This patch enables ethtool to set the loopback mode on a given interface.
By configuring the interface in loopback mode in conjunction with a policy
route / rule, a userland application can stress the egress / ingress path
exposing the flows of the change in progress and potentially help developer(s)
understand the impact of those changes without even sending a packet out
on the network.
Following set of commands illustrates one such example -
a) ip -4 addr add 192.168.1.1/24 dev eth1
b) ip -4 rule add from all iif eth1 lookup 250
c) ip -4 route add local 0/0 dev lo proto kernel scope host table 250
d) arp -Ds 192.168.1.100 eth1
e) arp -Ds 192.168.1.200 eth1
f) sysctl -w net.ipv4.ip_nonlocal_bind=1
g) sysctl -w net.ipv4.conf.all.accept_local=1
# Assuming that the machine has 8 cores
h) taskset 000f netserver -L 192.168.1.200
i) taskset 00f0 netperf -t TCP_CRR -L 192.168.1.100 -H 192.168.1.200 -l 30
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP Cubic keeps a metric that estimates the amount of delayed
acknowledgements to use in adjusting the window. If an abnormally
large number of packets are acknowledged at once, then the update
could wrap and reach zero. This kind of ACK could only
happen when there was a large window and huge number of
ACK's were lost.
This patch limits the value of delayed ack ratio. The choice of 32
is just a conservative value since normally it should be range of
1 to 4 packets.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't know why %pI6 doesn't compress, but the format specifier is
kernel-standard, so use it.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB protocol this driver implements appears to require 2 bytes of
padding in front of each received packet. This used to be equal to
the value of NET_IP_ALIGN on x86, so the driver abused that constant
and mostly worked, but this is no longer the case. The driver also
mixed up the URB and packet lengths, resulting in 2 bytes of junk at
the end of the skb.
Introduce a private constant for the 2 bytes of padding; fix this
confusion and check for the under-length case.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NV40 and older cards (pre NV50) reserve a vram bo for the vga memory at
card init. This bo is then freed at card shutdown. The problem is that
the ttm bo vram manager was already freed. So a crash occurs when the
vga bo is freed. The fix is to free the vga bo prior to freeing the ttm
bo vram manager. There might be other solutions but this seemed the
simplest to me.
Signed-off-by: Jimmy Rentz <jb17bsome@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add 20G supported and advertising bit definitions.
20G will be supported with the 57840 chips.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
------
include/linux/ethtool.h | 4 ++++
1 files changed, 4 insertions(+), 0 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to acquire the exact route keying information from the
protocol, however that might be managed.
It handles all of the possibilities, from the simplest case of storing
the key in inet->cork.fl to the more complex setup SCTP has where
individual transports determine the flow.
Signed-off-by: David S. Miller <davem@davemloft.net>
Operation order is now transposed, we first create the child
socket then we try to hook up the route.
Signed-off-by: David S. Miller <davem@davemloft.net>
DESCRIPTION
This patch tries to restore the initial init and cleanup
sequences that was before namspace patch.
Netns also requires action when net devices unregister
which has never been implemented. I.e this patch also
covers when a device moves into a network namespace,
and has to be released.
IMPLEMENTATION
The number of calls to register_pernet_device have been
reduced to one for the ip_vs.ko
Schedulers still have their own calls.
This patch adds a function __ip_vs_service_cleanup()
and an enable flag for the netfilter hooks.
The nf hooks will be enabled when the first service is loaded
and never disabled again, except when a namespace exit starts.
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
[horms@verge.net.au: minor edit to changelog]
Signed-off-by: Simon Horman <horms@verge.net.au>
If the sync daemons run in a name space while it crashes
or get killed, there is no way to stop them except for a reboot.
When all patches are there, ip_vs_core will handle register_pernet_(),
i.e. ip_vs_sync_init() and ip_vs_sync_cleanup() will be removed.
Kernel threads should not increment the use count of a socket.
By calling sk_change_net() after creating a socket this is avoided.
sock_release cant be used intead sk_release_kernel() should be used.
Thanks Eric W Biederman for your advices.
Signed-off-by: Hans Schillstrom <hans@schillstrom.com>
[horms@verge.net.au: minor edit to changelog]
Signed-off-by: Simon Horman <horms@verge.net.au>
This is just like inet_csk_route_req() except that it operates after
we've created the new child socket.
In this way we can use the new socket's cork flow for proper route
key storage.
This will be used by DCCP and TCP child socket creation handling.
Signed-off-by: David S. Miller <davem@davemloft.net>
Several future simplifications are possible now because of this.
For example, the sctp_addr unions can simply refer directly to
the flowi information.
Signed-off-by: David S. Miller <davem@davemloft.net>
All invokers of ip_queue_xmit() must make certain that the
socket is locked. All of SCTP, TCP, DCCP, and L2TP now make
sure this is the case.
Therefore we can use the cork flow during output route lookup in
ip_queue_xmit() when the socket route check fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
These two functions must be invoked only when the socket is locked
(because socket identity modifications are made non-atomically).
Therefore we can use the cork flow for output route lookups.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to make sure that an l2tp socket's inet cork flow is
fully filled in, when it's encapsulated in UDP.
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_xmit_skb() must take the socket lock. It makes use of ip_queue_xmit()
which expects to execute in a socket atomic context.
Since we execute this function in software interrupts, we cannot use the
usual lock_sock()/release_sock() sequence, instead we have to use
bh_lock_sock() and see if a user has the socket locked, and if so drop
the packet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Both l2tp_ip_connect() and l2tp_ip_sendmsg() must take the socket
lock. They both modify socket state non-atomically, and in particular
l2tp_ip_sendmsg() increments socket private counters without using
atomic operations.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since this is invoked from inet_stream_connect() the socket is locked
and therefore this usage is safe.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since this is invoked from inet_stream_connect() the socket is locked
and therefore this usage is safe.
Signed-off-by: David S. Miller <davem@davemloft.net>
After that all the upstream kernel drivers now use phys_id,
and the old ethtool_ops interface (phys_id) can be removed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define POWER_OFF_ON_STANDBY cause trobles when trying to get some
sound from codec because code for bias setup was not compiled
(define wasn't defined). This define was removed in commit:
cc3202f5 but again introduced by commit: f0fba2ad1 which then
completely break codec functionality so remove it again.
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
In function is_bidirectional_neigh the code that find out the one hop
neighbor is duplicated.
Signed-off-by: Daniele Furlan <daniele.furlan@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
It is slightly irritating that comments after a long line span over
multiple lines without any code. It is easier to put them before the
actual code and reduce the number of lines which the eye has to read.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
To be coherent, all the functions/variables/constants have been renamed
to the TranslationTable style
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The hard_if_event is called by the notifier with rtnl_lock and tries to
remove sysfs entries when a NETDEV_UNREGISTER event is received. This
will automatically take the s_active lock.
The s_active lock is also used when a new interface is added to a meshif
through sysfs. In that situation we cannot wait for the rntl_lock before
creating the actual batman-adv interface to prevent a deadlock. It is
still possible to try to get the rtnl_lock and immediately abort the
current operation when the trylock call failed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
hardif_list_lock is unneccessary because we already ensure that no
multiple admin operations can take place through rtnl_lock.
hardif_list_lock only adds additional overhead and complexity.
Critical functions now check whether they are called with rtnl_lock
using ASSERT_RTNL.
It indirectly fixes the problem that orig_hash_del_if() expects that
only one interface is deleted from hardif_list at a time, but
hardif_remove_interfaces() removes all at once and then calls
orig_hash_del_if().
Reported-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The bridge loop detection for batman-adv allows the bat0 interface
to be bridged into an ethernet segment which other batman-adv nodes
are connected to. In order to also allow multiple VLANs on top of
the bat0 interface to be bridged into the ethernet segment this
patch extends the aforementioned bridge loop detection.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Those are leftovers from a pre-multicomponent era.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are currently two controls which allow selecting the capture source, one
as a normal control, the other as part of a DAPM_MUX widget.
Remove the normal control.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Drop unused field from the coeff struct, precalculate the srate register at
compile-time and cleanup up the naming.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
reg_cache_size is supposed to be the number of elements in the register cache,
not the size in bytes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'Mic Boost2' control's shift was off by one and thus was not working.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Annotate the i2c probe and remove functions with __devinit and __devexit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we specifically want to write a block of data to the hw bypassing the
cache, then allow this to happen inside snd_soc_hw_bulk_write_raw().
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows to create DAPM routes depending on those widgets in the
codecs probe function. This is helpful when supporting similar codecs
with minor differences in the DAPM routing with the same driver.
Something similar has already been done for cards in commit
a841ebb9 (ASoC: Create card DAPM widgets early so they can be used in
callbacks).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The RCU callback prl_entry_destroy_rcu() just calls kfree(), so we can
use kfree_rcu() instead of call_rcu().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "Pekka Savola (ipv6)" <pekkas@netcore.fi>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The RCU callback softif_neigh_free_rcu() just calls kfree(), so we can
use kfree_rcu() instead of call_rcu().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Marek Lindner <lindner_marek@yahoo.de>
Cc: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
The RCU callback neigh_node_free_rcu() just calls kfree(), so we can use
kfree_rcu() instead of call_rcu().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Marek Lindner <lindner_marek@yahoo.de>
Cc: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
The RCU callback gw_node_free_rcu() just calls kfree(), so we can use
kfree_rcu() instead of call_rcu().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Marek Lindner <lindner_marek@yahoo.de>
Cc: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
The rcu callback kfree_tid_tx() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(kfree_tid_tx).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
