Synchronise the headphone ilimit work functions when removing the
component. These can only trigger whilst the headphone is enabled which
shouldn't be possible once the component is removed but the works rely
on the stashed component pointer so they should be shut down before the
code moves on from component remove.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240202140619.1068560-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the component is removed the stashed component pointer in the
CODECs private struct should also be cleared to prevent use of a stale
pointer.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240202140619.1068560-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For DMA mode, the bus width of the DMA is equal to the size of data
word, so burst length should be configured as bits per word.
For CPU mode, because of the spi transfer len is in byte, so calculate
the total number of words according to spi transfer len and bits per
word, burst length should be configured as total data bits.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Clark Wang <xiaoning.wang@nxp.com>
Fixes: e9b220aeac ("spi: spi-imx: correctly configure burst length when using dma")
Fixes: 5f66db08cb ("spi: imx: Take in account bits per word instead of assuming 8-bits")
Link: https://lore.kernel.org/r/20240204091912.36488-1-carlos.song@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The tascodec_init() of the snd-soc-tas2781-comlib module is called from
snd-soc-tas2781-i2c and snd-hda-scodec-tas2781-i2c modules. It calls
request_firmware_nowait() with parameter THIS_MODULE and a cont/callback
from the latter modules.
The latter modules can be removed while their callbacks are running,
resulting in a general protection failure.
Add module parameter to tascodec_init() so request_firmware_nowait() can
be called with the module of the callback.
Fixes: ef3bcde75d ("ASoC: tas2781: Add tas2781 driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/118dad922cef50525e5aab09badef2fa0eb796e5.1707076603.git.soyer@irl.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
Recent changes modified operation-order in the probe() function without
updating its error path accordingly. If snd_hdac_i915_init() exists with
status EPROBE_DEFER the error path must cleanup allocated IRQs before
leaving the scope.
Fixes: 2dddc514b6 ("ASoC: Intel: avs: Move snd_hdac_i915_init to before probe_work.")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20240202114901.1002127-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The servers for the @codeaurora domain have long been retired and any
messages sent there bounce. Srinivasa Rao Mandadapu has left the
company and there does not appear to be an updated address to suggest,
so drop Srinivasa as maintainer of the binding. The binding still
appears to be maintined as Judy is listed.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240202174313.4113670-1-quic_jhugo@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It looks like the "!" character was added accidentally. The
regmap_update_bits_check() function is normally going to succeed. This
means the rest of the function is unreachable and we don't handle the
situation where "changed" is true correctly.
Fixes: 07f7d6e7a1 ("ASoC: cs35l56: Fix for initializing ASP1 mixer registers")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/0c254c07-d1c0-4a5c-a22b-7e135cab032c@moroto.mountain
Signed-off-by: Mark Brown <broonie@kernel.org>
This node is an example node for the PCIe controller in "endpoint" mode.
By default the controller is in "root complex" mode and there is already a
DT node for the same.
Examples should go in the bindings or other documentation.
Remove this node.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124183659.149119-4-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
These nodes are example nodes for the PCIe controller in "endpoint" mode.
By default the controller is in "root complex" mode and there is already a
DT node for the same.
Examples should go in the bindings or other documentation.
Remove this node.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124183659.149119-3-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This node is an example node for the PCIe controller in "endpoint" mode.
By default the controller is in "root complex" mode and there is already a
DT node for the same.
Examples should go in the bindings or other documentation.
Remove this node.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124183659.149119-2-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
PCIe node defined in the top-level J7200 SoC dtsi file is incomplete
and will not be functional unless it is extended with a SerDes PHY.
As the PHY and mode is only known at the board integration level, this
node should only be enabled when provided with this information.
Disable the PCIe node in the dtsi files and only enable when it is
actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240124183659.149119-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-11-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-10-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-9-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-8-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-7-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-6-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-5-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-4-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-3-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-2-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Each "mboxes" item is composed of two cells. It seems these got split
as they appeared to be two items in an array, but are actually a single
two-cell item. Rejoin these cells.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20240123222536.875797-1-afd@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The phyBOARD-Electra populates a TPM module on SPI0 bus.
Add support for the Infineon SLB9670 TPM module.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240123102921.1348777-1-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The clock on the ethernet1 PHY is turned on by default. This turns
the clock off as we do not use it.
Signed-off-by: Nathan Morrisson <nmorrisson@phytec.com>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240119225257.403222-1-nmorrisson@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
memory node are required for bootloader operation on TI K3 J784S4 EVM
and AM69-SK boards for finding the memory size during early boot stage.
So, align Linux device tree by adding phase tag marking 'bootph-all',
which is to enable for all bootloader stages.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Link: https://lore.kernel.org/r/20240119171619.3759205-1-a-nandan@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The beagleplay dts was using a bit-bang gpio mdio bus as a work-around
for errata i2329. However since commit d04807b806 ("net: ethernet: ti:
davinci_mdio: Add workaround for errata i2329") the mdio driver itself
already takes care of this errata for effected silicon, which landed
well before the beagleplay dts. So i suspect the reason for the
workaround in upstream was simply due to copying the vendor dts.
Switch the dts to the ti,cpsw-mdio instead so it described the actual
hardware and is consistent with other AM625 based boards
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240112124505.2054212-1-sjoerd@collabora.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The USB0 port on the beagleplay can be used for DFU booting. To enable
that functionality mark with bootph-all.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Link: https://lore.kernel.org/r/20240112091745.1896922-3-sjoerd@collabora.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The USB0 port on the AM62x SK can be used for DFU booting. To enable
that functionality mark with bootph-all.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Link: https://lore.kernel.org/r/20240112091745.1896922-2-sjoerd@collabora.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Extend the support for LZ4 compression to be used with hibernation.
The main idea is that different compression algorithms
have different characteristics and hibernation may benefit when it uses
any of these algorithms: a default algorithm, having higher
compression rate but is slower(compression/decompression) and a
secondary algorithm, that is faster(compression/decompression) but has
lower compression rate.
LZ4 algorithm has better decompression speeds over LZO. This reduces
the hibernation image restore time.
As per test results:
LZO LZ4
Size before Compression(bytes) 682696704 682393600
Size after Compression(bytes) 146502402 155993547
Decompression Rate 335.02 MB/s 501.05 MB/s
Restore time 4.4s 3.8s
LZO is the default compression algorithm used for hibernation. Enable
CONFIG_HIBERNATION_COMP_LZ4 to set the default compressor as LZ4.
Signed-off-by: Nikhil V <quic_nprakash@quicinc.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
gcc-11 seems to believe that the coeffs variable can be used
uninitialized. Refactor the code and remove the cscen variable to
convince gcc that we are doing a good job.
drivers/media/platform/nxp/imx8-isi/imx8-isi-hw.c:218:20: warning: 'coeffs' may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240128-gcc-11-warnings-v1-1-52bbdf492049@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
All the sink pads of the crossbar switch require an active link if
they're part of the pipeline. Mark them with the
MEDIA_PAD_FL_MUST_CONNECT flag to fail pipeline validation if they're
not connected. This allows removing a manual check when translating
streams.
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The MEDIA_PAD_FL_MUST_CONNECT flag indicates that the pad requires an
enabled link to stream, but only if it has any link at all. This makes
little sense, as if a pad is part of a pipeline, there are very few use
cases for an active link to be mandatory only if links exist at all. A
review of in-tree drivers confirms they all need an enabled link for
pads marked with the MEDIA_PAD_FL_MUST_CONNECT flag.
Expand the scope of the flag by rejecting pads that have no links at
all. This requires modifying the pipeline build code to add those pads
to the pipeline.
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The pad local variable in the media_pipeline_explore_next_link()
function is used to store the pad through which the entity has been
reached. Rename it to origin to reflect that and make the code easier to
read. This will be even more important in subsequent commits when
expanding the function with additional logic.
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Maintain a counter of the links connected to a pad in the media_pad
structure. This helps checking if a pad is connected to anything, which
will be used in the pipeline building code.
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When translating source to sink streams in the crossbar subdev, the
driver tries to locate the remote subdev connected to the sink pad. The
remote pad may be NULL, if userspace tries to enable a stream that ends
at an unconnected crossbar sink. When that occurs, the driver
dereferences the NULL pad, leading to a crash.
Prevent the crash by checking if the pad is NULL before using it, and
return an error if it is.
Cc: stable@vger.kernel.org # 6.1
Fixes: cf21f328fc ("media: nxp: Add i.MX8 ISI driver")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20231201150614.63300-1-marex@denx.de
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The media_create_pad_link() function doesn't correctly clear reject link
type flags, nor does it set the DATA_LINK flag. It only works because
the MEDIA_LNK_FL_DATA_LINK flag's value is 0.
Fix it by returning an error if any link type flag is set. This doesn't
introduce any regression, as nobody calls the media_create_pad_link()
function with link type flags (easily checked by grepping for the flag
in the source code, there are very few hits).
Set the MEDIA_LNK_FL_DATA_LINK explicitly, which is a no-op that the
compiler will optimize out, but is still useful to make the code more
explicit and easier to understand.
Cc: stable@vger.kernel.org # 6.1
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When building pipelines by following links, the
media_pipeline_explore_next_link() function only traverses enabled
links. The remote pad of a disabled link is not added to the pipeline,
and neither is the local pad. While the former is correct as disabled
links should not be followed, not adding the local pad breaks processing
of the MEDIA_PAD_FL_MUST_CONNECT flag.
The MEDIA_PAD_FL_MUST_CONNECT flag is checked in the
__media_pipeline_start() function that iterates over all pads after
populating the pipeline. If the pad is not present, the check gets
skipped, rendering it useless.
Fix this by adding the local pad of all links regardless of their state,
only skipping the remote pad for disabled links.
Cc: stable@vger.kernel.org # 6.1
Fixes: ae21987283 ("media: mc: entity: Rewrite media_pipeline_start()")
Reported-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Closes: https://lore.kernel.org/linux-media/7658a15a-80c5-219f-2477-2a94ba6c6ba1@kontron.de
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Currently for hibernation, LZO is the only compression algorithm
available and uses the existing LZO library calls. However, there
is no flexibility to switch to other algorithms which provides better
results. The main idea is that different compression algorithms have
different characteristics and hibernation may benefit when it uses
alternate algorithms.
By moving to crypto based APIs, it lays a foundation to use other
compression algorithms for hibernation. There are no functional changes
introduced by this approach.
Signed-off-by: Nikhil V <quic_nprakash@quicinc.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Renaming lzo* to generic names, except for lzo_xxx() APIs. This is
used in the next patch where we move to crypto based APIs for
compression. There are no functional changes introduced by this
approach.
Signed-off-by: Nikhil V <quic_nprakash@quicinc.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Simplify the system-wide suspend of devices by invoking dpm_async_fn()
directly from the main loop in each suspend phase instead of using an
additional wrapper function for running it.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
During a system-wide suspend of devices, dpm_noirq_suspend_devices(),
dpm_suspend_late() and dpm_suspend() move devices from one list to
another. They do it with each device after its PM callback in the
given suspend phase has run or has been scheduled for asynchronous
execution, in case it is deleted from the current list in the
meantime.
However, devices can be moved to a new list before invoking their PM
callbacks (which usually is the case for the devices whose callbacks
are executed asynchronously anyway), because doing so does not affect
the ordering of that list. In either case, each device is moved to
the new list after the previous device has been moved to it or gone
away, and if a device is removed, it does not matter which list it is
in at that point, because deleting an entry from a list does not change
the ordering of the other entries in it.
Accordingly, modify the functions mentioned above to move devices to
new lists without waiting for their PM callbacks to run regardless of
whether or not they run asynchronously.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The async_error and pm_transition variables are set under dpm_list_mtx
in multiple places in the system-wide device PM core code, which is
unnecessary and confusing, so rearrange the code so that the variables
in question are set before acquiring the lock.
While at it, add some empty code lines around locking to improve the
consistency of the code.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
The error logging and failure statistics updates are carried out in two
places in each system-wide device suspend phase, which is unnecessary
code duplication, so do that in one place in each phase, right after
invoking device suspend callbacks.
While at it, add "noirq" or "late" to the "async" string printed when
the failing device callback in the "noirq" or "late" suspend phase,
respectively, was run asynchronously.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Because dpm_save_failed_dev() may be called simultaneously by multiple
failing device PM functions, the state of the suspend_stats fields
updated by it may become inconsistent.
Prevent that from happening by using a lock in dpm_save_failed_dev().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
If the handling of two or more devices fails in one suspend-resume
phase, it should be counted once in the statistics which is not
guaranteed to happen during system-wide resume of devices due to
the possible asynchronous execution of device callbacks.
Address this by using the async_error static variable during system-wide
device resume to indicate that there has been a device resume error and
the given suspend-resume phase should be counted as failing.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
It is not necessary to define struct suspend_stats in a header file and the
suspend_stats variable in the core device system-wide PM code. They both
can be defined in kernel/power/main.c, next to the sysfs and debugfs code
accessing suspend_stats, which can be static.
Modify the code in question in accordance with the above observation and
replace the static inline functions manipulating suspend_stats with
regular ones defined in kernel/power/main.c.
While at it, move the enum suspend_stat_step to the end of suspend.h which
is a more suitable place for it.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
While reviewing the hyperbus sfdp proposal the following problem was
noticed:
In file included from ./include/linux/mtd/gen_probe.h:10,
from drivers/mtd/hyperbus/hyperbus-sfdp.c:6:
./include/linux/mtd/flashchip.h:77:9: error: unknown type name ‘wait_queue_head_t’
77 | wait_queue_head_t wq; /* Wait on here when we're waiting for the chip
| ^~~~~~~~~~~~~~~~~
It is good practice to directly include all headers used, it avoids
implicit dependencies and spurious breakage if someone rearranges
headers and causes the implicit include to vanish.
Explicitly include <linux/wait.h> in include/linux/mtd/flashchip.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240205100955.149755-1-tudor.ambarus@linaro.org
Change the type of the "success" and "fail" fields in struct
suspend_stats to unsigned int, because they cannot be negative.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
