Mark the task as having a cached timestamp when set assign it, so we
can efficiently check if it needs updating post being scheduled back in.
This covers both the actual schedule out case, which would've flushed
the plug, and the preemption case which doesn't touch the plugged
requests (for many reasons, one of them being then we'd need to have
preemption disabled around plug state manipulation).
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Querying the current time is the most costly thing we do in the block
layer per IO, and depending on kernel config settings, we may do it
many times per IO.
None of the callers actually need nsec granularity. Take advantage of
that by caching the current time in the plug, with the assumption here
being that any time checking will be temporally close enough that the
slight loss of precision doesn't matter.
If the block plug gets flushed, eg on preempt or schedule out, then
we invalidate the cached clock.
On a basic peak IOPS test case with iostats enabled, this changes
the performance from:
IOPS=108.41M, BW=52.93GiB/s, IOS/call=31/31
IOPS=108.43M, BW=52.94GiB/s, IOS/call=32/32
IOPS=108.29M, BW=52.88GiB/s, IOS/call=31/32
IOPS=108.35M, BW=52.91GiB/s, IOS/call=32/32
IOPS=108.42M, BW=52.94GiB/s, IOS/call=31/31
IOPS=108.40M, BW=52.93GiB/s, IOS/call=32/32
IOPS=108.31M, BW=52.89GiB/s, IOS/call=32/31
to
IOPS=118.79M, BW=58.00GiB/s, IOS/call=31/32
IOPS=118.62M, BW=57.92GiB/s, IOS/call=31/31
IOPS=118.80M, BW=58.01GiB/s, IOS/call=32/31
IOPS=118.78M, BW=58.00GiB/s, IOS/call=32/32
IOPS=118.69M, BW=57.95GiB/s, IOS/call=32/31
IOPS=118.62M, BW=57.92GiB/s, IOS/call=32/31
IOPS=118.63M, BW=57.92GiB/s, IOS/call=31/32
which is more than a 9% improvement in performance. Looking at perf diff,
we can see a huge reduction in time overhead:
10.55% -9.88% [kernel.vmlinux] [k] read_tsc
1.31% -1.22% [kernel.vmlinux] [k] ktime_get
Note that since this relies on blk_plug for the caching, it's only
applicable to the issue side. But this is where most of the time calls
happen anyway. On the completion side, cached time stamping is done with
struct io_comp patch, as long as the driver supports it.
It's also worth noting that the above testing doesn't enable any of the
higher cost CPU items on the block layer side, like wbt, cgroups,
iocost, etc, which all would add additional time querying and hence
overhead. IOW, results would likely look even better in comparison with
those enabled, as distros would do.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Convert any user of ktime_get_ns() to use blk_time_get_ns(), and
ktime_get() to blk_time_get(), so we have a unified API for querying the
current time in nanoseconds or as ktime.
No functional changes intended, this patch just wraps ktime_get_ns()
and ktime_get() with a block helper.
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In preparation for moving time keeping into blk.h, move the cgroup
related code for timestamps in here too. This will help avoid a circular
dependency, and also moves it into a more appropriate header as this one
is private to the block layer code.
Leave struct bio_issue in blk_types.h as it's a proper time definition.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Share the main merge / split / integrity preparation code between the
cached request vs newly allocated request cases, and add comments
explaining the cached request handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240124092658.2258309-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a new helper to check if there is suitable cached request in
blk_mq_submit_bio. This removes open coded logic in blk_mq_submit_bio
and moves some checks that so far are in blk_mq_use_cached_rq to
be performed earlier. This avoids the case where we first do check
with the cached request but then later end up allocating a new one
anyway and need to grab a queue reference.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240124092658.2258309-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_mq_attempt_bio_merge has nothing to do with allocating a new
request, it avoids allocating a new request. Move the call out of
blk_mq_get_new_requests and into the only caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20240124092658.2258309-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, at the end of ath11k_mac_fill_reg_tpc_info(), the
reg_tpc_info struct is populated, including the following:
reg_tpc_info->is_psd_power = is_psd_power;
reg_tpc_info->eirp_power = eirp_power;
Kernel test robot complains on uninitialized symbol:
drivers/net/wireless/ath/ath11k/mac.c:7949
ath11k_mac_fill_reg_tpc_info() error: uninitialized symbol 'eirp_power'.
This is because there are some code paths that never set eirp_power, so
the assignment of reg_tpc_info->eirp_power can come from an
uninitialized variable. Functionally this is OK since the eirp_power
only has meaning when is_psd_power is true, and all code paths which set
is_psd_power to true also set eirp_power. However, to keep the robot
happy, always initialize eirp_power before use.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 92425f788f ("wifi: ath11k: fill parameters for vdev set tpc power WMI command")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401311243.NyXwWZxP-lkp@intel.com/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240202024011.11341-1-quic_bqiang@quicinc.com
Currently in ath11k_peer_assoc_h_he() rx_mcs_80 and rx_mcs_160
are used to calculate max_nss, see
if (support_160)
max_nss = min(rx_mcs_80, rx_mcs_160);
else
max_nss = rx_mcs_80;
Kernel test robot complains on uninitialized symbols:
drivers/net/wireless/ath/ath11k/mac.c:2321 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
drivers/net/wireless/ath/ath11k/mac.c:2321 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_160'.
drivers/net/wireless/ath/ath11k/mac.c:2323 ath11k_peer_assoc_h_he() error: uninitialized symbol 'rx_mcs_80'.
This is because there are some code paths that never set them, so
the assignment of max_nss can come from uninitialized variables.
This could result in some unknown issues since a wrong peer_nss
might be passed to firmware.
Change to initialize them to an invalid value at the beginning. This
makes sense because even max_nss gets an invalid value, due to either
or both of them being invalid, we can get an valid peer_nss with
following guard:
arg->peer_nss = min(sta->deflink.rx_nss, max_nss)
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 3db26ecf71 ("ath11k: calculate the correct NSS of peer for HE capabilities")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401311243.NyXwWZxP-lkp@intel.com/
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240202023547.11141-1-quic_bqiang@quicinc.com
To reduce power consumption enable 802.11 power save mode in
station mode. This allows both radio and CPU to sleep more.
Only enable the mode on WCN7850, other chips don't support it
for now.
To test that power save mode is running, run below command and
check there is no NULL Data frame seen by a sniffer:
iw dev <inf> set power_save off
And run below command, then check there is a NULL Data frame
in sniffer:
iw dev <inf> set power_save on
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240201035830.2534-1-quic_bqiang@quicinc.com
In a rather unusual arrangement in include/media/v4l2-vp9.h struct
v4l2_vp9_frame_symbol_counts has fields that are arrays of pointers, not a
pointer to an array, which is what's usually done.
Add support for such arrays of pointers to kernel-doc.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20240131084934.191226-1-sakari.ailus@linux.intel.com
Timur pointed this out before, and it just slipped my mind,
but this might help some things work better, around pcie power
management.
Cc: <stable@vger.kernel.org> # v6.7
Fixes: 8d55b0a940 ("nouveau/gsp: add some basic registry entries.")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240130032643.2498315-1-airlied@gmail.com
The example for PCI devices has some addressing errors. 'reg' is written
as if the parent bus is PCI, but the default bus for examples is 1
address and size cell. 'ranges' is defining config space with a
size of 0. Generally, config space should not be defined in
'ranges', only PCI memory and I/O spaces. Fix these issues by updating
the values with made-up, but valid values.
This was uncovered with recent dtschema changes.
Link: https://lore.kernel.org/r/20240122173514.935742-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Make the pattern matching node names a bit stricter to improve DTS
consistency. The pattern is restricted to -N suffixes to decimal
numbers.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20240109082511.15278-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Static FDPIC executable may get an executable stack even when it has
non-executable GNU_STACK segment. This happens when STACK segment has rw
permissions, but does not specify stack size. In that case FDPIC loader
uses permissions of the interpreter's stack, and for static executables
with no interpreter it results in choosing the arch-default permissions
for the stack.
Fix that by using the interpreter's properties only when the interpreter
is actually used.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20240118150637.660461-1-jcmvbkbc@gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
udf_load_logicalvolint() loads logical volume integrity descriptors.
Since there can be multiple blocks with LVIDs, we verify the contents of
only the last (prevailing) LVID found. However if we fail to load the
last LVID (either due to IO error or because it's checksum fails to
match), we never perform the verification of validity of the LVID we are
going to use. If such LVID contains invalid data, we can hit
out-of-bounds access or similar issues. Fix the problem by verifying
each LVID we are potentially going to accept.
Reported-by: Robert Morris <rtm@csail.mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
AFAICS there is no hardware restriction on where in ggtt
the hdcp gsc message object needs to be bound. And as it's
a regular shmem object we don't need it be in the mappabe
range either. So pin it high to make avoid needlessly
wasting the precious mappable range for it.
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231215110933.9188-3-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
intel_hdcp_component_init()->...->intel_hdcp_gsc_initialize_message()
will allocate ggtt address space for some hdcp gsc message thing.
That is currently being done way too early as we haven't even
taken over the BIOS fb yet. So this has the potential of corrupting
ggtt PTEs that need to be preserved until the BIOS fb takover
is done.
Only call intel_hdcp_component_init() once all the BIOS fb takeover,
and full ggtt init (which currently also needs to reserve very
specific ranges of ggtt, thus assuming that no one else has stolen
them yet) is done.
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Alan Previn <alan.previn.teres.alexis@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231215110933.9188-2-ville.syrjala@linux.intel.com
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
The check in nand_base.c, nand_scan_tail() : has the following code:
(ecc->steps * ecc->size != mtd->writesize) which fails for some NAND chips.
Remove ECC entries in this driver which are not integral multiplications,
and adjust the number of chunks for entries which fails the above
calculation so it will calculate correctly (this was previously done
automatically before the check and was removed in a later commit).
Fixes: 68c18dae68 ("mtd: rawnand: marvell: add missing layouts")
Cc: stable@vger.kernel.org
Signed-off-by: Elad Nachman <enachman@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Below race may cause NULL pointer dereference
P1 P2
dquot_free_inode quota_off
drop_dquot_ref
remove_dquot_ref
dquots = i_dquot(inode)
dquots = i_dquot(inode)
srcu_read_lock
dquots[cnt]) != NULL (1)
dquots[type] = NULL (2)
spin_lock(&dquots[cnt]->dq_dqb_lock) (3)
....
If dquot_free_inode(or other routines) checks inode's quota pointers (1)
before quota_off sets it to NULL(2) and use it (3) after that, NULL pointer
dereference will be triggered.
So let's fix it by using a temporary pointer to avoid this issue.
Signed-off-by: Wang Jianjian <wangjianjian3@huawei.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20240202081852.2514092-1-wangjianjian3@huawei.com>
The Keystone platforms used their own keystone_defconfig mostly to
enable CONFIG_ARM_LPAE which could not be added to the multi_v7 config.
Now that we have multi_v7_lpae_defconfig/lpae.config target we can and
should use that defconfig for Keystone. Add the remaining must-have
options for Keystone support to multi_v7_defconfig.
TI_SCI_*:
TI_MESSAGE_MANAGER:
Allows TI-SCI communication with system control firmware (PMMC) on K2G.
TI_KEYSTONE_NETCP*:
KEYSTONE_NAVIGATOR*:
Network driver, needed for NFS boot.
PCI_KEYSTONE*:
CAN_C_CAN*:
INPUT_GPIO_DECODER:
SPI_CADENCE_QUADSPI:
PWM_TIECAP:
Miscellaneous on-chip peripherals. Added as modules where possible.
RESET_TI*:
Used by DSP Remoteproc driver.
bloat-o-meter:
add/remove: 387/0 grow/shrink: 6/0 up/down: 130945/0 (130945)
Total: Before=22791863, After=22922808, chg +0.57%
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240125163145.87055-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
A recent change to check_for_locks() changed it to take ->flc_lock while
holding ->fi_lock. This creates a lock inversion (reported by lockdep)
because there is a case where ->fi_lock is taken while holding
->flc_lock.
->flc_lock is held across ->fl_lmops callbacks, and
nfsd_break_deleg_cb() is one of those and does take ->fi_lock. However
it doesn't need to.
Prior to v4.17-rc1~110^2~22 ("nfsd: create a separate lease for each
delegation") nfsd_break_deleg_cb() would walk the ->fi_delegations list
and so needed the lock. Since then it doesn't walk the list and doesn't
need the lock.
Two actions are performed under the lock. One is to call
nfsd_break_one_deleg which calls nfsd4_run_cb(). These doesn't act on
the nfs4_file at all, so don't need the lock.
The other is to set ->fi_had_conflict which is in the nfs4_file.
This field is only ever set here (except when initialised to false)
so there is no possible problem will multiple threads racing when
setting it.
The field is tested twice in nfs4_set_delegation(). The first test does
not hold a lock and is documented as an opportunistic optimisation, so
it doesn't impose any need to hold ->fi_lock while setting
->fi_had_conflict.
The second test in nfs4_set_delegation() *is* make under ->fi_lock, so
removing the locking when ->fi_had_conflict is set could make a change.
The change could only be interesting if ->fi_had_conflict tested as
false even though nfsd_break_one_deleg() ran before ->fi_lock was
unlocked. i.e. while hash_delegation_locked() was running.
As hash_delegation_lock() doesn't interact in any way with nfs4_run_cb()
there can be no importance to this interaction.
So this patch removes the locking from nfsd_break_one_deleg() and moves
the final test on ->fi_had_conflict out of the locked region to make it
clear that locking isn't important to the test. It is still tested
*after* vfs_setlease() has succeeded. This might be significant and as
vfs_setlease() takes ->flc_lock, and nfsd_break_one_deleg() is called
under ->flc_lock this "after" is a true ordering provided by a spinlock.
Fixes: edcf972515 ("nfsd: fix RELEASE_LOCKOWNER")
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
HDMI audio can be enabled over AM62A-SK using the same DT overlay that
is used for AM625 / AM62-LP SK-EVMs.
Add the sk.dtb + hdmi-audio.dtbo combination for AM62A7-SK as well, to
check for overlay applicability during DTBS compile tests.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240201125452.1920623-4-a-bhatia1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The DSS outputs DPI signals via its second video port (VP2). The DPI
output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
transmitter (SIL9022) on the board.
Add pinmux info for DSS DPI output.
Add DT nodes for SIL9022 HDMI transmitter (TX), and the HDMI connector
on the AM62A7-SK platforms.
Additionally, connect the output of DSS (VP2) with input of the HDMI TX,
and the output of HDMI TX to the input of the HDMI connector.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240201125452.1920623-3-a-bhatia1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add Display SubSystem (DSS) DT node for the AM62A7 SoC.
The DSS supports one each of video pipeline (vid) and video-lite
pipeline (vidl1). The video port 1 (vp1) is tied-off in AM62A SoC, but
the pipeline remains active. The video port 2 (vp2) outputs the DPI
signals. Both the video ports are connected to the pipelines via 2
identical overlay managers (ovr1 and ovr2).
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Link: https://lore.kernel.org/r/20240201125452.1920623-2-a-bhatia1@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable the CPSW MDIO node, and link the pinctrl information to enable
ethernet on SK-AM62P.
Ethernet was unintentally broken on this board, even though these nodes
were already present, as enabling them was missed in the original
patch.
Fixes: c00504ea42 ("arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM")
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240201-am62p_cpsw_mdio-v1-1-05f758300f6e@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CAN instances 0 and 1 in the mcu domain are brought on the common
processor board through headers J30 and J31 respectively. Thus, add
their respective transceivers 1 and 2 dt nodes to add support for
these CAN instances.
CAN instance 3 in the main domain is brought on the common
processor board through header J27. The CAN High and Low lines
from the SoC are routed through a mux on the SoM. The select lines need
to be set for the CAN signals to get connected to the transceiver 3 on
the common processor board. Therefore, add transceiver dt nodes to add
support for this CAN instance.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240130102044.120483-4-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CAN instance 0 in the main domain is brought on the J7200 SoM through
header J1. Thus, Add transceiver dt node to add support for this CAN
instance.
Also, add the mux dt nodes to route CAN High and Low lines coming
from the SoC to the Common Processor Board.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240130102044.120483-3-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add support for 18 CAN controllers in main domain and 2 CAN controllers
present in mcu domain. All the CAN controllers support classic CAN
messages as well as CAN_FD messages.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240130102044.120483-2-b-kapoor@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add TPM device to Mallow device tree file, the device is connected to
the SoC with SPI1/CS1, the same SPI interface is also available on an
extension header together with an additional CS0 signal.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20240126165136.28543-1-francesco@dolcini.it
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Since spi-rockchip enables use_gpio_descriptors and the
SPI_CONTROLLER_GPIO_SS flag, the spi subsytem may call set_cs()
for spi devices with indexes above ROCKCHIP_SPI_MAX_CS_NUM
Remove array cs_asserted[] which held a shadow copy of the state
of the chip select lines with the only purpose of optimizing out
rewriting a chip select line to the current state (no-op)
This case is already handled by spi.c
Signed-off-by: Luis de Arquer <luis.dearquer@inertim.com>
Link: https://lore.kernel.org/r/d0a0c4b94f933f7f43973c34765214303ee82b77.camel@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If there are two flash chips connected flash regions can refer to the
second chip too. In this case we may see the following warning:
mtd: partition "BIOS" extends beyond the end of device "0000:00:1f.5" --
size truncated to 0x400000
For this reason, check the BIOS partition size against the chip size and
make sure it stays within the that.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20240201121638.207632-2-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This avoid duplicating the same macros in multiple drivers by reusing
the common AXI macros for the version register.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240202213132.3863124-2-dlechner@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The core SPI code will handle splitting transfers if needed as long
as ctlr->max_transfer_size is implemented. It does this in
__spi_pump_transfer_message() immediately before calling
ctlr->prepare_message. So effectively, this change does not
alter the behavior of the driver.
Also, several peripheral drivers make use of spi_max_transfer_size(),
so this should improve compatibility with those drivers.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240126220024.3926403-2-dlechner@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This moves splitting transfers for CS_WORD software emulation to the
same place where we split transfers for controller-specific reasons.
This fixes a few subtle bugs.
The calculation for maxsize was wrong for bit sizes between 17 and 24.
This is fixed by making use of spi_split_transfers_maxwords() which
already has the correct calculation.
Also, since this indirectly calls spi_res_alloc(), to avoid leaking
resources, spi_finalize_current_message() would need to be called
on all error paths in __spi_validate() and callers of __spi_validate()
would need to do the same. This is fixed by moving the call to
__spi_pump_transfer_message() where it is already splitting transfers
for other reasons and correctly releases resources in the subsequent
error paths.
Fixes: cbaa62e009 ("spi: add software implementation for SPI_CS_WORD")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20240126212358.3916280-2-dlechner@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use dev_err_probe() for all messages in dspi_request_dma() for the sake of
making them uniform. While at it, fix indentation issue reported by Vladimir
Oltean.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240204203127.1186621-3-andy.shevchenko@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dmaengine_slave_config() may return different error codes based on
the circumstances. Preserve it instead of shadowing to -EINVAL.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240204203127.1186621-2-andy.shevchenko@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When regmap consists of single register, 'regmap' subsystem is unable to
understand whether ->max_register is set or not, because in both cases it
is equal to zero. It leads to that the logic based on value of
->max_register doesn't work. For example using of REGCACHE_FLAT fails.
This patch introduces an extra parameter to regmap config, indicating
that zero value in ->max_register is authentic.
Signed-off-by: Jan Dakinevich <jan.dakinevich@salutedevices.com>
Link: https://lore.kernel.org/r/20240126200836.1829995-1-jan.dakinevich@salutedevices.com
Signed-off-by: Mark Brown <broonie@kernel.org>
'config SND_PXA2XX_AC97' is already present in sound/arm/Kconfig with
a prompt.
Commit 734c2d4bb7 ("[ALSA] ASoC pxa2xx build support") redundantly
added the second one to sound/soc/pxa/Kconfig.
Remove it.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20240204091424.38306-1-masahiroy@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_WCD939X has an optional dependency on TYPEC, so the newly added
SND_SOC_WCD939X_SDW option that selects it needs the same dependency, otherwise
it can fail randconfig builds like:
WARNING: unmet direct dependencies detected for SND_SOC_WCD939X
Depends on [m]: SOUND [=y] && SND [=y] && SND_SOC [=y] && SND_SOC_WCD939X_SDW [=y] && (SOUNDWIRE [=y] || !SOUNDWIRE [=y]) && (TYPEC [=m]
|| !TYPEC [=m])
Selected by [y]:
- SND_SOC_WCD939X_SDW [=y] && SOUND [=y] && SND [=y] && SND_SOC [=y] && SOUNDWIRE [=y]
arm-linux-gnueabi-ld: sound/soc/codecs/wcd939x.o: in function `wcd939x_soc_codec_remove':
wcd939x.c:(.text+0x1950): undefined reference to `wcd_clsh_ctrl_free'
arm-linux-gnueabi-ld: sound/soc/codecs/wcd939x.o: in function `wcd939x_codec_ear_dac_event':
wcd939x.c:(.text+0x35d8): undefined reference to `wcd_clsh_ctrl_set_state'
arm-linux-gnueabi-ld: sound/soc/codecs/wcd939x.o: in function `wcd939x_codec_enable_hphr_pa':
wcd939x.c:(.text+0x39b0): undefined reference to `wcd_clsh_ctrl_set_state'
arm-linux-gnueabi-ld: wcd939x.c:(.text+0x39dc): undefined reference to `wcd_clsh_set_hph_mode'
arm-linux-gnueabi-ld: wcd939x.c:(.text+0x3bc0): undefined reference to `wcd_clsh_ctrl_set_state'
Fixes: be2af391ce ("ASoC: codecs: Add WCD939x Soundwire devices driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240204212207.3158914-2-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd-amd-sdw-acpi.ko module is under CONFIG_SND_SOC_AMD_ACP_COMMON but
selected from SoF, which causes build failures in some randconfig builds
that enable SOF but not ACP:
WARNING: unmet direct dependencies detected for SND_AMD_SOUNDWIRE_ACPI
Depends on [n]: SOUND [=m] && SND [=m] && SND_SOC [=m] && SND_SOC_AMD_ACP_COMMON [=n] && ACPI [=y]
Selected by [m]:
- SND_SOC_SOF_AMD_SOUNDWIRE_LINK_BASELINE [=m] && SOUND [=m] && SND [=m] && SND_SOC [=m] && SND_SOC_SOF_TOPLEVEL [=y] && SND_SOC_SOF_AMD_TOPLEVEL [=m] && ACPI [=y]
ERROR: modpost: "amd_sdw_scan_controller" [sound/soc/sof/amd/snd-sof-amd-acp.ko] undefined!
Change the Makefile and Kconfig to allow it to get built regardless
of CONFIG_SND_SOC_AMD_ACP_COMMON.
Fixes: d948218424 ("ASoC: SOF: amd: add code for invoking soundwire manager helper functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240204212207.3158914-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
