In ocfs2_dx_dir_rebalance(), we need to rejournal_acess the blocks after
calling ocfs2_insert_extent() since growing an extent tree may trigger
ocfs2_extend_trans(), which makes previous journal_access meaningless.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Track negative dentries by recording the generation number of the parent
directory in d_fsdata. The generation number for the parent directory is
recorded in the inode_info, which increments every time the lock on the
directory is dropped.
If the generation number of the parent directory and the negative dentry
matches, there is no need to perform the revalidate, else a revalidate
is forced. This improves performance in situations where nodes look for
the same non-existent file multiple times.
Thanks Mark for explaining the DLM sequence.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Durring orphan scan, if we are slot 0, and we are replaying
orphan_dir:0001, the general process is that for every file
in this dir:
1. we will iget orphan_dir:0001, since there is no inode for it.
we will have to create an inode and read it from the disk.
2. do the normal work, such as delete_inode and remove it from
the dir if it is allowed.
3. call iput orphan_dir:0001 when we are done. In this case,
since we have no dcache for this inode, i_count will
reach 0, and VFS will have to call clear_inode and in
ocfs2_clear_inode we will checkpoint the inode which will let
ocfs2_cmt and journald begin to work.
4. We loop back to 1 for the next file.
So you see, actually for every deleted file, we have to read the
orphan dir from the disk and checkpoint the journal. It is very
time consuming and cause a lot of journal checkpoint I/O.
A better solution is that we can have another reference for these
inodes in ocfs2_super. So if there is no other race among
nodes(which will let dlmglue to checkpoint the inode), for step 3,
clear_inode won't be called and for step 1, we may only need to
read the inode for the 1st time. This is a big win for us.
So this patch will try to cache system inodes of other slots so
that we will have one more reference for these inodes and avoid
the extra inode read and journal checkpoint.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
generic_check_addressable() erroneously shifts pages down by a block
factor when it should be shifting up. To prevent overflow, we shift
blocks down to pages.
Signed-off-by: Joel Becker <joel.becker@oracle.com>
The OCFS2 developers have already done all of the hard work to allow
volumes larger than 16 TiB. But there is still a "sanity check" in
fs/ocfs2/super.c that prevents the mounting of such volumes, even when
the cluster size and journal options would allow it.
This patch replaces that sanity check with a more sophisticated one to
mount a huge volume provided that (a) it is addressable by the raw
word/address size of the system (borrowing a test from ext4); (b) the
volume is using JBD2; and (c) the JBD2_FEATURE_INCOMPAT_64BIT flag is
set on the journal.
I factored out the sanity check into its own function. I also moved it
from ocfs2_initialize_super() down to ocfs2_check_volume(); any earlier,
and the journal will not have been initialized yet.
This patch is one of a pair, and it depends on the other ("JBD2: Allow
feature checks before journal recovery").
I have tested this patch on small volumes, huge volumes, and huge
volumes without 64-bit block support in the journal. All of them appear
to work or to fail gracefully, as appropriate.
Signed-off-by: Patrick LoPresti <lopresti@gmail.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
We ought to return -ENOENT when non of the registered PMUs
recognise the requested event.
This fixes a boot crash that occurs if no PMU is available
but the NMI watchdog tries to register an event.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Before we start accessing a huge (> 16 TiB) OCFS2 volume, we need to
confirm that its journal supports 64-bit offsets. In particular, we
need to check the journal's feature bits before recovering the journal.
This is not possible with JBD2 at present, because the journal
superblock (where the feature bits reside) is not loaded from disk until
the journal is recovered.
This patch loads the journal superblock in
jbd2_journal_check_used_features() if it has not already been loaded,
allowing us to check the feature bits before journal recovery.
Signed-off-by: Patrick LoPresti <lopresti@gmail.com>
Cc: linux-ext4@vger.kernel.org
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
As part of adding support for OCFS2 to mount huge volumes, we need to
check that the sector_t and page cache of the system are capable of
addressing the entire volume.
An identical check already appears in ext3 and ext4. This patch moves
the addressability check into its own function in fs/libfs.c and
modifies ext3 and ext4 to invoke it.
[Edited to -EINVAL instead of BUG_ON() for bad blocksize_bits -- Joel]
Signed-off-by: Patrick LoPresti <lopresti@gmail.com>
Cc: linux-ext4@vger.kernel.org
Acked-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
ocfs2_sync_inode() is used only from ocfs2_sync_file(). But all data has
already been written before calling ocfs2_sync_file() and ocfs2 doesn't use
inode's private_list for tracking metadata buffers thus sync_mapping_buffers()
is superfluous as well.
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Thanks for the comments. I have incorportated them all.
CONFIG_OCFS2_FS_STATS is enabled and CONFIG_DEBUG_LOCK_ALLOC is disabled.
Statistics now look like -
ocfs2_write_ctxt: 2144 - 2136 = 8
ocfs2_inode_info: 1960 - 1848 = 112
ocfs2_journal: 168 - 160 = 8
ocfs2_lock_res: 336 - 304 = 32
ocfs2_refcount_tree: 512 - 472 = 40
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
In ocfs2, actually we don't allow any direct write pass i_size,
see the function ocfs2_prepare_inode_for_write. So we don't
need the bogus simple_setsize.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Now orphan scan worker has no trace log, so it is
very hard to tell whether it is finished or blocked.
So add 2 mlog trace log so that we can tell whether
the current orphan scan worker is blocked or not.
It does help when I analyzed a orphan scan bug.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
The reason why we need this ioctl is to offer the none-privileged
end-user a possibility to get filesys info gathering.
We use OCFS2_IOC_INFO to manipulate the new ioctl, userspace passes a
structure to kernel containing an array of request pointers and request
count, such as,
* From userspace:
struct ocfs2_info_blocksize oib = {
.ib_req = {
.ir_magic = OCFS2_INFO_MAGIC,
.ir_code = OCFS2_INFO_BLOCKSIZE,
...
}
...
}
struct ocfs2_info_clustersize oic = {
...
}
uint64_t reqs[2] = {(unsigned long)&oib,
(unsigned long)&oic};
struct ocfs2_info info = {
.oi_requests = reqs,
.oi_count = 2,
}
ret = ioctl(fd, OCFS2_IOC_INFO, &info);
* In kernel:
Get the request pointers from *info*, then handle each request one bye one.
Idea here is to make the spearated request small enough to guarantee
a better backward&forward compatibility since a small piece of request
would be less likely to be broken if filesys on raw disk get changed.
Currently, the following 7 requests are supported per the requirement from
userspace tool o2info, and I believe it will grow over time:-)
OCFS2_INFO_CLUSTERSIZE
OCFS2_INFO_BLOCKSIZE
OCFS2_INFO_MAXSLOTS
OCFS2_INFO_LABEL
OCFS2_INFO_UUID
OCFS2_INFO_FS_FEATURES
OCFS2_INFO_JOURNAL_SIZE
This ioctl is only specific to OCFS2.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
The workqueue implementation in 2.6.36-rcX has changed, resulting
in the workqueues no longer having dedicated threads for work
processing. This has caused severe livelocks under heavy parallel
create workloads because the log IO completions have been getting
held up behind metadata IO completions. Hence log commits would
stall, memory allocation would stall because pages could not be
cleaned, and lock contention on the AIL during inode IO completion
processing was being seen to slow everything down even further.
By making the log Io completion workqueue a high priority workqueue,
they are queued ahead of all data/metadata IO completions and
processed before the data/metadata completions. Hence the log never
gets stalled, and operations needed to clean memory can continue as
quickly as possible. This avoids the livelock conditions and allos
the system to keep running under heavy load as per normal.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Fix calculation of "max_pnode" for systems where the the highest
blade has neither cpus or memory. (And, yes, although rare this
does occur).
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20100910150808.GA19802@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
An execve with a very large total of argument/environment strings
can take a really long time in the execve system call. It runs
uninterruptibly to count and copy all the strings. This change
makes it abort the exec quickly if sent a SIGKILL.
Note that this is the conservative change, to interrupt only for
SIGKILL, by using fatal_signal_pending(). It would be perfectly
correct semantics to let any signal interrupt the string-copying in
execve, i.e. use signal_pending() instead of fatal_signal_pending().
We'll save that change for later, since it could have user-visible
consequences, such as having a timer set too quickly make it so that
an execve can never complete, though it always happened to work before.
Signed-off-by: Roland McGrath <roland@redhat.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a preemption point during the copying of the argument and
environment strings for execve, in copy_strings(). There is already
a preemption point in the count() loop, so this doesn't add any new
points in the abstract sense.
When the total argument+environment strings are very large, the time
spent copying them can be much more than a normal user time slice.
So this change improves the interactivity of the rest of the system
when one process is doing an execve with very large arguments.
Signed-off-by: Roland McGrath <roland@redhat.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CONFIG_STACK_GROWSDOWN variant of setup_arg_pages() does not
check the size of the argument/environment area on the stack.
When it is unworkably large, shift_arg_pages() hits its BUG_ON.
This is exploitable with a very large RLIMIT_STACK limit, to
create a crash pretty easily.
Check that the initial stack is not too large to make it possible
to map in any executable. We're not checking that the actual
executable (or intepreter, for binfmt_elf) will fit. So those
mappings might clobber part of the initial stack mapping. But
that is just userland lossage that userland made happen, not a
kernel problem.
Signed-off-by: Roland McGrath <roland@redhat.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch solve compile error when .config doesn't have
CONFIG_SND_SOC which is needed for HDMI sound.
It was reported by Guennadi as follows
Besides, I think, this will not link without CONFIG_SND_SOC.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch solve below report from Guennadi.
But I didn't remove #include <sound/sh_fsi.h>.
Because it have FSI_PORT_B define which is used on this file.
> +#include <linux/platform_device.h>
> +#include <sound/sh_fsi.h>
> +#include <video/sh_mobile_hdmi.h>
Now that everything is done with strings - do you still need these
headers?
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch solve below report from Guennadi
> +static struct snd_soc_dai_driver sh_hdmi_dai = {
> + .name = "sh_mobile_hdmi-hifi",
> + .playback = {
> + .stream_name = "Playback",
> + .channels_min = 1,
Can it actually do mono? Maybe at probe time you could look at audio flags
from your previous patch and, e.g., for SPDIF set channels_min to 2?
> + .channels_max = 2,
That's the "smallest max," yes. With some other interfaces (I2S, DSD) it
can support up to 8 channels...
> + .rates = SNDRV_PCM_RATE_8000_48000,
Hm, in the datasheet I see supported frequencies 32kHz to 192kHz. And if
you promise support for multiple frequencies, don't you want to implement
.hw_params? Besides, not all of these frequencies will be available,
depending on your supplied clock and your willingness to implement
downsampling.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch solve below report from Guennadi
1)
> - hdmi_write(hdmi, 0x00, HDMI_AUDIO_SETTING_1);
> + switch (pdata->flags & HDMI_SRC_MASK) {
> + default:
> + /* FALL THROUGH */
I'm not sure I like the capitalisation here - no reason to shout;)
2)
> +/************************************************************************
> +
> +
> + HDMI sound
> +
> +
> +************************************************************************/
I don't think this comment deserves 7 lines of text, besides breaking the
multiline comment style. If you think, one line like
/* HDMI sound */
is not enough how about just
/*
* HDMI sound
*/
3)
> +/************************************************************************
> +
> +
> + HDMI video
> +
> +
> +************************************************************************/
See above - 7 lines seem to be an overkill to me.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
create_singlethreaded_workqueue() is being phased out for a new
concurrency managed task infrastructure.
Adapt our workqueue constructor to explicitly create a domain that only
allows the execution of a single task at any time. All the tasks are
expected to require the dev->struct_mutex, so would block concurrency of
other tasks if we allow more than a single i915 task to be run at once.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'kvm-updates/2.6.36' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Perform hardware_enable in CPU_STARTING callback
KVM: i8259: fix migration
KVM: fix i8259 oops when no vcpus are online
KVM: x86 emulator: fix regression with cmpxchg8b on i386 hosts
Just got my 6 way machine to a state where cpu 0 is in an
endless loop within __smp_call_function_single.
All other cpus are idle.
The call trace on cpu 0 looks like this:
__smp_call_function_single
scheduler_tick
update_process_times
tick_sched_timer
__run_hrtimer
hrtimer_interrupt
clock_comparator_work
do_extint
ext_int_handler
----> timer irq
cpu_idle
__smp_call_function_single() got called from nohz_balancer_kick()
(inlined) with the remote cpu being 1, wait being 0 and the per
cpu variable remote_sched_softirq_cb (call_single_data) of the
current cpu (0).
Then it loops forever when it tries to grab the lock of the
call_single_data, since it is already locked and enqueued on cpu 0.
My theory how this could have happened: for some reason the
scheduler decided to call __smp_call_function_single() on it's own
cpu, and sends an IPI to itself. The interrupt stays pending
since IRQs are disabled. If then the hypervisor schedules the
cpu away it might happen that upon rescheduling both the IPI and
the timer IRQ are pending. If then interrupts are enabled again
it depends which one gets scheduled first.
If the timer interrupt gets delivered first we end up with the
local deadlock as seen in the calltrace above.
Let's make __smp_call_function_single() check if the target cpu is
the current cpu and execute the function immediately just like
smp_call_function_single does. That should prevent at least the
scenario described here.
It might also be that the scheduler is not supposed to call
__smp_call_function_single with the remote cpu being the current
cpu, but that is a different issue.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Cc: Venkatesh Pallipadi <venki@google.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20100910114729.GB2827@osiris.boeblingen.de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: t_start: reset FTRACE_ITER_HASH in case of seek/pread
perf symbols: Fix multiple initialization of symbol system
perf: Fix CPU hotplug
perf, trace: Fix module leak
tracing/kprobe: Fix handling of C-unlike argument names
tracing/kprobes: Fix handling of argument names
perf probe: Fix handling of arguments names
perf probe: Fix return probe support
tracing/kprobe: Fix a memory leak in error case
tracing: Do not allow llseek to set_ftrace_filter
Fix a bug in keyctl_session_to_parent() whereby it tries to check the ownership
of the parent process's session keyring whether or not the parent has a session
keyring [CVE-2010-2960].
This results in the following oops:
BUG: unable to handle kernel NULL pointer dereference at 00000000000000a0
IP: [<ffffffff811ae4dd>] keyctl_session_to_parent+0x251/0x443
...
Call Trace:
[<ffffffff811ae2f3>] ? keyctl_session_to_parent+0x67/0x443
[<ffffffff8109d286>] ? __do_fault+0x24b/0x3d0
[<ffffffff811af98c>] sys_keyctl+0xb4/0xb8
[<ffffffff81001eab>] system_call_fastpath+0x16/0x1b
if the parent process has no session keyring.
If the system is using pam_keyinit then it mostly protected against this as all
processes derived from a login will have inherited the session keyring created
by pam_keyinit during the log in procedure.
To test this, pam_keyinit calls need to be commented out in /etc/pam.d/.
Reported-by: Tavis Ormandy <taviso@cmpxchg8b.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Tavis Ormandy <taviso@cmpxchg8b.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's an protected access to the parent process's credentials in the middle
of keyctl_session_to_parent(). This results in the following RCU warning:
===================================================
[ INFO: suspicious rcu_dereference_check() usage. ]
---------------------------------------------------
security/keys/keyctl.c:1291 invoked rcu_dereference_check() without protection!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
1 lock held by keyctl-session-/2137:
#0: (tasklist_lock){.+.+..}, at: [<ffffffff811ae2ec>] keyctl_session_to_parent+0x60/0x236
stack backtrace:
Pid: 2137, comm: keyctl-session- Not tainted 2.6.36-rc2-cachefs+ #1
Call Trace:
[<ffffffff8105606a>] lockdep_rcu_dereference+0xaa/0xb3
[<ffffffff811ae379>] keyctl_session_to_parent+0xed/0x236
[<ffffffff811af77e>] sys_keyctl+0xb4/0xb6
[<ffffffff81001eab>] system_call_fastpath+0x16/0x1b
The code should take the RCU read lock to make sure the parents credentials
don't go away, even though it's holding a spinlock and has IRQ disabled.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: Range check cpu in blk_cpu_to_group
scatterlist: prevent invalid free when alloc fails
writeback: Fix lost wake-up shutting down writeback thread
writeback: do not lose wakeup events when forking bdi threads
cciss: fix reporting of max queue depth since init
block: switch s390 tape_block and mg_disk to elevator_change()
block: add function call to switch the IO scheduler from a driver
fs/bio-integrity.c: return -ENOMEM on kmalloc failure
bio-integrity.c: remove dependency on __GFP_NOFAIL
BLOCK: fix bio.bi_rw handling
block: put dev->kobj in blk_register_queue fail path
cciss: handle allocation failure
cfq-iosched: Documentation help for new tunables
cfq-iosched: blktrace print per slice sector stats
cfq-iosched: Implement tunable group_idle
cfq-iosched: Do group share accounting in IOPS when slice_idle=0
cfq-iosched: Do not idle if slice_idle=0
cciss: disable doorbell reset on reset_devices
blkio: Fix return code for mkdir calls
* 'at91-fixes-for-linus' of git://github.com/at91linux/linux-2.6-at91:
AT91: at91sam9261ek: remove C99 comments but keep information
AT91: at91sam9261ek board: remove warnings related to use of SPI or SD/MMC
AT91: dm9000 initialization update
AT91: SAM9G45 - add a separate clock entry for every single TC block
AT91: clock: peripheral clocks can have other parent than mck
AT91: change dma resource index
Even though we call it from the inherit path, where the child is
not yet accessible, we need to hold ctx->lock, add_event_to_ctx()
assumes IRQs are disabled.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: rawmidi: fix the get next midi device ioctl
ALSA: hda - Fix wrong HP pin detection in snd_hda_parse_pin_def_config()
ALSA: seq/oss - Fix double-free at error path of snd_seq_oss_open()
ALSA: msnd-classic: Fix invalid cfg parameter
ALSA: hda - Enable PC-beep for EeePC with ALC269 codec
ALSA: hda - Add errata initverb sequence for CS42xx codecs
ALSA: usb - Release capture substream URBs properly
ALSA: virtuoso: fix setting of Xonar DS line-in/mic-in controls
ALSA: virtuoso: work around missing reset in the Xonar DS Windows driver
ALSA: hda - Add quirk for Lenovo T400s
ALSA: usb-audio: fix detection of vendor-specific device protocol settings
ALSA: usb-audio: Assume first control interface is for audio
ALSA: hda - Add a new hp-laptop model for Conexant 5066, tested on HP G60
We don't know how to enable it safely, especially as outputs turn on and
off. When disabling LP1 we also need to make sure LP2 and 3 are already
disabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29173
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29082
Reported-by: Chris Lord <chris@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The XFS_IOC_FSGETXATTR ioctl allows unprivileged users to read 12
bytes of uninitialized stack memory, because the fsxattr struct
declared on the stack in xfs_ioc_fsgetxattr() does not alter (or zero)
the 12-byte fsx_pad member before copying it back to the user. This
patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
The PCM controller platform devices are registered by the
name 'samsung-pcm', so use the same in the CPU driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Drop the invalid -dai suffix appended to the Samsung AC97 CPU DAI.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current SND_FSI_xxx menu attributes were bool,
but it should be tristate.
This patch solve below report from Guennadi
"bool" means, if someone is linking the whole ASoC into the kernel, they
will not be able to build this as a module. Not a big deal, but you're
stealing some freedom from the user.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This flag was only set for barrier buffers, which we don't submit
anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Remove support for barriers on discards, which is unused now. Also
remove the DISCARD_NOBARRIER I/O type in favour of just setting the
rw flags up locally in blkdev_issue_discard.
tj: Also remove DISCARD_SECURE and use REQ_SECURE directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>