With the previous patch, there is an extra watchdog read in each retry.
Now the total number of clocksource reads is increased to 4 per iteration.
In order to avoid increasing the clock skew check overhead, the default
maximum number of retries is reduced from 3 to 2 to maintain the same 12
clocksource reads in the worst case.
Suggested-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Since commit db3a34e174 ("clocksource: Retry clock read if long delays
detected") and commit 2e27e793e2 ("clocksource: Reduce clocksource-skew
threshold"), it is found that tsc clocksource fallback to hpet can
sometimes happen on both Intel and AMD systems especially when they are
running stressful benchmarking workloads. Of the 23 systems tested with
a v5.14 kernel, 10 of them have switched to hpet clock source during
the test run.
The result of falling back to hpet is a drastic reduction of performance
when running benchmarks. For example, the fio performance tests can
drop up to 70% whereas the iperf3 performance can drop up to 80%.
4 hpet fallbacks happened during bootup. They were:
[ 8.749399] clocksource: timekeeping watchdog on CPU13: hpet read-back delay of 263750ns, attempt 4, marking unstable
[ 12.044610] clocksource: timekeeping watchdog on CPU19: hpet read-back delay of 186166ns, attempt 4, marking unstable
[ 17.336941] clocksource: timekeeping watchdog on CPU28: hpet read-back delay of 182291ns, attempt 4, marking unstable
[ 17.518565] clocksource: timekeeping watchdog on CPU34: hpet read-back delay of 252196ns, attempt 4, marking unstable
Other fallbacks happen when the systems were running stressful
benchmarks. For example:
[ 2685.867873] clocksource: timekeeping watchdog on CPU117: hpet read-back delay of 57269ns, attempt 4, marking unstable
[46215.471228] clocksource: timekeeping watchdog on CPU8: hpet read-back delay of 61460ns, attempt 4, marking unstable
Commit 2e27e793e2 ("clocksource: Reduce clocksource-skew threshold"),
changed the skew margin from 100us to 50us. I think this is too small
and can easily be exceeded when running some stressful workloads on a
thermally stressed system. So it is switched back to 100us.
Even a maximum skew margin of 100us may be too small in for some systems
when booting up especially if those systems are under thermal stress. To
eliminate the case that the large skew is due to the system being too
busy slowing down the reading of both the watchdog and the clocksource,
an extra consecutive read of watchdog clock is being done to check this.
The consecutive watchdog read delay is compared against
WATCHDOG_MAX_SKEW/2. If the delay exceeds the limit, we assume that
the system is just too busy. A warning will be printed to the console
and the clock skew check is skipped for this round.
Fixes: db3a34e174 ("clocksource: Retry clock read if long delays detected")
Fixes: 2e27e793e2 ("clocksource: Reduce clocksource-skew threshold")
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
With CONFIG_PREEMPT_DYNAMIC=y, the kernel builds with CONFIG_PREEMPTION=y
because preemption can be enabled at runtime. This prevents any tests
of Tiny RCU or Tiny SRCU from running correctly. This commit therefore
explicitly sets CONFIG_PREEMPT_DYNAMIC=n for those scenarios.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Since the PMU callback runs in irq context, it synchronizes with gt
reset using the reset count. We could run into a case where the PMU
callback could read the reset count before it is updated. This has a
potential of corrupting the busyness stats.
In addition to the reset count, check if the reset bit is set before
capturing busyness.
In addition save the previous stats only if you intend to update them.
v2:
- The 2 reset counts captured in the PMU callback can end up being the
same if they were captured right after the count is incremented in the
reset flow. This can lead to a bad busyness state. Ensure that reset
is not in progress when the initial reset count is captured.
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211108211057.68783-1-umesh.nerlige.ramappa@intel.com
Kumar Kartikeya says:
====================
Three commits addressing comments for the typeless/weak ksym set. No functional
change intended. Hopefully this is simpler to read for kfunc as well.
====================
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Alexei pointed out that we can use BPF_REG_0 which already contains imm
from move_blob2blob computation. Note that we now compare the second
insn's imm, but this should not matter, since both will be zeroed out
for the error case for the insn populated earlier.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20211122235733.634914-4-memxor@gmail.com
Instead, jump directly to success case stores in case ret >= 0, else do
the default 0 value store and jump over the success case. This is better
in terms of readability. Readjust the code for kfunc relocation as well
to follow a similar pattern, also leads to easier to follow code now.
Suggested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20211122235733.634914-3-memxor@gmail.com
Stop using uie_unsupported and clear RTC_FEATURE_UPDATE_INTERRUPT instead.
Also, let the core know that the alarm will truncate seconds as it only has
a minute resolution.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20211109234750.107115-1-alexandre.belloni@bootlin.com
The only usage of irq_generic_chip_ops is to pass its address to
irq_domain_add_linear() which takes a pointer to const struct
irq_domain_ops. Make it const to allow the compiler to put it in
read-only memory.
[ tglx: Fixed subject prefix ]
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20211130214043.1257585-1-rikard.falkeborn@gmail.com
The pcf85063 driver regsitration currently supports the "compatible"
property type of matching (for DT).
This patch adds "matching by name" support to the driver by defining
an i2c_device_id table and setting the id_table parameter in the
i2c_driver struct.
This will, for example, make the driver easier to instantiate on
systems where CONFIG_OF is not enabled (x86 in my case).
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211116164733.17149-1-ferlandm@amotus.ca
Some thread flags can be set remotely, and so even when IRQs are disabled,
the flags can change under our feet. Generally this is unlikely to cause a
problem in practice, but it is somewhat unsound, and KCSAN will
legitimately warn that there is a data race.
To avoid such issues, a snapshot of the flags has to be taken prior to
using them. Some places already use READ_ONCE() for that, others do not.
Convert them all to the new flag accessor helpers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Link: https://lore.kernel.org/r/20211129130653.2037928-11-mark.rutland@arm.com
Some thread flags can be set remotely, and so even when IRQs are disabled,
the flags can change under our feet. Thus, when setting flags we must use
an atomic operation rather than a plain read-modify-write sequence, as a
plain read-modify-write may discard flags which are concurrently set by a
remote thread, e.g.
// task A // task B
tmp = A->thread_info.flags;
set_tsk_thread_flag(A, NEWFLAG_B);
tmp |= NEWFLAG_A;
A->thread_info.flags = tmp;
arch/powerpc/kernel/interrupt.c's system_call_exception() sets
_TIF_RESTOREALL in the thread info flags with a read-modify-write, which
may result in other flags being discarded.
Elsewhere in the file it uses clear_bits() to atomically remove flag bits,
so use set_bits() here for consistency with those.
There may be reasons (e.g. instrumentation) that prevent the use of
set_thread_flag() and clear_thread_flag() here, which would otherwise be
preferable.
Fixes: ae7aaecc3f ("powerpc/64s: system call rfscv workaround for TM bugs")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Eirik Fuller <efuller@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Link: https://lore.kernel.org/r/20211129130653.2037928-10-mark.rutland@arm.com
Some thread flags can be set remotely, and so even when IRQs are disabled,
the flags can change under our feet. Generally this is unlikely to cause a
problem in practice, but it is somewhat unsound, and KCSAN will
legitimately warn that there is a data race.
To avoid such issues, a snapshot of the flags has to be taken prior to
using them. Some places already use READ_ONCE() for that, others do not.
Convert them all to the new flag accessor helpers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Stafford Horne <shorne@gmail.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Link: https://lore.kernel.org/r/20211129130653.2037928-9-mark.rutland@arm.com
Some thread flags can be set remotely, and so even when IRQs are disabled,
the flags can change under our feet. Generally this is unlikely to cause a
problem in practice, but it is somewhat unsound, and KCSAN will
legitimately warn that there is a data race.
To avoid such issues, a snapshot of the flags has to be taken prior to
using them. Some places already use READ_ONCE() for that, others do not.
Convert them all to the new flag accessor helpers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20211129130653.2037928-8-mark.rutland@arm.com
Some thread flags can be set remotely, and so even when IRQs are disabled,
the flags can change under our feet. Generally this is unlikely to cause a
problem in practice, but it is somewhat unsound, and KCSAN will
legitimately warn that there is a data race.
To avoid such issues, a snapshot of the flags has to be taken prior to
using them. Some places already use READ_ONCE() for that, others do not.
Convert them all to the new flag accessor helpers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20211129130653.2037928-7-mark.rutland@arm.com
Some thread flags can be set remotely, and so even when IRQs are disabled,
the flags can change under our feet. Generally this is unlikely to cause a
problem in practice, but it is somewhat unsound, and KCSAN will
legitimately warn that there is a data race.
To avoid such issues, a snapshot of the flags has to be taken prior to
using them. Some places already use READ_ONCE() for that, others do not.
Convert them all to the new flag accessor helpers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211129130653.2037928-6-mark.rutland@arm.com
Some thread flags can be set remotely, and so even when IRQs are disabled,
the flags can change under our feet. Generally this is unlikely to cause a
problem in practice, but it is somewhat unsound, and KCSAN will
legitimately warn that there is a data race.
To avoid such issues, a snapshot of the flags has to be taken prior to
using them. Some places already use READ_ONCE() for that, others do not.
Convert them all to the new flag accessor helpers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Link: https://lore.kernel.org/r/20211129130653.2037928-5-mark.rutland@arm.com
Some thread flags can be set remotely, and so even when IRQs are disabled,
the flags can change under our feet. Generally this is unlikely to cause a
problem in practice, but it is somewhat unsound, and KCSAN will
legitimately warn that there is a data race.
To avoid such issues, a snapshot of the flags has to be taken prior to
using them. Some places already use READ_ONCE() for that, others do not.
Convert them all to the new flag accessor helpers.
The READ_ONCE(ti->flags) .. cmpxchg(ti->flags) loop in
set_nr_if_polling() is left as-is for clarity.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lore.kernel.org/r/20211129130653.2037928-4-mark.rutland@arm.com
Some thread flags can be set remotely, and so even when IRQs are disabled,
the flags can change under our feet. Generally this is unlikely to cause a
problem in practice, but it is somewhat unsound, and KCSAN will
legitimately warn that there is a data race.
To avoid such issues, a snapshot of the flags has to be taken prior to
using them. Some places already use READ_ONCE() for that, others do not.
Convert them all to the new flag accessor helpers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20211129130653.2037928-3-mark.rutland@arm.com
Some thread flags can be set remotely, and so even when IRQs are disabled,
the flags can change under our feet. Generally this is unlikely to cause a
problem in practice, but it is somewhat unsound, and KCSAN will
legitimately warn that there is a data race.
To avoid such issues, a snapshot of the flags has to be taken prior to
using them. Some places already use READ_ONCE() for that, others do not.
Convert them all to the new flag accessor helpers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Link: https://lore.kernel.org/r/20211129130653.2037928-12-mark.rutland@arm.com
In <linux/thread_info.h> there are helpers to manipulate individual thread
flags, but where code wants to check several flags at once, it must open
code reading current_thread_info()->flags and operating on a snapshot.
As some flags can be set remotely it's necessary to use READ_ONCE() to get
a consistent snapshot even when IRQs are disabled, but some code forgets to
do this. Generally this is unlike to cause a problem in practice, but it is
somewhat unsound, and KCSAN will legitimately warn that there is a data
race.
To make it easier to do the right thing, and to highlight that concurrent
modification is possible, add new helpers to snapshot the flags, which
should be used in preference to plain reads. Subsequent patches will move
existing code to use the new helpers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marco Elver <elver@google.com>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20211129130653.2037928-2-mark.rutland@arm.com
In order to make it possible to get battery voltage status, this commit
adds RTC_VL_READ, RTC_VL_CLR ioctl commands to rtc-rs5c372.
Signed-off-by: Camel Guo <camelg@axis.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211111083625.10216-1-camel.guo@axis.com
Switch SEV implementation to insn_decode_mmio(). The helper is going
to be used by TDX too.
No functional changes.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Tested-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lkml.kernel.org/r/20211130184933.31005-5-kirill.shutemov@linux.intel.com
In preparation for sharing MMIO instruction decode between SEV-ES and
TDX, factor out the common decode into a new insn_decode_mmio() helper.
For regular virtual machine, MMIO is handled by the VMM and KVM
emulates instructions that caused MMIO. But, this model doesn't work
for a secure VMs (like SEV or TDX) as VMM doesn't have access to the
guest memory and register state. So, for TDX or SEV VMM needs
assistance in handling MMIO. It induces exception in the guest. Guest
has to decode the instruction and handle it on its own.
The code is based on the current SEV MMIO implementation.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Tested-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lkml.kernel.org/r/20211130184933.31005-4-kirill.shutemov@linux.intel.com
The helper returns a pointer to the register indicated by
ModRM byte.
It's going to replace vc_insn_get_reg() in the SEV MMIO
implementation. TDX MMIO implementation will also use it.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Tested-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lkml.kernel.org/r/20211130184933.31005-3-kirill.shutemov@linux.intel.com
is_string_insn() calls insn_get_opcode() that can fail, but does not
handle the failure.
is_string_insn() interface does not allow to communicate an error to the
caller.
Push insn_get_opcode() to the only non-static user of is_string_insn()
and fail it early if insn_get_opcode() fails.
[ dhansen: fix tabs-versus-spaces breakage ]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Tested-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Link: https://lkml.kernel.org/r/20211130184933.31005-2-kirill.shutemov@linux.intel.com
This makes 'bridge-nf-filter-pppoe-tagged' sysctl work for
bridged traffic.
Looking at the original commit it doesn't appear this ever worked:
static unsigned int br_nf_post_routing(unsigned int hook, struct sk_buff **pskb,
[..]
if (skb->protocol == htons(ETH_P_8021Q)) {
skb_pull(skb, VLAN_HLEN);
skb->network_header += VLAN_HLEN;
+ } else if (skb->protocol == htons(ETH_P_PPP_SES)) {
+ skb_pull(skb, PPPOE_SES_HLEN);
+ skb->network_header += PPPOE_SES_HLEN;
}
[..]
NF_HOOK(... POST_ROUTING, ...)
... but the adjusted offsets are never restored.
The alternative would be to rip this code out for good,
but otoh we'd have to keep this anyway for the vlan handling
(which works because vlan tag info is in the skb, not the packet
payload).
Reported-and-tested-by: Amish Chana <amish@3g.co.za>
Fixes: 516299d2f5 ("[NETFILTER]: bridge-nf: filter bridged IPv4/IPv6 encapsulated in pppoe traffic")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Allow packet redirection to another interface upon egress.
[lukas: set skb_iif, add commit message, original patch from Pablo. ]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
net/netfilter/nfnetlink_queue.c:601:36: warning: variable 'ctinfo' is
uninitialized when used here [-Wuninitialized]
if (ct && nfnl_ct->build(skb, ct, ctinfo, NFQA_CT, NFQA_CT_INFO) < 0)
ctinfo is only uninitialized if ct == NULL. Init it to 0 to silence this.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
dying is bool, the type conversion to true/false value is not
needed.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Convention for all the other "lake" CPUs is all one word.
So s/RAPTOR_LAKE/RAPTORLAKE/
Fixes: fbdb5e8f29 ("x86/cpu: Add Raptor Lake to Intel family")
Reported-by: Rui Zhang <rui.zhang@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lkml.kernel.org/r/20211119170832.1034220-1-tony.luck@intel.com
Its no longer needed after commit 8702997074
("netfilter: nf_queue: move hookfn registration out of struct net").
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Kernel fails to compile with PARAVIRT_XXL=y if XEN_PV is not enabled:
ld.lld: error: undefined symbol: xen_iret
It happens because INTERRUPT_RETURN defined to use xen_iret if
CONFIG_PARAVIRT_XXL enabled regardless of CONFIG_XEN_PV.
The issue is not visible in the current kernel because CONFIG_XEN_PV is
the only user of CONFIG_PARAVIRT_XXL and there's no way to enable them
separately.
Rework code to define INTERRUPT_RETURN based on CONFIG_XEN_PV, not
CONFIG_PARAVIRT_XXL.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lkml.kernel.org/r/20211130185533.32658-1-kirill.shutemov@linux.intel.com
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring fields.
Use memset_startat() to avoid confusing memset() about writing beyond
the target struct member.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The dest variable is not used after ip_vs_new_dest anymore in
ip_vs_add_dest, do not need pass it to ip_vs_new_dest, remove it.
Signed-off-by: GuoYong Zheng <zhenggy@chinatelecom.cn>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In a typical read transfer, start completion flag is being set after
read finishes (notice ipd bit 4 being set):
trasnfer poll=0
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 33
This causes I2C transfer being aborted in polled mode from a stop completion
handler:
trasnfer poll=1
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 0
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 13
i2c stop
rk3x-i2c fdd40000.i2c: unexpected irq in STOP: 0x10
Clearing the START flag after read fixes the issue without any obvious
side effects.
This issue was dicovered on RK3566 when adding support for powering
off the RK817 PMIC.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit e8578547ce. Drivers
should read these values from ACPI tables.
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit 36af188f79. Drivers
should read these values from ACPI tables.
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
random.c is a bit understaffed, and folks want more prompt reviews. I've
got the crypto background and the interest to do these reviews, and have
authored parts of the file already.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Default KBUILD_IMAGE to $(boot)/bzImage if a self-extracting
(CONFIG_PARISC_SELF_EXTRACT=y) kernel is to be built.
This fixes the bindeb-pkg make target.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v4.14+
Joanne Koong says:
====================
This patchset add a new helper, bpf_loop.
One of the complexities of using for loops in bpf programs is that the verifier
needs to ensure that in every possibility of the loop logic, the loop will always
terminate. As such, there is a limit on how many iterations the loop can do.
The bpf_loop helper moves the loop logic into the kernel and can thereby
guarantee that the loop will always terminate. The bpf_loop helper simplifies
a lot of the complexity the verifier needs to check, as well as removes the
constraint on the number of loops able to be run.
From the test results, we see that using bpf_loop in place
of the traditional for loop led to a decrease in verification time
and number of bpf instructions by ~99%. The benchmark results show
that as the number of iterations increases, the overhead per iteration
decreases.
The high-level overview of the patches -
Patch 1 - kernel-side + API changes for adding bpf_loop
Patch 2 - tests
Patch 3 - use bpf_loop in strobemeta + pyperf600 and measure verifier performance
Patch 4 - benchmark for throughput + latency of bpf_loop call
v3 -> v4:
~ Address nits: use usleep for triggering bpf programs, fix copyright style
v2 -> v3:
~ Rerun benchmarks on physical machine, update results
~ Propagate original error codes in the verifier
v1 -> v2:
~ Change helper name to bpf_loop (instead of bpf_for_each)
~ Set max nr_loops (~8 million loops) for bpf_loop call
~ Split tests + strobemeta/pyperf600 changes into two patches
~ Add new ops_report_final helper for outputting throughput and latency
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Add benchmark to measure the throughput and latency of the bpf_loop
call.
Testing this on my dev machine on 1 thread, the data is as follows:
nr_loops: 10
bpf_loop - throughput: 198.519 ± 0.155 M ops/s, latency: 5.037 ns/op
nr_loops: 100
bpf_loop - throughput: 247.448 ± 0.305 M ops/s, latency: 4.041 ns/op
nr_loops: 500
bpf_loop - throughput: 260.839 ± 0.380 M ops/s, latency: 3.834 ns/op
nr_loops: 1000
bpf_loop - throughput: 262.806 ± 0.629 M ops/s, latency: 3.805 ns/op
nr_loops: 5000
bpf_loop - throughput: 264.211 ± 1.508 M ops/s, latency: 3.785 ns/op
nr_loops: 10000
bpf_loop - throughput: 265.366 ± 3.054 M ops/s, latency: 3.768 ns/op
nr_loops: 50000
bpf_loop - throughput: 235.986 ± 20.205 M ops/s, latency: 4.238 ns/op
nr_loops: 100000
bpf_loop - throughput: 264.482 ± 0.279 M ops/s, latency: 3.781 ns/op
nr_loops: 500000
bpf_loop - throughput: 309.773 ± 87.713 M ops/s, latency: 3.228 ns/op
nr_loops: 1000000
bpf_loop - throughput: 262.818 ± 4.143 M ops/s, latency: 3.805 ns/op
>From this data, we can see that the latency per loop decreases as the
number of loops increases. On this particular machine, each loop had an
overhead of about ~4 ns, and we were able to run ~250 million loops
per second.
Signed-off-by: Joanne Koong <joannekoong@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211130030622.4131246-5-joannekoong@fb.com
This patch tests bpf_loop in pyperf and strobemeta, and measures the
verifier performance of replacing the traditional for loop
with bpf_loop.
The results are as follows:
~strobemeta~
Baseline
verification time 6808200 usec
stack depth 496
processed 554252 insns (limit 1000000) max_states_per_insn 16
total_states 15878 peak_states 13489 mark_read 3110
#192 verif_scale_strobemeta:OK (unrolled loop)
Using bpf_loop
verification time 31589 usec
stack depth 96+400
processed 1513 insns (limit 1000000) max_states_per_insn 2
total_states 106 peak_states 106 mark_read 60
#193 verif_scale_strobemeta_bpf_loop:OK
~pyperf600~
Baseline
verification time 29702486 usec
stack depth 368
processed 626838 insns (limit 1000000) max_states_per_insn 7
total_states 30368 peak_states 30279 mark_read 748
#182 verif_scale_pyperf600:OK (unrolled loop)
Using bpf_loop
verification time 148488 usec
stack depth 320+40
processed 10518 insns (limit 1000000) max_states_per_insn 10
total_states 705 peak_states 517 mark_read 38
#183 verif_scale_pyperf600_bpf_loop:OK
Using the bpf_loop helper led to approximately a 99% decrease
in the verification time and in the number of instructions.
Signed-off-by: Joanne Koong <joannekoong@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211130030622.4131246-4-joannekoong@fb.com
This patch adds the kernel-side and API changes for a new helper
function, bpf_loop:
long bpf_loop(u32 nr_loops, void *callback_fn, void *callback_ctx,
u64 flags);
where long (*callback_fn)(u32 index, void *ctx);
bpf_loop invokes the "callback_fn" **nr_loops** times or until the
callback_fn returns 1. The callback_fn can only return 0 or 1, and
this is enforced by the verifier. The callback_fn index is zero-indexed.
A few things to please note:
~ The "u64 flags" parameter is currently unused but is included in
case a future use case for it arises.
~ In the kernel-side implementation of bpf_loop (kernel/bpf/bpf_iter.c),
bpf_callback_t is used as the callback function cast.
~ A program can have nested bpf_loop calls but the program must
still adhere to the verifier constraint of its stack depth (the stack depth
cannot exceed MAX_BPF_STACK))
~ Recursive callback_fns do not pass the verifier, due to the call stack
for these being too deep.
~ The next patch will include the tests and benchmark
Signed-off-by: Joanne Koong <joannekoong@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211130030622.4131246-2-joannekoong@fb.com