Add tx_sop_type to tcpm_pd_send_control and rx_sop_type to
tcpm_pd_ctrl_request. TCPC_TX_SOP is added to all pd_send_control calls,
but TCPC_TX_SOP_PRIME is added to pd_send_control for a SOFT_RESET message
sent after a Vconn swap that makes the Port the Vconn source. Likewise,
tcpm_pd_ctrl_request resets the proper protocol layer depending on
rx_sop_type for SOFT_RESET.
VCONN_SWAP_TURN_ON_VCONN now moves to a new state,
VCONN_SWAP_SEND_SOFT_RESET. This state sends SOFT_RESET over SOP' before
transitioning to the ready state if applicable. It transitions after
PD_T_VCONN_STABLE, definied in pd.h as the time required for Vconn to be
on before transmitting messages.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-20-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add negotiated revision and tx/rx message ids to tcpm_port specific to
SOP'. tx_sop_type is added to the tcpm_port to determine whether the
current constructed message will be sent over SOP or SOP' if not
sent immediately.
tcpm_pd_rx_handler updates the received message ids. SOP* messages are not
processed afterwards. The handler also calls tcpm_can_communicate_sop_prime
to determine if a SOP' message is directed towards the port, and drops SOP'
messages it should not respond to.
tcpm_can_communicate_sop_prime is added as a helper to determine whether
the port is capable of communicating over SOP' at a given moment. Being
the Vconn source is a requirement in Power Delivery 3.0 but only a
recommendation in Power Delviery 2.0. Because the port should ensure that
the cable is powered before communication, always enforce the port is the
Vconn source regardless of revision.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-19-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpm_pd_receive adds the SOP type as a parameter, and passes it within the
pd_rx_event struct for tcpm_pd_rx_handler to use. For now, the handler
drops all SOP' messages.
Maxim based tcpci drivers are capable of SOP' communication, so process_rx
now takes the SOP type into account and passes the value to
tcpm_pd_receive.
tcpci_set_pd_rx now utilizes the cable_comm_capable flag to determine if
TCPC_RX_DETECT_SOP1 should be added to the bitfield when enabling PD
message reception.
For all other consumers of tcpm_pd_receive, default the new field to
TCPC_TX_SOP.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-18-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add cable_comm_capable to tcpci_data for tcpci drivers to indicate that
the port tcpc is capable of communicating to cables over SOP. A
corresponding tcpci callback tcpci_cable_comm_capable returns this value.
The tcpm will primarily use this in later patches to determine if the port
can transmit and receive SOP' messages.
Maxim based tcpci drivers are capable of SOP' communication, so the
cable_comm_capable flag is set to true.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-17-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add typec_cable_set_svdm_version and typec_get_cable_svdm version symbols.
Cables can operate under a lower PD revision than the port partner, and the
max SVDM version is tied to the PD revision. So, typec_cable maintains its
own svdm_version.
Add typec_altmode_get_cable_svdm_version to return the cable's negotiated
svdm_version for altmode drivers to use.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-16-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add typec_cable_ops struct for enter, exit, and vdm. The struct is added
to typec_altmode so port alt modes can have access to partner and cable
specific callbacks, and alt mode drivers can specify operations over SOP'
and SOP'' without modifying the existing API.
typec_port_register_cable_ops is added as a new symbol for port drivers
to use to register cable operations to their registered port alt modes.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240108191620.987785-15-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some USB controller drivers call otg_set_vbus when entering host or
device mode. Implement this callback so that VBUS can be turned on and
off automatically. This is especially useful when there is no property
for a VBUS supply in the controller's binding.
This results in a change in semantics of the vbus_draw regulator.
Whereas before it represented the VBUS supplied by an A-Device when we
acted as a B-Device, now it represents an internal VBUS source.
Accordingly, we no longer set the current limit or enable/disable the
bus from nop_gpio_vbus_thread. Because this supply was never initialized
before the previous commit, there should be no change in behavior.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240123225111.1629405-4-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While support for working with a vbus was added, the regulator was never
actually gotten (despite what was documented). Fix this by actually
getting the supply from the device tree.
Fixes: 7acc9973e3 ("usb: phy: generic: add vbus support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20240123225111.1629405-3-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vbus-regulator property was never actually read from the device tree.
Introduce a new property vbus-supply to represent the regulator powering
the VBUS when acting as an A-Device. This supply will be enabled and
disabled as necessary. Note that this is different from vbus-regulator,
which represented the available current available to draw from VBUS in
B-Device mode. Because no one was using vbus-regulator, remove it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240123225111.1629405-2-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the ip-sleep wakeup functionality on the three MTU3
controllers found on the MT8195 SoC.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20240122111809.148546-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Of the four USB controllers present on the MediaTek MT8195 SoC, three
of them (0, 2 and 3) are behind MTU3: add wakeup controls for them.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20240122111809.148546-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"usb-phy" has multiple type definitions. Unify the type with the looser
definition, phandle-array, as there are cases with multiple entries
(USB2 and USB3). However, the 'phandle-array' type alone is a bit
ambiguous. It can be either just an array of phandles or an array of
phandles plus args. "usb-phy" is the former and needs to constrain each
entry to a single phandle value.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240124190725.1554080-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several bindings implement parts of Type-C USB orientation and mode
switching, and retiming. Keep definition of such properties in one
place, new usb-switch schema, to avoid duplicate defines.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240122094406.32198-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Realtek SoC, the parameter of usb phy is designed to can dynamic
tuning base on port status. Therefore, add a notify callback of generic
phy driver when usb device connect and disconnect change.
The Realtek phy driver is designed to dynamically adjust disconnection
level and calibrate phy parameters. When the device connected bit changes
and when the disconnected bit changes, do connection change notification:
Check if portstatus is USB_PORT_STAT_CONNECTION and portchange is
USB_PORT_STAT_C_CONNECTION.
1. The device is connected, the driver lowers the disconnection level and
calibrates the phy parameters.
2. The device disconnects, the driver increases the disconnect level and
calibrates the phy parameters.
Generic phy driver in usb core framework does not support device connect
and disconnect notifications. Therefore, we add an api to notify phy
the connection changes.
Additionally, the generic phy only specifies primary_hcd in the original
design. Added specific "usb2-phy" on primary_hcd and "usb3-phy" on
shared_hcd.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20231213031203.4911-4-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller. Added the driver to drive the USB 3.0 PHY transceivers.
Note: New driver, remove the port status notification on legacy USB PHY.
Use the generic PHY to notify the usb device connect and disconnect.
To avoid using these PHYs would require describing the very same
PHY using both the generic "phy" property and the deprecated "usb-phy"
property.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20231213031203.4911-3-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Realtek DHC (digital home center) RTD SoCs support DWC3 XHCI USB
controller. Added the driver to drive the USB 2.0 PHY transceivers.
Note: New driver,remove the port status notification on legacy USB PHY.
Use the generic PHY to notify the usb device connect and disconnect.
To avoid using these PHYs would require describing the very same
PHY using both the generic "phy" property and the deprecated "usb-phy"
property.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20231213031203.4911-2-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Realtek SoC, the parameter of usb phy is designed to be able to
do dynamic tuning based in the port status. Therefore, add a notify
callback of phy driver when usb connection/disconnection change.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20231213031203.4911-1-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the default USB device authorization mode configurable at build
time. This is useful for systems that require a mode that is stricter
than the standard setting, as it avoids relying on the kernel command
line being properly set.
Signed-off-by: Niko Mauno <niko.mauno@vaisala.com>
Link: https://lore.kernel.org/r/20240105114956.30714-2-niko.mauno@vaisala.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the wireless USB implementation has been removed and since the
behavior with authorized_default values -1 and 1 is now effectively
same, change the initial value to latter in order to stop using the
leftover value. The former value can still be passed as a module
parameter to retain backwards compatibility.
Signed-off-by: Niko Mauno <niko.mauno@vaisala.com>
Link: https://lore.kernel.org/r/20240105114956.30714-1-niko.mauno@vaisala.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for ac5 to the EHCI Orion platform driver.
The ac5 SOC has DDR starting at offset 0x2_0000_0000,
Hence it requires a larger than 32-bit DMA mask to operate.
Move the dma mask to be pointed by the OF match data, and
use that match data when initializng the DMA mask.
Signed-off-by: Elad Nachman <enachman@marvell.com>
Link: https://lore.kernel.org/r/20240114172154.2622275-3-enachman@marvell.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the Cypress CCGx Type-C controller the following error is
sometimes observed on boot:
[ 16.087147] ucsi_ccg 1-0008: failed to reset PPM!
[ 16.087319] ucsi_ccg 1-0008: PPM init failed (-110)
When the above timeout occurs the following happens:
1. The function ucsi_reset_ppm() is called to reset UCSI controller.
This function performs an async write to start reset and then
polls for completion.
2. An interrupt occurs when the reset completes. In the interrupt
handler, the OPM field in the INTR_REG is cleared and this clears
the CCI data in the PPM. Hence, the reset completion status is
cleared.
3. The function ucsi_reset_ppm() continues to poll for the reset
completion, but has missed the reset completion event and
eventually timeouts.
In this patch, we store CCI when handling the interrupt and make
reading after async write gets the correct value.
To align with the CCGx UCSI interface guide, this patch updates the
driver to copy CCI and MESSAGE_IN before they are reset when UCSI
interrupt acknowledged.
When a new command is sent, the driver will clear the old CCI to avoid
ucsi_ccg_read() getting wrong CCI after ucsi_ccg_async_write() when
the UCSI interrupt is not handled.
Finally, acking the UCSI_READ_INT interrupt before calling complete()
in ISR to ensure that the ucsi_ccg_sync_write() would wait for the
interrupt handling to complete.
Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240126030115.3791554-1-haotienh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is likely a copy-paste error. Replace "Source" with "Selector" where
appropriate.
Fixes: 7e84789403 ("linux/usb/audio.h: split header")
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Link: https://lore.kernel.org/r/20240125211635.30140-1-alexander@tsoy.me
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial ports did not have their interconnect paths specified when
they were first introduced. Fix that.
Fixes: 5188049c9b ("arm64: dts: qcom: Add base SM8450 DTSI")
Fixes: f583741847 ("arm64: dts: qcom: sm8450: add uart20 node")
Reported-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Suggested-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240116-topic-8450serial-v1-1-b685e6a5ad78@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use of_reset_control_array_get_optional_exclusive() instead, it is
implemented as:
static inline struct reset_control *
of_reset_control_array_get_optional_exclusive(struct device_node *node)
{
return of_reset_control_array_get(node, false, true, true);
}
This makes the code easier to understand and removes the last remaining
direct use of of_reset_control_array_get(). No functional changes.
This change was made possible by commit f4cc91ddd8 ("usb: dwc3:
of-simple: remove Amlogic GXL and AXG compatibles"), which made the
parameters passed to of_reset_control_array_get() constant.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20240125-dwc3-of-simple-reset-control-array-fix-v2-1-1ab6b52cad21@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ITE IT5202 is a USB Type-C Alternate Mode Passive MUX, used for
muxing the SBU lines of a Type-C port with DisplayPort altmode and
also providing an orientation switch.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240122110446.140226-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a binding for the ITE IT5205 Alternate Mode Passive MUX,
used for connecting, disconnecting and switching orientation and
control the SBU signals for alternate modes on USB Type-C ports.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240122110446.140226-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In sddr55_{read|write}_data(), the address variables are needlessly typed
as *unsigned long* -- which is 32-bit type on the 32-bit arches and 64-bit
type on the 64-bit arches; those variables' value should fit into just 3
command bytes and consists of 10-bit block # (or at least the max block #
seems to be 1023) and 4-/5-bit page # within a block, so 32-bit *unsigned*
*int* type should be more than enough...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
[Sergey: rewrote the patch subject/description]
Signed-off-by: Karina Yankevich <k.yankevich@omp.ru>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/4c9485f2-0bfc-591b-bfe7-2059289b554e@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PM core now gives us a primitive that does not touch
the counter in an error case. Use it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240118202300.1616-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When write UDC to empty and unbind gadget driver from gadget device, it is
possible that there are many queue failures for mass storage function.
The root cause is mass storage main thread alaways try to queue request to
receive a command from host if running flag is on, on platform like dwc3,
if pull down called, it will not queue request again and return
-ESHUTDOWN, but it not affect running flag of mass storage function.
Check return code from mass storage function and clear running flag if it
is -ESHUTDOWN, also indicate start in/out transfer failure to break loops.
Cc: stable <stable@kernel.org>
Signed-off-by: yuan linyu <yuanlinyu@hihonor.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240123034829.3848409-1-yuanlinyu@hihonor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OTG 1.3 spec has the feature A_ALT_HNP_SUPPORT, which tells
a device that it is connected to the wrong port. Some devices
refuse to operate if you enable that feature, because it indicates
to them that they ought to request to be connected to another port.
According to the spec this feature may be used based only the following
three conditions:
6.5.3 a_alt_hnp_support
Setting this feature indicates to the B-device that it is connected to
an A-device port that is not capable of HNP, but that the A-device does
have an alternate port that is capable of HNP.
The A-device is required to set this feature under the following conditions:
• the A-device has multiple receptacles
• the A-device port that connects to the B-device does not support HNP
• the A-device has another port that does support HNP
A check for the third and first condition is missing. Add it.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@kernel.org>
Fixes: 7d2d641c44 ("usb: otg: don't set a_alt_hnp_support feature for OTG 2.0 device")
Link: https://lore.kernel.org/r/20240122153545.12284-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When power is recycled in usb controller during system power management,
the controller will recognize it and switch role if role has been changed
during power lost. In current design, it will be completed in resume()
function. However, this may bring issues since usb class devices have
their pm operations too and these device's resume() functions are still
not being called at this point. When usb controller recognized host role
should be stopped, these usb class devices will be removed at this point.
But these usb class devices can't be removed in some cases, such as scsi
devices. Since scsi driver may sync data to U-disk, however it will block
there because scsi drvier can only handle pm request when is in suspended
state. Therefore, there may exist a dependency between ci_resume() and usb
class device's resume(). To break this potential dependency, we need to
handle power lost work in a workqueue.
Fixes: 74494b3321 ("usb: chipidea: core: add controller resume support when controller is powered off")
cc: stable@vger.kernel.org
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240119123537.3614838-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current scenario if Plug-out and Plug-In performed continuously
there could be a chance while checking for dwc->gadget_driver in
dwc3_gadget_suspend, a NULL pointer dereference may occur.
Call Stack:
CPU1: CPU2:
gadget_unbind_driver dwc3_suspend_common
dwc3_gadget_stop dwc3_gadget_suspend
dwc3_disconnect_gadget
CPU1 basically clears the variable and CPU2 checks the variable.
Consider CPU1 is running and right before gadget_driver is cleared
and in parallel CPU2 executes dwc3_gadget_suspend where it finds
dwc->gadget_driver which is not NULL and resumes execution and then
CPU1 completes execution. CPU2 executes dwc3_disconnect_gadget where
it checks dwc->gadget_driver is already NULL because of which the
NULL pointer deference occur.
Cc: stable@vger.kernel.org
Fixes: 9772b47a4c ("usb: dwc3: gadget: Fix suspend/resume during device mode")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Uttkarsh Aggarwal <quic_uaggarwa@quicinc.com>
Link: https://lore.kernel.org/r/20240119094825.26530-1-quic_uaggarwa@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the function update_port_device_state gets the usb_hub from
udev->parent by calling usb_hub_to_struct_hub.
However, in case the actconfig or the maxchild is 0, the usb_hub would
be NULL and upon further accessing to get port_dev would result in null
pointer dereference.
Fix this by introducing an if check after the usb_hub is populated.
Fixes: 83cb2604f6 ("usb: core: add sysfs entry for usb device state")
Cc: stable@vger.kernel.org
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20240110095814.7626-1-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Regular expression used to match the unit address part should not allow
non-hex numbers.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240123083511.21063-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
xHCI 4.9 explicitly forbids assuming that the xHC has released its
ownership of a multi-TRB TD when it reports an error on one of the
early TRBs. Yet the driver makes such assumption and releases the TD,
allowing the remaining TRBs to be freed or overwritten by new TDs.
The xHC should also report completion of the final TRB due to its IOC
flag being set by us, regardless of prior errors. This event cannot
be recognized if the TD has already been freed earlier, resulting in
"Transfer event TRB DMA ptr not part of current TD" error message.
Fix this by reusing the logic for processing isoc Transaction Errors.
This also handles hosts which fail to report the final completion.
Fix transfer length reporting on Babble errors. They may be caused by
device malfunction, no guarantee that the buffer has been filled.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last TRB of a isoc TD might not trigger an event if there was
an error event for a TRB mid TD. This is seen on a NEC Corporation
uPD720200 USB 3.0 Host
After an error mid a multi-TRB TD the xHC should according to xhci 4.9.1
generate events for passed TRBs with IOC flag set if it proceeds to the
next TD. This event is either a copy of the original error, or a
"success" transfer event.
If that event is missing then the driver and xHC host get out of sync as
the driver is still expecting a transfer event for that first TD, while
xHC host is already sending events for the next TD in the list.
This leads to
"Transfer event TRB DMA ptr not part of current TD" messages.
As a solution we tag the isoc TDs that get error events mid TD.
If an event doesn't match the first TD, then check if the tag is
set, and event points to the next TD.
In that case give back the fist TD and process the next TD normally
Make sure TD status and transferred length stay valid in both cases
with and without final TD completion event.
Reported-by: Michał Pecio <michal.pecio@gmail.com>
Closes: https://lore.kernel.org/linux-usb/20240112235205.1259f60c@foxbook/
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sanity check of interrupter index when adding a new interrupter is
off by one. intr_num needs to be smaller than xhci->max_interrupter to
fit the array of interrupters.
Luckily this doesn't cause any real word harm as xhci_add_interrupter()
is always called with a intr_num value smaller than xhci->max_interrupters
in any current kernel.
Should not be needed for stable as 6.7 kernel and older only supports
one interrupter, with intr_num always being zero.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-usb/e9771296-586d-456a-ac24-a82de79bb2e6@moroto.mountain/
Fixes: 4bf398e15a ("xhci: split allocate interrupter into separate alloacte and add parts")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent commit [1] added support for changing max segment size of the NCM
interface via configfs. But the value of segment size value stored in
ncm_opts need to be converted to little endian before saving it in
ecm_desc. Also while initialising the value of segment size in opts during
instance allocation, the value ETH_FRAME_LEN needs to be assigned directly
without any conversion as ETH_FRAME_LEN and the variable max_segment_size
are native endian. The current implementaion modifies it into little endian
thus breaking things for big endian targets.
Fix endianness while assigning these variables.
While at it, fix up some stray spaces in comments added in code.
[1]: https://lore.kernel.org/all/20231221153216.18657-1-quic_kriskura@quicinc.com/
Fixes: 1900daeefd ("usb: gadget: ncm: Add support to update wMaxSegmentSize via configfs")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240118154910.8765-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upstream commit bac1ec5514 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. Currently this quirk can only be set using
xhci private data. But there are some drivers like dwc3/host.c
which adds adds quirks using software node for xhci device.
Hence set this xhci quirk by iterating over device properties.
Cc: stable@vger.kernel.org # 5.11
Fixes: bac1ec5514 ("usb: xhci: Set quirk for XHCI_SG_TRB_CACHE_SIZE_QUIRK")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-3-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upstream commit bac1ec5514 ("usb: xhci: Set quirk for
XHCI_SG_TRB_CACHE_SIZE_QUIRK") introduced a new quirk in XHCI
which fixes XHC timeout, which was seen on synopsys XHCs while
using SG buffers. But the support for this quirk isn't present
in the DWC3 layer.
We will encounter this XHCI timeout/hung issue if we run iperf
loopback tests using RTL8156 ethernet adaptor on DWC3 targets
with scatter-gather enabled. This gets resolved after enabling
the XHCI_SG_TRB_CACHE_SIZE_QUIRK. This patch enables it using
the xhci device property since its needed for DWC3 controller.
In Synopsys DWC3 databook,
Table 9-3: xHCI Debug Capability Limitations
Chained TRBs greater than TRB cache size: The debug capability
driver must not create a multi-TRB TD that describes smaller
than a 1K packet that spreads across 8 or more TRBs on either
the IN TR or the OUT TR.
Cc: stable@vger.kernel.org #5.11
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240116055816.1169821-2-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the purpose specific devm_kcalloc() function instead of the
argument size * count in the devm_kzalloc() function.
Link: https://www.kernel.org/doc/html/next/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments [1]
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Erick Archer <erick.archer@gmx.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20240119181909.7079-1-erick.archer@gmx.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add new emmc groups in the pinctrl driver for the
MediaTek MT7981 SoC:
* emmc reset, with pin 15.
* emmc 4-bit bus-width, with pins 16 to 19, and 24 to 25.
* emmc 8-bit bus-width, with pins 16 to 25.
The existing emmc_45 group is kept for legacy reasons, even
if this is the union of emmc_reset and emmc_8 groups.
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240117145547.3354242-1-jean.thomas@wifirst.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add uart1_3 (pins 26, 27) group to the pinctrl driver for the
MediaTek MT7981 SoC.
Signed-off-by: Jean Thomas <jean.thomas@wifirst.fr>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240117124234.3137050-1-jean.thomas@wifirst.fr
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix kernel-doc warnings for enum (anonymous): the enum values are not
documented, so don't indicate that the comment contains kernel-doc
notation.
pinctrl-mt7986.c:68: warning: Enum value 'GPIO_BASE' not described in enum '(anonymous)'
pinctrl-mt7986.c:68: warning: Enum value 'IOCFG_RT_BASE' not described in enum '(anonymous)'
pinctrl-mt7986.c:68: warning: Enum value 'IOCFG_RB_BASE' not described in enum '(anonymous)'
pinctrl-mt7986.c:68: warning: Enum value 'IOCFG_LT_BASE' not described in enum '(anonymous)'
pinctrl-mt7986.c:68: warning: Enum value 'IOCFG_LB_BASE' not described in enum '(anonymous)'
pinctrl-mt7986.c:68: warning: Enum value 'IOCFG_TR_BASE' not described in enum '(anonymous)'
pinctrl-mt7986.c:68: warning: Enum value 'IOCFG_TL_BASE' not described in enum '(anonymous)'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312110210.x3vxq42A-lkp@intel.com/
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: <linux-gpio@vger.kernel.org>
Cc: Sean Wang <sean.wang@kernel.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: <linux-mediatek@lists.infradead.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Link: https://lore.kernel.org/r/20240111045126.13768-1-rdunlap@infradead.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
