Currently, an "empty" struct pmu is registered as the CPU PMU,
regardless of whether there is a physical PMU. This burdens the
accessor functions with checks to see whether a PMU is actually
present.
This patch changes initialisation to register a PMU only if there is a
supported PMU present, and removes the checks that this change makes
redundant.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Ashwin Chaugule <ashwinc@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently, an event's 'pmu' field is set after pmu::event_init() is
called. This means that pmu::event_init() must figure out which struct
pmu the event was initialised from. This makes it difficult to
consolidate common event initialisation code for similar PMUs, and
very difficult to implement drivers for PMUs which can have multiple
instances (e.g. a USB controller PMU, a GPU PMU, etc).
This patch sets the 'pmu' field before initialising the event, allowing
event init code to identify the struct pmu instance easily. In the
event of failure to initialise an event, the event is destroyed via
kfree() without calling perf_event::destroy(), so this shouldn't
result in bad behaviour even if the destroy field was set before
failure to initialise was noted.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1313062280-19123-1-git-send-email-mark.rutland@arm.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The ARM hw_breakpoint backend is currently a bit too noisy when things
start to go awry.
This patch removes a couple of over-zealous WARN_ONCE invocations and
replaces then with pr_warnings instead.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ARM debug registers can only be accessed if the DBGSWENABLE signal
to the core is driven HIGH by the DAP. The architecture does not provide
a way to detect the value of this signal, so the best we can do is
register an undef_hook to trap debug register co-processor accesses and
then fail if the trap is taken.
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM debug architecture 7.1 mandates that the DFAR is updated on a
watchpoint debug exception to contain the faulting virtual address
of the memory access. This allows us to determine which watchpoints
have fired and therefore report useful information to userspace.
This patch adds support for using the DFAR in the watchpoint handler,
which allows us to support multiple watchpoints on CPUs implementing
the new debug architecture.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The current hw_breakpoint code on ARM reserves 1 breakpoint for each
watchpoint that is available. Since debug architectures prior to 7.1
are restricted to 1 watchpoint anyway, only one breakpoint was ever
reserved.
This patch changes the reservation strategy so that a single breakpoint
is reserved, regardless of the number of watchpoints. This is in
preparation for multiple-watchpoint support on debug architectures
from 7.1 onwards.
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds initial support for Cortex-A15 (debug architecture v7.1)
to the hw_breakpoint ARM backend.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The Cortex-A15 PMU implements the PMUv2 specification and therefore
has support for some mode exclusion.
This patch adds support for excluding user, kernel and hypervisor counts
from a given event.
Acked-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Modern PMUs allow for mode exclusion, so we no longer wish to return
-EPERM if it is requested.
This patch provides a hook in the armpmu structure for implementing
mode exclusion. The hw_perf_event initialisation is slightly delayed so
that the backend code can update the structure if required.
Acked-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM PMU code used to use 1-based indices for PMU registers. This caused
several data structures (pmu_hw_events::{active_events, used_mask, events})
to have an unused element at index zero. ARMPMU_MAX_HWEVENTS still takes
this indexing into account, and currently equates to 33.
This patch updates the core ARM perf code to use the 0th index again.
Acked-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that the ARMv7 PMU backend indexes event counters from zero, follow
suit and do the same for ARMv6 and Xscale.
Acked-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The current ARMv7 PMU backend indexes event counters from two, with
index zero being reserved and index one being used to represent the
cycle counter.
This patch tidies up the code by indexing from one instead (with zero
for the cycle counter). This allows us to remove many of the accessor
macros along with the counter enumeration and makes the code much more
readable.
Acked-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch ensures that integers are used to represent event indices in
the ARMv7 PMU backend. This ensures consistency between functions and
also with the arm_pmu structure.
Acked-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The ARMv7 perf backend mixes up u32 and unsigned long, which is rather
ugly.
This patch makes the ARMv7 PMU code consistently use the u32 type
instead.
Acked-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Commit 5dfc54e0 ("ARM: GIC: avoid routing interrupts to offline CPUs")
prevents the GIC from setting the affinity of an IRQ to a CPU with
id >= nr_cpu_ids. This was previously abused by perf on some platforms
where more IRQs were registered than possible CPUs.
This patch fixes the problem by using a cpumask_t to keep track of the
active (requested) interrupts in perf. The same effect could be achieved
by limiting the number of IRQs to the number of CPUs, but using a mask
instead will be useful for adding extended CPU hotplug support in the
future.
Acked-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Once upon a time, OProfile and Perf fought hard over who could play with
the PMU. To stop all hell from breaking loose, pmu.c offered an internal
reserve/release API and took care of parsing PMU platform data passed in
from board support code.
Now that Perf has ingested OProfile, let's move the platform device
handling into the Perf driver and out of the PMU locking code.
Unfortunately, the lock has to remain to prevent Perf being bitten by
out-of-tree modules such as LTTng, which still claim a right to the PMU
when Perf isn't looking.
Acked-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch removes const qualifiers from instances of struct arm_pmu,
and functions initialising them, in preparation for generalising
arm_pmu usage to system (AKA uncore) PMUs.
This will allow for dynamically modifiable structures (locks,
struct pmu) to be added as members of struct arm_pmu.
Acked-by: Jamie Iles <jamie@jamieiles.com>
Reviewed-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Similarly to PLLs/FLLs some modern CODECs provide selectable system clock
sources. When the clock is the clock for a DAI we do not usually need to
identify which clock is being configured so can use clk_id for the source
clock but with CODEC wide system clocks we will need to specify both the
clock being configured and the source.
Add a source argument to the CODEC driver set_sysclk() operation to
reflect this. As this operation is not as widely used as the DAI
set_sysclk() operation the change is not very invasive. We probably
ought to go and make the same alternation for DAIs at some point.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Devices that need this exist; obviously the newer regmap defaults
mechanism will deal with this more happily.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes the following warning:
CC sound/soc/imx/imx-pcm-fiq.o
sound/soc/imx/imx-pcm-fiq.c: In function 'imx_pcm_fiq_new':
sound/soc/imx/imx-pcm-fiq.c:243: warning: unused variable 'card'
CC sound/soc/imx/imx-pcm-dma-mx2.o
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_codec_readable_register instead of open-coding it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the condition for these WARN_ONs is reversed and they are placed
before the actual check whether we are going to write to that register. So if
the codec implements the register_writable callback we'll get a warning for each
writable register when syncing the register cache.
While we are at it change the check to use snd_soc_codec_writable_register
instead of open-coding it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the default return value of snd_soc_codec_{readable,writable}_register to
true when no codec specific callback for this function is given. Otherwise all
registers of that codec will neither be readable nor writable, which is most
certainly not what we want.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have dapm_context instead of codec parameter.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the channels_min check with a check for the relevant substream
being present. Suggested here [1] when mxs implemented the
audio-support.
[1] http://www.spinics.net/lists/arm-kernel/msg133010.html
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the channel is allocated as writecombine, then mmaping it should also
use writecombine. Also, add a proper device for the call. Ported from a
similar fix for mach-mxs.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
P2P has special rules on when to include P2P IE(s) in Probe Response
frame based on the Probe Request frame. Handle P2P IE(s) separately
to follow these rules.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Edward Lu <elu@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Edward Lu <elu@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Edward Lu <elu@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use WMI_TX_STATUS_EVENTID event to generate cfg80211_mgmt_tx_frame()
calls. Since we support only a single pending frame for now, use the
hardcoded cookie value 1 and store a copy of the pending frame in
the driver.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Edward Lu <elu@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>