TrimSlice has MicroSD and standard MMC/SD slots.
Register sdhci devices and enable GPIOs for MMC/SD slot.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
The block integrity subsystem no longer uses the bio_vec slabs so this
code can safely be compiled in.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
a) struct inode is not going to be freed under ->d_compare();
however, the thing PROC_I(inode)->sysctl points to just might.
Fortunately, it's enough to make freeing that sucker delayed,
provided that we don't step on its ->unregistering, clear
the pointer to it in PROC_I(inode) before dropping the reference
and check if it's NULL in ->d_compare().
b) I'm not sure that we *can* walk into NULL inode here (we recheck
dentry->seq between verifying that it's still hashed / fetching
dentry->d_inode and passing it to ->d_compare() and there's no
negative hashed dentries in /proc/sys/*), but if we can walk into
that, we really should not have ->d_compare() return 0 on it!
Said that, I really suspect that this check can be simply killed.
Nick?
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This records the number of used blocks per checkpoint in each
checkpoint entry of cpfile. Even though userland tools can get the
block count via nilfs_get_cpinfo ioctl, it was not updated by the
nilfs2 kernel code. This fixes the issue and makes it available for
userland tools to calculate used amount per checkpoint.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Jiro SEKIBA <jir@unicus.jp>
This is a similar change to those in ext2/ext3 codebase (commit
40a063f669 and a4ae309486, respectively).
The addition of 64k block capability in the rec_len_from_disk and
rec_len_to_disk functions added a bit of math overhead which slows
down file create workloads needlessly when the architecture cannot
even support 64k blocks. This will cut the corner.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
At present, the same warning message can be output twice when nilfs
detected a problem on super blocks:
NILFS warning: broken superblock. using spare superblock.
NILFS warning: broken superblock. using spare superblock.
...
This is because these super blocks are reloaded with the block size
written in a super block if it differs from the first block size, but
this repetition looks somewhat confusing. So, we hint at what is
going on by appending block size information to those messages.
Reported-by: Wakko Warner <wakko@animx.eu.org>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
The current FS_IOC_GETFLAGS/SETFLAGS/GETVERSION will fail if
application is 32 bit and kernel is 64 bit.
This issue is avoidable by adding compat_ioctl method.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Add support for the standard attributes set via chattr and read via
lsattr. These attributes are already in the flags value in the nilfs2
inode, but currently we don't have any ioctl commands that expose them
to the userland.
Collaterally, this adds the FS_IOC_GETVERSION ioctl for getting
i_generation, which allows users to list the file's generation number
with "lsattr -v".
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Nilfs has few rectrictions on which flags may be set on which inodes
like ext2/3/4 filesystems used to be. Specifically DIRSYNC may only
be set on directories and IMMUTABLE and APPEND may not be set on
links. Tighten that to disallow TOPDIR being set on non-directories
and only NODUMP and NOATIME to be set on non-regular file,
non-directories.
This introduces a flags masking function like those of extN and uses
it during inode creation.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
At present, nilfs marks S_NOATIME flag on all inodes. This restricts
nilfs_set_inode_flags function so that it marks S_NOATIME only if a
given inode has an FS_NOATIME_FL flag.
Although nilfs does not support atime yet, touch_atime() still safely
returns on IS_NOATIME check since MS_NOATIME is always set on sb.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Replaces uses of own inode flags (i.e. NILFS_SECRM_FL, NILFS_UNRM_FL,
NILFS_COMPR_FL, and so forth) with common inode flags, and removes the
own flag declarations.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Three functions of the current persistent object allocator,
nilfs_palloc_commit_free_entry, nilfs_palloc_abort_alloc_entry, and
nilfs_palloc_freev functions unconditionally add a counter after doing
clear bit operation on a bitmap block.
If the clear bit operation overlapped, the counter will not add up.
This fixes the issue by making the counter operations conditional.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
This fixes the issue that inodes count will not add up after removal
of raw inodes fails. Hence, this prevents possible under flow of the
inodes count.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
When doing output route lookups, we have to select the source address
if the user has not specified an explicit one.
First, if the route has an explicit preferred source address
specified, then we use that.
Otherwise we search the route's outgoing interface for a suitable
address.
This search can be precomputed and cached at route insertion time.
The only missing part is that we have to refresh this precomputed
value any time addresses are added or removed from the interface, and
this is accomplished by fib_update_nh_saddrs().
Signed-off-by: David S. Miller <davem@davemloft.net>
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Update regulator names for debugfs compatiblity on SMDK6410
ARM: S3C64XX: Fix build with WM1190 disabled and WM1192 enabled on SMDK6410
ARM: S3C64XX: Reduce output of s3c64xx_dma_init1()
ARM: S3C64XX: Tone down SDHCI debugging
ARM: S3C64XX: Add clock for i2c1
ARM: S3C64XX: Staticise non-exported GPIO to interrupt functions
ARM: SAMSUNG: Include devs.h in dev-uart.c to prototype devices
ARM: S3C64XX: Fix keypad setup to configure correct number of rows
ARM: S3C2440: Fix usage gpio bank j pin definitions on GTA02
ARM: S5P64X0: Fix number of GPIO lines in Bank F
ARM: S3C2440: Select missing S3C_DEV_USB_HOST on GTA02
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: index i shadowed in 2nd loop
drm/nv50-nvc0: prevent multiple vm/bar flushes occuring simultanenously
drm/nouveau: fix regression causing ttm to not be able to evict vram
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
Add a clockdomain to the GPTIMER7 interface and 2430 HSMMC2 functional
clocks - both were previously missing them.
Also, the 2430 mmchs1_fck is in core_l3_clkdm, but should be in
core_l4_clkdm; fix this.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch fixes these warnings when building kernel for OMAP3EVM
only.
CC arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.o
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:95: warning:
'dsp_24xx_wkdeps' defined but not used
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:119: warning:
'mpu_24xx_wkdeps' defined but not used
arch/arm/mach-omap2/clockdomains2xxx_3xxx_data.c:147: warning:
'core_24xx_wkdeps' defined but not used
The problem should be noticed when building for other OMAP3
platforms (only) as well.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
After commit 81b34fbecb ("OMAP2 clock:
split OMAP2420, OMAP2430 clock data into their own files"), it's
possible to remove dsp_irate_ick from the OMAP2420 and OMAP2430 clock
files. It was originally only needed due to a 2420/2430 clock tree difference,
and now that the data is in separate files, it's superfluous.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the DPLL rate tolerance code that is called during rate
rounding. As far as I know, this code is never used, since it's been
more important for callers of the DPLL round_rate()/set_rate()
functions to obtain an exact rate than it is to save a relatively
small amount of power.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Bail out before we take the clockfw_lock spinlock if the corresponding
OMAP1 or OMAP2+ clock function is not defined. The intention is to
reduce and simplify the work that is done inside the spinlock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The parent of the interface clocks for GPTIMER1, MPU_WDT,
SYNCTIMER_32K, SCM, WDT1, and the ICR (2430 only) were all listed as
being l4_ck. This isn't accurate; these modules exist inside the WKUP
domain, and the interface clock to these modules runs at the SYS_CLK
rate rather than the CORE L4 rate.
So, create a new clock "wu_l4_ick", similar to the OMAP3
"wkup_l4_ick", that serves as the parent for these clocks.
Also, these clocks were listed as existing inside core_l4_clkdm;
wkup_clkdm is probably more accurate.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The OMAP2420/2430 external 32-kHz low-frequency oscillator is a 32768
Hz oscillator, not a 32,000 Hz oscillator[1][2]. Fix this in the clock
tree.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
1. OMAP2420/22 Multimedia Processor Data Manual, Version P [SWPS019P],
section 5.1.4 "External 32-kHz CMOS Clock" (note that it refers to
a "32.768-kHz" clock; this presumably should be "32.768-KHz")
2. OMAP2430 Multimedia Processor ES2.1 Data Manual, Version V [SWPS023V],
section 5.1.4 "External 32-kHz CMOS Clock" (note that it refers to
a "32.768-kHz" clock; this presumably should be "32.768-KHz")
Several clocks are listed as having the core L4 clock as their parent,
when they are actually derived from the L3 clock. Fix these.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
At this point in time, there's no reason for this header file to be in
plat-omap/include/plat/voltage.h. It should not be included by device
drivers, and the code that uses it is currently all under mach-omap2/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There's no reason for this header file to be in
plat-omap/include/plat/smartreflex.h. The hardware devices are in
OMAP2+ SoCs only. Leaving this header file in plat-omap causes
problems due to cross-dependencies with other header files that should
live in mach-omap2/.
Thanks to Benoît Cousson <b-cousson@ti.com> for suggesting the removal
of the smartreflex.h include from the OMAP3xxx hwmod data.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
These CM_AUTOIDLE bits are now set by the clock code via the common PM
code in mach-omap2/pm.c.
N.B.: The pm24xx.c code that this patch removes didn't ensure that the
CM_AUTOIDLE bits were set for several 2430-only modules, such as
GPIO5, MDM_INTC, MMCHS1/2, the modem oscillator clock, and USBHS.
Similarly, the pm34xx.c code that this patch removes didn't ensure
that the CM_AUTOIDLE bits were set for USIM and the AM3517 UART4.
Those cases should now be handled.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
OMAP2430 and OMAP3xxx have modem autoidle bits that are actually
attached to clocks with CM_FCLKEN bits; add the code and data to
handle these.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Mark each interface clock with a corresponding CM_AUTOIDLE bit with
a clkops that has the allow_idle/deny_idle function pointers populated.
This allows the OMAP clock framework to enable and disable autoidle for
these clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add sdrc_ick to the OMAP2420 clock data so the clock code can control
the CM_AUTOIDLE bit associated with this clock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add interface clock type code with autoidle enable/disable support.
The clkops structures created in this file will be used for all
OMAP2/3 interface clocks with autoidle support. They will enable the
clock framework to control interface clock autoidle directly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Place some comments in the OMAP oscillator clock control code to note that
its autoidle mode should eventually be controlled via the new OMAP clockfw
autoidle control interface.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
OMAP2xxx devices have two on-chip APLLs. These APLLs can
automatically enter idle when not in use. Connect the APLL autoidle
code to the clock code, so that the clock framework can handle this
process. As part of this patch, remove the code in mach-omap2/pm24xx.c
that previously handled APLL autoidle control.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Add the necessary code and data to allow the clock framework to enable
and disable the OMAP2 DPLL autoidle state. This is so the direct
register access can be moved out of the mach-omap2/pm24xx.c code, and other
code that needs to control this (e.g., CPUIdle) can do so via an API.
As part of this patch, remove the pm24xx.c code that formerly wrote
directly to the autoidle bits.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Some drivers wish to know whether the device that they control can
ever lose context, for example, when the device's enclosing
powerdomain loses power. They can use this information to determine
whether it is necessary to save and restore device context, or whether
it can be skipped. Implement the powerdomain portion of this by
adding the function pwrdm_can_ever_lose_context(). This is not for
use directly from driver code, but instead is intended to be called
from driver-subarch integration code (i.e., arch/arm/*omap* code).
Currently, the result from this function should be passed into the
driver code via struct platform_data, but at some point this should
be part of some common or OMAP-specific device code.
While here, update file copyrights.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The bank power state bitfields in the powerdomain data are
encoded incorrectly. These fields are intended to be bitfields,
representing a set of power states that the memory banks support.
However, when only one power state was supported by a given bank,
the field was incorrectly set to the bit shift -- not the mask.
While here, update some file copyrights.
The OMAP4 autogeneration scripts have been updated accordingly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Mark the WKUP powerdomain as being always on -- at least, as long as the
chip has power. This will be used to enable the powerdomain code to
determine whether a given powerdomain is ever able to power off. While
here, update the file copyright.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the ability to set 100/F on x540.
Fix reporting of advertised modes by adding check for phy.autoneg_advertised
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use if/then instead of an all-inclusive case statement.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add description for ixgbe_init_eeprom_params_X540 and whitespace fix.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables flow control pause parameters auto-negotiation support
to 82599 based 10G Base-T, backplane devices and multi-speed fiber optics
modules at 1G speed
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
