While trying to convert the entire delalloc extent is a good decision
for regular writeback as it leads to larger contigous on-disk extents,
but for other callers of xfs_bmapi_write is is rather questionable as
it forced them to loop creating new transactions just in case there
is no large enough contiguous extent to cover the whole delalloc
reservation.
Change xfs_bmapi_write to only allocate the passed in range instead,
whіle the writeback path through xfs_bmapi_convert_delalloc and
xfs_bmapi_allocate still always converts the full extents.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
xfs_bmap_add_extent_delay_real takes parts or all of a delalloc extent
and converts them to a real extent. It is written to deal with any
potential overlap of the to be converted range with the delalloc extent,
but it turns out that currently only converting the entire extents, or a
part starting at the beginning is actually exercised, as the only caller
always tries to convert the entire delalloc extent, and either succeeds
or at least progresses partially from the start.
If it only converts a tiny part of a delalloc extent, the indirect block
calculation for the new delalloc extent (da_new) might be equivalent to that
of the existing delalloc extent (da_old). If this extent conversion now
requires allocating an indirect block that gets accounted into da_new,
leading to the assert that da_new must be smaller or equal to da_new
unless we split the extent to trigger.
Except for the assert that case is actually handled by just trying to
allocate more space, as that already handled for the split case (which
currently can't be reached at all), so just reusing it should be fine.
Except that without dipping into the reserved block pool that would make
it a bit too easy to trigger a fs shutdown due to ENOSPC. So in addition
to adjusting the assert, also dip into the reserved block pool.
Note that I could only reproduce the assert with a change to only convert
the actually asked range instead of the full delalloc extent from
xfs_bmapi_write.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Both callers of xfs_bmapi_allocate already initialize bma->prev, don't
redo that in xfs_bmapi_allocate.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
xfs_bmapi_allocate currently overwrites offset and len when converting
delayed allocations, and duplicates the length cap done for non-delalloc
allocations. Move all that logic into the callers to avoid duplication
and to make the calling conventions more obvious.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
XFS_FILBLKS_MIN uses min_t and thus does the comparison using the correct
xfs_filblks_t type. Use it in xfs_bmapi_write and slightly adjust the
comment document th potential pitfall to take account of this
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
xfs_bmapi_convert_delalloc has a xfs_valid_startblock check on the block
allocated by xfs_bmapi_allocate. Lift it into xfs_bmapi_allocate as
we should assert the same for xfs_bmapi_write.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
tmp_logflags is initialized to 0 and then ORed into bma->logflags, which
isn't actually doing anything.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
xfs_bmapi_write can return 0 without actually returning a mapping in
mval in two different cases:
1) when there is absolutely no space available to do an allocation
2) when converting delalloc space, and the allocation is so small
that it only covers parts of the delalloc extent before the
range requested by the caller
Callers at best can handle one of these cases, but in many cases can't
cope with either one. Switch xfs_bmapi_write to always return a
mapping or return an error code instead. For case 1) above ENOSPC is
the obvious choice which is very much what the callers expect anyway.
For case 2) there is no really good error code, so pick a funky one
from the SysV streams portfolio.
This fixes the reproducer here:
https://lore.kernel.org/linux-xfs/CAEJPjCvT3Uag-pMTYuigEjWZHn1sGMZ0GCjVVCv29tNHK76Cgg@mail.gmail.com0/
which uses reserved blocks to create file systems that are gravely
out of space and thus cause at least xfs_file_alloc_space to hang
and trigger the lack of ENOSPC handling in xfs_dquot_disk_alloc.
Note that this patch does not actually make any caller but
xfs_alloc_file_space deal intelligently with case 2) above.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: 刘通 <lyutoon@gmail.com>
Reviewed-by: "Darrick J. Wong" <djwong@kernel.org>
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
The AllWinner H6 and later SoCs that sport a DMIC block contain a set of registers to control
the gain (left + right) of each of the four supported channels.
Add ASoC controls for changing each of the stereo channel gains using alsamixer and alike
Signed-off-by: Joao Schim <joao@schimsalabim.eu>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240429194920.1596257-1-joao@schimsalabim.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert NVIDIA Tegra30 I2S binding to DT schema and
add "clock-names" property used by multiple tegra i2s blocks
in arch/arm64/boot/dts/nvidia/tegra132.dtsi. This is not a
required property by the binding.
Signed-off-by: Mohammad Shehar Yaar Tausif <sheharyaar48@gmail.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240426170322.36273-1-sheharyaar48@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable CONFIG_INTERCONNECT_QCOM_SM6115 as built-in to enable the
interconnect driver for the SoC used on Qualcomm Robotics RB2 board.
Building as built-in is required as on this platform interconnects are
required to bring up the console.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240424-enable-sm6115-icc-v3-1-21c83be48f0e@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Use phylink_pcs_change() when reporting changes in PCS link state to
phylink as the interrupts are informing us about changes to the PCS
state.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/E1s0OH2-009hgx-Qw@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use phylink_pcs_change() when reporting changes in PCS link state to
phylink as the interrupts are informing us about changes to the PCS
state.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/E1s0OGx-009hgr-NP@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use phylink_pcs_change() when reporting changes in PCS link state to
phylink as the interrupts are informing us about changes to the PCS
state.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/E1s0OGs-009hgl-Jg@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use phylink_pcs_change() when reporting changes in PCS link state to
phylink as the interrupts are informing us about changes to the PCS
state.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/E1s0OGn-009hgf-G6@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We must initialize prune_proxy_timer before we attempt
a del_timer_sync() on it.
syzbot reported the following splat:
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
CPU: 1 PID: 11 Comm: kworker/u8:1 Not tainted 6.9.0-rc5-syzkaller-01199-gfc48de77d69d #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024
Workqueue: netns cleanup_net
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114
assign_lock_key+0x238/0x270 kernel/locking/lockdep.c:976
register_lock_class+0x1cf/0x980 kernel/locking/lockdep.c:1289
__lock_acquire+0xda/0x1fd0 kernel/locking/lockdep.c:5014
lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5754
__timer_delete_sync+0x148/0x310 kernel/time/timer.c:1648
del_timer_sync include/linux/timer.h:185 [inline]
hsr_dellink+0x33/0x80 net/hsr/hsr_netlink.c:132
default_device_exit_batch+0x956/0xa90 net/core/dev.c:11737
ops_exit_list net/core/net_namespace.c:175 [inline]
cleanup_net+0x89d/0xcc0 net/core/net_namespace.c:637
process_one_work kernel/workqueue.c:3254 [inline]
process_scheduled_works+0xa10/0x17c0 kernel/workqueue.c:3335
worker_thread+0x86d/0xd70 kernel/workqueue.c:3416
kthread+0x2f0/0x390 kernel/kthread.c:388
ret_from_fork+0x4b/0x80 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244
</TASK>
ODEBUG: assert_init not available (active state 0) object: ffff88806d3fcd88 object type: timer_list hint: 0x0
WARNING: CPU: 1 PID: 11 at lib/debugobjects.c:517 debug_print_object+0x17a/0x1f0 lib/debugobjects.c:514
Fixes: 5055cccfc2 ("net: hsr: Provide RedBox support (HSR-SAN)")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240426163355.2613767-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King says:
====================
net: dsa: microchip: use phylink_mac_ops for ksz driver
This four patch series switches the Microchip KSZ DSA driver to use
phylink_mac_ops support, and for this one we go a little further
beyond a simple conversion. This driver has four distinct cases:
lan937x
ksz9477
ksz8
ksz8830
Three of these cases are handled by shimming the existing DSA calls
through ksz_dev_ops, and the final case is handled through a
conditional in ksz_phylink_mac_config(). These can all be handled
with separate phylink_mac_ops.
To get there, we do a progressive conversion.
Patch 1 removes ksz_dev_ops' phylink_mac_config() method which is
not populated in any of the arrays - and is thus redundant.
Patch 2 switches the driver to use a common set of phylink_mac_ops
for all cases, doing the simple conversion to avoid the DSA shim.
Patch 3 pushes the phylink_mac_ops down to the first three classes
(lan937x, ksz9477, ksz8) adding an appropriate pointer to the
phylink_mac_ops to struct ksz_chip_data, and using that to
populate DSA's ds->phylink_mac_ops pointer. The difference between
each of these are the mac_link_up() method. mac_config() and
mac_link_down() remain common between each at this stage.
Patch 4 splits out ksz8830, which needs different mac_config()
handling, and thus means we have a difference in mac_config()
methods between the now four phylink_mac_ops structures.
Build tested only, with additional -Wunused-const-variable flag.
====================
Link: https://lore.kernel.org/r/ZivP/R1IwKEPb5T6@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert ksz_common to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1s0O7H-009gpq-IF@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phylink_mac_config function pointer member of struct ksz_dev_ops is
never initialised, so let's remove it to simplify the code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1s0O7C-009gpk-Dh@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 47ea0ddb1f ("platform/chrome: cros_ec_lpc: Separate host
command and irq disable") re-ordered the resume sequence. Before that
change, cros_ec resume sequence is:
1) Enable IRQ
2) Send resume event
3) Handle events during suspend
After commit 47ea0ddb1f ("platform/chrome: cros_ec_lpc: Separate host
command and irq disable"), cros_ec resume sequence is:
1) Enable IRQ
2) Handle events during suspend
3) Send resume event.
This re-ordering leads to delayed handling of any events queued between
items 2) and 3) with the updated sequence. Also in certain platforms, EC
skips triggering interrupt for certain events eg. mkbp events until the
resume event is received. Such events are stuck in the host event queue
indefinitely. This change puts back the original order to avoid any
delay in handling the pending events.
Fixes: 47ea0ddb1f ("platform/chrome: cros_ec_lpc: Separate host command and irq disable")
Cc: <stable@vger.kernel.org>
Cc: Lalith Rajendran <lalithkraj@chromium.org>
Cc: <chrome-platform@lists.linux.dev>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@chromium.org>
Link: https://lore.kernel.org/r/20240429121343.v2.1.If2e0cef959f1f6df9f4d1ab53a97c54aa54208af@changeid
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Commit f316cdff8d ("clk: Annotate struct clk_hw_onecell_data with
__counted_by") annotated the hws member of 'struct clk_hw_onecell_data'
with __counted_by, which informs the bounds sanitizer about the number
of elements in hws, so that it can warn when hws is accessed out of
bounds. As noted in that change, the __counted_by member must be
initialized with the number of elements before the first array access
happens, otherwise there will be a warning from each access prior to the
initialization because the number of elements is zero. This occurs in
raspberrypi_discover_clocks() due to ->num being assigned after ->hws
has been accessed:
UBSAN: array-index-out-of-bounds in drivers/clk/bcm/clk-raspberrypi.c:374:4
index 3 is out of range for type 'struct clk_hw *[] __counted_by(num)' (aka 'struct clk_hw *[]')
Move the ->num initialization to before the first access of ->hws, which
clears up the warning.
Cc: stable@vger.kernel.org
Fixes: f316cdff8d ("clk: Annotate struct clk_hw_onecell_data with __counted_by")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240425-cbl-bcm-assign-counted-by-val-before-access-v1-2-e2db3b82d5ef@kernel.org
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Commit f316cdff8d ("clk: Annotate struct clk_hw_onecell_data with
__counted_by") annotated the hws member of 'struct clk_hw_onecell_data'
with __counted_by, which informs the bounds sanitizer about the number
of elements in hws, so that it can warn when hws is accessed out of
bounds. As noted in that change, the __counted_by member must be
initialized with the number of elements before the first array access
happens, otherwise there will be a warning from each access prior to the
initialization because the number of elements is zero. This occurs in
clk_dvp_probe() due to ->num being assigned after ->hws has been
accessed:
UBSAN: array-index-out-of-bounds in drivers/clk/bcm/clk-bcm2711-dvp.c:59:2
index 0 is out of range for type 'struct clk_hw *[] __counted_by(num)' (aka 'struct clk_hw *[]')
Move the ->num initialization to before the first access of ->hws, which
clears up the warning.
Cc: stable@vger.kernel.org
Fixes: f316cdff8d ("clk: Annotate struct clk_hw_onecell_data with __counted_by")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20240425-cbl-bcm-assign-counted-by-val-before-access-v1-1-e2db3b82d5ef@kernel.org
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Miscellaneous fixes and improvements.
- Add SPI (MSIOF) and external interrupt (INTC-EX) clocks on R-Car
V4M,
- Add interrupt controller (PLIC) clock and reset on RZ/Five,
- Prepare power domain support for RZ/G2L family members, and add
actual support on RZ/G3S SoC.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCZitbAgAKCRCKwlD9ZEnx
cOv3AQCeITT+A5qog/T6uzT62sg04KTLSvuwbg/zKWaWZHVjMwEAlYF3OOw4UgBT
AvVQPfm6dth8xtmWdLT0ulPD5XYq7gc=
=mTx5
-----END PGP SIGNATURE-----
Merge tag 'renesas-clk-for-v6.10-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-renesas
Pull more Renesas clk driver updates from Geert Uytterhoeven:
- Miscellaneous fixes and improvements
- Add SPI (MSIOF) and external interrupt (INTC-EX) clocks on R-Car V4M
- Add interrupt controller (PLIC) clock and reset on RZ/Five
- Prepare power domain support for RZ/G2L family members, and add
actual support on RZ/G3S SoC
* tag 'renesas-clk-for-v6.10-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r9a08g045: Add support for power domains
clk: renesas: rzg2l: Extend power domain support
dt-bindings: clock: renesas,rzg2l-cpg: Update #power-domain-cells = <1> for RZ/G3S
dt-bindings: clock: r9a08g045-cpg: Add power domain IDs
dt-bindings: clock: r9a07g054-cpg: Add power domain IDs
dt-bindings: clock: r9a07g044-cpg: Add power domain IDs
dt-bindings: clock: r9a07g043-cpg: Add power domain IDs
clk: renesas: shmobile: Remove unused CLK_ENABLE_ON_INIT
clk: renesas: r8a7740: Remove unused div4_clk.flags field
clk: renesas: r9a07g043: Add clock and reset entry for PLIC
clk: renesas: r8a779h0: Add INTC-EX clock
clk: renesas: r8a779h0: Add MSIOF clocks
clk: renesas: r8a779a0: Fix CANFD parent clock
Add a selftests validating that it's possible to have some struct_ops
callback set declaratively, then disable it (by setting to NULL)
programmatically. Libbpf should detect that such program should
not be loaded. Otherwise, it will unnecessarily fail the loading
when the host kernel does not have the type information.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20240428030954.3918764-2-andrii@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
If struct_ops has one of program callbacks set declaratively and host
kernel is old and doesn't support this callback, libbpf will allow to
load such struct_ops as long as that callback was explicitly nulled-out
(presumably through skeleton). This is all working correctly, except we
won't reset corresponding program slot to NULL before bailing out, which
will lead to libbpf not detecting that BPF program has to be not
auto-loaded. Fix this by unconditionally resetting corresponding program
slot to NULL.
Fixes: c911fc61a7 ("libbpf: Skip zeroed or null fields if not found in the kernel type.")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20240428030954.3918764-1-andrii@kernel.org
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Inclusion of the header linux/btf_ids.h relies on indirect inclusion of
the header linux/types.h. Including it directly on the top level helps
to avoid potential problems if linux/types.h hasn't been included
before.
The main motivation to introduce this it is to avoid similar problems that
have shown up in the bpftool where GNU libc indirectly pulls
linux/types.h causing compile error of the form:
error: unknown type name 'u32'
u32 cnt;
^~~
The bpftool compile error was fixed in
62248b22d0 ("tools/resolve_btfids: fix build with musl libc").
Signed-off-by: Dmitrii Bundin <dmitrii.bundin.a@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240420042457.3198883-1-dmitrii.bundin.a@gmail.com
The strdup() function returns a pointer to a new string which is a
duplicate of the string "input". Memory for the new string is obtained
with malloc(), and need to be freed with free().
This patch adds these missing "free(input)" in parse_stats() to avoid
memory leak in veristat.c.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/ded44f8865cd7f337f52fc5fb0a5fbed7d6bd641.1714374022.git.tanggeliang@kylinos.cn
The strdup() function returns a pointer to a new string which is a
duplicate of the string "ptr". Memory for the new string is obtained
with malloc(), and need to be freed with free().
This patch adds these missing "free(ptr)" in check_whitelist() and
check_blacklist() to avoid memory leaks in test_sockmap.c.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/b76f2f4c550aebe4ab8ea73d23c4cbe4f06ea996.1714374022.git.tanggeliang@kylinos.cn
The cgroup1_hierarchy test uses setup_classid_environment to setup
cgroupv1 environment. The problem is that the environment is set in
/sys/fs/cgroup and therefore, if not run under an own mount namespace,
effectively deletes all system cgroups:
$ ls /sys/fs/cgroup | wc -l
27
$ sudo ./test_progs -t cgroup1_hierarchy
#41/1 cgroup1_hierarchy/test_cgroup1_hierarchy:OK
#41/2 cgroup1_hierarchy/test_root_cgid:OK
#41/3 cgroup1_hierarchy/test_invalid_level:OK
#41/4 cgroup1_hierarchy/test_invalid_cgid:OK
#41/5 cgroup1_hierarchy/test_invalid_hid:OK
#41/6 cgroup1_hierarchy/test_invalid_cgrp_name:OK
#41/7 cgroup1_hierarchy/test_invalid_cgrp_name2:OK
#41/8 cgroup1_hierarchy/test_sleepable_prog:OK
#41 cgroup1_hierarchy:OK
Summary: 1/8 PASSED, 0 SKIPPED, 0 FAILED
$ ls /sys/fs/cgroup | wc -l
1
To avoid this, run setup_cgroup_environment first which will create an
own mount namespace. This only affects the cgroupv1_hierarchy test as
all other cgroup1 test progs already run setup_cgroup_environment prior
to running setup_classid_environment.
Also add a comment to the header of setup_classid_environment to warn
against this invalid usage in future.
Fixes: 360769233c ("selftests/bpf: Add selftests for cgroup1 hierarchy")
Signed-off-by: Viktor Malik <vmalik@redhat.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240429112311.402497-1-vmalik@redhat.com
Let the krealloc_array() copy the original data and
check for a multiplication overflow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/bpf/20240429120005.3539116-1-andriy.shevchenko@linux.intel.com
Use struct_size() instead of hand writing it.
This is less verbose and more robust.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yonghong.song@linux.dev>
Link: https://lore.kernel.org/bpf/20240429121323.3818497-1-andriy.shevchenko@linux.intel.com
When I use the command 'make M=samples/bpf' to compile samples/bpf code
in ubuntu 22.04, the error info occured:
Cannot find a vmlinux for VMLINUX_BTF at any of " /home/ubuntu/code/linux/vmlinux",
build the kernel or set VMLINUX_BTF or VMLINUX_H variable
Others often encounter this kind of issue, new kernel has the vmlinux, so we can
set the path in error info which seems more intuitive, like:
Cannot find a vmlinux for VMLINUX_BTF at any of " /home/ubuntu/code/linux/vmlinux",
buiild the kernel or set VMLINUX_BTF like "VMLINUX_BTF=/sys/kernel/btf/vmlinux" or
VMLINUX_H variable
Signed-off-by: Tao Chen <chen.dylane@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20240428161032.239043-1-chen.dylane@gmail.com
Two doc update patches and the following three fixes:
- On single node systems, the default pool is used but the node_nr_active
for the default pool was set to min_active. This effectively limited the
max concurrency of unbound pools on single node systems to 8 causing
performance regressions on some workloads. Fixed by setting the default
pool's node_nr_active to max_active.
- wq_update_node_max_active() could trigger divide-by-zero if the
intersection between the allowed CPUs for an unbound workqueue and online
CPUs becomes empty.
- When kick_pool() was trying to repatriate a worker to a CPU in its pod by
setting task->wake_cpu, it didn't consider whether the CPU being selected
is online or not which obviously can lead to subobtimal behaviors. On
s390, this triggered a crash in arch code. The workqueue patch removes the
gross misbehavior but doesn't fix the crash completely as there's a race
window in which CPUs can go down after wake_cpu is set. Need to decide
whether the fix should be on the core or arch side.
-----BEGIN PGP SIGNATURE-----
iIQEABYKACwWIQTfIjM1kS57o3GsC/uxYfJx3gVYGQUCZjAaug4cdGpAa2VybmVs
Lm9yZwAKCRCxYfJx3gVYGT4fAQC5d8dNCDrAJmMgI0OBCwVgGGISTPalI+/ix4zu
5muBLwEAszuSZ4hEmg4L/jseTk+gZV0vIi4/IHjOzWwYczzLxQA=
=SeX1
-----END PGP SIGNATURE-----
Merge tag 'wq-for-6.9-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fixes from Tejun Heo:
"Two doc update patches and the following three fixes:
- On single node systems, the default pool is used but the
node_nr_active for the default pool was set to min_active. This
effectively limited the max concurrency of unbound pools on single
node systems to 8 causing performance regressions on some
workloads. Fixed by setting the default pool's node_nr_active to
max_active.
- wq_update_node_max_active() could trigger divide-by-zero if the
intersection between the allowed CPUs for an unbound workqueue and
online CPUs becomes empty.
- When kick_pool() was trying to repatriate a worker to a CPU in its
pod by setting task->wake_cpu, it didn't consider whether the CPU
being selected is online or not which obviously can lead to
subobtimal behaviors. On s390, this triggered a crash in arch code.
The workqueue patch removes the gross misbehavior but doesn't fix
the crash completely as there's a race window in which CPUs can go
down after wake_cpu is set. Need to decide whether the fix should
be on the core or arch side"
* tag 'wq-for-6.9-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Fix divide error in wq_update_node_max_active()
workqueue: The default node_nr_active should have its max set to max_active
workqueue: Fix selection of wake_cpu in kick_pool()
docs/zh_CN: core-api: Update translation of workqueue.rst to 6.9-rc1
Documentation/core-api: Update events_freezable_power references.
With posted MSI feature enabled on the CPU side, iommu interrupt
remapping table entries (IRTEs) for device MSI/x can be allocated,
activated, and programed in posted mode. This means that IRTEs are
linked with their respective PIDs of the target CPU.
Handlers for the posted MSI notification vector will de-multiplex
device MSI handlers. CPU notifications are coalesced if interrupts
arrive at a high frequency.
Posted interrupts are only used for device MSI and not for legacy devices
(IO/APIC, HPET).
Introduce a new irq_chip for posted MSIs, which has a dummy irq_ack()
callback as EOI is performed in the notification handler once.
When posted MSI is enabled, MSI domain/chip hierarchy will look like
this example:
domain: IR-PCI-MSIX-0000:50:00.0-12
hwirq: 0x29
chip: IR-PCI-MSIX-0000:50:00.0
flags: 0x430
IRQCHIP_SKIP_SET_WAKE
IRQCHIP_ONESHOT_SAFE
parent:
domain: INTEL-IR-10-13
hwirq: 0x2d0000
chip: INTEL-IR-POST
flags: 0x0
parent:
domain: VECTOR
hwirq: 0x77
chip: APIC
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240423174114.526704-13-jacob.jun.pan@linux.intel.com
Add a command line opt-in option for posted MSI if CONFIG_X86_POSTED_MSI=y.
Also introduce a helper function for testing if posted MSI is supported on
the platform.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240423174114.526704-12-jacob.jun.pan@linux.intel.com
During interrupt affinity change, it is possible to have interrupts delivered
to the old CPU after the affinity has changed to the new one. To prevent lost
interrupts, local APIC IRR is checked on the old CPU. Similar checks must be
done for posted MSIs given the same reason.
Consider the following scenario:
Device system agent iommu memory CPU/LAPIC
1 FEEX_XXXX
2 Interrupt request
3 Fetch IRTE ->
4 ->Atomic Swap PID.PIR(vec)
Push to Global Observable(GO)
5 if (ON*)
done;*
else
6 send a notification ->
* ON: outstanding notification, 1 will suppress new notifications
If the affinity change happens between 3 and 5 in the IOMMU, the old CPU's
posted interrupt request (PIR) could have the pending bit set for the
vector being moved.
Add a helper function to check individual vector status. Then use the
helper to check for pending interrupts on the source CPU's PID.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240423174114.526704-11-jacob.jun.pan@linux.intel.com
Use a common function for checking pending interrupt vector in APIC IRR
instead of duplicated open coding them.
Additional checks for posted MSI vectors can then be contained in this
function.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240423174114.526704-10-jacob.jun.pan@linux.intel.com
All MSI vectors are multiplexed into a single notification vector when
posted MSI is enabled. It is the responsibility of the notification vector
handler to demultiplex MSI vectors. In the handler the MSI vector handlers
are dispatched without IDT delivery for each pending MSI interrupt.
For example, the interrupt flow will change as follows:
(3 MSIs of different vectors arrive in a a high frequency burst)
BEFORE:
interrupt(MSI)
irq_enter()
handler() /* EOI */
irq_exit()
process_softirq()
interrupt(MSI)
irq_enter()
handler() /* EOI */
irq_exit()
process_softirq()
interrupt(MSI)
irq_enter()
handler() /* EOI */
irq_exit()
process_softirq()
AFTER:
interrupt /* Posted MSI notification vector */
irq_enter()
atomic_xchg(PIR)
handler()
handler()
handler()
pi_clear_on()
apic_eoi()
irq_exit()
process_softirq()
Except for the leading MSI, CPU notifications are skipped/coalesced.
For MSIs which arrive at a low frequency, the demultiplexing loop does not
wait for more interrupts to coalesce. Therefore, there's no additional
latency other than the processing time.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240423174114.526704-9-jacob.jun.pan@linux.intel.com
Prepare for calling external interrupt handlers directly from the posted
MSI demultiplexing loop. Extract the common code from common_interrupt() to
avoid code duplication.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240423174114.526704-8-jacob.jun.pan@linux.intel.com
To support posted MSIs, create a posted interrupt descriptor (PID) for each
host CPU. Later on, when setting up interrupt affinity, the IOMMU's
interrupt remapping table entry (IRTE) will point to the physical address
of the matching CPU's PID.
Each PID is initialized with the owner CPU's physical APICID as the
destination.
Originally-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240423174114.526704-7-jacob.jun.pan@linux.intel.com
When posted MSI is enabled, all device MSIs are multiplexed into a single
notification vector. MSI handlers will be de-multiplexed at run-time by
system software without IDT delivery.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240423174114.526704-6-jacob.jun.pan@linux.intel.com
Make the PIR field into u64 such that atomic xchg64 can be used without
ugly casting.
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240423174114.526704-3-jacob.jun.pan@linux.intel.com
To prepare native usage of posted interrupts, move the PID declarations out
of VMX code such that they can be shared.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/r/20240423174114.526704-2-jacob.jun.pan@linux.intel.com
When doing
make menuconfig
and searching for the CLOCKSOURCE_WATCHDOG_MAX_SKEW_US config item, the
help says:
│ Symbol: CLOCKSOURCE_WATCHDOG_MAX_SKEW_US [=125]
│ Type : integer
│ Range : [50 1000]
│ Defined at kernel/time/Kconfig:204
│ Prompt: Clocksource watchdog maximum allowable skew (in s)
^^^
│ Depends on: GENERIC_CLOCKEVENTS [=y] && CLOCKSOURCE_WATCHDOG [=y]
because on some terminals, it cannot display the 'μ' char, unicode
number 0x3bc.
So simply write it out so that there's no trouble.
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@kernel.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20240428102143.26764-1-bp@kernel.org
- set A64 MIPI PLL min & max rate
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQSPRixG1tysKC2PKM10Ba7+DO8kkwUCZivU7QAKCRB0Ba7+DO8k
k7FxAQCmqRmRyqdz156D2XlrEi0/NJKXicCnzwgLhP/HT06r+QEA6H5fqrFNcSLB
p1iT0AMcXacdNNni+lz2i8Q6bAOjjwg=
=G9dC
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-fixes-for-6.9-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Pull Allwinner clk driver fixes from Jernej Skrabec:
- fix H6 CPU rate change via reparenting
- set A64 MIPI PLL min & max rate
* tag 'sunxi-clk-fixes-for-6.9-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: a64: Set minimum and maximum rate for PLL-MIPI
clk: sunxi-ng: common: Support minimum and maximum rate
clk: sunxi-ng: h6: Reparent CPUX during PLL CPUX rate change