Even though the functions to read/write registers can fail, most of
the places in the r8152 driver that read/write register values don't
check error codes. The lack of error code checking is problematic in
at least two ways.
The first problem is that the r8152 driver often uses code patterns
similar to this:
x = read_register()
x = x | SOME_BIT;
write_register(x);
...with the above pattern, if the read_register() fails and returns
garbage then we'll end up trying to write modified garbage back to the
Realtek adapter. If the write_register() succeeds that's bad. Note
that as of commit f53a7ad189 ("r8152: Set memory to all 0xFFs on
failed reg reads") the "garbage" returned by read_register() will at
least be consistent garbage, but it is still garbage.
It turns out that this problem is very serious. Writing garbage to
some of the hardware registers on the Ethernet adapter can put the
adapter in such a bad state that it needs to be power cycled (fully
unplugged and plugged in again) before it can enumerate again.
The second problem is that the r8152 driver generally has functions
that are long sequences of register writes. Assuming everything will
be OK if a random register write fails in the middle isn't a great
assumption.
One might wonder if the above two problems are real. You could ask if
we would really have a successful write after a failed read. It turns
out that the answer appears to be "yes, this can happen". In fact,
we've seen at least two distinct failure modes where this happens.
On a sc7180-trogdor Chromebook if you drop into kdb for a while and
then resume, you can see:
1. We get a "Tx timeout"
2. The "Tx timeout" queues up a USB reset.
3. In rtl8152_pre_reset() we try to reinit the hardware.
4. The first several (2-9) register accesses fail with a timeout, then
things recover.
The above test case was actually fixed by the patch ("r8152: Increase
USB control msg timeout to 5000ms as per spec") but at least shows
that we really can see successful calls after failed ones.
On a different (AMD) based Chromebook with a particular adapter, we
found that during reboot tests we'd also sometimes get a transitory
failure. In this case we saw -EPIPE being returned sometimes. Retrying
worked, but retrying is not always safe for all register accesses
since reading/writing some registers might have side effects (like
registers that clear on read).
Let's fully lock out all register access if a register access fails.
When we do this, we'll try to queue up a USB reset and try to unlock
register access after the reset. This is slightly tricker than it
sounds since the r8152 driver has an optimized reset sequence that
only works reliably after probe happens. In order to handle this, we
avoid the optimized reset if probe didn't finish. Instead, we simply
retry the probe routine in this case.
When locking out access, we'll use the existing infrastructure that
the driver was using when it detected we were unplugged. This keeps us
from getting stuck in delay loops in some parts of the driver.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever the RTL8152_UNPLUG is set that just tells the driver that all
accesses will fail and we should just immediately bail. A future patch
will use this same concept at a time when the driver hasn't actually
been unplugged but is about to be reset. Rename the flag in
preparation for the future patch.
This is a no-op change and just a search and replace.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the adapter is unplugged while we're looping in r8153b_ups_en() /
r8153c_ups_en() we could end up looping for 10 seconds (20 ms * 500
loops). Add code similar to what's done in other places in the driver
to check for unplug and bail.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the adapter is unplugged while we're looping in
rtl_phy_patch_request() we could end up looping for 10 seconds (2 ms *
5000 loops). Add code similar to what's done in other places in the
driver to check for unplug and bail.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error handling in rtl8152_probe() is missing a call to release
firmware. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error handling in rtl8152_probe() is missing a call to cancel the
hw_phy_work. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: a028a9e003 ("r8152: move the settings of PHY to a work queue")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtl8152_probe() function lacks a call to the chip-specific
unload() routine when it sees an error in probe. Add it in to match
the cleanup code in rtl8152_disconnect().
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the comment next to USB_CTRL_GET_TIMEOUT and
USB_CTRL_SET_TIMEOUT, although sending/receiving control messages is
usually quite fast, the spec allows them to take up to 5 seconds.
Let's increase the timeout in the Realtek driver from 500ms to 5000ms
(using the #defines) to account for this.
This is not just a theoretical change. The need for the longer timeout
was seen in testing. Specifically, if you drop a sc7180-trogdor based
Chromebook into the kdb debugger and then "go" again after sitting in
the debugger for a while, the next USB control message takes a long
time. Out of ~40 tests the slowest USB control message was 4.5
seconds.
While dropping into kdb is not exactly an end-user scenario, the above
is similar to what could happen due to an temporary interrupt storm,
what could happen if there was a host controller (HW or SW) issue, or
what could happen if the Realtek device got into a confused state and
needed time to recover.
This change is fairly critical since the r8152 driver in Linux doesn't
expect register reads/writes (which are backed by USB control
messages) to fail.
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Update for net-next
The first 2 patches are fixes for the recently added hwmon changes.
The next 6 patches are enhancements to support ethtool lanes and
all the proper supported and advertised link modes. Before these
patches, the driver was only supporting the link modes for copper
media.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver code does not accurately report the supported and
advertised link modes. It basically always assumes the media type
is copper for any particular speed. Utilize the recently added link
mode mappings to accurately report fully qualified ethtool link modes for
advertised and supported speeds.
If the media type is known, we will report the supported link modes for
that media only. If the media is not known, we will report all possible
supported link modes. The user can now specify any supported link modes
(including NRZ and PAM4) to advertise for autoneg. It used to only accept
copper NRZ modes.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Barring the BNXT_FW_TO_ETHTOOL speed macros, which will be removed
in the next patch, update code to use the newer API.
No functional change.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor some NRZ/PAM4 link speed related logic into helper functions.
The NRZ and PAM4 link parameters are stored in separate structure fields.
The driver logic has to check whether it is in NRZ or PAM4 mode and
then use the appropriate field.
Refactor this logic into helper functions for better readability.
Reviewed-by: Damodharam Ammepalli <damodharam.ammepalli@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A future patch in this series will change the algorithm used to
determine ethtool speed and media modes. Extract the handling of
the unrelated pause, autoneg modes into an independent function.
Also separate FEC handling out of bnxt_fw_to_ethtool_*_spds().
No functional change.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent kernels support changing the number of link lanes via ethtool.
This is useful for determining the appropriate signal mode to use when
a given link speed can be achieved using different lane configurations.
Accept the ethtool lanes parameter when configuring forced speed. If
there is no lanes parameter, select a default.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure to look up the enum ethtool_link_mode_bit_indices
from link information provided by the firmware. The link speed,
signal mode, and media type returned by firmware will be used to
look up the ethtool link mode.
The immediate benefit is that once the link mode is determined, we can
now use ethtool_params_from_link_mode() to fill the basic ethtool
parameters including the number of lanes. Lanes will be fully
supported in the next patch.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW sends the async event to the driver when the device temperature goes
above or below the threshold values. Only notify hwmon if the
temperature is increasing to the next alert level, not when it is
decreasing.
Cc: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer hwmon_notify_event() to bnxt_sp_task() workqueue because
hwmon_notify_event() can try to acquire a mutex shown in the stack trace
below. Modify bnxt_event_error_report() to return true if we need to
schedule bnxt_sp_task() to notify hwmon.
__schedule+0x68/0x520
hwmon_notify_event+0xe8/0x114
schedule+0x60/0xe0
schedule_preempt_disabled+0x28/0x40
__mutex_lock.constprop.0+0x534/0x550
__mutex_lock_slowpath+0x18/0x20
mutex_lock+0x5c/0x70
kobject_uevent_env+0x2f4/0x3d0
kobject_uevent+0x10/0x20
hwmon_notify_event+0x94/0x114
bnxt_hwmon_notify_event+0x40/0x70 [bnxt_en]
bnxt_event_error_report+0x260/0x290 [bnxt_en]
bnxt_async_event_process.isra.0+0x250/0x850 [bnxt_en]
bnxt_hwrm_handler.isra.0+0xc8/0x120 [bnxt_en]
bnxt_poll_p5+0x150/0x350 [bnxt_en]
__napi_poll+0x3c/0x210
net_rx_action+0x308/0x3b0
__do_softirq+0x120/0x3e0
Cc: Guenter Roeck <linux@roeck-us.net>
Fixes: a19b480145 ("bnxt_en: Event handler for Thermal event")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t4_set_params_timeout() can return -EINVAL if failed, add check
for this.
Signed-off-by: Su Hui <suhui@nfschina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
strncat() usage in adf7242_debugfs_init() is wrong.
The size given to strncat() is the maximum number of bytes that can be
written, excluding the trailing NULL.
Here, the size that is passed, DNAME_INLINE_LEN, does not take into account
the size of "adf7242-" that is already in the array.
In order to fix it, use snprintf() instead.
Fixes: 7302b9d901 ("ieee802154/adf7242: Driver for ADF7242 MAC IEEE802154")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new functions were introduced as global functions when they are
only called from inside the file that defines them and should have
been static:
security/apparmor/lsm.c:658:5: error: no previous prototype for 'apparmor_uring_override_creds' [-Werror=missing-prototypes]
security/apparmor/lsm.c:682:5: error: no previous prototype for 'apparmor_uring_sqpoll' [-Werror=missing-prototypes]
Fixes: c4371d9063 ("apparmor: add io_uring mediation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Clang warns (or errors with CONFIG_WERROR=y):
drivers/infiniband/hw/bnxt_re/main.c:1114:2: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
1114 | default:
| ^
drivers/infiniband/hw/bnxt_re/main.c:1114:2: note: insert 'break;' to avoid fall-through
1114 | default:
| ^
| break;
1 error generated.
Clang is a little more pedantic than GCC, which does not warn when
falling through to a case that is just break or return. Clang's version
is more in line with the kernel's own stance in deprecated.rst, which
states that all switch/case blocks must end in either break,
fallthrough, continue, goto, or return. Add the missing break to silence
the warning.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1950
Fixes: b02fd3f79e ("RDMA/bnxt_re: Report async events and errors")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20231020-bnxt_re-implicit-fallthrough-v1-1-b5c19534a6c9@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
- Fix stale propagated yield_cpu in qspinlocks leading to lockups.
- Fix broken hugepages on some configs due to ARCH_FORCE_MAX_ORDER.
- Fix a spurious warning when copros are in use at exit time.
Thanks to: Nicholas Piggin, Christophe Leroy, Nysal Jan K.A Sachin Sant,
Shrikanth Hegde.
-----BEGIN PGP SIGNATURE-----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=2Sx6
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix stale propagated yield_cpu in qspinlocks leading to lockups
- Fix broken hugepages on some configs due to ARCH_FORCE_MAX_ORDER
- Fix a spurious warning when copros are in use at exit time
Thanks to Nicholas Piggin, Christophe Leroy, Nysal Jan K.A Sachin Sant,
and Shrikanth Hegde.
* tag 'powerpc-6.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/qspinlock: Fix stale propagated yield_cpu
powerpc/64s/radix: Don't warn on copros in radix__tlb_flush()
powerpc/mm: Allow ARCH_FORCE_MAX_ORDER up to 12
Remove a redundant call to amdgpu_ctx_priority_is_valid() from
amdgpu_ctx_priority_permit(), which is called from amdgpu_ctx_init() which is
called from amdgpu_ctx_alloc() which is called from amdgpu_ctx_ioctl(), where
we've called amdgpu_ctx_priority_is_valid() already first thing in the
function.
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20231018010359.30393-1-luben.tuikov@amd.com
l9100 uses KTD2026 LED driver. Add it to the device tree.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231013-bq_leds-v1-2-cc374369fc56@apitzsch.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
l8910 uses KTD2026 LED driver. Add it to the device tree.
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231013-bq_leds-v1-1-cc374369fc56@apitzsch.eu
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable sound and modem for the Samsung A7. The setup is similar to most
MSM8916 devices, i.e.:
- QDSP6 audio
- Earpiece/headphones/microphones via digital/analog codec in
MSM8916/PM8916
- WWAN Internet via BAM-DMUX
except for the same differences as the MSM8916-based Samsung A2015
devices:
- NXP TFA9895 codec for speaker on Quaternary MI2S
- Samsung-specific audio jack detection (not supported yet)
Signed-off-by: "Lin, Meng-Bo" <linmengbo0689@protonmail.com>
[Stephan: Add consistent commit message, minor refactoring]
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-14-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable sound and modem for the Samsung J5 smartphones. The setup is
similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Speaker/earpiece/headphones/microphones via digital/analog codec
in MSM8916/PM8916
- WWAN Internet via BAM-DMUX
except:
- There is no secondary microphone, so a different "model" is used to
differentiate that in the UCM configuration.
- Samsung-specific audio jack detection (not supported yet)
Co-developed-by: Markuss Broks <markuss.broks@gmail.com>
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Signed-off-by: "Lin, Meng-Bo" <linmengbo0689@protonmail.com>
[Stephan: Add consistent commit message]
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-13-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable sound and modem for the Samsung Galaxy Tab A 2015 tablets.
The setup is similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Headphones/microphones via digital/analog codec in
MSM8916/PM8916. Earpiece exists on samsung-gt58 only.
- WWAN Internet via BAM-DMUX
except:
- gt510: Stereo Maxim MAX98357A codecs for speaker on Quaternary MI2S
- gt58: Mono NXP TFA9895 codec for speaker on Quaternary MI2S
- For some reason connected to GPIOs where no hardware I2C
controller is available -> need to use i2c-gpio
- Samsung-specific audio jack detection (not supported yet)
Signed-off-by: Jasper Korten <jja2000@gmail.com>
Co-developed-by: Siddharth Manthan <siddharth.manthan@gmail.com>
Signed-off-by: Siddharth Manthan <siddharth.manthan@gmail.com>
Co-developed-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
[Stephan: Add consistent commit message, minor refactoring]
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-12-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable sound and modem for the Longcheer L8910 (BQ Aquaris X5).
The setup is similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Earpiece/headphones/microphones via digital/analog codec in
MSM8916/PM8916
- Audio jack detection via analog codec in PM8916
- WWAN Internet via BAM-DMUX
except:
- Awinic AW8738 connected to HPH_R (headphones) output of the analog
codec. Note that unlike for wingtech-wt88047 there is no analog
switch that would allow disabling output via the headphone jack
when the speaker is enabled.
Signed-off-by: Jonathan Albrieux <jonathan.albrieux@gmail.com>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-11-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Some mmcc clocks have dsi0pll & dsi0pllbyte as clock parents so we
should provide them in the dt, which I missed in the commit adding the
mdss nodes.
Fixes: d5fb01ad5e ("ARM: dts: qcom: msm8226: Add mdss nodes")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230712-msm8226-dsi-clock-fixup-v1-1-71010b0b89ca@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Some nodes weren't sorted by reg, so fix that now. Now all nodes inside
/soc should be sorted correctly.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230627-msm8974-sort-v1-2-75c5800a2e09@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The clocks definition in the interconnect nodes should use tabs (+ 1
space) for indentation instead of 9 spaces. Fix that.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230627-msm8974-sort-v1-1-75c5800a2e09@z3ntu.xyz
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
This commit fixes a bug in commit 9ed9895370 ("driver core: Functional
dependencies tracking support") where the device link status was
incorrectly updated in the driver unbind path before all the device's
resources were released.
Fixes: 9ed9895370 ("driver core: Functional dependencies tracking support")
Cc: stable <stable@kernel.org>
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Closes: https://lore.kernel.org/all/20231014161721.f4iqyroddkcyoefo@pengutronix.de/
Signed-off-by: Saravana Kannan <saravanak@google.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Matti Vaittinen <mazziesaccount@gmail.com>
Cc: James Clark <james.clark@arm.com>
Acked-by: "Rafael J. Wysocki" <rafael@kernel.org>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231018013851.3303928-1-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kzalloc() gives us a zeroed memory, no need to explicitly assing 0 or
NULL or similar to the members of the data structure that has been
allocated with the above mentioned API.
Note, the initializstion of full_list member is not needed anymore
as list_add_tail will rewrite the contents of the prev and next
pointers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231018145948.1367648-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The smatch warns about uncleaned resources in case the
parport_register_port() fails:
parport_register_port() warn: '&tmp->full_list' not removed from list
This is indeed an issue introduced when converting code to use
kasprintf(). However, the whole kasprintf() dance in this case
is not needed as dev_set_name() can handle the formatted input
and produces the same result. So, the solution is to delegate
name forming to the dev_set_name() and make device_register()
error path to deal with error handling (via put_device() call).
Fixes: 8d8ae17eb0 ("parport: Use kasprintf() instead of fixed buffer formatting")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202310180809.hepZB9k6-lkp@intel.com/
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231018145948.1367648-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
chameleon_parse_gdd() may fail for different reasons and end up
in the err tag. Make sure we at least always free the mcb_device
allocated with mcb_alloc_dev().
If mcb_device_register() fails, make sure to give up the reference
in the same place the device was added.
Fixes: 728ac33892 ("mcb: mcb-parse: fix error handing in chameleon_parse_gdd()")
Cc: stable <stable@kernel.org>
Reviewed-by: Jose Javier Rodriguez Barbarin <JoseJavier.Rodriguez@duagon.com>
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Link: https://lore.kernel.org/r/20231019141434.57971-2-jorge.sanjuangarcia@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions mcb_bus_add_devices() and mcb_devices_unregister()
take a mcb_bus as argument that is never being used. This implies
that there is only one bus.
Do not ignore mcb_bus parameter and get the actual bus_type from
the device related to this mcb_bus.
Co-developed-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Signed-off-by: Jose Javier Rodriguez Barbarin <JoseJavier.Rodriguez@duagon.com>
Link: https://lore.kernel.org/r/20231020124324.54692-2-JoseJavier.Rodriguez@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean up comparisons to NULL to improve readability.
Reported by checkpatch.
if (x == NULL) -> if (!x)
if (x != NULL) -> if (x)
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com>
Link: https://lore.kernel.org/r/20231021121947.14516-1-straube.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable sound and modem for the Longcheer L8150 (e.g. Wileyfox Swift).
The setup is similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Speaker/earpiece/headphones/microphones via digital/analog codec
in MSM8916/PM8916
- Audio jack detection via analog codec in PM8916
- WWAN Internet via BAM-DMUX
except:
- The mpss firmware region must be relocated to a different address.
This is because the wcnss firmware is not relocatable for some
reason. The mpss firmware is too large to avoid overlap with wcnss
when placed at the default address (0x86800000).
Surprisingly the vendor kernel does not handle this. The firmware
regions end up overlapping there and somehow this does not explode.
We try to handle this more safely by relocating the mpss region to
the first higher address that is working correctly: 0x8e800000.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-10-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable sound and modem for the ASUS Zenfone 2 Laser. The setup is
similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Speakear/earpiece/headphones/microphones via digital/analog codec
in MSM8916/PM8916
- Audio jack detection via analog codec in PM8916
- WWAN Internet via BAM-DMUX
Signed-off-by: "J.R. Divya Antony" <d.antony.jr@gmail.com>
[Stephan: rebase and simplify, add consistent commit message]
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-9-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable sound and modem for the Alcatel Idol 3 (4.7"). The setup is
similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Microphones via digital/analog codec in MSM8916/PM8916
- WWAN Internet via BAM-DMUX
except:
- Stereo NXP TFA9890 codecs for speakers on Quaternary MI2S
- These are also used as earpieces at the top/bottom.
- Asahi Kasei AK4375 headphone codec on Secondary MI2S
-> Primary MI2S is not used for playback
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
[Stephan: Minor refactoring, add consistent commit message]
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-8-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable sound and modem for the Xiaomi Redmi 2. The setup
is similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Earpiece/headphones/microphones via digital/analog codec in
MSM8916/PM8916
- Audio jack detection via analog codec in PM8916
- WWAN Internet via BAM-DMUX
except:
- Speaker amplifier is connected to HPH_R (headphones) output of the
analog codec. There is a separate analog switch that allows disabling
playback via the headphone jack.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-7-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Enable sound and modem for the Samsung S4 Mini Value Edition. The setup
is similar to most MSM8916 devices, i.e.:
- QDSP6 audio
- Speaker/earpiece/headphones/microphones via digital/analog codec in
MSM8916/PM8916
- WWAN Internet via BAM-DMUX
except:
- Samsung-specific audio jack detection (not supported yet)
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20231003-msm8916-modem-v2-6-61b684be55c0@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
