If the user disables power save of a vif that didn't have it enabled
(for example before association), mac80211 will not notify the driver
with BSS_CHANGED_PS. This will cause the driver to not update the
device-level power save to disabled.
Fix this by checking the vif's power save status upon authorization, and
stop considering the vif's power save status on disassociation.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250309073442.1cdeb78b19ba.I58fe02c062524029071b04b093a1b09c5e46f4ef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When running secured ranging and the initiator is associated with
the responder, the TK was not set in the range request command.
Fix it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.603dc31579d9.Icd19d797e56483c08dd22c55b96fee481c4d2f3d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_trans_reclaim is warning if it is called when the FW is not alive.
But if it is called when there is a pending restart, i.e. after a FW
error, there is no need to warn, instead - return silently.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.ba3d90b22c25.I9332506af1997faefcf0bdb51d98d5e874051722@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Corrected the bit size calculation in the for_each_set_bit macro in
the iwl_dbgfs_tas_get_status_read(). The previous implementation used
sizeof(dyn_status), which only accounts for the number of bytes.
This has been updated to TAS_DYNA_STATUS_MAX to ensure the loop iterates
over the correct number of valid bits in dyn_status.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.65d373e4a10e.If2cea63035333b07849e5a2c2a4f5dc5c5239595@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FW is now responsible of determining the SMPS mode.
If the user disabled power save in a certain vif, we send the vif-level
power command to clear out the POWER_FLAGS_POWER_MANAGEMENT_ENA_MSK bit
for that vif.
But erroneously, the FW checks DEVICE_POWER_FLAGS_POWER_SAVE_ENA_MSK in
the device-level command to determine the SMPS mode.
To W/A this, send also the device-level command when the power save of a
vif changes, and disable power save if there is any vif that has power
save disabled.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.7bf205efa027.I2c793ff1fc2a6779a95faaee1ded348100fd97f1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The order of actions taken for debug was implemented incorrectly.
Now we implemented the dump split and do the FW reset only in the
middle of the dump (rather than the FW killing itself on error.)
As a result, some of the actions taken when applying the config
will now crash the device, so we need to fix the order.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.6de7fa8e63ed.I40632c48e2a67a8aca05def572a934b88ce7934b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new reason is added to the iwl_tas_statically_disabled_reason enum
and the corresponding message is updated in the
iwl_dbgfs_tas_get_status_read().
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.5e1272ef3508.I24f668ae716bee20cba15fdc73c3363693bbaf73@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Removed mvm prefix from the following structures and enum names:
1. struct iwl_tas_status_per_mac
2. struct iwl_tas_status_resp
3. enum iwl_tas_dyna_status
4. enum iwl_tas_statically_disabled_reason
As these structures and enums are not specific to mvm.
Replaced TAS_LMAC_BAND_LB, TAS_LMAC_BAND_HB, and TAS_LMAC_BAND_UHB macros
with a generic BAND macro, as these macros are not specific to TAS.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231427.59144bee9987.Ic2678dcb5afdacc2ca234d4aa4901e7e1f6e8dbb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This UEFI variable name was badly named. Fix its name and also use the
right GUID to find it: we need to use the BT_WIFI (a.k.a. Common) GUID.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308231426.78c998d0fa71.I2bc9d72c1dc2c4d7028f0265634a940c2fadbbb5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the multi-link reconfiguration frame, the per-STA profile for
added links shouldn't include the multi-link element. Set the
association ID to an invalid value, so it doesn't erroneously
match the link ID if that happens to be zero.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308225541.8e5be244c70f.I3472cd5c347814ee3600869a88488997bcd43224@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If disconnecting while ML reconfiguration is in progress,
the data isn't freed because the reset call is too late,
after the vif already switches to non-MLD. Move the call
to fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308225541.abaea69cde42.I7e6b35731ded94fc2d68a2d4ecf81873712c268e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If multi-link reconfiguration fails, we can disconnect with a local link
already allocated but the BSS entry not assigned yet, which leads to a
warning in cfg80211. Add a check to avoid the warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308225541.699bd9cbabe5.I599d5ff69092a65e916e2acd25137ae9df8debe8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Spotted during code review, the selectors need to be large
enough for a 128-bit bitmap, not a single unsigned long,
otherwise we have stack corruption.
We should also allow passing selectors from userspace, but
that should be a separate change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308225541.8f1bcf96a504.Ibeb8970c82a30c97279a4cc4e68faca5df1813a5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do address translations only between shared links. It is
possible that while an non-AP MLD station and an AP MLD
station have shared links, the frame is intended to be sent
on a link which is not shared (for example when sending a
probe response).
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308225541.1aa461270bb6.Ic21592e1b1634653f02b80628cb2152f6e9de367@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If U-APSD isn't enabled by us, then IEEE80211_STA_UAPSD_ENABLED
won't be set, but the AP can still support it in that case. Only
require U-APSD from the AP if we enabled it, don't require it to
be disabled on the AP if we didn't.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308225541.b4674be12a38.I01959e448c6a2a3e8bc5d561bbae9e8d2cca616a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some regulatory bodies doesn't allow IR (initiate radioation) on a
specific subband, but allows it for channels with a bandwidth of 20 MHz.
Add a channel flag that indicates that, and consider it in
cfg80211_reg_check_beaconing.
While on it, fix the kernel doc of enum nl80211_reg_rule_flags and
change it to use BIT().
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Co-developed-by: Somashekhar Puttagangaiah <somashekhar.puttagangaiah@intel.com>
Signed-off-by: Somashekhar Puttagangaiah <somashekhar.puttagangaiah@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308225541.d3ab352a73ff.I8a8f79e1c9eb74936929463960ee2a324712fe51@changeid
[fix typo]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support passing the value from userspace on to the AP in the
association and ML link reconfiguration requests. We may need
to also add a driver value to or in with the field, but for
now have no feature that is controlled by the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250308225541.2e555beb0a76.I623f59023b47ec202fc0c7520f2b5f575b439927@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some extended MLD capabilities and operations bits (currently
the "BTM MLD Recommendataion For Multiple APs Support" bit)
may depend on userspace capabilities. Allow userspace to pass
the values for this field that it supports to the association
and link reconfiguration operations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Link: https://patch.msgid.link/20250308225541.bd52078b5f65.I4dd8f53b0030db7ea87a2e0920989e7e2c7b5345@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible to use nl80211 to request to the driver to do allow the
required bus configuration to wake-up the host.
This patch implements the required API for nl80211.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://patch.msgid.link/20250304153224.39083-6-jerome.pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device is connected with SDIO bus, it can wake up the host using
either the SDIO controller (that requires MMC_PM_WAKE_SDIO_IRQ
capability) or the out-of-bound IRQ. This patch allows both.
Obviously, the SDIO controller must be able to keep the SDIO device
powered on.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://patch.msgid.link/20250304153224.39083-5-jerome.pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WF200 is able to keep the connection with the AP alive while the host is
asleep. So, let's expose this capability to the user.
For now, we don't provide any way to control the device filtering
features. The user has to allow wake-up on any received packets and on
disconnections.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://patch.msgid.link/20250304153224.39083-3-jerome.pouiller@silabs.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My previous patch caused a slight code size increase when DEBUG_FS is disabled,
as Stanislaw Gruszka pointed out.
Fix this with an added IS_ENABLED() check.
Fixes: cf6b9ba172 ("wifi: iwlegacy: don't warn for unused variables with DEBUG_FS=n")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://patch.msgid.link/20250304144210.997531-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This development cycle again featured multiple patchsets to ath12k to
support the new 802.11be MLO feature. In addition, there was the usual
set of bug fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCZ8iK9QAKCRAsFbugiYzL
e9P0AP0T2yU1fl3IRw+q9toRv126vJ7eSKWDZXDU1TppGn/FMQEAiI49Jnhp6WaO
e3nbULnMVF+oOoOTWMJrJ3f6aU5C4AE=
=yTAR
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20250305' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
====================
ath.git patches for v6.15
This development cycle again featured multiple patchsets to ath12k to
support the new 802.11be MLO feature. In addition, there was the usual
set of bug fixes and cleanups.
====================
Link: https://lore.kernel.org/linux-wireless/d01b1976-ebe8-48cd-8f49-32bfa00bed7e@oss.qualcomm.com/
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlwifi is the driver of all Intel wifi devices since 2008.
Since then, the hardware has changed a lot, but the firmware
API has changed even more. The need to keep one driver that
supports all those different APIs led us to introduce a new
architecture circa 2012 which allowed us to keep the same
interface to the hardware (DMAs, Tx queues, etc...) with a
new layer to implement the mid-layer between mac80211 and
the firmware. The first component is called the 'transport'
and the latter is called 'operation_mode' a.k.a op_mode.
In 2013 we took advantage of the new architecture to
introduce iwlmvm which allowed us to implement the, then,
new firmware API. This op_mode supports 7260 and up, those
devices supports support at least VHT.
Since then, wifi evolved and so did the firmware. It became
much bigger and took a lot of functionality from the driver.
It became increasingly hard to keep the same op_mode for the
newest devices and we experienced frequent regressions on
older devices. In order to avoid those regressions and keep
the code maintainable, we decided it was about time to start
a new op_mode.
iwlmld is a new op_mode that supports BE200 or newer if the
firmware being used is 97.ucode or newer. If the user has
an older devices or BE200 with .96.ucode, iwlmvm will be
loaded. Of course, this op_mode selection is seamless.
All the features supported in iwlmvm are supported in
iwlmld besides a few seldom used use cases: injection and
Hotspot 2.0. Those are under work.
A few points about the implementation:
* iwlmld doesn't have any mutexes, it relies on the
wiphy_lock
* iwlmld is more "resource oriented": stations, links and
interfaces are allocated and freed only after all the
relevant flows are completed.
* Firmware notifications' sizes are validated in a more
structured way.
We would love to see this new op_mode merged in 6.15. The
firmware for this new driver (.97.ucode) is not yet publicly
available but it'll be sent very soon.
People eager to get an early version of this firmware can
contact Emmanuel at:
emmanuel.grumbach@intel.com
I've listed the people who directly contributed
code, but many others from various teams have
contributed in other ways.
Co-developed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Co-developed-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Co-developed-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Co-developed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Co-developed-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Co-developed-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Co-developed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Co-developed-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://lore.kernel.org/linux-wireless/20250216094321.537988-1-miriam.rachel.korenblit@intel.com/
[fix Kconfig, fix api/phy.h includes, SPDX tag and coding
style issues, duplicated includes per 0-day robot]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* cfg80211/mac80211
- remove cooked monitor support
- strict mode for better AP testing
- basic EPCS support
- OMI RX bandwidth reduction support
* rtw88
- preparation for RTL8814AU support
* rtw89
- use wiphy_lock/wiphy_work
- preparations for MLO
- BT-Coex improvements
- regulatory support in firmware files
* iwlwifi
- preparations for the new iwlmld sub-driver
-----BEGIN PGP SIGNATURE-----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=KYXQ
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2025-03-04-v2' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
First 6.15 material:
* cfg80211/mac80211
- remove cooked monitor support
- strict mode for better AP testing
- basic EPCS support
- OMI RX bandwidth reduction support
* rtw88
- preparation for RTL8814AU support
* rtw89
- use wiphy_lock/wiphy_work
- preparations for MLO
- BT-Coex improvements
- regulatory support in firmware files
* iwlwifi
- preparations for the new iwlmld sub-driver
* tag 'wireless-next-2025-03-04-v2' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (128 commits)
wifi: iwlwifi: remove mld/roc.c
wifi: mac80211: refactor populating mesh related fields in sinfo
wifi: cfg80211: reorg sinfo structure elements for mesh
wifi: iwlwifi: Fix spelling mistake "Increate" -> "Increase"
wifi: iwlwifi: add Debug Host Command APIs
wifi: iwlwifi: add IWL_MAX_NUM_IGTKS macro
wifi: iwlwifi: add OMI bandwidth reduction APIs
wifi: iwlwifi: remove mvm prefix from iwl_mvm_d3_end_notif
wifi: iwlwifi: remember if the UATS table was read successfully
wifi: iwlwifi: export iwl_get_lari_config_bitmap
wifi: iwlwifi: add support for external 32 KHz clock
wifi: iwlwifi: mld: add a debug level for EHT prints
wifi: iwlwifi: mld: add a debug level for PTP prints
wifi: iwlwifi: remove mvm prefix from iwl_mvm_esr_mode_notif
wifi: iwlwifi: use 0xff instead of 0xffffffff for invalid
wifi: iwlwifi: location api cleanup
wifi: cfg80211: expose update timestamp to drivers
wifi: mac80211: add ieee80211_iter_chan_contexts_mtx
wifi: mac80211: fix integer overflow in hwmp_route_info_get()
wifi: mac80211: Fix possible integer promotion issue
...
====================
Link: https://patch.msgid.link/20250304125605.127914-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Breno Leitao says:
====================
netconsole: Add taskname sysdata support
This patchset introduces a new feature to the netconsole extradata
subsystem that enables the inclusion of the current task's name in the
sysdata output of netconsole messages.
This enhancement is particularly valuable for large-scale deployments,
such as Meta's, where netconsole collects messages from millions of
servers and stores them in a data warehouse for analysis. Engineers
often rely on these messages to investigate issues and assess kernel
health.
One common challenge we face is determining the context in which
a particular message was generated. By including the task name
(task->comm) with each message, this feature provides a direct answer to
the frequently asked question: "What was running when this message was
generated?"
This added context will significantly improve our ability to diagnose
and troubleshoot issues, making it easier to interpret output of
netconsole.
The patchset consists of seven patches that implement the following changes:
* Refactor CPU number formatting into a separate function
* Prefix CPU_NR sysdata feature with SYSDATA_
* Patch to covert a bitwise operation into boolean
* Add configfs controls for taskname sysdata feature
* Add taskname to extradata entry count
* Add support for including task name in netconsole's extra data output
* Document the task name feature in Documentation/networking/netconsole.rst
* Add test coverage for the task name feature to the existing sysdata selftest script
These changes allow users to enable or disable the task name feature via
configfs and provide additional context for kernel messages by showing
which task generated each console message.
I have tested these patches on some servers and they seem to work as
expected.
v1: https://lore.kernel.org/r/20250221-netcons_current-v1-0-21c86ae8fc0d@debian.org
Signed-off-by: Breno Leitao <leitao@debian.org>
====================
Link: https://patch.msgid.link/20250228-netcons_current-v2-0-f53ff79a0db2@debian.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add test coverage for the netconsole task name feature to the existing
sysdata selftest script. This extends the test infrastructure to verify
that task names are correctly appended when enabled and absent when
disabled.
The test validates that:
- Task names appear in the expected format "taskname=<name>"
- Task names are included when the feature is enabled
- Task names are excluded when the feature is disabled
- The feature works correctly alongside other sysdata fields like CPU
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add documentation for the netconsole task name feature in
Documentation/networking/netconsole.rst. This explains how to enable
task name via configfs and demonstrates the output format.
The documentation includes:
- How to enable/disable the feature via taskname_enabled
- The format of the task name in the output
- An example showing the task name appearing in messages
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This is the core patch for this whole patchset. Add support for
including the current task's name in netconsole's extra data output.
This adds a new append_taskname() function that writes the task name
(from current->comm) into the target's extradata buffer, similar to how
CPU numbers are handled.
The task name is included when the SYSDATA_TASKNAME field is set,
appearing in the format "taskname=<name>" in the output. This additional
context can help with debugging by showing which task generated each
console message.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add configfs interface to enable/disable the taskname sysdata feature.
This adds the following functionality:
The implementation follows the same pattern as the existing CPU number
feature, ensuring consistent behavior and error handling across sysdata
features.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
New SYSDATA_TASKNAME feature flag to track when taskname append is enabled.
Additional check in count_extradata_entries() to include taskname in
total, counting it as an entry in extradata. This function is used to
check if we are not overflowing the number of extradata items.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Extract CPU number formatting logic from prepare_extradata() into a new
append_cpu_nr() function.
This refactoring improves code organization by isolating CPU number
formatting into its own function while reducing the complexity of
prepare_extradata().
The change prepares the codebase for the upcoming taskname feature by
establishing a consistent pattern for handling sysdata features.
The CPU number formatting logic itself remains unchanged; only its
location has moved to improve maintainability.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Convert the current state assignment to use explicit boolean conversion,
making the code more robust and easier to read. This change adds a
double-negation operator to ensure consistent boolean conversion as
suggested by Paolo[1].
This approach aligns with the existing pattern used in
sysdata_cpu_nr_enabled_show().
Link: https://lore.kernel.org/all/7309e760-63b0-4b58-ad33-2fb8db361141@redhat.com/ [1]
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rename the CPU_NR enum value to SYSDATA_CPU_NR to establish a consistent
naming convention for sysdata features. This change prepares for
upcoming additions to the sysdata feature set by clearly grouping
related features under the SYSDATA prefix.
This change is purely cosmetic and does not modify any functionality.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This file should never have been part of the commit, remove it.
Fixes: af3be90884 ("wifi: iwlwifi: support ROC version 6")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
