It has been observed that on certain chipsets a peer can be assigned
peer_id=0. For reception of non-aggregated MPDUs this is fine as
ath11k_dp_rx_h_find_peer() has a fallback case where it locates the peer
based upon the source MAC address. On an aggregated link, the mpdu_start
header is only populated by hardware on the first sub-MSDU. This causes
the peer resolution to be skipped for the subsequent MSDUs and the
encryption type of these frames to be set to an incorrect value,
resulting in these MSDUs being dropped by ieee80211.
ath11k_pci 0000:03:00.0: data rx skb 000000002f4b704d len 1534 peer xx:xx:xx:xx:xx:xx 0 ucast sn 3063 he160 rate_idx 9 vht_nss 2 freq 5240 band 1 flag 0x40d1a fcs-err 0 mic-err 0 amsdu-more 0 peer_id 0 first_msdu 1 last_msdu 0
ath11k_pci 0000:03:00.0: data rx skb 0000000038acd580 len 1534 peer (null) 0 ucast sn 3063 he160 rate_idx 9 vht_nss 2 freq 5240 band 1 flag 0x40d00 fcs-err 0 mic-err 0 amsdu-more 0 peer_id 0 first_msdu 0 last_msdu 1
Remove the null peer_id checks in ath11k_dp_rx_h_find_peer() and
ath11k_hal_rx_parse_mon_status_tlv(), allowing peers with an assigned ID
of 0 to be resolved.
Tested-on: QCA2066 hw2.1 PCI WLAN.HSP.1.1-03926.13-QCAHSPSWPL_V2_SILICONZ_CE-2.52297.9
Fixes: 2167fa606c ("ath11k: Add support for RX decapsulation offload")
Reviewed-by: Baochen Qiang <baochen.qiang@oss.qualcomm.com>
Signed-off-by: Matthew Leach <matthew.leach@collabora.com>
Reviewed-by: P Praneesh <praneesh.p@oss.qualcomm.com>
Link: https://patch.msgid.link/20260424-ath11k-null-peerid-workaround-v4-1-252b224d3cf6@collabora.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The mt8167 DSI controller is fully compatible with the one found in
mt2701. Unfortunately the device tree has a dedicated compatible for
mt8167 since 2022 and it cannot be changed with a fallback nor removed at
this point. The only way to get the device to work is to add the
compatible to the driver.
Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20260505214541.333657-3-l.scorcia@gmail.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
ctxfi stores the Line Capture Switch and Mic Capture Switch controls in
a file-scope kctls[] array so do_line_mic_switch() can notify the
opposite control when the shared line/mic input selection changes.
That storage is shared by all ctxfi cards. If more than one X-Fi card is
present, a later card can overwrite the pointers saved by an earlier one.
A control update on one card can then use another card's kcontrol object
for snd_ctl_notify(). If that other card is removed, the saved pointer can
also become stale.
Store those notification targets in struct ct_mixer instead. The mixer is
per-card state and matches the lifetime of the controls created for that
card.
Signed-off-by: Cássio Gabriel <cassiogabrielcontato@gmail.com>
Link: https://patch.msgid.link/20260517-alsa-ctxfi-mixer-kctls-v1-1-6e4f81f6b658@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace DRM_INFO(), DRM_WARN() and DRM_ERROR() calls in
drivers/gpu/drm/mediatek/mtk_dsi.c with the corresponding
drm_info(), drm_warn() and drm_err() helpers.
The drm_*() logging helpers take a struct drm_device * argument,
allowing the DRM core to prefix log messages with the correct device
name and instance. This is required to correctly distinguish log
messages on systems with multiple GPUs.
This change aligns the radeon driver with the DRM TODO item:
"Convert logging to drm_* functions with drm_device parameter".
Signed-off-by: Abhishek Rajput <abhiraj21put@gmail.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20260420052008.5417-1-abhiraj21put@gmail.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The register COMMON_SLICE_CHICKEN4 is a MCR register on both Xe2 and
Xe3. Let's make sure to define a MCR version of it and use it for the
relevant IP versions.
Use XEHP_ as prefix for the register name, since it is MCR as of Xe_HP.
v2:
- Also change for one entry in lrc_tunnings, which was caught by
manual testing and add corresponging Fixes tag in commit message.
(Gustavo)
Fixes: 8d6f16f1f0 ("drm/xe: Extend Wa_22021007897 to Xe3 platforms")
Fixes: e5c13e2c50 ("drm/xe/xe2hpg: Add Wa_22021007897")
Fixes: 8ccf5f6b22 ("drm/xe/tuning: Apply windower hardware filtering setting on Xe3 and Xe3p")
Bspec: 66534, 71185, 74417
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patch.msgid.link/20260514-rtp-mcr-check-v3-3-30dd47855fee@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
(cherry picked from commit 75f65f1a4c)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The register COMMON_SLICE_CHICKEN1 is a MCR register on Xe2.
Let's make sure to define a MCR version of it and use it for the
relevant IP versions.
Use XEHP_ as prefix for the register name, since it is MCR as of Xe_HP.
Fixes: a5d221924e ("drm/xe/xe2_hpg: Add set of workarounds")
Fixes: 9f18b55b6d ("drm/xe/xe2: Add workaround 18033852989")
Bspec: 66534, 71185
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patch.msgid.link/20260514-rtp-mcr-check-v3-2-30dd47855fee@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
(cherry picked from commit a672725fdb)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
CACHE_MODE_1 is a MCR register for all platforms that currently use it
in the Xe driver. Use XE_REG_MCR() when defining it.
Fixes: 8cd7e97597 ("drm/xe: Add missing DG2 lrc workarounds")
Fixes: ff063430ca ("drm/xe/mtl: Add some initial MTL workarounds")
Bspec: 66534, 67788
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patch.msgid.link/20260514-rtp-mcr-check-v3-1-30dd47855fee@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
(cherry picked from commit 8f765f0c05)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reading debugfs file (/sys/kernel/debug/dri/0/gt*/pf/adverse_events)
with CFI (Control Flow Integrity) enabled, the kernel panics at
xe_gt_debugfs_simple_show+0x82/0xc0.
xe_gt_debugfs_simple_show() declare a function pointer expecting int
return type, but xe_gt_sriov_pf_monitor_print_events() is void return
type, leading to CFI failure and kernel panic.
[507620.973657] CFI failure at xe_gt_debugfs_simple_show+0x82/0xc0 [xe]
(target: xe_gt_sriov_pf_monitor_print_events+0x0/0x130 [xe]; expected
type: 0xd72c7139)
Fix xe_gt_sriov_pf_monitor_print_events() function by updating to return
an int type.
Fixes: 1c99d3d3ed ("drm/xe/pf: Expose PF monitor details via debugfs")
Signed-off-by: Mohanram Meenakshisundaram <mohanram.meenakshisundaram@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patch.msgid.link/20260514174918.1556357-2-mohanram.meenakshisundaram@intel.com
(cherry picked from commit ff1d386a83)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We have plugged-in existing VF print functions into our GT debugfs
show helper as-is, but we missed that the helper expects functions
to return int, while they were defined as void. This can lead to
errors being reported when CFI is enabled.
Fixes: 63d8cb8fe3 ("drm/xe/vf: Expose SR-IOV VF attributes to GT debugfs")
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Mohanram Meenakshisundaram <mohanram.meenakshisundaram@intel.com>
Reviewed-by: Shuicheng Lin <shuicheng.lin@intel.com>
Link: https://patch.msgid.link/20260514155726.7165-1-michal.wajdeczko@intel.com
(cherry picked from commit 314e31c9a8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The error path in xe_gsc_init_post_hwconfig() explicitly frees a BO
allocated with xe_managed_bo_create_pin_map() via
xe_bo_unpin_map_no_vm(). Since the managed BO already has a devm
cleanup action registered, this causes a double-free when devm
unwinds during probe failure.
Remove the explicit free and let devm handle it, consistent with
all other xe_managed_bo_create_pin_map() callers.
Fixes: 2e5d47fe78 ("drm/xe/uc: Use managed bo for HuC and GSC objects")
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Assisted-by: Claude:claude-opus-4.6
Link: https://patch.msgid.link/20260511154134.223696-1-shuicheng.lin@intel.com
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
(cherry picked from commit 71d61e3e29)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
To workaround some corner case hardware limitations, new programming
note for the memory based interrupt handler suggests to assume that
some status bytes, like GT_MI_USER_INTERRUPT and GUC_INTR_GUC2HOST,
are always set. Update our interrupt handler to follow the new rules.
Bspec: 53672
Fixes: a6581ebe76 ("drm/xe/vf: Introduce Memory Based Interrupts Handler")
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patch.msgid.link/20260511172838.2299-2-michal.wajdeczko@intel.com
(cherry picked from commit 284f4cae45)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Introduce a device tree node for the AST2600 PWM/Tach controller.
Describe register range, clock, reset, and cell configuration.
Set status to "disabled" by default.
Prepares for enabling PWM and tachometer support on platforms
utilizing this SoC.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Core usually prints endpoint addresses with 0x%X format.
Change this code to use it too, instead of just %d.
Particularly for IN, 0x83 seems more readable than 131.
While at that, fix checkpatch warnings about multi-line
quoted strings, as well as missing or doubled whitespace
in those strings.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Link: https://patch.msgid.link/20260518073258.6532bdd5.michal.pecio@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tao Xue found that some common devices violate USB 3.x section 9.6.7
by reporting wBytesPerInterval lower than the size of packets they
actually send. I confirmed that AX88179 may set it to 0 and RTL8153
CDC configuration sets it to 8 but sends both 8 and 16 byte packets:
S Ii:11:007:3 -115:128 16 <
C Ii:11:007:3 0:128 8 = a1000000 01000000
S Ii:11:007:3 -115:128 16 <
C Ii:11:007:3 0:128 16 = a12a0000 01000800 00000000 00000000
Most xHCI host controllers neglect interrupt bandwidth reservations
and let such devices exceed theirs, some fail the URB with EOVERFLOW.
Assume that wBytesPerInterval lower than wMaxPacketSize is bogus and
increase it to the worst case maximum on interrupt IN endpoints. This
solves xHCI problems and appears to have no other effect. Interrupt
transfers are not limited to one interval and drivers submit URBs of
class defined size without looking at wBytesPerInterval. Any multi-
interval transfer is considered terminated by a packet shorter than
wMaxPacketSize regardless of wBytesPerInterval - see USB3 8.10.3.
Stay in spec on OUT endpoints and isochronous. No buggy devices are
known and we don't want to risk sending more data than the device
is prepared to handle or confusing isoc drivers regarding altsetting
capacities guaranteed by the device itself. And don't complain when
wMaxPacketSize <= wBytesPerInterval < wMaxPacketSize * (bMaxBurst+1)
because enabling this seems to be the exact goal of the spec.
Reported-and-tested-by: Tao Xue <xuetao09@huawei.com>
Closes: https://lore.kernel.org/linux-usb/20260402021400.28853-1-xuetao09@huawei.com/
Cc: stable@vger.kernel.org
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Link: https://patch.msgid.link/20260518073207.5b7d26e7.michal.pecio@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no good reason to have wBytesPerInterval < wMaxPacketSize -
either one is too low or the other too high, and we may want to warn
about such descriptors. Start with cleaning up our own root hubs.
USB 3.2 section 10.15.1 sets wMaxPacketSize and wBytesPerInterval of
SuperSpeed hub status endpoints at 2 bytes, so reduce wMaxPacketSize
from its former value of 4, which was derived from USB 2.0 spec and
the kernel's USB_MAXCHILDREN limit. They don't apply because USB 3.2
10.15.2.1 specifies SuperSpeed hubs to have up to 15 ports.
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Link: https://patch.msgid.link/20260518073121.7bc1da0f.michal.pecio@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently, a few races have been discovered in the GEM LRU logic, all
of them caused by the fact the LRU lock is accessed through
gem->lru->lock, and that very same lock also protects changes to
gem->lru, leading to situations where gem->lru needs to first be
accessed without the lock held, to then get the lru to access the lock
through and finally take the lock and do the expected operation.
Currently, the only driver making use of this API (MSM) declares a
device-wide lock, and the user we're about to add (panthor) will
do the same. There's no evidence that we will ever have a driver
that wants different pools of LRUs protected by different locks under
the same drm_device. So we're better off moving this lock to drm_device
and always locking it through obj->dev->gem_lru_mutex, or directly
through dev->gem_lru_mutex.
If anyone ever needs more fine-grained locking, this can be revisited
to pass some drm_gem_lru_pool object representing the pool of LRUs
under a specific lock, but for now, the per-device lock seems to be
enough.
Fixes: e7c2af13f8 ("drm/gem: Add LRU/shrinker helper")
Reported-by: Chia-I Wu <olvaffe@gmail.com>
Closes: https://gitlab.freedesktop.org/panfrost/linux/-/work_items/86
Reviewed-by: Rob Clark <rob.clark@oss.qualcomm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Link: https://patch.msgid.link/20260518-panthor-shrinker-fixes-v4-1-1920234470d5@collabora.com
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
do_flash() locates the first .cyacd record with
p = strnchr(fw->data, fw->size, ':');
while (p < eof) {
s = strnchr(p + 1, eof - p - 1, ':');
...
}
If the firmware image contains no ':' byte, strnchr() returns NULL.
NULL compares less than the valid kernel pointer eof, so the loop body
runs and strnchr() is called with p + 1 == (void *)1 and a length of
roughly (unsigned long)eof, causing a wonderful crash.
The not_signed_fw fallthrough earlier in do_flash() and the chip-state
branches in ccg_fw_update_needed() allow an unsigned blob to reach this
loop, so a root user who can place a crafted file under /lib/firmware
and write the do_flash sysfs attribute can trigger the oops.
Bail out with -EINVAL when the initial strnchr() returns NULL.
Assisted-by: gkh_clanker_t1000
Cc: stable <stable@kernel.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patch.msgid.link/2026051405-posture-shrill-7884@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WebUSB GET_URL handler in composite_setup() narrows
landing_page_length to fit the host-supplied wLength using
landing_page_length = w_length
- WEBUSB_URL_DESCRIPTOR_HEADER_LENGTH + landing_page_offset;
If wLength is smaller than WEBUSB_URL_DESCRIPTOR_HEADER_LENGTH the
unsigned subtraction wraps, and the subsequent
memcpy(url_descriptor->URL,
cdev->landing_page + landing_page_offset,
landing_page_length - landing_page_offset);
ends up copying close to UINT_MAX bytes from cdev->landing_page into
cdev->req->buf. KASAN reports a slab-out-of-bounds in composite_setup
on the kmalloc-2k gadget_info allocation, and FORTIFY_SOURCE traps the
memcpy as a 4294967293-byte field-spanning write into
url_descriptor->URL (size 252).
A USB host can reach this from a single SETUP packet against any
gadget that has webusb/use=1 and a landingPage configured.
Handle the small-wLength case before the math: when the host requested
fewer bytes than the URL descriptor header, only the header is
meaningful and no URL bytes need to be copied. Setting
landing_page_length to landing_page_offset makes the existing memcpy a
no-op and leaves the descriptor returned to the host unchanged for all
larger wLength values.
Fixes: 93c473948c ("usb: gadget: add WebUSB landing page support")
Cc: stable <stable@kernel.org>
Signed-off-by: Jeremy Erazo <mendozayt13@gmail.com>
Link: https://patch.msgid.link/20260512160530.352318-1-mendozayt13@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the error code on these two error paths. The existing code returns
success.
Fixes: 77ed2f4538 ("usb: typec: tipd: Use read_power_status function in probe")
Fixes: 04041fd7d6 ("usb: typec: tipd: Read data status in probe and cache its value")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://patch.msgid.link/agL9o7wUK1dOVBTy@stanley.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ovl_iterate_merged() stores PTR_ERR(cache) in err before checking
IS_ERR(cache). On success err holds the truncated cache pointer and
can be returned as a bogus non-zero error.
The syzbot reproducer reaches this through overlay-on-overlay readdir:
getdents64
iterate_dir(outer overlay file)
ovl_iterate_merged()
ovl_cache_get()
ovl_dir_read_merged()
ovl_dir_read()
iterate_dir(inner overlay file)
ovl_iterate_merged()
Only compute PTR_ERR(cache) on the error path.
Fixes: d25e4b739f ("ovl: refactor ovl_iterate() and port to cred guard")
Reported-by: syzbot+a16fb0cce329a320661c@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=a16fb0cce329a320661c
Cc: stable@vger.kernel.org
Signed-off-by: Nirmoy Das <nirmoyd@nvidia.com>
Link: https://patch.msgid.link/20260514144258.3068715-1-nirmoyd@nvidia.com
Signed-off-by: Christian Brauner <brauner@kernel.org>
Add an MP5998 power monitor used to monitor the power consumption
of the Paddle_P12V_HSC rail on the Yosemite5 paddle board.
[arj: Remove changelog from commit message]
Signed-off-by: Daniel Hsu <Daniel-Hsu@quantatw.com>
Link: https://patch.msgid.link/20260331120734.39260-1-Daniel-Hsu@quantatw.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
dm_poll_bio() is the ->poll_bio() callback for a stacked dm device.
The caller only knows about the dm queue, so it may decide to do a
spinning poll if it thinks a single queue is being polled. Passing those
flags unchanged to the mapped clone lets blk_mq_poll() spin on a target
queue from inside dm_poll_bio().
With io_uring IOPOLL on a dm-stripe target this can keep a task in
dm_poll_bio() -> bio_poll() -> blk_mq_poll()
long enough to trigger an RCU CPU stall, before io_uring gets back to
io_iopoll_check() and its need_resched() check.
Keep dm's ->poll_bio() bounded by forcing one-shot polling for target
bios. The caller can invoke dm_poll_bio() again if it wants to keep
polling, and it also gets a chance to reap completions or reschedule
between passes.
Fixes: f22ecf9c14 ("blk-mq: delete task running check in blk_hctx_poll()")
Signed-off-by: Fengnan Chang <changfengnan@bytedance.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
When we send a message to a device that has no table, the return code was
not set. The code would return "2", which is not considered a valid return value.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Marzinski <bmarzins@redhat.com>
This adds the admin-guide documentation for dm-inlinecrypt.
dm-inlinecrypt.rst is the guide to using dm-inlinecrypt.
Signed-off-by: Linlin Zhang <linlin.zhang@oss.qualcomm.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
As described in commit 2bc0576925 ("block: don't make REQ_POLLED imply
REQ_NOWAIT"), which fixed the same issue for the block device node, there
are valid cases to poll for I/O completion without REQ_NOWAIT.
Additionally, sing REQ_NOWAIT for file system writes is currently not
supported as file systems writes are not idempotent and would need a
retry of just the bio and not the entire operation to be fully supported.
Switch iomap to set REQ_POLLED and remove the now unused bio_set_polled
helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://patch.msgid.link/20260518062917.506483-1-hch@lst.de
Signed-off-by: Christian Brauner <brauner@kernel.org>
The current SysFS flow first enables the links and sink, then rolls back
to disable them if the source fails to enable. This failure can occur if
the associated CPU is offline, which causes the SMP call to fail.
Validate whether the associated CPU is online for a per-CPU tracer.
If the CPU is offline, return -ENODEV and bail out.
Tested-by: James Clark <james.clark@linaro.org>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-28-f88c4a3ecfe9@arm.com
This commit moves CPU hotplug callbacks from ETMv4 driver to core layer.
The motivation is the core layer can control all components on an
activated path rather but not only managing tracer in ETMv4 driver.
The perf event layer will disable CoreSight PMU event 'cs_etm' when
hotplug off a CPU. That means a perf mode will be always converted to
disabled mode in CPU hotplug. Arm CoreSight CPU hotplug callbacks only
need to handle the Sysfs mode and ignore the perf mode.
Add a 'mode' argument to coresight_pm_get_active_path() so it only
returns active paths for the relevant mode. Define the enum with bit
flags so it is safe for bitwise operations.
Change CPUHP_AP_ARM_CORESIGHT_STARTING to CPUHP_AP_ARM_CORESIGHT_ONLINE
so that the CPU hotplug callback runs in the online state and thread
context, allowing coresight_disable_sysfs() to be called directly to
disable the path.
Tested-by: James Clark <james.clark@linaro.org>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-27-f88c4a3ecfe9@arm.com
Except for software sources (e.g. STM), other sources treat multiple
enables as equivalent to a single enable. The device mode already
tracks the binary state, so it is redundant to operate refcount.
Introduce a helper coresight_is_software_source() for check software
source. Refactor to maintain the refcount only for software sources.
This simplifies future CPU PM handling without refcount logic.
Tested-by: James Clark <james.clark@linaro.org>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-26-f88c4a3ecfe9@arm.com
Add interrupt-parent and interrupts properties to the PDB PCA9555
nodes in the anacapa DTS.
[arj: Tweak commit subject capitalisation]
Signed-off-by: Rex Fu <Rex.Fu@amd.com>
Link: https://patch.msgid.link/20260417-anacapa-pca9555-irq-v1-1-9a6d28b1b656@amd.com
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Instead of projecting using pointer to a field project the full slot. This
further shifts the code generation from the initializer site to the struct
definition site, which means less code is generated overall.
It also makes the safety comment easier to justify, as now the projection
is done by the `#[pin_data]` macro which has full visibility of pinnedness
of fields.
The field alignment could also be checked on the `#[pin_data]` side;
however, since `init!()` macro works for other type of structs, we cannot
remove the alignment check from `init!`/`pin_init!` side anyway, so I opted
to still keep the alignment check in init.rs.
Signed-off-by: Gary Guo <gary@garyguo.net>
By projecting slots, the `pin_init!` and `init!` code path can be more
unified. This also reduces the amount of macro-generated code and shifts
them to the shared infrastructure.
Signed-off-by: Gary Guo <gary@garyguo.net>
The `InitData` and `PinData` traits do not need to exist, the inference
helpers could be inherent methods instead.
There is no risk for calling the wrong methods even when user defines it,
as inherent methods take priority over trait methods.
With this change, it unlocks the possibility of attaching additional bounds
to the method per type, which is not possible for trait methods.
Signed-off-by: Gary Guo <gary@garyguo.net>
Instead of projecting the created reference, simply create drop guards with
different marker types and have the `let_binding()` method of guards of
different marker produce different type instead.
This allows more flexible lifetime as this is now controlled by the guard.
This will be needed when implementing self-referential fields.
Signed-off-by: Gary Guo <gary@garyguo.net>
`InitializerKind::Code` is a special case where it does not initialize a
field, and thus generate no guard and accessors. Handle it earlier and make
the rest of the code more linear.
Signed-off-by: Gary Guo <gary@garyguo.net>
The ACS specification does not allow a non-NCQ command to be issued while
an NCQ command is outstanding.
Commit 0ea84089db ("ata: libata-scsi: avoid Non-NCQ command starvation")
introduced a feature where a deferred non-NCQ command gets issued from a
workqueue. The design stores a single non-NCQ command per port.
However, when using Port Multipliers (PMPs), specifically PMPs that
support FIS-Based Switching (FBS), non-NCQ and NCQ commands can be mixed
on the same port, just not for the same link, see e.g. ata_std_qc_defer()
which is, and always has operated on a per-link basis.
Therefore, move the deferred_qc from struct ata_port to struct ata_link.
This way, when using a PMP with FBS, we will not needlessly defer commands
to all other links, just because one link issued a non-NCQ command while
having an NCQ command outstanding. Only commands for that specific link
will be deferred. This is in line with how PMPs with FBS worked before
commit 0ea84089db ("ata: libata-scsi: avoid Non-NCQ command starvation").
Fixes: 0ea84089db ("ata: libata-scsi: avoid Non-NCQ command starvation")
Tested-by: Tommy Kelly <linux@tkel.ly>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
When using Port Multipliers (PMPs) with Command-Based Switching (CBS), you
can only issue commands to one link at a time. For PMPs with CBS, there is
already code to handle commands being sent to different links in
sata_pmp_qc_defer_cmd_switch() using ap->excl_link. sata_sil24 also makes
use of ap->excl_link.
A user on the list reported that commit 0ea84089db ("ata: libata-scsi:
avoid Non-NCQ command starvation") broke PMPs with CBS. The commit
introduced code that stores a deferred qc in ap->deferred_qc, to later be
issued via a workqueue. It turns out that this change is incompatible with
the existing ap->excl_link handling used by PMPs with CBS.
Thus, modify sata_pmp_qc_defer_cmd_switch() and sil24_qc_defer() to return
ATA_DEFER_LINK_EXCL, and make sure that the deferred QC handling via
workqueue is not used for this return value.
This way, PMPs with CBS will work once again. Note that the starvation
referenced in commit 0ea84089db ("ata: libata-scsi: avoid Non-NCQ
command starvation") can only happen on libsas ports, and libsas does not
support Port Multipliers, thus there is no harm of reverting back to the
previous way of deferring commands for PMPs with CBS.
Non-libsas ports connected to anything but a PMP with CBS (e.g. a normal
drive or a PMP with FBS) will continue using the deferred workqueue, since
it does result in lower completion latencies for non-NCQ commands, even
though the workqueue is not strictly needed to avoid starvation for
non-libsas ports.
If we want to modify the scope of the workqueue issuing to also handle
PMPs with CBS, then we should ensure that we can save both NCQ and non-NCQ
commands in ap->deferred_qc, while also removing the existing PMP CBS
handling using ap->excl_link, such that we don't duplicate features.
While at it, also add a comment explaining how the ap->excl_link mechanism
works.
Fixes: 0ea84089db ("ata: libata-scsi: avoid Non-NCQ command starvation")
Tested-by: Tommy Kelly <linux@tkel.ly>
Reported-by: Tommy Kelly <linux@tkel.ly>
Closes: https://lore.kernel.org/linux-ide/ce09cc21-a8e9-4845-b205-35411e22fba9@tkel.ly/
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Commit 18226ba521 ("drm/syncobj: reject invalid flags in
drm_syncobj_find_fence") forgot to take into account the fact that
drm_syncobj_find() takes a reference to syncobj and returns early
without dropping the reference, leading to memory leaks.
Fixes: 18226ba521 ("drm/syncobj: reject invalid flags in drm_syncobj_find_fence")
Reported by: Sam Spencer <sam.spencer@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Erik Kurzinger <ekurzinger@gmail.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://lore.kernel.org/all/20260507144425.2488057-1-liviu.dudau@arm.com
The deferred QC feature was meant to handle mixed NCQ and non-NCQ commands,
i.e. for return value ATA_DEFER_LINK.
ATA_DEFER_PORT is returned by PATA drivers, but also certain SATA drivers
like sata_mv and sata_sil24 that uses ap->excl_link to workaround hardware
bugs in these HBAs. Regardless of the reason, using the deferred QC feature
for ATA_DEFER_PORT is always wrong, and will break the ap->excl_link usage
of the SATA drivers that rely on that feature.
Modify ata_scsi_qc_issue() to only use the deferred QC feature when mixing
NCQ and non-NCQ commands, i.e. ATA_DEFER_LINK.
Fixes: 0ea84089db ("ata: libata-scsi: avoid Non-NCQ command starvation")
Tested-by: Tommy Kelly <linux@tkel.ly>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Improve readability of ata_scsi_qc_issue().
No functional changes.
Tested-by: Tommy Kelly <linux@tkel.ly>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Commit 64a6b57749 ("regulator: tps65219: Remove debugging helper
function") removed the tps65219_get_rdev_by_name() helper along with
the irq_data.rdev assignment that depended on it. This left
irq_data.rdev uninitialized for all IRQs, causing undefined behavior
when regulator_notifier_call_chain() is called from the IRQ handler:
Internal error: Oops: 0000000096000004
pc : regulator_notifier_call_chain
lr : tps65219_regulator_irq_handler
Call trace:
regulator_notifier_call_chain
tps65219_regulator_irq_handler
handle_nested_irq
regmap_irq_thread
irq_thread_fn
irq_thread
kthread
ret_from_fork
Instead of restoring a dedicated lookup array, restructure the probe
function to combine regulator registration with IRQ registration in
the same loop. This way the rdev returned by devm_regulator_register()
is naturally available for assigning to irq_data.rdev without any
auxiliary data structure.
Non-regulator IRQs (SENSOR, TIMEOUT) that don't correspond to any
registered regulator are registered with rdev=NULL, and the IRQ handler
is protected with a NULL check to avoid crashing.
Cc: stable@vger.kernel.org
Closes: https://lore.kernel.org/all/aBDSTxALaOc-PD7X@gaggiata.pivistrello.it/
Reported-by: Francesco Dolcini <francesco@dolcini.it>
Fixes: 64a6b57749 ("regulator: tps65219: Remove debugging helper function")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://patch.msgid.link/20260518083113.2063368-1-alexander.sverdlin@siemens.com
Signed-off-by: Mark Brown <broonie@kernel.org>
TRBE context can be lost when a CPU enters low power states. If a trace
source is restored while TRBE is not, tracing may run without an active
sink, which can lead to hangs on some devices (e.g., Pixel 9).
The save and restore flows are described in the section K5.5 "Context
switching" of Arm ARM (ARM DDI 0487 L.a). This commit adds save and
restore callbacks with following the software usages defined in the
architecture manual.
During the restore flow, since TRBLIMITR_EL1.E resets to 0 on a warm
reset, the trace buffer unit is disabled when idle resume, it is safe to
restore base/pointer/status registers first and program TRBLIMITR_EL1
last.
Signed-off-by: Yabin Cui <yabinc@google.com>
Co-developed-by: Leo Yan <leo.yan@arm.com>
Signed-off-by: Leo Yan <leo.yan@arm.com>
Reviewed-by: James Clark <james.clark@linaro.org>
Tested-by: James Clark <james.clark@linaro.org>
Reviewed-by: Yeoreum Yun <yeoreum.yun@arm.com>
Tested-by: Jie Gan <jie.gan@oss.qualcomm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20260515-arm_coresight_path_power_management_improvement-v14-25-f88c4a3ecfe9@arm.com
The thermistor device nodes were added before the vbus regulator and
reserved memory nodes, when they should be after them, based on
alphabetical order of the device node _name_.
Move them to the correct position. No functional changes intended.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The names currently given to the EC controlled regulators do not match
what is used in the hardware design.
Fix the names and the labels.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
GPIO lines 59 and 61 are named BT_KILL_1V8_L and WIFI_KILL_1V8_L in the
hardware design. Add them to the gpio-line-names property to make the
names available to users and developers.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
For JEDEC compatible SPI NOR chips, there should be a single generic
"jedec,spi-nor" compatible.
Drop the model-specific compatible from the flash node.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
The it66121_ctx structure has a gpio_reset field, and it66121_hw_reset()
calls gpiod_set_value() on it. However, the GPIO descriptor is never
acquired via devm_gpiod_get(), leaving gpio_reset as NULL throughout
the driver lifetime.
gpiod_set_value() silently returns when passed a NULL descriptor, so
the hardware reset sequence in it66121_hw_reset() is a no-op. This
leaves the chip in an undefined state at probe time, which can prevent
it from responding on the I2C bus.
The DT binding marks reset-gpios as a required property, so all
compliant device trees provide this GPIO. Add the missing
devm_gpiod_get() call after enabling power supplies and before the
hardware reset, so the chip is properly reset with power applied.
Fixes: 988156dc2f ("drm: bridge: add it66121 driver")
Cc: stable@vger.kernel.org
Signed-off-by: Julien Chauveau <chauveau.julien@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patch.msgid.link/20260324193011.16583-1-chauveau.julien@gmail.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Johan Hovold <johan@kernel.org> says:
In preparation for fixing the SPI controller API so that it no longer
drops a reference when deregistering (non-managed) controllers (cf.
[1]), this series converts drivers using managed registration to also
use managed allocation.
Included is also a related cleanup of a lp8841-rtc.
This leaves us with 18 drivers using non-managed allocation, which is
few enough to be able to fix the API in tree-wide change.
Johan
[1] https://lore.kernel.org/lkml/20260325145319.1132072-1-johan@kernel.org/
Link: https://patch.msgid.link/20260511150408.796155-1-johan@kernel.org
