[ Upstream commit fe27e709d9 ]
Fedora/CentOS/RHEL CI is reporting intermittent failures while running
the KUnit tests present in drm_hdmi_state_helper_test.c [1].
While the specific test causing the failure change between runs, all of
them are caused by drm_kunit_helper_enable_crtc_connector() returning
-EDEADLK. The error trace always follow this structure:
# <test name>: ASSERTION FAILED at
# drivers/gpu/drm/tests/drm_hdmi_state_helper_test.c:<line>
Expected ret == 0, but
ret == -35 (0xffffffffffffffdd)
As documented, if the drm_kunit_helper_enable_crtc_connector() function
returns -EDEADLK (-35), the entire atomic sequence must be restarted.
Handle this error code for all function calls.
Closes: https://datawarehouse.cki-project.org/issue/4039 [1]
Fixes: 6a5c0ad7e0 ("drm/tests: hdmi_state_helpers: Switch to new helper")
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://patch.msgid.link/20251104102258.10026-1-jose.exposito89@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ef935e659 ]
Currently, the VLAN id may be used without validation when
receive a VLAN configuration mailbox from VF. The length of
vlan_del_fail_bmap is BITS_TO_LONGS(VLAN_N_VID). It may cause
out-of-bounds memory access once the VLAN id is bigger than
or equal to VLAN_N_VID.
Therefore, VLAN id needs to be checked to ensure it is within
the range of VLAN_N_VID.
Fixes: fe4144d47e ("net: hns3: sync VLAN filter entries when kill VLAN ID failed")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251211023737.2327018-4-shaojijie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d180c11aa8 ]
Currently, rss_size = num_tqps / tc_num. If tc_num is 1, then num_tqps
equals rss_size. However, if the tc_num is greater than 1, then rss_size
will be less than num_tqps, causing the tqp_index check for subsequent TCs
using rss_size to always fail.
This patch uses the num_tqps to check whether tqp_index is out of range,
instead of rss_size.
Fixes: 326334aad0 ("net: hns3: add a check for tqp_index in hclge_get_ring_chain_from_mbx()")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251211023737.2327018-3-shaojijie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2a1626974 ]
Currently, hdev->htqp is allocated using hdev->num_tqps, and kinfo->tqp
is allocated using kinfo->num_tqps. However, kinfo->num_tqps is set to
min(new_tqps, hdev->num_tqps); Therefore, kinfo->num_tqps may be smaller
than hdev->num_tqps, which causes some hdev->htqp[i] to remain
uninitialized in hclgevf_knic_setup().
Thus, this patch allocates hdev->htqp and kinfo->tqp using hdev->num_tqps,
ensuring that the lengths of hdev->htqp and kinfo->tqp are consistent
and that all elements are properly initialized.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251211023737.2327018-2-shaojijie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2939203ffe ]
In the current implementation, the enetc_xdp_xmit() always transmits
redirected XDP frames even if the link is down, but the frames cannot
be transmitted from TX BD rings when the link is down, so the frames
are still kept in the TX BD rings. If the XDP program is uninstalled,
users will see the following warning logs.
fsl_enetc 0000:00:00.0 eno0: timeout for tx ring #6 clear
More worse, the TX BD ring cannot work properly anymore, because the
HW PIR and CIR are not equal after the re-initialization of the TX
BD ring. At this point, the BDs between CIR and PIR are invalid,
which will cause a hardware malfunction.
Another reason is that there is internal context in the ring prefetch
logic that will retain the state from the first incarnation of the ring
and continue prefetching from the stale location when we re-initialize
the ring. The internal context is only reset by an FLR. That is to say,
for LS1028A ENETC, software cannot set the HW CIR and PIR when
initializing the TX BD ring.
It does not make sense to transmit redirected XDP frames when the link is
down. Add a link status check to prevent transmission in this condition.
This fixes part of the issue, but more complex cases remain. For example,
the TX BD ring may still contain unsent frames when the link goes down.
Those situations require additional patches, which will build on this
one.
Fixes: 9d2b68cc10 ("net: enetc: add support for XDP_REDIRECT")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251211020919.121113-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15564bd67e ]
When a handshake request is cancelled it is removed from the
handshake_net->hn_requests list, but it is still present in the
handshake_rhashtbl until it is destroyed.
If a second cancellation request arrives for the same handshake request,
then remove_pending() will return false... and assuming
HANDSHAKE_F_REQ_COMPLETED isn't set in req->hr_flags, we'll continue
processing through the out_true label, where we put another reference on
the sock and a refcount underflow occurs.
This can happen for example if a handshake times out - particularly if
the SUNRPC client sends the AUTH_TLS probe to the server but doesn't
follow it up with the ClientHello due to a problem with tlshd. When the
timeout is hit on the server, the server will send a FIN, which triggers
a cancellation request via xs_reset_transport(). When the timeout is
hit on the client, another cancellation request happens via
xs_tls_handshake_sync().
Add a test_and_set_bit(HANDSHAKE_F_REQ_COMPLETED) in the pending cancel
path so duplicate cancels can be detected.
Fixes: 3b3009ea8a ("net/handshake: Create a NETLINK service for handling handshake requests")
Suggested-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Scott Mayhew <smayhew@redhat.com>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Link: https://patch.msgid.link/20251209193015.3032058-1-smayhew@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4198a14c8c ]
Commit [1] added the 40 bytes required by the PSP header+trailer and the
UDP header to MLX5E_ETH_HARD_MTU, which limits the device-wide max
software MTU that could be set. This is not okay, because most packets
are not PSP packets and it doesn't make sense to always reserve space
for headers which won't get added in most cases.
As it turns out, for TCP connections, PSP overhead is already taken into
account in the TCP MSS calculations via inet_csk(sk)->icsk_ext_hdr_len.
This was added in commit [2]. This means that the extra space reserved
in the hard MTU for mlx5 ends up unused and wasted.
Remove the unnecessary 40 byte reservation from hard MTU.
[1] commit e5a1861a29 ("net/mlx5e: Implement PSP Tx data path")
[2] commit e97269257f ("net: psp: update the TCP MSS to reflect PSP
packet overhead")
Fixes: e5a1861a29 ("net/mlx5e: Implement PSP Tx data path")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Shahar Shitrit <shshitrit@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-10-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ab89bde13 ]
When initializing the MAC addresses for an outbound IPsec packet offload
rule in mlx5e_ipsec_init_macs, the call to dst_neigh_lookup is used to
find the next-hop neighbor (typically the gateway in tunnel mode).
This call might create a new neighbor entry if one doesn't already
exist. This newly created entry starts in the INCOMPLETE state, as the
kernel hasn't yet sent an ARP or NDISC probe to resolve the MAC
address. In this case, neigh_ha_snapshot will correctly return an
all-zero MAC address.
IPsec packet offload requires the actual next-hop MAC address to
program the rule correctly. If the neighbor state is INCOMPLETE when
the rule is created, the hardware rule is programmed with an all-zero
destination MAC address. Packets sent using this rule will be
subsequently dropped by the receiving network infrastructure or host.
This patch adds a check specifically for the outbound offload path. If
neigh_ha_snapshot returns an all-zero MAC address, it proactively
calls neigh_event_send(n, NULL). This ensures the kernel immediately
sends the initial ARP or NDISC probe if one isn't already pending,
accelerating the resolution process. This helps prevent the hardware
rule from being programmed with an invalid MAC address and avoids
packet drops due to unresolved neighbors.
Fixes: 71670f766b ("net/mlx5e: Support routed networks during IPsec MACs initialization")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-8-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e35d7da8dd ]
Replace ipv6_stub->ipv6_dst_lookup_flow() with ip6_dst_lookup() in
mlx5e_ipsec_init_macs() since IPsec transformations are not needed
during Security Association setup - only basic routing information is
required for nexthop MAC address resolution.
This resolves an issue where XfrmOutNoStates error counter would be
incremented when xfrm policy is configured before xfrm state, as the
IPsec-aware routing function would attempt policy checks during SA
initialization.
Fixes: 71670f766b ("net/mlx5e: Support routed networks during IPsec MACs initialization")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-7-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 367e501f8b ]
The firmware reset mechanism can be triggered by asynchronous events,
which may race with other devlink operations like devlink reload or
devlink dev eswitch set, potentially leading to inconsistent states.
This patch addresses the race by using the devl_lock to serialize the
firmware reset against other devlink operations. When a reset is
requested, the driver attempts to acquire the lock. If successful, it
sets a flag to block devlink reload or eswitch changes, ACKs the reset
to firmware and then releases the lock. If the lock is already held by
another operation, the driver NACKs the firmware reset request,
indicating that the reset cannot proceed.
Firmware reset does not keep the devl_lock and instead uses an internal
firmware reset bit. This is because firmware resets can be triggered by
asynchronous events, and processed in different threads. It is illegal
and unsafe to acquire a lock in one thread and attempt to release it in
another, as lock ownership is intrinsically thread-specific.
This change ensures that firmware resets and other devlink operations
are mutually exclusive during the critical reset request phase,
preventing race conditions.
Fixes: 38b9f903f2 ("net/mlx5: Handle sync reset request event")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mateusz Berezecki <mberezecki@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-6-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c0289f67f7 ]
The firmware tracer's format string validation and parameter counting
did not properly handle escaped percent signs (%%). This caused
fw_tracer to count more parameters when trace format strings contained
literal percent characters.
To fix it, allow %% to pass string validation and skip %% sequences when
counting parameters since they represent literal percent signs rather
than format specifiers.
Fixes: 70dd6fdb89 ("net/mlx5: FW tracer, parse traces and kernel tracing support")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reported-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Closes: https://lore.kernel.org/netdev/hanz6rzrb2bqbplryjrakvkbmv4y5jlmtthnvi3thg5slqvelp@t3s3erottr6s/
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-5-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b35966042d ]
Add validation for format string parameters in the firmware tracer to
prevent potential security vulnerabilities and crashes from malformed
format strings received from firmware.
The firmware tracer receives format strings from the device firmware and
uses them to format trace messages. Without proper validation, bad
firmware could provide format strings with invalid format specifiers
(e.g., %s, %p, %n) that could lead to crashes, or other undefined
behavior.
Add mlx5_tracer_validate_params() to validate that all format specifiers
in trace strings are limited to safe integer/hex formats (%x, %d, %i,
%u, %llx, %lx, etc.). Reject strings containing other format types that
could be used to access arbitrary memory or cause crashes.
Invalid format strings are added to the trace output for visibility with
"BAD_FORMAT: " prefix.
Fixes: 70dd6fdb89 ("net/mlx5: FW tracer, parse traces and kernel tracing support")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reported-by: Breno Leitao <leitao@debian.org>
Closes: https://lore.kernel.org/netdev/hanz6rzrb2bqbplryjrakvkbmv4y5jlmtthnvi3thg5slqvelp@t3s3erottr6s/
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 89a898d63f ]
drain_fw_reset() waits for ongoing firmware reset events and blocks new
event handling, but does not clear the reset requested flag, and may
keep sync reset polling.
To fix it, call mlx5_sync_reset_clear_reset_requested() to clear the
flag, stop sync reset polling, and resume health polling, ensuring
health issues are still detected after the firmware reset drain.
Fixes: 16d42d3133 ("net/mlx5: Drain fw_reset when removing device")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/1765284977-1363052-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b07be1ff1 ]
The ethtool -S command operates across three ioctl calls:
ETHTOOL_GSSET_INFO for the size, ETHTOOL_GSTRINGS for the names, and
ETHTOOL_GSTATS for the values.
If the number of stats changes between these calls (e.g., due to device
reconfiguration), userspace's buffer allocation will be incorrect,
potentially leading to buffer overflow.
Drivers are generally expected to maintain stable stat counts, but some
drivers (e.g., mlx5, bnx2x, bna, ksz884x) use dynamic counters, making
this scenario possible.
Some drivers try to handle this internally:
- bnad_get_ethtool_stats() returns early in case stats.n_stats is not
equal to the driver's stats count.
- micrel/ksz884x also makes sure not to write anything beyond
stats.n_stats and overflow the buffer.
However, both use stats.n_stats which is already assigned with the value
returned from get_sset_count(), hence won't solve the issue described
here.
Change ethtool_get_strings(), ethtool_get_stats(),
ethtool_get_phy_stats() to not return anything in case of a mismatch
between userspace's size and get_sset_size(), to prevent buffer
overflow.
The returned n_stats value will be equal to zero, to reflect that
nothing has been returned.
This could result in one of two cases when using upstream ethtool,
depending on when the size change is detected:
1. When detected in ethtool_get_strings():
# ethtool -S eth2
no stats available
2. When detected in get stats, all stats will be reported as zero.
Both cases are presumably transient, and a subsequent ethtool call
should succeed.
Other than the overflow avoidance, these two cases are very evident (no
output/cleared stats), which is arguably better than presenting
incorrect/shifted stats.
I also considered returning an error instead of a "silent" response, but
that seems more destructive towards userspace apps.
Notes:
- This patch does not claim to fix the inherent race, it only makes sure
that we do not overflow the userspace buffer, and makes for a more
predictable behavior.
- RTNL lock is held during each ioctl, the race window exists between
the separate ioctl calls when the lock is released.
- Userspace ethtool always fills stats.n_stats, but it is likely that
these stats ioctls are implemented in other userspace applications
which might not fill it. The added code checks that it's not zero,
to prevent any regressions.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20251208121901.3203692-1-gal@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46cea215dc ]
There is a theoretical race window in j1939_sk_netdev_event_unregister()
where two j1939_sk_bind() calls jump in between read_unlock_bh() and
lock_sock().
The assumption jsk->priv == priv can fail if the first j1939_sk_bind()
call once made jsk->priv == NULL due to failed j1939_local_ecu_get() call
and the second j1939_sk_bind() call again made jsk->priv != NULL due to
successful j1939_local_ecu_get() call.
Since the socket lock is held by both j1939_sk_netdev_event_unregister()
and j1939_sk_bind(), checking ndev->reg_state with the socket lock held can
reliably make the second j1939_sk_bind() call fail (and close this race
window).
Fixes: 7fcbe5b2c6 ("can: j1939: implement NETDEV_UNREGISTER notification handler")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/5732921e-247e-4957-a364-da74bd7031d7@I-love.SAKURA.ne.jp
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5b244b077c ]
GCC gets a bit confused and reports:
In function '_test_cmd_get_hw_info',
inlined from 'iommufd_ioas_get_hw_info' at iommufd.c:779:3,
inlined from 'wrapper_iommufd_ioas_get_hw_info' at iommufd.c:752:1:
>> iommufd_utils.h:804:37: warning: array subscript 'struct iommu_test_hw_info[0]' is partly outside array bounds of 'struct iommu_test_hw_info_buffer_smaller[1]' [-Warray-bounds=]
804 | assert(!info->flags);
| ~~~~^~~~~~~
iommufd.c: In function 'wrapper_iommufd_ioas_get_hw_info':
iommufd.c:761:11: note: object 'buffer_smaller' of size 4
761 | } buffer_smaller;
| ^~~~~~~~~~~~~~
While it is true that "struct iommu_test_hw_info[0]" is partly out of
bounds of the input pointer, it is not true that info->flags is out of
bounds. Unclear why it warns on this.
Reuse an existing properly sized stack buffer and pass a truncated length
instead to test the same thing.
Fixes: af4fde93c3 ("iommufd/selftest: Add coverage for IOMMU_GET_HW_INFO ioctl")
Link: https://patch.msgid.link/r/0-v1-63a2cffb09da+4486-iommufd_gcc_bounds_jgg@nvidia.com
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202512032344.kaAcKFIM-lkp@intel.com/
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a67fd55f6a ]
This validation predates the introduction of the state machine that
determines when to enter slow path validation for error reporting.
Currently, table validation is perform when:
- new rule contains expressions that need validation.
- new set element with jump/goto verdict.
Validation on register store skips most checks with no basechains, still
this walks the graph searching for loops and ensuring expressions are
called from the right hook. Remove this.
Fixes: a654de8fdc ("netfilter: nf_tables: fix chain dependency validation")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ec8ca26fe ]
Jakub reports spurious failures of the 'conntrack_reverse_clash.sh'
selftest. A bogus test makes nat core resort to port rewrite even
though there is no need for this.
When the test is made, nf_nat_used_tuple() would already have caused us
to return if no other CPU had added a colliding entry.
Moreover, nf_nat_used_tuple() would have ignored the colliding entry if
their origin tuples had been the same.
All that is left to check is if the colliding entry in the hash table
is subject to NAT, and, if its not, if our entry matches in the reverse
direction, e.g. hash table has
addr1:1234 -> addr2:80, and we want to commit
addr2:80 -> addr1:1234.
Because we already checked that neither the new nor the committed entry is
subject to NAT we only have to check origin vs. reply tuple:
for non-nat entries, the reply tuple is always the inverted original.
Just in case there are more problems extend the error reporting
in the selftest while at it and dump conntrack table/stats on error.
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netdev/20251206175135.4a56591b@kernel.org/
Fixes: d8f84a9bc7 ("netfilter: nf_nat: don't try nat source port reallocation for reverse dir clash")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 885bebac99 ]
Set the error code if "transferred != sizeof(cmd)" instead of
returning success.
Fixes: dbafc28955 ("NFC: pn533: don't send USB data off of the stack")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://patch.msgid.link/aTfIJ9tZPmeUF4W1@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a11ff0948 ]
The cffrml_receive() function extracts a length field from the packet
header and, when FCS is disabled, subtracts 2 from this length without
validating that len >= 2.
If an attacker sends a malicious packet with a length field of 0 or 1
to an interface with FCS disabled, the subtraction causes an integer
underflow.
This can lead to memory exhaustion and kernel instability, potential
information disclosure if padding contains uninitialized kernel memory.
Fix this by validating that len >= 2 before performing the subtraction.
Reported-by: Yuhao Jiang <danisjiang@gmail.com>
Reported-by: Junrui Luo <moonafterrain@outlook.com>
Fixes: b482cd2053 ("net-caif: add CAIF core protocol stack")
Signed-off-by: Junrui Luo <moonafterrain@outlook.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/SYBPR01MB7881511122BAFEA8212A1608AFA6A@SYBPR01MB7881.ausprd01.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8a81b0ce5 ]
Jakub says: "We try to reserve SKIP for tests skipped because tool is
missing in env, something isn't built into the kernel etc."
use xfail, we can't force the race condition to appear at will
so its expected that the test 'fails' occasionally.
Fixes: 78a5883635 ("selftests: netfilter: add conntrack clash resolution test case")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netdev/20251206175647.5c32f419@kernel.org/
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad891bb3d0 ]
The IPv4 code path in __ip_vs_get_out_rt() calls dst_link_failure()
without ensuring skb->dev is set, leading to a NULL pointer dereference
in fib_compute_spec_dst() when ipv4_link_failure() attempts to send
ICMP destination unreachable messages.
The issue emerged after commit ed0de45a10 ("ipv4: recompile ip options
in ipv4_link_failure") started calling __ip_options_compile() from
ipv4_link_failure(). This code path eventually calls fib_compute_spec_dst()
which dereferences skb->dev. An attempt was made to fix the NULL skb->dev
dereference in commit 0113d9c9d1 ("ipv4: fix null-deref in
ipv4_link_failure"), but it only addressed the immediate dev_net(skb->dev)
dereference by using a fallback device. The fix was incomplete because
fib_compute_spec_dst() later in the call chain still accesses skb->dev
directly, which remains NULL when IPVS calls dst_link_failure().
The crash occurs when:
1. IPVS processes a packet in NAT mode with a misconfigured destination
2. Route lookup fails in __ip_vs_get_out_rt() before establishing a route
3. The error path calls dst_link_failure(skb) with skb->dev == NULL
4. ipv4_link_failure() → ipv4_send_dest_unreach() →
__ip_options_compile() → fib_compute_spec_dst()
5. fib_compute_spec_dst() dereferences NULL skb->dev
Apply the same fix used for IPv6 in commit 326bf17ea5 ("ipvs: fix
ipv6 route unreach panic"): set skb->dev from skb_dst(skb)->dev before
calling dst_link_failure().
KASAN: null-ptr-deref in range [0x0000000000000328-0x000000000000032f]
CPU: 1 PID: 12732 Comm: syz.1.3469 Not tainted 6.6.114 #2
RIP: 0010:__in_dev_get_rcu include/linux/inetdevice.h:233
RIP: 0010:fib_compute_spec_dst+0x17a/0x9f0 net/ipv4/fib_frontend.c:285
Call Trace:
<TASK>
spec_dst_fill net/ipv4/ip_options.c:232
spec_dst_fill net/ipv4/ip_options.c:229
__ip_options_compile+0x13a1/0x17d0 net/ipv4/ip_options.c:330
ipv4_send_dest_unreach net/ipv4/route.c:1252
ipv4_link_failure+0x702/0xb80 net/ipv4/route.c:1265
dst_link_failure include/net/dst.h:437
__ip_vs_get_out_rt+0x15fd/0x19e0 net/netfilter/ipvs/ip_vs_xmit.c:412
ip_vs_nat_xmit+0x1d8/0xc80 net/netfilter/ipvs/ip_vs_xmit.c:764
Fixes: ed0de45a10 ("ipv4: recompile ip options in ipv4_link_failure")
Signed-off-by: Slavin Liu <slavin452@gmail.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e2a720766 ]
There are some situations where ct might be leaked as error paths are
skipping the refcounted check and return immediately. In order to solve
it make sure that the check is always called.
Fixes: be102eb6a0 ("netfilter: nf_conncount: rework API to use sk_buff directly")
Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 006a5035b4 ]
We have been seeing occasional deadlocks on pernet_ops_rwsem since
September in NIPA. The stuck task was usually modprobe (often loading
a driver like ipvlan), trying to take the lock as a Writer.
lockdep does not track readers for rwsems so the read wasn't obvious
from the reports.
On closer inspection the Reader holding the lock was conntrack looping
forever in nf_conntrack_cleanup_net_list(). Based on past experience
with occasional NIPA crashes I looked thru the tests which run before
the crash and noticed that the crash follows ip_defrag.sh. An immediate
red flag. Scouring thru (de)fragmentation queues reveals skbs sitting
around, holding conntrack references.
The problem is that since conntrack depends on nf_defrag_ipv6,
nf_defrag_ipv6 will load first. Since nf_defrag_ipv6 loads first its
netns exit hooks run _after_ conntrack's netns exit hook.
Flush all fragment queue SKBs during fqdir_pre_exit() to release
conntrack references before conntrack cleanup runs. Also flush
the queues in timer expiry handlers when they discover fqdir->dead
is set, in case packet sneaks in while we're running the pre_exit
flush.
The commit under Fixes is not exactly the culprit, but I think
previously the timer firing would eventually unblock the spinning
conntrack.
Fixes: d5dd88794a ("inet: fix various use-after-free in defrags units")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20251207010942.1672972-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1231eec699 ]
Instead of exporting inet_frag_rbtree_purge() which requires that
caller takes care of memory accounting, add a new helper. We will
need to call it from a few places in the next patch.
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20251207010942.1672972-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 006a5035b4 ("inet: frags: flush pending skbs in fqdir_pre_exit()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ef522c8a5 ]
In ip_frag_reinit() we want to move the frag timeout timer into
the future. If the timer fires in the meantime we inadvertently
scheduled it again, and since the timer assumes a ref on frag_queue
we need to acquire one to balance things out.
This is technically racy, we should have acquired the reference
_before_ we touch the timer, it may fire again before we take the ref.
Avoid this entire dance by using mod_timer_pending() which only modifies
the timer if its pending (and which exists since Linux v2.6.30)
Note that this was the only place we ever took a ref on frag_queue
since Eric's conversion to RCU. So we could potentially replace
the whole refcnt field with an atomic flag and a bit more RCU.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20251207010942.1672972-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91dc09a609 ]
Fix
tfo.c: In function ‘run_server’:
tfo.c:84:9: warning: ignoring return value of ‘read’ declared with attribute ‘warn_unused_result’
by evaluating the return value from read() and displaying an error message
if it reports an error.
Fixes: c65b5bb232 ("selftests: net: add passive TFO test binary")
Cc: David Wei <dw@davidwei.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://patch.msgid.link/20251205171010.515236-14-linux@roeck-us.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59546e8744 ]
Fix
ksft.h: In function ‘ksft_ready’:
ksft.h:27:9: warning: ignoring return value of ‘write’ declared with attribute ‘warn_unused_result’
ksft.h: In function ‘ksft_wait’:
ksft.h:51:9: warning: ignoring return value of ‘read’ declared with attribute ‘warn_unused_result’
by checking the return value of the affected functions and displaying
an error message if an error is seen.
Fixes: 2b6d490b82 ("selftests: drv-net: Factor out ksft C helpers")
Cc: Joe Damato <jdamato@fastly.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://patch.msgid.link/20251205171010.515236-11-linux@roeck-us.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50b3db3e11 ]
On execution path with raised B44_FLAG_EXTERNAL_PHY, b44_readphy()
leaves bmcr value uninitialized and it is used later in the code.
Add check of this flag at the beginning of the b44_nway_reset() and
exit early of the function with restarting autonegotiation if an
external PHY is used.
Fixes: 753f492093 ("[B44]: port to native ssb support")
Reviewed-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexey Simakov <bigalex934@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20251205155815.4348-1-bigalex934@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e7477a427 ]
The new icssg-prueth driver needs the same dependency as the other parts
that use the ptp-1588:
WARNING: unmet direct dependencies detected for TI_ICSS_IEP
Depends on [m]: NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && PTP_1588_CLOCK_OPTIONAL [=m] && TI_PRUSS [=y]
Selected by [y]:
- TI_PRUETH [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && PRU_REMOTEPROC [=y] && NET_SWITCHDEV [=y]
Add the correct dependency on the two drivers missing it, and remove
the pointless 'imply' in the process.
Fixes: e654b85a69 ("net: ti: icssg-prueth: Add ICSSG Ethernet driver for AM65x SR1.0 platforms")
Fixes: 511f6c1ae0 ("net: ti: icssm-prueth: Adds ICSSM Ethernet driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20251204100138.1034175-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ace7ef87f ]
The push_nsh() action structure looks like this:
OVS_ACTION_ATTR_PUSH_NSH(OVS_KEY_ATTR_NSH(OVS_NSH_KEY_ATTR_BASE,...))
The outermost OVS_ACTION_ATTR_PUSH_NSH attribute is OK'ed by the
nla_for_each_nested() inside __ovs_nla_copy_actions(). The innermost
OVS_NSH_KEY_ATTR_BASE/MD1/MD2 are OK'ed by the nla_for_each_nested()
inside nsh_key_put_from_nlattr(). But nothing checks if the attribute
in the middle is OK. We don't even check that this attribute is the
OVS_KEY_ATTR_NSH. We just do a double unwrap with a pair of nla_data()
calls - first time directly while calling validate_push_nsh() and the
second time as part of the nla_for_each_nested() macro, which isn't
safe, potentially causing invalid memory access if the size of this
attribute is incorrect. The failure may not be noticed during
validation due to larger netlink buffer, but cause trouble later during
action execution where the buffer is allocated exactly to the size:
BUG: KASAN: slab-out-of-bounds in nsh_hdr_from_nlattr+0x1dd/0x6a0 [openvswitch]
Read of size 184 at addr ffff88816459a634 by task a.out/22624
CPU: 8 UID: 0 PID: 22624 6.18.0-rc7+ #115 PREEMPT(voluntary)
Call Trace:
<TASK>
dump_stack_lvl+0x51/0x70
print_address_description.constprop.0+0x2c/0x390
kasan_report+0xdd/0x110
kasan_check_range+0x35/0x1b0
__asan_memcpy+0x20/0x60
nsh_hdr_from_nlattr+0x1dd/0x6a0 [openvswitch]
push_nsh+0x82/0x120 [openvswitch]
do_execute_actions+0x1405/0x2840 [openvswitch]
ovs_execute_actions+0xd5/0x3b0 [openvswitch]
ovs_packet_cmd_execute+0x949/0xdb0 [openvswitch]
genl_family_rcv_msg_doit+0x1d6/0x2b0
genl_family_rcv_msg+0x336/0x580
genl_rcv_msg+0x9f/0x130
netlink_rcv_skb+0x11f/0x370
genl_rcv+0x24/0x40
netlink_unicast+0x73e/0xaa0
netlink_sendmsg+0x744/0xbf0
__sys_sendto+0x3d6/0x450
do_syscall_64+0x79/0x2c0
entry_SYSCALL_64_after_hwframe+0x76/0x7e
</TASK>
Let's add some checks that the attribute is properly sized and it's
the only one attribute inside the action. Technically, there is no
real reason for OVS_KEY_ATTR_NSH to be there, as we know that we're
pushing an NSH header already, it just creates extra nesting, but
that's how uAPI works today. So, keeping as it is.
Fixes: b2d0f5d5dc ("openvswitch: enable NSH support")
Reported-by: Junvy Yang <zhuque@tencent.com>
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Eelco Chaudron echaudro@redhat.com
Reviewed-by: Aaron Conole <aconole@redhat.com>
Link: https://patch.msgid.link/20251204105334.900379-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0373d5c387 ]
For XDP_TX action in bnxt_rx_xdp(), clearing of the event flags is not
correct. __bnxt_poll_work() -> bnxt_rx_pkt() -> bnxt_rx_xdp() may be
looping within NAPI and some event flags may be set in earlier
iterations. In particular, if BNXT_TX_EVENT is set earlier indicating
some XDP_TX packets are ready and pending, it will be cleared if it is
XDP_TX action again. Normally, we will set BNXT_TX_EVENT again when we
successfully call __bnxt_xmit_xdp(). But if the TX ring has no more
room, the flag will not be set. This will cause the TX producer to be
ahead but the driver will not hit the TX doorbell.
For multi-buf XDP_TX, there is no need to clear the event flags and set
BNXT_AGG_EVENT. The BNXT_AGG_EVENT flag should have been set earlier in
bnxt_rx_pkt().
The visible symptom of this is that the RX ring associated with the
TX XDP ring will eventually become empty and all packets will be dropped.
Because this condition will cause the driver to not refill the RX ring
seeing that the TX ring has forever pending XDP_TX packets.
The fix is to only clear BNXT_RX_EVENT when we have successfully
called __bnxt_xmit_xdp().
Fixes: 7f0a168b04 ("bnxt_en: Add completion ring pointer in TX and RX ring structures")
Reported-by: Pavel Dubovitsky <pdubovitsky@meta.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20251203003024.2246699-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ac1dacec4 ]
Cited commit added a dedicated mutex (instead of RTNL) to protect the
multicast route list, so that it will not change while the driver
periodically traverses it in order to update the kernel about multicast
route stats that were queried from the device.
One instance of list entry deletion (during route replace) was missed
and it can result in a use-after-free [1].
Fix by acquiring the mutex before deleting the entry from the list and
releasing it afterwards.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_mr_stats_update+0x4a5/0x540 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:1006 [mlxsw_spectrum]
Read of size 8 at addr ffff8881523c2fa8 by task kworker/2:5/22043
CPU: 2 UID: 0 PID: 22043 Comm: kworker/2:5 Not tainted 6.18.0-rc1-custom-g1a3d6d7cd014 #1 PREEMPT(full)
Hardware name: Mellanox Technologies Ltd. MSN2010/SA002610, BIOS 5.6.5 08/24/2017
Workqueue: mlxsw_core mlxsw_sp_mr_stats_update [mlxsw_spectrum]
Call Trace:
<TASK>
dump_stack_lvl+0xba/0x110
print_report+0x174/0x4f5
kasan_report+0xdf/0x110
mlxsw_sp_mr_stats_update+0x4a5/0x540 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:1006 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30
</TASK>
Allocated by task 29933:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
mlxsw_sp_mr_route_add+0xd8/0x4770 [mlxsw_spectrum]
mlxsw_sp_router_fibmr_event_work+0x371/0xad0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7965 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30
Freed by task 29933:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_save_free_info+0x3b/0x70
__kasan_slab_free+0x43/0x70
kfree+0x14e/0x700
mlxsw_sp_mr_route_add+0x2dea/0x4770 drivers/net/ethernet/mellanox/mlxsw/spectrum_mr.c:444 [mlxsw_spectrum]
mlxsw_sp_router_fibmr_event_work+0x371/0xad0 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:7965 [mlxsw_spectrum]
process_one_work+0x9cc/0x18e0
worker_thread+0x5df/0xe40
kthread+0x3b8/0x730
ret_from_fork+0x3e9/0x560
ret_from_fork_asm+0x1a/0x30
Fixes: f38656d067 ("mlxsw: spectrum_mr: Protect multicast route list with a lock")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/f996feecfd59fde297964bfc85040b6d83ec6089.1764695650.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8b0e69763e ]
We sometimes observe use-after-free when dereferencing a neighbour [1].
The problem seems to be that the driver stores a pointer to the
neighbour, but without holding a reference on it. A reference is only
taken when the neighbour is used by a nexthop.
Fix by simplifying the reference counting scheme. Always take a
reference when storing a neighbour pointer in a neighbour entry. Avoid
taking a referencing when the neighbour is used by a nexthop as the
neighbour entry associated with the nexthop already holds a reference.
Tested by running the test that uncovered the problem over 300 times.
Without this patch the problem was reproduced after a handful of
iterations.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_neigh_entry_update+0x2d4/0x310
Read of size 8 at addr ffff88817f8e3420 by task ip/3929
CPU: 3 UID: 0 PID: 3929 Comm: ip Not tainted 6.18.0-rc4-virtme-g36b21a067510 #3 PREEMPT(full)
Hardware name: Nvidia SN5600/VMOD0013, BIOS 5.13 05/31/2023
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xa0
print_address_description.constprop.0+0x6e/0x300
print_report+0xfc/0x1fb
kasan_report+0xe4/0x110
mlxsw_sp_neigh_entry_update+0x2d4/0x310
mlxsw_sp_router_rif_gone_sync+0x35f/0x510
mlxsw_sp_rif_destroy+0x1ea/0x730
mlxsw_sp_inetaddr_port_vlan_event+0xa1/0x1b0
__mlxsw_sp_inetaddr_lag_event+0xcc/0x130
__mlxsw_sp_inetaddr_event+0xf5/0x3c0
mlxsw_sp_router_netdevice_event+0x1015/0x1580
notifier_call_chain+0xcc/0x150
call_netdevice_notifiers_info+0x7e/0x100
__netdev_upper_dev_unlink+0x10b/0x210
netdev_upper_dev_unlink+0x79/0xa0
vrf_del_slave+0x18/0x50
do_set_master+0x146/0x7d0
do_setlink.isra.0+0x9a0/0x2880
rtnl_newlink+0x637/0xb20
rtnetlink_rcv_msg+0x6fe/0xb90
netlink_rcv_skb+0x123/0x380
netlink_unicast+0x4a3/0x770
netlink_sendmsg+0x75b/0xc90
__sock_sendmsg+0xbe/0x160
____sys_sendmsg+0x5b2/0x7d0
___sys_sendmsg+0xfd/0x180
__sys_sendmsg+0x124/0x1c0
do_syscall_64+0xbb/0xfd0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
[...]
Allocated by task 109:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x7b/0x90
__kmalloc_noprof+0x2c1/0x790
neigh_alloc+0x6af/0x8f0
___neigh_create+0x63/0xe90
mlxsw_sp_nexthop_neigh_init+0x430/0x7e0
mlxsw_sp_nexthop_type_init+0x212/0x960
mlxsw_sp_nexthop6_group_info_init.constprop.0+0x81f/0x1280
mlxsw_sp_nexthop6_group_get+0x392/0x6a0
mlxsw_sp_fib6_entry_create+0x46a/0xfd0
mlxsw_sp_router_fib6_replace+0x1ed/0x5f0
mlxsw_sp_router_fib6_event_work+0x10a/0x2a0
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20
Freed by task 154:
kasan_save_stack+0x30/0x50
kasan_save_track+0x14/0x30
__kasan_save_free_info+0x3b/0x60
__kasan_slab_free+0x43/0x70
kmem_cache_free_bulk.part.0+0x1eb/0x5e0
kvfree_rcu_bulk+0x1f2/0x260
kfree_rcu_work+0x130/0x1b0
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20
Last potentially related work creation:
kasan_save_stack+0x30/0x50
kasan_record_aux_stack+0x8c/0xa0
kvfree_call_rcu+0x93/0x5b0
mlxsw_sp_router_neigh_event_work+0x67d/0x860
process_one_work+0xd57/0x1390
worker_thread+0x4d6/0xd40
kthread+0x355/0x5b0
ret_from_fork+0x1d4/0x270
ret_from_fork_asm+0x11/0x20
Fixes: 6cf3c971dc ("mlxsw: spectrum_router: Add private neigh table")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/92d75e21d95d163a41b5cea67a15cd33f547cba6.1764695650.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6b638bda2 ]
mlxsw_sp_router_schedule_work() takes a reference on a neighbour,
expecting a work item to release it later on. However, we might fail to
schedule the work item, in which case the neighbour reference count will
be leaked.
Fix by taking the reference just before scheduling the work item. Note
that mlxsw_sp_router_schedule_work() can receive a NULL neighbour
pointer, but neigh_clone() handles that correctly.
Spotted during code review, did not actually observe the reference count
leak.
Fixes: 151b89f602 ("mlxsw: spectrum_router: Reuse work neighbor initialization in work scheduler")
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/ec2934ae4aca187a8d8c9329a08ce93cca411378.1764695650.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c57ff008a ]
Packets with pkt_type == PACKET_LOOPBACK are captured by
handle_frame() function, but they don't have L2 header.
We should not process them in handle_mode_l2().
This doesn't affect old L2 functionality, since handling
was anyway incorrect.
Handle them the same way as in br_handle_frame():
just pass the skb.
To observe invalid behaviour, just start "ping -b" on bcast address
of port-interface.
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Dmitry Skorodumov <skorodumov.dmitry@huawei.com>
Link: https://patch.msgid.link/20251202103906.4087675-1-skorodumov.dmitry@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f0638b124 ]
When support for RTL8211F(D)(I)-VD-CG was introduced in commit
bb726b753f ("net: phy: realtek: add support for RTL8211F(D)(I)-VD-CG")
the implementation assumed that this PHY model doesn't have the
control register PHYCR2 (Page 0xa43 Address 0x19). This
assumption was based on the differences in CLKOUT configurations
between RTL8211FVD and the remaining RTL8211F PHYs. In the latter
commit 2c67301584
("net: phy: realtek: Avoid PHYCR2 access if PHYCR2 not present")
this assumption was expanded to the PHY-mode EEE.
I performed tests on RTL8211FI-VD-CG and confirmed that disabling
PHY-mode EEE works correctly and is uniform with other PHYs
supported by the driver. To validate the correctness,
I contacted Realtek support. Realtek confirmed that PHY-mode EEE on
RTL8211F(D)(I)-VD-CG is configured via Page 0xa43 Address 0x19 bit 5.
Moreover, Realtek informed me that the most recent datasheet
for RTL8211F(D)(I)-VD-CG v1.1 is incomplete and the naming of
control registers is partly inconsistent. The errata I
received from Realtek corrects the naming as follows:
| Register | Datasheet v1.1 | Errata |
|-------------------------|----------------|--------|
| Page 0xa44 Address 0x11 | PHYCR2 | PHYCR3 |
| Page 0xa43 Address 0x19 | N/A | PHYCR2 |
This information confirms that the supposedly missing control register,
PHYCR2, exists in the RTL8211F(D)(I)-VD-CG under the same address and
the same name. It controls widely the same configs as other PHYs from
the RTL8211F series (e.g. PHY-mode EEE). Clock out configuration is an
exception.
Given all this information, restore disabling of the PHY-mode EEE.
Fixes: 2c67301584 ("net: phy: realtek: Avoid PHYCR2 access if PHYCR2 not present")
Signed-off-by: Ivan Galkin <ivan.galkin@axis.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251202-phy_eee-v1-1-fe0bf6ab3df0@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4465ae435d ]
To simplify the rtl8211f_config_init() control flow and get rid of
"early" returns for PHYs where the PHYCR2 register is absent, move the
entire logic sub-block that deals with disabling PHY-mode EEE to a
separate function. There, it is much more obvious what the early
"return 0" skips, and it becomes more difficult to accidentally skip
unintended stuff.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251117234033.345679-7-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 4f0638b124 ("net: phy: RTL8211FVD: Restore disabling of PHY-mode EEE")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb78b71faf ]
Previous changes have replaced the machine-level priv->phycr2 with a
high-level priv->disable_clk_out. This created a discrepancy with
priv->phycr1 which is resolved here, for uniformity.
One advantage of this new implementation is that we don't read
priv->phycr1 in rtl821x_probe() if we're never going to modify it.
We never test the positive return code from phy_modify_mmd_changed(), so
we could just as well use phy_modify_mmd().
I took the ALDPS feature description from commit d90db36a9e ("net:
phy: realtek: add dt property to enable ALDPS mode") and transformed it
into a function comment - the feature is sufficiently non-obvious to
deserve that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251117234033.345679-6-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 4f0638b124 ("net: phy: RTL8211FVD: Restore disabling of PHY-mode EEE")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1a31c41be ]
Add CLKOUT disable support for RTL8211F(D)(I)-VD-CG. Like with other PHY
variants, this feature might be requested by customers when the clock
output is not used, in order to reduce electromagnetic interference (EMI).
In the common driver, the CLKOUT configuration is done through PHYCR2.
The RTL_8211FVD_PHYID is singled out as not having that register, and
execution in rtl8211f_config_init() returns early after commit
2c67301584 ("net: phy: realtek: Avoid PHYCR2 access if PHYCR2 not
present").
But actually CLKOUT is configured through a different register for this
PHY. Instead of pretending this is PHYCR2 (which it is not), just add
some code for modifying this register inside the rtl8211f_disable_clk_out()
function, and move that outside the code portion that runs only if
PHYCR2 exists.
In practice this reorders the PHYCR2 writes to disable PHY-mode EEE and
to disable the CLKOUT for the normal RTL8211F variants, but this should
be perfectly fine.
It was not noted that RTL8211F(D)(I)-VD-CG would need a genphy_soft_reset()
call after disabling the CLKOUT. Despite that, we do it out of caution
and for symmetry with the other RTL8211F models.
Co-developed-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251117234033.345679-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 4f0638b124 ("net: phy: RTL8211FVD: Restore disabling of PHY-mode EEE")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 910ac7bfb1 ]
This variable is assigned in rtl821x_probe() and used in
rtl8211f_config_init(), which is more complex than it needs to be.
Simply testing the same condition from rtl821x_probe() in
rtl8211f_config_init() yields the same result (the PHY driver ID is a
runtime invariant), but with one temporary variable less.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251117234033.345679-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 4f0638b124 ("net: phy: RTL8211FVD: Restore disabling of PHY-mode EEE")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27033d0691 ]
The RTL8211F(D)(I)-VD-CG PHY also has support for disabling the CLKOUT,
and we'd like to introduce the "realtek,clkout-disable" property for
that.
But it isn't done through the PHYCR2 register, and it becomes awkward to
have the driver pretend that it is. So just replace the machine-level
"u16 phycr2" variable with a logical "bool disable_clk_out", which
scales better to the other PHY as well.
The change is a complete functional equivalent. Before, if the device
tree property was absent, priv->phycr2 would contain the RTL8211F_CLKOUT_EN
bit as read from hardware. Now, we don't save priv->phycr2, but we just
don't call phy_modify_paged() on it. Also, we can simply call
phy_modify_paged() with the "set" argument to 0.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20251117234033.345679-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 4f0638b124 ("net: phy: RTL8211FVD: Restore disabling of PHY-mode EEE")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cd7671ef4c ]
The enable_mpesw() function returns -EINVAL if ldev->mode is not
MLX5_LAG_MODE_NONE. This means attempting to enable MPESW mode when it's
already enabled will fail. In contrast, disable_mpesw() properly checks
if the mode is MLX5_LAG_MODE_MPESW before proceeding, making it
naturally idempotent and safe to call multiple times.
Fix enable_mpesw() to return success if mpesw is already enabled.
Fixes: a32327a3a0 ("net/mlx5: Lag, Control MultiPort E-Switch single FDB mode")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Shay Drori <shayd@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/1764602008-1334866-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
