We have to use cfg->fc_scope not the final nh_scope value.
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "ldo" variable was dereferenced after free on the error path.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently will ignore prefixes when creating DAPM controls. Since currently
all control creation goes through snd_soc_cnew() we can fix this by factoring
the prefixing into that function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Symmetric rate configuration can fail if the second stream starting tries
to apply the symmetric constraint before the first stream has got far
enough to pick a rate. Rather than try to enforce a nonsensical rate of
0Hz log a warning and allow the application to carry on. Things might go
wrong later on but the user will know about it and there's unlikely to be
lasting damage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
When multi component systems use DAIless amplifiers which require clocking
configuration it is at best hard to use the current clocking API as this
requires a DAI even though the device may not even have one. Address this
by adding set_sysclk() and set_pll() operations and APIs for CODECs.
In order to avoid issues with devices which could be used either with or
without DAIs make the DAI variants call through to their CODEC counterparts
if there is no DAI specific operation. Converting over entirely would create
problems for multi-DAI devices which offer per-DAI clocking setup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Annoying as the __devinitdata is actually correct.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Allow a slight simplification of CODEC drivers by allowing DAPM routes and
widgets to be provided in a table. They will be instantiated at the end of
CODEC probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We've found that we still get good, useful isolation at weights this
low. I'd like to adjust the minimum so that any other changes can take
these values into account.
Signed-off-by: Justin TerAvest <teravest@google.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The btrfs fiemap code was incorrectly returning duplicate or overlapping
extents in some cases. cp was blindly trusting this result and we would
end up with a destination file that was bigger than the original because
some bytes were copied twice.
The fix here adjusts our offsets to make sure we're always moving
forward in the fiemap results.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Note that "new" here is not yet fully initialized; auth_domain_put
should be called only on auth_domains that have actually been added to
the hash.
Before this fix, two attempts to add the same domain at once could
cause the hlist_del in auth_domain_put to fail.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
You can crash the kernel (with root/admin privileges) using kprobe tracer by running:
echo "p system_call_after_swapgs" > ./kprobe_events
echo 1 > ./events/kprobes/enable
The reason is that at the system_call_after_swapgs label, the
kernel stack is not set up. If optimized kprobes are enabled,
the user space stack is being used in this case (see optimized
kprobe template) and this might result in a crash.
There are several places like this over the entry code
(entry_$BIT). As it seems there's no any reasonable/maintainable
way to disable only those places where the stack is not ready, I
switched off the whole entry code from kprobe optimizing.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: acme@redhat.com
Cc: fweisbec@gmail.com
Cc: ananth@in.ibm.com
Cc: davem@davemloft.net
Cc: a.p.zijlstra@chello.nl
Cc: eric.dumazet@gmail.com
Cc: 2nddept-manager@sdl.hitachi.co.jp
LKML-Reference: <1298298313-5980-3-git-send-email-jolsa@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Put x86 entry code into a separate link section: .entry.text.
Separating the entry text section seems to have performance
benefits - caused by more efficient instruction cache usage.
Running hackbench with perf stat --repeat showed that the change
compresses the icache footprint. The icache load miss rate went
down by about 15%:
before patch:
19417627 L1-icache-load-misses ( +- 0.147% )
after patch:
16490788 L1-icache-load-misses ( +- 0.180% )
The motivation of the patch was to fix a particular kprobes
bug that relates to the entry text section, the performance
advantage was discovered accidentally.
Whole perf output follows:
- results for current tip tree:
Performance counter stats for './hackbench/hackbench 10' (500 runs):
19417627 L1-icache-load-misses ( +- 0.147% )
2676914223 instructions # 0.497 IPC ( +- 0.079% )
5389516026 cycles ( +- 0.144% )
0.206267711 seconds time elapsed ( +- 0.138% )
- results for current tip tree with the patch applied:
Performance counter stats for './hackbench/hackbench 10' (500 runs):
16490788 L1-icache-load-misses ( +- 0.180% )
2717734941 instructions # 0.502 IPC ( +- 0.079% )
5414756975 cycles ( +- 0.148% )
0.206747566 seconds time elapsed ( +- 0.137% )
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: masami.hiramatsu.pt@hitachi.com
Cc: ananth@in.ibm.com
Cc: davem@davemloft.net
Cc: 2nddept-manager@sdl.hitachi.co.jp
LKML-Reference: <20110307181039.GB15197@jolsa.redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
copy_from_user is pretty high on perf top profile,
replacing it with __copy_from_user helps.
It's also safe because we do access_ok checks during setup.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Minor cleanup of vhost.c and net.c to match coding style.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In complex subsystems like mac80211 structures can contain several
timers and work structs, so identifying a specific instance from the
call trace and object type output of debugobjects can be hard.
Allow the subsystems which support debugobjects to provide a hint
function. This function returns a pointer to a kernel address
(preferrably the objects callback function) which is printed along
with the debugobjects type.
Add hint methods for timer_list, work_struct and hrtimer.
[ tglx: Massaged changelog, made it compile ]
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
LKML-Reference: <20110307085809.GA9334@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently, if a test causes constant output but never reaches a
boot prompt, or crashes, the test will never stop. Add STOP_TEST_AFTER
to create a variable that will stop (and fail) the test after it has run
for this amount of time. The default is 10 minutes. Setting this
variable to -1 will disable it.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Record the console of tests to both the console and the log.
Also, record the bug reports afte the test has completed.
Currently, if a kernel bug happens while running the userland
test, the test stops and will not record the kernel bug. This
makes it difficult to solve what happened.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The config STOP_AFTER_FAILURE is the number of seconds to continue
the test when a failure is detected. This lets the monitor record
more data to the logs and console that may be helpful in solving
the bug that was found.
But the test had a bug. If the failure caused multiple
"Call Trace" stack dumps, the start time to compare the
STOP_AFTER_FAILURE would constantly be reset. Only update the start
time at the first "Call Trace" instance.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add the config option BISECT_FILES that allows the user to
specify what path in the kernel to run the git bisect on.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If a during a git bisect, ktest fails on something other than
what it is testing (if BISECT_TYPE is test but it fails on build),
if BISECT_SKIP is set, then it will do a "git bisect skip" instead
of just failing the bisect and letting the user find a good commit
to test.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
For both git bisect and config bisect, if BISECT_MANUAL is set to 1,
then bisect will stop between iterations and ask the user for the
result. The actual result is ignored. This makes it possible to
use ktest.pl for bisecting configs and git and let the user examine
the results themselves and enter their own results.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When bisecting, one may come across a kernel that does not have
make oldnoconfig. In this case, we need to run the command "yes"
into a make oldconfig. This will select defaults instead of 'n'
into each command, but it works as a work around.
Note, "yes n" will not work because a config may have a value that
"n" is not acceptable for.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Currently we just look for a Call Trace to start the time out
when to reboot the box. But if the kernel panics and does not
show a Call Trace, the test will not reboot the box after
the specified timeout.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
If the test fails and a logfile was specified. Print the name to
let the user know where to look for more information on the
failure.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
net/netfilter/ipset/ip_set_core.c:615: warning: ‘clash’ may be used uninitialized in this function
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This typo was fixed in 46e3f30 (mx25: fix spi device registration typo), but a
the merge at 0e44e059 (Merge commit 'v2.6.37-rc4' into imx-for-2.6.38) resolved
the merge conflict wrongly.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The return value of snd_ctl_hole_check() is used only to detect whether
to continue the loop in snd_ctl_find_hole() or not, so we can simplify
the code by changing this return type to a boolean. Also rename this
function to better show what it actually does.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The purpose of the snd_ctl_hole_check() function is to find conflicts
between the numerical IDs of the new control and those of any existing
controls. However, it would fail to detect an existing control whose
count is smaller than the new control's count and whose interval of IDs
is entirely contained in the interval of the new control's IDs.
To fix this, use the correct formula to detect overlapping intervals,
which happens to simplify the condition.
This problem was not encountered so far because ALSA does not yet allow
drivers to allocate specific control IDs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current AES32 firmware revision ID is 234, however, a user confirmed
that everything works fine with the previous revision, too.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When recovering from unclean reboots UBIFS scans the journal and checks nodes.
If a corrupted node is found, UBIFS tries to check if this is the last node
in the LEB or not. This is is done by checking if there only 0xFF bytes
starting from the next min. I/O unit. However, since now we write in
c->max_write_size, we should actually check for 0xFFs starting from the
next max. write unit.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Switch write-buffers from 'c->min_io_size' to 'c->max_write_size' which
presumably has to be more write speed-efficient. However, when write-buffer
is synchronized, write only the the min. I/O units which contain the
data, do not write whole write-buffer. This is more space-efficient.
Additionally, this patch takes into account that the LEB might not start
from the max. write unit-aligned address.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Currently we assume write-buffer size is always min_io_size. But
this is about to change and write-buffers may be of variable size.
Namely, they will be of max_write_size at the beginning, but will
get smaller when we are approaching the end of LEB.
This is a preparation patch which introduces 'size' field in
the write-buffer structure which carries the current write-buffer
size.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Incorporate the LEB offset information into UBIFS. We'll use this
information in one of the next patches to figure out what are the
max. write size offsets relative to the PEB. So this patch is just
a preparation.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Incorporate maximum write size into the UBIFS description data
structure. This patch just introduces new 'c->max_write_size'
and 'c->max_write_shift' fields as a preparation for the following
patches.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Provide the LEB offset information in the UBI device information data
structure. This piece of information is required by UBIFS to find out
what are the LEB offsets which are aligned to the max. write size.
If LEB offset not aligned to max. write size, then UBIFS has to take
this into account to write more optimally.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Incorporate MTD write buffer size into UBI device information
because UBIFS needs this field. UBI does not use it ATM, just
provides to upper layers in 'struct ubi_device_info'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
