Chips in this family only have one set of histogram counters, which
can be used to count ingressing and/or egressing traffic. mv88e6xxx
has, up until this point, kept the hardware default of counting both
directions.
In the mean time, standard counter group support has been added to
ethtool. Via that interface, drivers may report ingress-only and
egress-only histograms separately - but not combined.
In order for mv88e6xxx to maximize amount of diagnostic information
that can be exported via standard interfaces, we opt to limit the
histogram counters to ingress traffic only. Which will allow us to
export them via the standard "rmon" group in an upcoming commit.
The reason for choosing ingress-only over egress-only, is to be
compatible with RFC2819 (RMON MIB).
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the applicable subset of an mv88e6xxx port's counters using
ethtool's standardized "eth-mac" counter group.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the upcoming standard counter group support, we are no longer
reading out the whole set of counters, but rather mapping a subset to
the requested group.
Therefore, create an enum with an ID for each stat, such that
mv88e6xxx_hw_stats[] can be subscripted with a human-readable ID
corresponding to the counter's name.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_get_stats, which collects stats from various sources,
expects all callees to return the number of stats read. If an error
occurs, 0 should be returned.
Prevent future mishaps of this kind by updating the return type to
reflect this contract.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change contains no functional change. We simply push the hardware
specific stats logic to a function reading a single counter, rather
than the whole set.
This is a preparatory change for the upcoming standard ethtool
statistics support (i.e. "eth-mac", "eth-ctrl" etc.).
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is more consistent with the driver's general structure.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
net: optmem_max changes
optmem_max default value is too small for tx zerocopy workloads.
First patch increases default from 20KB to 128 KB,
which is the value we have used for seven years.
Second patch makes optmem_max sysctl per netns.
Last patch tweaks two tests accordingly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/sys/net/core/optmem_max is now per netns, change two tests
that were saving/changing/restoring its value on the parent netns.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
optmem_max being used in tx zerocopy,
we want to be able to control it on a netns basis.
Following patch changes two tests.
Tested:
oqq130:~# cat /proc/sys/net/core/optmem_max
131072
oqq130:~# echo 1000000 >/proc/sys/net/core/optmem_max
oqq130:~# cat /proc/sys/net/core/optmem_max
1000000
oqq130:~# unshare -n
oqq130:~# cat /proc/sys/net/core/optmem_max
131072
oqq130:~# exit
logout
oqq130:~# cat /proc/sys/net/core/optmem_max
1000000
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For many years, /proc/sys/net/core/optmem_max default value
on a 64bit kernel has been 20 KB.
Regular usage of TCP tx zerocopy needs a bit more.
Google has used 128KB as the default value for 7 years without
any problem.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the error path of pci_epf_mhi_edma_write() function, the DMA data
direction passed (DMA_FROM_DEVICE) doesn't match the actual direction used
for the data transfer. Fix it by passing the correct one (DMA_TO_DEVICE).
Fixes: 7b99aaadda ("PCI: epf-mhi: Add eDMA support")
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20231214063328.40657-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Petr Machata says:
====================
mlxsw: CFF flood mode: NVE underlay configuration
Recently, support for CFF flood mode (for Compressed FID Flooding) was
added to the mlxsw driver. The most recent patchset has a detailed coverage
of what CFF is and what has changed and how:
https://lore.kernel.org/netdev/cover.1701183891.git.petrm@nvidia.com/
In CFF flood mode, each FID allocates a handful (in our implementation two
or three) consecutive PGT entries. One entry holds the flood vector for
unknown-UC traffic, one for MC, one for BC.
To determine how to look up flood vectors, the CFF flood mode uses a
concept of flood profiles, which are IDs that reference mappings from
traffic types to offsets. In the case of CFF flood mode, the offset in
question is applied to the PGT address configured at a FID. The same
mechanism is used by NVE underlay for flooding. Again the profile ID and
the traffic type determine the offset to apply, this time to KVD address
used to look up flooding entries. Since mlxsw configures NVE underlay flood
the same regardless of traffic type, only one offset was ever needed: the
zero, which is the default, and thus no explicit configuration was needed.
Now that CFF uses profiles as well, it would be better to configure the
profile used by NVE explicitly, to make the configuration visible in the
source code.
In this patchset, add the register support (in patch #1), add a new traffic
type to refer to "any traffic at all" (in patch #2) and finally configure
the NVE profile explicitly for FIDs (in patch #3).
So far, the implicitly configured flood profile was the ID 0. With this
patchset, it changes to 3, leaving the 0 free to allow us to spot missed
configuration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The NVE flood profile is used for determining of offset applied to KVD
address for NVE flood. We currently do not set it, leaving it at the
default value of 0. That is not an issue: all the traffic-type-to-offset
mappings (as configured by SFFP) default to offset of 0. This is what we
need anyway, as mlxsw only allocates a single KVD entry for NVE underlay.
The field is only relevant on Spectrum-2 and above. So to be fully
consistent, we should split the existing controlled ops to Spectrum-1 and
Spectrum>1 variants, with only the latter setting the field. But that seems
like a lot of overhead for a single field whose meaning is "everything is
the default". So instead pretend that the NVE flood profile does not exist
in the controlled flood mode, like we have so far, and only set it when
flood mode is CFF.
Setting this at all serves dual purpose. First, it is now clear which
profile belongs to NVE, because in the CFF mode, we have multiple users.
This should prevent bugs in flood profile management. Second, using
specifically non-zero value means there will be no valid uses of the
profile 0, which we can therefore use as a sentinel.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flood profiles have been used prior to CFF support for NVE underlay. Like
is the case with FID flooding, an NVE profile describes at which offset a
datum is located given traffic type. mlxsw currently only ever uses one KVD
entry for NVE lookup, i.e. regardless of traffic type, the offset is always
zero. To be able to describe this, add a traffic type enumerator describing
"any traffic type".
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The field is used for setting a flood profile for lookup of KVD entry for
NVE underlay. As the other uses of flood profile, this references a traffic
type-to-offset mapping, except here it is not applied to PGT offsets, but
KVD offsets.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the error handling of 'offset > adapter->ring_size', the
tx_ring->tx_buffer allocated by kzalloc should be freed,
instead of 'goto failed' instantly.
Fixes: a6a5325239 ("atl1e: Atheros L1E Gigabit Ethernet driver")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following NULL pointer dereference issue occurred:
BUG: kernel NULL pointer dereference, address: 0000000000000000
<...>
RIP: 0010:ccid_hc_tx_send_packet net/dccp/ccid.h:166 [inline]
RIP: 0010:dccp_write_xmit+0x49/0x140 net/dccp/output.c:356
<...>
Call Trace:
<TASK>
dccp_sendmsg+0x642/0x7e0 net/dccp/proto.c:801
inet_sendmsg+0x63/0x90 net/ipv4/af_inet.c:846
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0x83/0xe0 net/socket.c:745
____sys_sendmsg+0x443/0x510 net/socket.c:2558
___sys_sendmsg+0xe5/0x150 net/socket.c:2612
__sys_sendmsg+0xa6/0x120 net/socket.c:2641
__do_sys_sendmsg net/socket.c:2650 [inline]
__se_sys_sendmsg net/socket.c:2648 [inline]
__x64_sys_sendmsg+0x45/0x50 net/socket.c:2648
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x43/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b
sk_wait_event() returns an error (-EPIPE) if disconnect() is called on the
socket waiting for the event. However, sk_stream_wait_connect() returns
success, i.e. zero, even if sk_wait_event() returns -EPIPE, so a function
that waits for a connection with sk_stream_wait_connect() may misbehave.
In the case of the above DCCP issue, dccp_sendmsg() is waiting for the
connection. If disconnect() is called in concurrently, the above issue
occurs.
This patch fixes the issue by returning error from sk_stream_wait_connect()
if sk_wait_event() fails.
Fixes: 419ce133ab ("tcp: allow again tcp_disconnect() when threads are waiting")
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reported-by: syzbot+c71bc336c5061153b502@syzkaller.appspotmail.com
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Marangi says:
====================
net: phy: at803x: additional cleanup for qca808x
This small series is a preparation for the big code split. While the
qca808x code is waiting to be reviwed and merged, we can further cleanup
and generalize shared functions between at803x and qca808x.
With these last 2 patch everything is ready to move the driver to a
dedicated directory and split the code by creating a library module
for the few shared functions between the 2 driver.
Eventually at803x can be further cleaned and generalized but everything
will be already self contained and related only to at803x family of PHYs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework read specific status function to be more generic. The function
apply different speed mask based on the PHY ID. Make it more generic by
adding an additional arg to pass the specific speed (ss) mask and use
the provided mask to parse the speed value.
This is needed to permit an easier deatch of qca808x code from the
at803x driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move specific qca808x config_aneg to dedicated function to permit easier
split of qca808x portion from at803x driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arseniy Krasnov says:
====================
send credit update during setting SO_RCVLOWAT
DESCRIPTION
This patchset fixes old problem with hungup of both rx/tx sides and adds
test for it. This happens due to non-default SO_RCVLOWAT value and
deferred credit update in virtio/vsock. Link to previous old patchset:
https://lore.kernel.org/netdev/39b2e9fd-601b-189d-39a9-914e5574524c@sberdevices.ru/
Here is what happens step by step:
TEST
INITIAL CONDITIONS
1) Vsock buffer size is 128KB.
2) Maximum packet size is also 64KB as defined in header (yes it is
hardcoded, just to remind about that value).
3) SO_RCVLOWAT is default, e.g. 1 byte.
STEPS
SENDER RECEIVER
1) sends 128KB + 1 byte in a
single buffer. 128KB will
be sent, but for 1 byte
sender will wait for free
space at peer. Sender goes
to sleep.
2) reads 64KB, credit update not sent
3) sets SO_RCVLOWAT to 64KB + 1
4) poll() -> wait forever, there is
only 64KB available to read.
So in step 4) receiver also goes to sleep, waiting for enough data or
connection shutdown message from the sender. Idea to fix it is that rx
kicks tx side to continue transmission (and may be close connection)
when rx changes number of bytes to be woken up (e.g. SO_RCVLOWAT) and
this value is bigger than number of available bytes to read.
I've added small test for this, but not sure as it uses hardcoded value
for maximum packet length, this value is defined in kernel header and
used to control deferred credit update. And as this is not available to
userspace, I can't control test parameters correctly (if one day this
define will be changed - test may become useless).
Head for this patchset is:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=9bab51bd662be4c3ebb18a28879981d69f3ef15a
Link to v1:
https://lore.kernel.org/netdev/20231108072004.1045669-1-avkrasnov@salutedevices.com/
Link to v2:
https://lore.kernel.org/netdev/20231119204922.2251912-1-avkrasnov@salutedevices.com/
Link to v3:
https://lore.kernel.org/netdev/20231122180510.2297075-1-avkrasnov@salutedevices.com/
Link to v4:
https://lore.kernel.org/netdev/20231129212519.2938875-1-avkrasnov@salutedevices.com/
Link to v5:
https://lore.kernel.org/netdev/20231130130840.253733-1-avkrasnov@salutedevices.com/
Link to v6:
https://lore.kernel.org/netdev/20231205064806.2851305-1-avkrasnov@salutedevices.com/
Link to v7:
https://lore.kernel.org/netdev/20231206211849.2707151-1-avkrasnov@salutedevices.com/
Link to v8:
https://lore.kernel.org/netdev/20231211211658.2904268-1-avkrasnov@salutedevices.com/
Link to v9:
https://lore.kernel.org/netdev/20231214091947.395892-1-avkrasnov@salutedevices.com/
Changelog:
v1 -> v2:
* Patchset rebased and tested on new HEAD of net-next (see hash above).
* New patch is added as 0001 - it removes return from SO_RCVLOWAT set
callback in 'af_vsock.c' when transport callback is set - with that
we can set 'sk_rcvlowat' only once in 'af_vsock.c' and in future do
not copy-paste it to every transport. It was discussed in v1.
* See per-patch changelog after ---.
v2 -> v3:
* See changelog after --- in 0003 only (0001 and 0002 still same).
v3 -> v4:
* Patchset rebased and tested on new HEAD of net-next (see hash above).
* See per-patch changelog after ---.
v4 -> v5:
* Change patchset tag 'RFC' -> 'net-next'.
* See per-patch changelog after ---.
v5 -> v6:
* New patch 0003 which sends credit update during reading bytes from
socket.
* See per-patch changelog after ---.
v6 -> v7:
* Patchset rebased and tested on new HEAD of net-next (see hash above).
* See per-patch changelog after ---.
v7 -> v8:
* See per-patch changelog after ---.
v8 -> v9:
* Patchset rebased and tested on new HEAD of net-next (see hash above).
* Add 'Fixes' tag for the current 0002.
* Reorder patches by moving two fixes first.
v9 -> v10:
* Squash 0002 and 0003 and update commit message in result.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Both tests are almost same, only differs in two 'if' conditions, so
implemented in a single function. Tests check, that credit update
message is sent:
1) During setting SO_RCVLOWAT value of the socket.
2) When number of 'rx_bytes' become smaller than SO_RCVLOWAT value.
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send credit update message when SO_RCVLOWAT is updated and it is bigger
than number of bytes in rx queue. It is needed, because 'poll()' will
wait until number of bytes in rx queue will be not smaller than
O_RCVLOWAT, so kick sender to send more data. Otherwise mutual hungup
for tx/rx is possible: sender waits for free space and receiver is
waiting data in 'poll()'.
Rename 'set_rcvlowat' callback to 'notify_set_rcvlowat' and set
'sk->sk_rcvlowat' only in one place (i.e. 'vsock_set_rcvlowat'), so the
transport doesn't need to do it.
Fixes: b89d882dc9 ("vsock/virtio: reduce credit update messages")
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add one more condition for sending credit update during dequeue from
stream socket: when number of bytes in the rx queue is smaller than
SO_RCVLOWAT value of the socket. This is actual for non-default value
of SO_RCVLOWAT (e.g. not 1) - idea is to "kick" peer to continue data
transmission, because we need at least SO_RCVLOWAT bytes in our rx
queue to wake up user for reading data (in corner case it is also
possible to stuck both tx and rx sides, this is why 'Fixes' is used).
Fixes: b89d882dc9 ("vsock/virtio: reduce credit update messages")
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the RZ/G3S Ethernet pins (P1_0, P7_0) can be configured with
input enable. Enable this functionality for these pins.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-8-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some of the Ethernet pins on RZ/G3S (but also valid for RZ/G2L) need to
have the direction of the IO buffer set as output for Ethernet to work
properly. On RZ/G3S, these pins are P1_0/P7_0, P1_1/P7_1, and can have
the following Ethernet functions: TXC/TX_CLK or TX_CTL/TX_EN.
As the pins supporting output enable are SoC specific, and there is a
limited number of these pins (TXC/TX_CLK and/or TX_CTL/TX_EN), specify
output enable capable port limits in the platform-based configuration
data structure, to ensure proper validation.
The OEN support has been intantiated for RZ/G3S at the moment.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-7-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The GPIO controller available on RZ/G3S (but also on RZ/G2L) supports
setting the power source for Ethernet pins. Based on the interface b/w
the Ethernet controller and the Ethernet PHY, and on board design, a
specific power source needs to be selected. The GPIO controller
supports 1.8V, 2.5V, and 3.3V power source selection for the Ethernet
pins. This can be selected though the ETHx_POC registers (x={0, 1}).
Adjust the driver to support this, and to do proper instantiation for
the RZ/G3S and RZ/G2L SoCs. On RZ/G2L only the get operation has been
tested at the moment.
While at it, as the power registers on RZ/G2L support access sizes of 8
bits, and these registers on RZ/G3S support access sizes of 8/16/32
bits, replace writel()/readl() on these registers with writeb()/readb().
This should allow us to use the same code on both SoCs w/o any issues.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-6-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On RZ/G3S different Ethernet pins need to be configured with different
settings (e.g. power-source needs to be set, RGMII TXC and TX_CTL pins
need output-enable). Adjust the driver to allow specifying pin
configuration for pinmux groups. With this, DT settings like the
following are taken into account by the driver:
eth0_pins: eth0 {
tx_ctl {
pinmux = <RZG2L_PORT_PINMUX(1, 1, 1)>; /* ET0_TX_CTL */
power-source = <1800>;
output-enable;
drive-strength-microamp = <5200>;
};
};
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231207070700.4156557-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fix some indentation issues and fix missing newlines in quoted text
by converting quoted text to code blocks.
Reported-by: Christian Brauner <brauner@kernel.org>
Suggested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Akira Yokosawa <akiyks@gmail.com>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
During PFC configuration failure the code was not handling a graceful
exit. This patch fixes the same and add proper code for a graceful exit.
Fixes: 99c969a83d ("octeontx2-pf: Add egress PFC support")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support IP_PKTINFO on those packets, we need to call
ipv4_pktinfo_prepare.
When sending mrouted/pimd daemons a cache report IGMP msg, it is
unnecessary to set dst on the newly created skb.
It used to be necessary on older versions until
commit d826eb14ec ("ipv4: PKTINFO doesnt need dst reference") which
changed the way IP_PKTINFO struct is been retrieved.
Changes from v1:
1. Undo changes in ipv4_pktinfo_prepare function. use it directly
and copy the control block.
Fixes: d826eb14ec ("ipv4: PKTINFO doesnt need dst reference")
Signed-off-by: Leone Fernando <leone4fernando@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to assign and poll more than one EQ on the same
msix index.
It is achieved by introducing a list of attached EQs in each IRQ context.
It also removes the existing msix_index map that tried to ensure that there
is only one EQ at each msix_index.
This patch exports symbols for creating EQs from other MANA kernel modules.
Signed-off-by: Konstantin Taranov <kotaranov@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While disassociating from a PAN ourselves, let's set the maximum number
of associations temporarily to zero to be sure no new device tries to
associate with us.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/linux-wpan/20231128111655.507479-6-miquel.raynal@bootlin.com
Once associated with any device, we are part of a PAN (with a specific
PAN ID), and we are expected to be present on a particular
channel. Let's avoid confusing other devices by preventing any PAN
ID/channel change once associated.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/linux-wpan/20231128111655.507479-5-miquel.raynal@bootlin.com
It is not very clear in the specification whether simple coordinators
are allowed or not to answer to association requests themselves. As
there is no synchronization mechanism, it is probably best to rely on
the relay feature of these coordinators and avoid processing them in
this case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/linux-wpan/20231128111655.507479-4-miquel.raynal@bootlin.com
ACKs come with the source and destination address empty, this has been
clarified already. But there is something else: if the destination
address is empty but the source address is valid, it may be a way to
reach the PAN coordinator. Either the device receiving this frame is the
PAN coordinator itself and should process what it just received
(PACKET_HOST) or it is not and may, if supported, relay the packet as it
is targeted to another device in the network.
Right now we do not support relaying so the packet should be dropped in
the first place, but the stamping looks more accurate this way.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/linux-wpan/20231128111655.507479-3-miquel.raynal@bootlin.com
Sending a beacon is a way to advertise a PAN, but also ourselves as
coordinator in the PAN. There is only one PAN coordinator in a PAN, this
is the device without parent (not associated itself to an "upper"
coordinator). Instead of blindly saying that we are the PAN coordinator,
let's actually use our internal information to fill this field.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/linux-wpan/20231128111655.507479-2-miquel.raynal@bootlin.com
As per the existing implementation, there exists a race between finding
a multicast/mirror group entry and deleting that entry. The group lock
was taken and released independently by rvu_nix_mcast_find_grp_elem()
function. Which is incorrect and group lock should be taken during the
entire operation of group updation/deletion. This patch fixes the same.
Fixes: 51b2804c19 ("octeontx2-af: Add new mbox to support multicast/mirror offload")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ifconfig ethx up, will set page->refcount larger than 1,
and then ifconfig ethx down, calling __page_frag_cache_drain()
to free pages, it is not compatible with page pool.
So deleting codes which changing page->refcount.
Fixes: 3c47e8ae11 ("net: libwx: Support to receive packets in NAPI")
Signed-off-by: duanqiangwen <duanqiangwen@net-swift.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for mlx5e socket direct feature.
Socket direct will allow multiple PF devices attached to different
NUMA nodes but sharing the same physical port.
The following series is a small refactoring series in preparation
to support socket direct in the following submission.
Highlights:
- Define required device registers and bits related to socket direct
- Flow steering re-arrangements
- Generalize TX objects (TISs) and store them in a common object, will
be useful in the next series for per function object management.
- Decouple raw CQ objects from their parent netdev priv
- Prepare devcom for Socket Direct device group discovery.
Please see the individual patches for more information.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmV6YnQACgkQSD+KveBX
+j48MggAi+iKb6supNWaDkSufLsJu7R56jCJK/mHEl/3586wsoiAx8e7BcAzB2FS
J6xfEJOwC++slNlIubWgEAvH8vv8YHI0K8q4+IUaC19FY3uy9z4GdPAAvzhqUbQ7
D1kWQZ4KIwDb5FbniwHw4V88ZBAGXl5Rhm7Wk/T90B4aG3hyGCeYOlsd0DnWNUae
ea7OkMI1s7QZkJ2HL1KS3xy6WMfrTi8G0TnznP0iLX51FYHciIujp0lfeZZlAJgo
+ovMUl2TTKb0yuKuWBapOz6w7le8VixWp7LbVYyd/wVZ1jBQuScgYHA6EeUKhdb8
9rZ726sSNtMjfebcx85KgkYYNleEKA==
=e11K
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2023-12-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2023-12-13
Preparation for mlx5e socket direct feature.
Socket direct will allow multiple PF devices attached to different
NUMA nodes but sharing the same physical port.
The following series is a small refactoring series in preparation
to support socket direct in the following submission.
Highlights:
- Define required device registers and bits related to socket direct
- Flow steering re-arrangements
- Generalize TX objects (TISs) and store them in a common object, will
be useful in the next series for per function object management.
- Decouple raw CQ objects from their parent netdev priv
- Prepare devcom for Socket Direct device group discovery.
Please see the individual patches for more information.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following cleanup issues:
- Missing instruction queue free on cleanup. This
will lead to memory leak.
- lfs->lfs_num is set to zero before cleanup, which
will lead to improper cleanup.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
