
the early_brk allocator. After early boot time, set_phys_to_machine()
will allocate any missing levels using the normal kernel allocator
(at GFP_KERNEL, so it must be called in a normal blocking context).
Because the early_brk() API requires us to pre-reserve the maximum amount
of memory we could allocate, there is still a CONFIG_XEN_MAX_DOMAIN_MEMORY
config option, but its only negative side-effect is to increase the
kernel's apparent bss size. However, since all unused brk memory is
returned to the heap, there's no real downside to making it large.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Allocate p2m tables based on the actual runtime maximum pfn rather than
the static config-time limit.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Use early brk mechanism to allocate p2m tables, to save memory when
booting non-Xen.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Commit ab69bcd66f (arm: remove
machine_desc.io_pg_offst and .phys_io) could not update
the new boards in the omap tree. This causes the build of
omap2plus_defconfig to fail. Fix this.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Eric Miao <eric.miao at canonical.com>
[tony@atomide.com: updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic/io.h: allow people to override individual funcs
bitops: remove duplicated extern declarations
bitops: make asm-generic/bitops/find.h more generic
asm-generic: kdebug.h: Checkpatch cleanup
asm-generic: fcntl: make exported headers use strict posix types
asm-generic: cmpxchg does not handle non-long arguments
asm-generic: make atomic_add_unless a function
On OMAP24xx, UART2 WKEN and WKST registers are in PM_WKEN2_CORE and
PM_WKST2_CORE respecitvely. Fix the OMAP2 register init to use the
correct registers on OMAP24xx.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes a warning
warning: (IMX_HAVE_PLATFORM_FLEXCAN && ARCH_MXC) selects HAVE_CAN_FLEXCAN which has unmet direct dependencies (NET && CAN)
(The warning in general exists since
246cf9c (kbuild: Warn on selecting symbols with unmet direct dependencies)
which was reverted between 71ebc01 and b1f7d6e.)
Reported-and-introduced-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'config' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
BKL: introduce CONFIG_BKL.
dabusb: remove the BKL
sunrpc: remove the big kernel lock
init/main.c: remove BKL notations
blktrace: remove the big kernel lock
rtmutex-tester: make it build without BKL
dvb-core: kill the big kernel lock
dvb/bt8xx: kill the big kernel lock
tlclk: remove big kernel lock
fix rawctl compat ioctls breakage on amd64 and itanic
uml: kill big kernel lock
parisc: remove big kernel lock
cris: autoconvert trivial BKL users
alpha: kill big kernel lock
isapnp: BKL removal
s390/block: kill the big kernel lock
hpet: kill BKL, add compat_ioctl
this patch gives the possibility to workaround bug ENGcm09152
on i.MX35 when the hardware workaround is also implemented on
the board.
It covers the workaround described on page 25 of the following Errata :
http://cache.freescale.com/files/dsp/doc/errata/IMX35CE.pdf
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AM35x has musb interface (version 1.8) and uses CPPI41 DMA engine.
It has USB phy built inside the IP itself.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace FSL USB platform code by simple platform driver for
creation of FSL USB platform devices.
The driver creates platform devices based on the information
from USB nodes in the flat device tree. This is the replacement
for old arch fsl_soc usb code removed by this patch. The driver
uses usual of-style binding, available EHCI-HCD and UDC
drivers can be bound to the created devices. The new of-style
driver additionaly instantiates USB OTG platform device, as the
appropriate USB OTG driver will be added soon.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Custom UART PM hook for Alchemy chips: do standard UART pm and
additionally en/disable uart block clocks as needed.
This allows to get rid of a debug port PM hack in the Alchemy pm code.
Tested on Db1200.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Again basically cut and paste
Convert the main driver set to use the hooks for GICOUNT
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts s390 to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- S390 defines its own value for FIOQSIZE, asm-generic/ioctls.h keeps it
- The generic version adds TIOCGRS485 and TIOCGRS485, which are unused
by any driver available on this architecture
- The generic version adds support for termiox
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts mn10300 to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- The generic version provides TIOCGRS485 and TIOCSRS485 but they
are unused by any driver available for this architecture.
- The generic version adds support for termiox
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts m68k to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- m68k defines its own value for FIOQSIZE, asm-generic/ioctls.h keeps it
- The generic version adds TIOCSRS485 and TIOCGRS485m which are unused
by any driver available on this architecture.
- The generic version adds support for termiox
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts m32r to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- The generic version adds TIOCGRS485 and TIOCGRS485, which are unused by
any driver available on this architecture.
- The generic version adds support for termiox
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts ia64 to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- The generic version adds TIOCSRS485 and TIOCGRS485, which are unused
by any driver available on this architecture.
- The generic version adds support for termiox
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts h8300 to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- H8300 defines its own value for FIOQSIZE, asm-generic/ioctls.h keeps it
- The generic version adds TIOCSRS485 and TIOGSRS485, but are unused
by any driver available on this architecture.
- The generic version adds support for termiox
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts frv to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- FRV defines its own value for FIOQSIZE, asm-generic/ioctls.h keeps it
- FRV defines TIOCTTYGSTRUCT, kept in arch-specific version
- The generic version provides TIOCGRS485 and TIOCSRS485 but they
are unused by any driver available for this architecture.
- The generic version adds support for termiox
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts cris to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- CRIS defines two ioctls: TIOCSERSETRS485 and TIOCSERWRRS485,
kept in arch-specific portion
- CRIS defines a different value for TIOCSRS485, kept via ifndef in generic
- The generic version adds support for termiox
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts avr32 to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- The generic version adds support for termiox
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts arm to use asm-generic/ioctls.h instead of its
own version.
The differences between the arch-specific version and the generic
version are as follows:
- ARM defines its own value for FIOQSIZE, asm-generic/ioctls.h keeps it
- The generic version adds support for termiox
Reviewed-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following warning. The function
longrun_cpu_init() is marked with __cpuinit which calls
longrun_get_policy() which is a __init function. So make
longrun_get_policy with __cpuinit.
WARNING: arch/x86/kernel/cpu/cpufreq/longrun.o(.cpuinit.text+0x4c5):
Section mismatch in reference from the function longrun_cpu_init() to
the function .init.text:longrun_get_policy()
The function __cpuinit longrun_cpu_init() references
a function __init longrun_get_policy().
If longrun_get_policy is only used by longrun_cpu_init then
annotate longrun_get_policy with a matching annotation.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>
In each case, the function has an unsigned return type, but returns a
negative constant to indicate an error condition. Each function is only
called once. For nforce2_detect_chipset, the result is only compared to 0,
and for longrun_determine_freqs, the result is stored in a variable of type
(signed) int. Thus, for both functions, unsigned can be dropped from the
return type.
A sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@exists@
identifier f;
constant C;
@@
unsigned f(...)
{ <+...
* return -C;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dave Jones <davej@redhat.com>
For performance reasons its best to use memory node local memory for
per-cpu buffers.
This logic comes from a much larger patch proposed by Stephane.
Suggested-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Stephane Eranian <eranian@google.com>
LKML-Reference: <20101019134808.514465326@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that reserve_ds_buffers() never fails, change it to return
void and remove all code dealing with the error return.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Stephane Eranian <eranian@google.com>
LKML-Reference: <20101019134808.462621937@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently PEBS/BTS buffers are allocated when we instantiate the first
event, when this fails everything fails.
This is a problem because esp. BTS tries to allocate a rather large
buffer (64K), which can easily fail.
This patch changes the logic such that when either buffer allocation
fails, we simply don't allow events that would use these facilities,
but continue functioning for all other events.
This logic comes from a much larger patch proposed by Stephane.
Suggested-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Stephane Eranian <eranian@google.com>
LKML-Reference: <20101019134808.354429461@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In case we don't have PEBS, the LBR fixup doesn't make sense.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Stephane Eranian <eranian@google.com>
LKML-Reference: <20101019134808.354429461@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
