[ Upstream commit cd7f7328d6 ]
Move ktime_get_snapshot() into the loop. If a retry does occur, a more
recent snapshot will result in a more accurate cross-timestamp.
Fixes: a90ec84837 ("igc: Add support for PTP getcrosststamp()")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com>
Reviewed-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e404ad95d ]
Writing to clear the PTM status 'valid' bit while the PTM cycle is
triggered results in unreliable PTM operation. To fix this, clear the
PTM 'trigger' and status after each PTM transaction.
The issue can be reproduced with the following:
$ sudo phc2sys -R 1000 -O 0 -i tsn0 -m
Note: 1000 Hz (-R 1000) is unrealistically large, but provides a way to
quickly reproduce the issue.
PHC2SYS exits with:
"ioctl PTP_OFFSET_PRECISE: Connection timed out" when the PTM transaction
fails
This patch also fixes a hang in igc_probe() when loading the igc
driver in the kdump kernel on systems supporting PTM.
The igc driver running in the base kernel enables PTM trigger in
igc_probe(). Therefore the driver is always in PTM trigger mode,
except in brief periods when manually triggering a PTM cycle.
When a crash occurs, the NIC is reset while PTM trigger is enabled.
Due to a hardware problem, the NIC is subsequently in a bad busmaster
state and doesn't handle register reads/writes. When running
igc_probe() in the kdump kernel, the first register access to a NIC
register hangs driver probing and ultimately breaks kdump.
With this patch, igc has PTM trigger disabled most of the time,
and the trigger is only enabled for very brief (10 - 100 us) periods
when manually triggering a PTM cycle. Chances that a crash occurs
during a PTM trigger are not 0, but extremely reduced.
Fixes: a90ec84837 ("igc: Add support for PTP getcrosststamp()")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Christopher S M Hall <christopher.s.hall@intel.com>
Reviewed-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Corinna Vinschen <vinschen@redhat.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0937cb5f34 ]
This reverts commit a104042e2b.
Since the original bug seems to have been around for years,
but a new issue was report with the fix, revert the fix for
now. We have a couple of weeks to figure it out for this
release, if needed.
Reported-by: Bert Karwatzki <spasswolf@web.de>
Closes: https://lore.kernel.org/linux-wireless/20250410215527.3001-1-spasswolf@web.de
Fixes: a104042e2b ("wifi: mac80211: Update skb's control block key in ieee80211_tx_dequeue()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 324dddea32 ]
The btrtl_initialize() function checks that rtl_load_file() either
had an error or it loaded a zero length file. However, if it loaded
a zero length file then the error code is not set correctly. It
results in an error pointer vs NULL bug, followed by a NULL pointer
dereference. This was detected by Smatch:
drivers/bluetooth/btrtl.c:592 btrtl_initialize() warn: passing zero to 'ERR_PTR'
Fixes: 26503ad25d ("Bluetooth: btrtl: split the device initialization into smaller parts")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eb73b5a915 ]
This fixes sending MGMT_EV_DEVICE_FOUND for invalid address
(00:00:00:00:00:00) which is a regression introduced by
a2ec905d1e ("Bluetooth: fix kernel oops in store_pending_adv_report")
since in the attempt to skip storing data for extended advertisement it
actually made the code to skip the entire if statement supposed to send
MGMT_EV_DEVICE_FOUND without attempting to use the last_addr_adv which
is garanteed to be invalid for extended advertisement since we never
store anything on it.
Link: https://github.com/bluez/bluez/issues/1157
Link: https://github.com/bluez/bluez/issues/1149#issuecomment-2767215658
Fixes: a2ec905d1e ("Bluetooth: fix kernel oops in store_pending_adv_report")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9beb2c91fb ]
Set maximum DMA segment size to 2G instead of UINT_MAX due to HW limit.
Fixes: e0477b34d9 ("RDMA: Explicitly pass in the dma_device to ib_register_device")
Link: https://patch.msgid.link/r/20250327114724.3454268-3-huangjunxian6@hisilicon.com
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ec1f02394 ]
The bitmap_get_stats() function incorrectly returns -ENOENT for external
bitmaps.
Remove the external bitmap check as the statistics should be available
regardless of bitmap storage location.
Return -EINVAL only for invalid bitmap with no storage (neither in
superblock nor in external file).
Note: "bitmap_info.external" here refers to a bitmap stored in a separate
file (bitmap_file), not to external metadata.
Fixes: 8d28d0ddb9 ("md/md-bitmap: Synchronize bitmap_get_stats() with bitmap lifetime")
Signed-off-by: Zheng Qixing <zhengqixing@huawei.com>
Link: https://lore.kernel.org/linux-raid/20250403015322.2873369-1-zhengqixing@huaweicloud.com
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 72eea84a10 ]
Add goto to ensure scsi_host_put() is called in all error paths of
iscsi_set_host_param() function. This fixes a potential memory leak when
strlen() check fails.
Fixes: ce51c81700 ("scsi: iscsi: Add strlen() check in iscsi_if_set{_host}_param()")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20250318094344.91776-1-linmq006@gmail.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0f0dc96de ]
The skb dequeued from tx_queue is lost when wl1251_ps_elp_wakeup fails
with a -ETIMEDOUT error. Fix that by queueing the skb back to tx_queue.
Fixes: c5483b7193 ("wl12xx: check if elp wakeup failed")
Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com>
Reviewed-by: Michael Nemanov <michael.nemanov@ti.com>
Link: https://patch.msgid.link/20250330104532.44935-1-abdun.nihaal@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a104042e2b ]
The ieee80211 skb control block key (set when skb was queued) could have
been removed before ieee80211_tx_dequeue() call. ieee80211_tx_dequeue()
already called ieee80211_tx_h_select_key() to get the current key, but
the latter do not update the key in skb control block in case it is
NULL. Because some drivers actually use this key in their TX callbacks
(e.g. ath1{1,2}k_mac_op_tx()) this could lead to the use after free
below:
BUG: KASAN: slab-use-after-free in ath11k_mac_op_tx+0x590/0x61c
Read of size 4 at addr ffffff803083c248 by task kworker/u16:4/1440
CPU: 3 UID: 0 PID: 1440 Comm: kworker/u16:4 Not tainted 6.13.0-ge128f627f404 #2
Hardware name: HW (DT)
Workqueue: bat_events batadv_send_outstanding_bcast_packet
Call trace:
show_stack+0x14/0x1c (C)
dump_stack_lvl+0x58/0x74
print_report+0x164/0x4c0
kasan_report+0xac/0xe8
__asan_report_load4_noabort+0x1c/0x24
ath11k_mac_op_tx+0x590/0x61c
ieee80211_handle_wake_tx_queue+0x12c/0x1c8
ieee80211_queue_skb+0xdcc/0x1b4c
ieee80211_tx+0x1ec/0x2bc
ieee80211_xmit+0x224/0x324
__ieee80211_subif_start_xmit+0x85c/0xcf8
ieee80211_subif_start_xmit+0xc0/0xec4
dev_hard_start_xmit+0xf4/0x28c
__dev_queue_xmit+0x6ac/0x318c
batadv_send_skb_packet+0x38c/0x4b0
batadv_send_outstanding_bcast_packet+0x110/0x328
process_one_work+0x578/0xc10
worker_thread+0x4bc/0xc7c
kthread+0x2f8/0x380
ret_from_fork+0x10/0x20
Allocated by task 1906:
kasan_save_stack+0x28/0x4c
kasan_save_track+0x1c/0x40
kasan_save_alloc_info+0x3c/0x4c
__kasan_kmalloc+0xac/0xb0
__kmalloc_noprof+0x1b4/0x380
ieee80211_key_alloc+0x3c/0xb64
ieee80211_add_key+0x1b4/0x71c
nl80211_new_key+0x2b4/0x5d8
genl_family_rcv_msg_doit+0x198/0x240
<...>
Freed by task 1494:
kasan_save_stack+0x28/0x4c
kasan_save_track+0x1c/0x40
kasan_save_free_info+0x48/0x94
__kasan_slab_free+0x48/0x60
kfree+0xc8/0x31c
kfree_sensitive+0x70/0x80
ieee80211_key_free_common+0x10c/0x174
ieee80211_free_keys+0x188/0x46c
ieee80211_stop_mesh+0x70/0x2cc
ieee80211_leave_mesh+0x1c/0x60
cfg80211_leave_mesh+0xe0/0x280
cfg80211_leave+0x1e0/0x244
<...>
Reset SKB control block key before calling ieee80211_tx_h_select_key()
to avoid that.
Fixes: bb42f2d13f ("mac80211: Move reorder-sensitive TX handlers to after TXQ dequeue")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Link: https://patch.msgid.link/06aa507b853ca385ceded81c18b0a6dd0f081bc8.1742833382.git.repk@triplefau.lt
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27c7e63b3c ]
The memory pointed to by priv is freed at the end of at76_delete_device
function (using ieee80211_free_hw). But the code then accesses the udev
field of the freed object to put the USB device. This may also lead to a
memory leak of the usb device. Fix this by using udev from interface.
Fixes: 29e20aa6c6 ("at76c50x-usb: fix use after free on failure path in at76_probe()")
Signed-off-by: Abdun Nihaal <abdun.nihaal@gmail.com>
Link: https://patch.msgid.link/20250330103110.44080-1-abdun.nihaal@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8aa580cd92 ]
when a SATA disk is directly connected the SAS controller determines the
disk to which I/Os are delivered based on the port ID in the DQ entry.
When many phys are disconnected and reconnect, the port ID of phys were
changed and used by other link, resulting in I/O being sent to incorrect
disk. Data inconsistency on the SATA disk may occur during I/O retries
using the old port ID. So enable force phy, then force the command to be
executed in a certain phy, and if the actual phy ID of the port does not
match the phy configured in the command, the chip will stop delivering the
I/O to disk.
Fixes: ce60689e12 ("scsi: hisi_sas: add v3 code to send ATA frame")
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Link: https://lore.kernel.org/r/20250312095135.3048379-2-yangxingui@huawei.com
Reviewed-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e3f88665a7 upstream.
In the ssi_protocol_probe() function, &ssi->work is bound with
ssip_xmit_work(), In ssip_pn_setup(), the ssip_pn_xmit() function
within the ssip_pn_ops structure is capable of starting the
work.
If we remove the module which will call ssi_protocol_remove()
to make a cleanup, it will free ssi through kfree(ssi),
while the work mentioned above will be used. The sequence
of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| ssip_xmit_work
ssi_protocol_remove |
kfree(ssi); |
| struct hsi_client *cl = ssi->cl;
| // use ssi
Fix it by ensuring that the work is canceled before proceeding
with the cleanup in ssi_protocol_remove().
Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240918120749.1730-1-kxwang23@m.fudan.edu.cn
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5df5dafc17 upstream.
Do not set 'HCI_UART_PROTO_READY' before call 'hci_uart_register_dev()'.
Possible race is when someone calls 'hci_tty_uart_close()' after this bit
is set, but 'hci_uart_register_dev()' wasn't done. This leads to access
to uninitialized fields. To fix it let's set this bit after device was
registered (as before patch c411c62cc133) and to fix previous problem let's
add one more bit in addition to 'HCI_UART_PROTO_READY' which allows to
perform power up without original bit set (pls see commit c411c62cc133).
Crash backtrace from syzbot report:
RIP: 0010:skb_queue_empty_lockless include/linux/skbuff.h:1887 [inline]
RIP: 0010:skb_queue_purge_reason+0x6d/0x140 net/core/skbuff.c:3936
Call Trace:
<TASK>
skb_queue_purge include/linux/skbuff.h:3364 [inline]
mrvl_close+0x2f/0x90 drivers/bluetooth/hci_mrvl.c:100
hci_uart_tty_close+0xb6/0x120 drivers/bluetooth/hci_ldisc.c:557
tty_ldisc_close drivers/tty/tty_ldisc.c:455 [inline]
tty_ldisc_kill+0x66/0xc0 drivers/tty/tty_ldisc.c:613
tty_ldisc_release+0xc9/0x120 drivers/tty/tty_ldisc.c:781
tty_release_struct+0x10/0x80 drivers/tty/tty_io.c:1690
tty_release+0x4ef/0x640 drivers/tty/tty_io.c:1861
__fput+0x86/0x2a0 fs/file_table.c:450
task_work_run+0x82/0xb0 kernel/task_work.c:239
resume_user_mode_work include/linux/resume_user_mode.h:50 [inline]
exit_to_user_mode_loop kernel/entry/common.c:114 [inline]
exit_to_user_mode_prepare include/linux/entry-common.h:329 [inline]
__syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline]
syscall_exit_to_user_mode+0xa3/0x1b0 kernel/entry/common.c:218
do_syscall_64+0x9a/0x190 arch/x86/entry/common.c:89
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reported-by: syzbot+683f8cb11b94b1824c77@syzkaller.appspotmail.com
Tested-by: syzbot+683f8cb11b94b1824c77@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-bluetooth/d159c57f-8490-4c26-79da-6ad3612c4a14@salutedevices.com/
Fixes: 366ceff495 ("Bluetooth: hci_uart: fix race during initialization")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f2f29da9f0 upstream.
While debugging kexec/hibernation hangs and crashes, it turned out that
the current implementation of e820__register_nosave_regions() suffers from
multiple serious issues:
- The end of last region is tracked by PFN, causing it to find holes
that aren't there if two consecutive subpage regions are present
- The nosave PFN ranges derived from holes are rounded out (instead of
rounded in) which makes it inconsistent with how explicitly reserved
regions are handled
Fix this by:
- Treating reserved regions as if they were holes, to ensure consistent
handling (rounding out nosave PFN ranges is more correct as the
kernel does not use partial pages)
- Tracking the end of the last RAM region by address instead of pages
to detect holes more precisely
These bugs appear to have been introduced about ~18 years ago with the very
first version of e820_mark_nosave_regions(), and its flawed assumptions were
carried forward uninterrupted through various waves of rewrites and renames.
[ mingo: Added Git archeology details, for kicks and giggles. ]
Fixes: e8eff5ac29 ("[PATCH] Make swsusp avoid memory holes and reserved memory regions on x86_64")
Reported-by: Roberto Ricci <io@r-ricci.it>
Tested-by: Roberto Ricci <io@r-ricci.it>
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Len Brown <len.brown@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250406-fix-e820-nosave-v3-1-f3787bc1ee1d@qtmlabs.xyz
Closes: https://lore.kernel.org/all/Z4WFjBVHpndct7br@desktop0a/
Signed-off-by: Myrrh Periwinkle <myrrhperiwinkle@qtmlabs.xyz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dd4f730b55 upstream.
When an attribute group is created with sysfs_create_group(), the
->sysfs_ops() callback is set to kobj_sysfs_ops, which sets the ->show()
and ->store() callbacks to kobj_attr_show() and kobj_attr_store()
respectively. These functions use container_of() to get the respective
callback from the passed attribute, meaning that these callbacks need to
be of the same type as the callbacks in 'struct kobj_attribute'.
However, ->show() and ->store() in the platform_profile driver are
defined for struct device_attribute with the help of DEVICE_ATTR_RO()
and DEVICE_ATTR_RW(), which results in a CFI violation when accessing
platform_profile or platform_profile_choices under /sys/firmware/acpi
because the types do not match:
CFI failure at kobj_attr_show+0x19/0x30 (target: platform_profile_choices_show+0x0/0x140; expected type: 0x7a69590c)
There is no functional issue from the type mismatch because the layout
of 'struct kobj_attribute' and 'struct device_attribute' are the same,
so the container_of() cast does not break anything aside from CFI.
Change the type of platform_profile_choices_show() and
platform_profile_{show,store}() to match the callbacks in
'struct kobj_attribute' and update the attribute variables to
match, which resolves the CFI violation.
Cc: All applicable <stable@vger.kernel.org>
Fixes: a2ff95e018 ("ACPI: platform: Add platform profile support")
Reported-by: John Rowley <lkml@johnrowley.me>
Closes: https://github.com/ClangBuiltLinux/linux/issues/2047
Tested-by: John Rowley <lkml@johnrowley.me>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://patch.msgid.link/20250210-acpi-platform_profile-fix-cfi-violation-v3-1-ed9e9901c33a@kernel.org
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[nathan: Fix conflicts in older stable branches]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5951389e5 upstream.
When comparing to the ARM list [1], it appears that several ARM cores
were missing from the lists in spectre_bhb_loop_affected(). Add them.
NOTE: for some of these cores it may not matter since other ways of
clearing the BHB may be used (like the CLRBHB instruction or ECBHB),
but it still seems good to have all the info from ARM's whitepaper
included.
[1] https://developer.arm.com/Arm%20Security%20Center/Spectre-BHB
Fixes: 558c303c97 ("arm64: Mitigate spectre style branch history side channels")
Cc: stable@vger.kernel.org
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: James Morse <james.morse@arm.com>
Link: https://lore.kernel.org/r/20250107120555.v4.5.I4a9a527e03f663040721c5401c41de587d015c82@changeid
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c183165f87 upstream.
The file descriptor 'fd_in' is opened when cfg_input is configured, but
not closed in main_loop(), this patch fixes it.
Fixes: 05be5e273c ("selftests: mptcp: add disconnect tests")
Cc: stable@vger.kernel.org
Co-developed-by: Cong Liu <liucong2@kylinos.cn>
Signed-off-by: Cong Liu <liucong2@kylinos.cn>
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20250328-net-mptcp-misc-fixes-6-15-v1-3-34161a482a7f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e225128c3f upstream.
When submitting the TLMM test driver, Bjorn reported that some of the test
cases are failing for GPIOs that not are backed by PDC (i.e. "non-wakeup"
GPIOs that are handled directly in pinctrl-msm). Basically, lingering
latched interrupt state is still being delivered at IRQ request time, e.g.:
ok 1 tlmm_test_silent_rising
tlmm_test_silent_falling: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 2 tlmm_test_silent_falling
tlmm_test_silent_low: ASSERTION FAILED at drivers/pinctrl/qcom/tlmm-test.c:178
Expected atomic_read(&priv->intr_count) == 0, but
atomic_read(&priv->intr_count) == 1 (0x1)
not ok 3 tlmm_test_silent_low
ok 4 tlmm_test_silent_high
Whether to report interrupts that came in while the IRQ was unclaimed
doesn't seem to be well-defined in the Linux IRQ API. However, looking
closer at these specific cases, we're actually reporting events that do not
match the interrupt type requested by the driver:
1. After "ok 1 tlmm_test_silent_rising", the GPIO is in low state and
configured for IRQF_TRIGGER_RISING.
2. (a) In preparation for "tlmm_test_silent_falling", the GPIO is switched
to high state. The rising interrupt gets latched.
(b) The GPIO is re-configured for IRQF_TRIGGER_FALLING, but the latched
interrupt isn't cleared.
(c) The IRQ handler is called for the latched interrupt, but there
wasn't any falling edge.
3. (a) For "tlmm_test_silent_low", the GPIO remains in high state.
(b) The GPIO is re-configured for IRQF_TRIGGER_LOW. This seems to
result in a phantom interrupt that gets latched.
(c) The IRQ handler is called for the latched interrupt, but the GPIO
isn't in low state.
4. (a) For "tlmm_test_silent_high", the GPIO is switched to low state.
(b) This doesn't result in a latched interrupt, because RAW_STATUS_EN
was cleared when masking the level-triggered interrupt.
Fix this by clearing the interrupt state whenever making any changes to the
interrupt configuration. This includes previously disabled interrupts, but
also any changes to interrupt polarity or detection type.
With this change, all 16 test cases are now passing for the non-wakeup
GPIOs in the TLMM.
Cc: stable@vger.kernel.org
Fixes: cf9d052aa6 ("pinctrl: qcom: Don't clear pending interrupts when enabling")
Reported-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Closes: https://lore.kernel.org/r/20250227-tlmm-test-v1-1-d18877b4a5db@oss.qualcomm.com/
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/20250312-pinctrl-msm-type-latch-v1-1-ce87c561d3d7@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1f2768b6a3 upstream.
If device_register(&child->dev) fails, call put_device() to explicitly
release child->dev, per the comment at device_register().
Found by code review.
Link: https://lore.kernel.org/r/20250202062357.872971-1-make24@iscas.ac.cn
Fixes: 4f535093cf ("PCI: Put pci_dev in device tree as early as possible")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2df181e1ae upstream.
A call to of_parse_phandle() is incrementing the refcount, and as such,
the of_node_put() must be called when the reference is no longer needed.
Thus, refactor the existing code and add a missing of_node_put() call
following the check to ensure that "msi_np" matches "pcie->np" and after
MSI initialization, but only if the MSI support is enabled system-wide.
Cc: stable@vger.kernel.org # v5.10+
Fixes: 40ca1bf580 ("PCI: brcmstb: Add MSI support")
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20250122222955.1752778-1-svarbanov@suse.de
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 708124d9e6 upstream.
of_irq_init() will leak interrupt controller device node refcounts
in two places as explained below:
1) Leak refcounts of both @desc->dev and @desc->interrupt_parent when
suffers @desc->irq_init_cb() failure.
2) Leak refcount of @desc->interrupt_parent when cleans up list
@intc_desc_list in the end.
Refcounts of both @desc->dev and @desc->interrupt_parent were got in
the first loop, but of_irq_init() does not put them before kfree(@desc)
in places mentioned above, so causes refcount leakages.
Fix by putting refcounts involved before kfree(@desc).
Fixes: 8363ccb917 ("of/irq: add missing of_node_put")
Fixes: c71a54b082 ("of/irq: introduce of_irq_init")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250209-of_irq_fix-v2-7-93e3a2659aa7@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 962a2805e4 upstream.
In irq_of_parse_and_map(), refcount of device node @oirq.np was got
by successful of_irq_parse_one() invocation, but it does not put the
refcount before return, so causes @oirq.np refcount leakage.
Fix by putting @oirq.np refcount before return.
Fixes: e387344499 ("of/irq: Move irq_of_parse_and_map() to common code")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250209-of_irq_fix-v2-6-93e3a2659aa7@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bbf71f44aa upstream.
of_irq_count() invokes of_irq_parse_one() to count IRQs, and successful
invocation of the later will get device node @irq.np refcount, but the
former does not put the refcount before next iteration invocation, hence
causes device node refcount leakages.
Fix by putting @irq.np refcount before the next iteration invocation.
Fixes: 3da5278727 ("of/irq: Rework of_irq_count()")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250209-of_irq_fix-v2-5-93e3a2659aa7@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff93e7213d upstream.
if the node @out_irq->np got by of_irq_parse_raw() is a combo node which
consists of both controller and nexus, namely, of_irq_parse_raw() returns
due to condition (@ipar == @newpar), then the node's refcount was increased
twice, hence causes refcount leakage.
Fix by putting @out_irq->np refcount before returning due to the condition.
Also add comments about refcount of node @out_irq->np got by the API.
Fixes: 0412841812 ("of/irq: Allow matching of an interrupt-map local to an interrupt controller")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250209-of_irq_fix-v2-4-93e3a2659aa7@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0cb58d6c7b upstream.
of_irq_parse_one(@int_gen_dev, i, ...) will leak refcount of @i_th_phandle
int_gen_dev {
...
interrupts-extended = ..., <&i_th_phandle ...>, ...;
...
};
Refcount of @i_th_phandle is increased by of_parse_phandle_with_args()
but is not decreased by API of_irq_parse_one() before return, so causes
refcount leakage.
Rework the refcounting to use __free() cleanup and simplify the code to
have a single call to of_irq_parse_raw().
Also add comments about refcount of node @out_irq->np got by the API.
Fixes: 79d9701559 ("of/irq: create interrupts-extended property")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20250209-of_irq_fix-v2-2-93e3a2659aa7@quicinc.com
[robh: Use __free() to do puts]
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd5625fc86 upstream.
msi_db_mask is of type 'u64', still the standard 'int' arithmetic is
performed to compute its value.
While most of the ntb_hw drivers actually don't utilize the higher 32
bits of the doorbell mask now, this may be the case for Switchtec - see
switchtec_ntb_init_db().
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
Fixes: 2b0569b3b7 ("NTB: Add MSI interrupt support to ntb_transport")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef01cac401 upstream.
Acquire a lock on kvm->srcu when userspace is getting MP state to handle a
rather extreme edge case where "accepting" APIC events, i.e. processing
pending INIT or SIPI, can trigger accesses to guest memory. If the vCPU
is in L2 with INIT *and* a TRIPLE_FAULT request pending, then getting MP
state will trigger a nested VM-Exit by way of ->check_nested_events(), and
emuating the nested VM-Exit can access guest memory.
The splat was originally hit by syzkaller on a Google-internal kernel, and
reproduced on an upstream kernel by hacking the triple_fault_event_test
selftest to stuff a pending INIT, store an MSR on VM-Exit (to generate a
memory access on VMX), and do vcpu_mp_state_get() to trigger the scenario.
=============================
WARNING: suspicious RCU usage
6.14.0-rc3-b112d356288b-vmx/pi_lockdep_false_pos-lock #3 Not tainted
-----------------------------
include/linux/kvm_host.h:1058 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by triple_fault_ev/1256:
#0: ffff88810df5a330 (&vcpu->mutex){+.+.}-{4:4}, at: kvm_vcpu_ioctl+0x8b/0x9a0 [kvm]
stack backtrace:
CPU: 11 UID: 1000 PID: 1256 Comm: triple_fault_ev Not tainted 6.14.0-rc3-b112d356288b-vmx #3
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Call Trace:
<TASK>
dump_stack_lvl+0x7f/0x90
lockdep_rcu_suspicious+0x144/0x190
kvm_vcpu_gfn_to_memslot+0x156/0x180 [kvm]
kvm_vcpu_read_guest+0x3e/0x90 [kvm]
read_and_check_msr_entry+0x2e/0x180 [kvm_intel]
__nested_vmx_vmexit+0x550/0xde0 [kvm_intel]
kvm_check_nested_events+0x1b/0x30 [kvm]
kvm_apic_accept_events+0x33/0x100 [kvm]
kvm_arch_vcpu_ioctl_get_mpstate+0x30/0x1d0 [kvm]
kvm_vcpu_ioctl+0x33e/0x9a0 [kvm]
__x64_sys_ioctl+0x8b/0xb0
do_syscall_64+0x6c/0x170
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-ID: <20250401150504.829812-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 15970e1b23 upstream.
When the tx tail is less than the head (in cases of wraparound), the TX
consumed descriptor statistic in DQ will be reported as
UINT32_MAX - head + tail, which is incorrect. Mask the difference of
head and tail according to the ring size when reporting the statistic.
Cc: stable@vger.kernel.org
Fixes: 2c9198356d ("gve: Add consumed counts to ethtool stats")
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250402001037.2717315-1-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8323f3a69d upstream.
When the Tegra186 GPIO controller is probed through ACPI matching,
the driver emits two error messages during probing:
"tegra186-gpio NVDA0508:00: invalid resource (null)"
"tegra186-gpio NVDA0508:00: invalid resource (null)"
Fix this by getting resource first and then do the ioremap.
Fixes: 2606e7c9f5 ("gpio: tegra186: Add ACPI support")
Cc: stable@vger.kernel.org
Signed-off-by: Guixin Liu <kanie@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250327032349.78809-1-kanie@linux.alibaba.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42ea22e754 upstream.
When the kernel contains a large number of functions that can be traced,
the loop in ftrace_graph_set_hash() may take a lot of time to execute.
This may trigger the softlockup watchdog.
Add cond_resched() within the loop to allow the kernel to remain
responsive even when processing a large number of functions.
This matches the cond_resched() that is used in other locations of the
code that iterates over all functions that can be traced.
Cc: stable@vger.kernel.org
Fixes: b9b0c831be ("ftrace: Convert graph filter to use hash tables")
Link: https://lore.kernel.org/tencent_3E06CE338692017B5809534B9C5C03DA7705@qq.com
Signed-off-by: zhoumin <teczm@foxmail.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2de510fccb upstream.
There's a possible race condition in dm-verity - the prefetch work item
may race with suspend and it is possible that prefetch continues to run
while the device is suspended. Fix this by calling flush_workqueue and
dm_bufio_client_reset in the postsuspend hook.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00204ae3d6 upstream.
The dm-integrity target didn't set the error string when memory
allocation failed. This patch fixes it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c56542878 upstream.
There's a possible race condition in dm-ebs - dm bufio prefetch may be in
progress while the device is suspended. Fix this by calling
dm_bufio_client_reset in the postsuspend hook.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 07bb097b92 upstream.
Currently, the ASP primary device check does not have support for PCI
domains, and, as a result, when the system is configured with PCI domains
(PCI segments) the wrong device can be selected as primary. This results
in commands submitted to the device timing out and failing. The device
check also relies on specific device and function assignments that may
not hold in the future.
Fix the primary ASP device check to include support for PCI domains and
to perform proper checking of the Bus/Device/Function positions.
Fixes: 2a6170dfe7 ("crypto: ccp: Add Platform Security Processor (PSP) device support")
Cc: stable@vger.kernel.org
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 25708f73ff upstream.
Enable the retain_ff_enable bit of GDSCR only if the GDSC is already ON.
Once the GDSCR moves to HW control, SW no longer can determine the state
of the GDSCR and setting the retain_ff bit could destroy all the register
contents we intended to save.
Therefore, move the retain_ff configuration before switching the GDSC to
HW trigger mode.
Cc: stable@vger.kernel.org
Fixes: 173722995c ("clk: qcom: gdsc: Add support to enable retention of GSDCR")
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Imran Shaik <quic_imrashai@quicinc.com>
Tested-by: Imran Shaik <quic_imrashai@quicinc.com> # on QCS8300
Link: https://lore.kernel.org/r/20250214-gdsc_fixes-v1-1-73e56d68a80f@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65a7334645 upstream.
Adding a new clause to this if/else I noticed the existing usage of
pm_genpd_add_subdomain() wasn't capturing and returning the result code.
pm_genpd_add_subdomain() returns an int and can fail. Capture that result
code and throw it up the call stack if something goes wrong.
Fixes: 1b771839de ("clk: qcom: gdsc: enable optional power domain support")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20250117-b4-linux-next-24-11-18-clock-multiple-power-domains-v10-2-13f2bb656dad@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e6dfde439 upstream.
gdsc_unregister() should release subdomains in the reverse order to the
order in which those subdomains were added.
I've made this patch a standalone patch because it facilitates a subsequent
fix to stable.
Fixes: 1b771839de ("clk: qcom: gdsc: enable optional power domain support")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20250117-b4-linux-next-24-11-18-clock-multiple-power-domains-v10-1-13f2bb656dad@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2510859475 upstream.
The echo_interval is not limited in any way during mounting,
which makes it possible to write a large number to it. This can
cause an overflow when multiplying ctx->echo_interval by HZ in
match_server().
Add constraints for echo_interval to smb3_fs_context_parse_param().
Found by Linux Verification Center (linuxtesting.org) with Svace.
Fixes: adfeb3e00e ("cifs: Make echo interval tunable")
Cc: stable@vger.kernel.org
Signed-off-by: Roman Smirnov <r.smirnov@omp.ru>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b4885bd593 upstream.
cifs_server_dbg() implies server to be non-NULL so
move call under condition to avoid NULL pointer dereference.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: e79b0332ae ("cifs: ignore cached share root handle closing errors")
Cc: stable@vger.kernel.org
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee022e5cae upstream.
The mapping table for the rk3328 is missing the entry for -25C which is
found in the TRM section 9.5.2 "Temperature-to-code mapping".
NOTE: the kernel uses the tsadc_q_sel=1'b1 mode which is defined as:
4096-<code in table>. Whereas the table in the TRM gives the code
"3774" for -25C, the kernel uses 4096-3774=322.
[Dragan Simic] : "After going through the RK3308 and RK3328 TRMs, as
well as through the downstream kernel code, it seems we may have
some troubles at our hands. Let me explain, please.
To sum it up, part 1 of the RK3308 TRM v1.1 says on page 538 that
the equation for the output when tsadc_q_sel equals 1 is (4096 -
tsadc_q), while part 1 of the RK3328 TRM v1.2 says that the output
equation is (1024 - tsadc_q) in that case.
The downstream kernel code, however, treats the RK3308 and RK3328
tables and their values as being the same. It even mentions 1024 as
the "offset" value in a comment block for the rk_tsadcv3_control()
function, just like the upstream code does, which is obviously wrong
"offset" value when correlated with the table on page 544 of part 1
of the RK3308 TRM v1.1.
With all this in mind, it's obvious that more work is needed to make
it clear where's the actual mistake (it could be that the TRM is
wrong), which I'll volunteer for as part of the SoC binning project.
In the meantime, this patch looks fine as-is to me, by offering
what's a clear improvement to the current state of the upstream
code"
Link: https://opensource.rock-chips.com/images/9/97/Rockchip_RK3328TRM_V1.1-Part1-20170321.pdf
Cc: stable@vger.kernel.org
Fixes: eda519d5f7 ("thermal: rockchip: Support the RK3328 SOC in thermal driver")
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20250207175048.35959-1-twoerner@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f1a69a940d upstream.
sctp_sendmsg() re-uses associations and transports when possible by
doing a lookup based on the socket endpoint and the message destination
address, and then sctp_sendmsg_to_asoc() sets the selected transport in
all the message chunks to be sent.
There's a possible race condition if another thread triggers the removal
of that selected transport, for instance, by explicitly unbinding an
address with setsockopt(SCTP_SOCKOPT_BINDX_REM), after the chunks have
been set up and before the message is sent. This can happen if the send
buffer is full, during the period when the sender thread temporarily
releases the socket lock in sctp_wait_for_sndbuf().
This causes the access to the transport data in
sctp_outq_select_transport(), when the association outqueue is flushed,
to result in a use-after-free read.
This change avoids this scenario by having sctp_transport_free() signal
the freeing of the transport, tagging it as "dead". In order to do this,
the patch restores the "dead" bit in struct sctp_transport, which was
removed in
commit 47faa1e4c5 ("sctp: remove the dead field of sctp_transport").
Then, in the scenario where the sender thread has released the socket
lock in sctp_wait_for_sndbuf(), the bit is checked again after
re-acquiring the socket lock to detect the deletion. This is done while
holding a reference to the transport to prevent it from being freed in
the process.
If the transport was deleted while the socket lock was relinquished,
sctp_sendmsg_to_asoc() will return -EAGAIN to let userspace retry the
send.
The bug was found by a private syzbot instance (see the error report [1]
and the C reproducer that triggers it [2]).
Link: https://people.igalia.com/rcn/kernel_logs/20250402__KASAN_slab-use-after-free_Read_in_sctp_outq_select_transport.txt [1]
Link: https://people.igalia.com/rcn/kernel_logs/20250402__KASAN_slab-use-after-free_Read_in_sctp_outq_select_transport__repro.c [2]
Cc: stable@vger.kernel.org
Fixes: df132eff46 ("sctp: clear the transport of some out_chunk_list chunks in sctp_assoc_rm_peer")
Suggested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Ricardo Cañuelo Navarro <rcn@igalia.com>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20250404-kasan_slab-use-after-free_read_in_sctp_outq_select_transport__20250404-v1-1-5ce4a0b78ef2@igalia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aaf99ac2ce upstream.
When an uncorrected memory error is consumed there is a race between the
CMCI from the memory controller reporting an uncorrected error with a UCNA
signature, and the core reporting and SRAR signature machine check when
the data is about to be consumed.
- Background: why *UN*corrected errors tied to *C*MCI in Intel platform [1]
Prior to Icelake memory controllers reported patrol scrub events that
detected a previously unseen uncorrected error in memory by signaling a
broadcast machine check with an SRAO (Software Recoverable Action
Optional) signature in the machine check bank. This was overkill because
it's not an urgent problem that no core is on the verge of consuming that
bad data. It's also found that multi SRAO UCE may cause nested MCE
interrupts and finally become an IERR.
Hence, Intel downgrades the machine check bank signature of patrol scrub
from SRAO to UCNA (Uncorrected, No Action required), and signal changed to
#CMCI. Just to add to the confusion, Linux does take an action (in
uc_decode_notifier()) to try to offline the page despite the UC*NA*
signature name.
- Background: why #CMCI and #MCE race when poison is consuming in Intel platform [1]
Having decided that CMCI/UCNA is the best action for patrol scrub errors,
the memory controller uses it for reads too. But the memory controller is
executing asynchronously from the core, and can't tell the difference
between a "real" read and a speculative read. So it will do CMCI/UCNA if
an error is found in any read.
Thus:
1) Core is clever and thinks address A is needed soon, issues a speculative read.
2) Core finds it is going to use address A soon after sending the read request
3) The CMCI from the memory controller is in a race with MCE from the core
that will soon try to retire the load from address A.
Quite often (because speculation has got better) the CMCI from the memory
controller is delivered before the core is committed to the instruction
reading address A, so the interrupt is taken, and Linux offlines the page
(marking it as poison).
- Why user process is killed for instr case
Commit 046545a661 ("mm/hwpoison: fix error page recovered but reported
"not recovered"") tries to fix noise message "Memory error not recovered"
and skips duplicate SIGBUSs due to the race. But it also introduced a bug
that kill_accessing_process() return -EHWPOISON for instr case, as result,
kill_me_maybe() send a SIGBUS to user process.
If the CMCI wins that race, the page is marked poisoned when
uc_decode_notifier() calls memory_failure(). For dirty pages,
memory_failure() invokes try_to_unmap() with the TTU_HWPOISON flag,
converting the PTE to a hwpoison entry. As a result,
kill_accessing_process():
- call walk_page_range() and return 1 regardless of whether
try_to_unmap() succeeds or fails,
- call kill_proc() to make sure a SIGBUS is sent
- return -EHWPOISON to indicate that SIGBUS is already sent to the
process and kill_me_maybe() doesn't have to send it again.
However, for clean pages, the TTU_HWPOISON flag is cleared, leaving the
PTE unchanged and not converted to a hwpoison entry. Conversely, for
clean pages where PTE entries are not marked as hwpoison,
kill_accessing_process() returns -EFAULT, causing kill_me_maybe() to send
a SIGBUS.
Console log looks like this:
Memory failure: 0x827ca68: corrupted page was clean: dropped without side effects
Memory failure: 0x827ca68: recovery action for clean LRU page: Recovered
Memory failure: 0x827ca68: already hardware poisoned
mce: Memory error not recovered
To fix it, return 0 for "corrupted page was clean", preventing an
unnecessary SIGBUS to user process.
[1] https://lore.kernel.org/lkml/20250217063335.22257-1-xueshuai@linux.alibaba.com/T/#mba94f1305b3009dd340ce4114d3221fe810d1871
Link: https://lkml.kernel.org/r/20250312112852.82415-3-xueshuai@linux.alibaba.com
Fixes: 046545a661 ("mm/hwpoison: fix error page recovered but reported "not recovered"")
Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Acked-by: Miaohe Lin <linmiaohe@huawei.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Borislav Betkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jane Chu <jane.chu@oracle.com>
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Naoya Horiguchi <nao.horiguchi@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ruidong Tian <tianruidong@linux.alibaba.com>
Cc: Thomas Gleinxer <tglx@linutronix.de>
Cc: Yazen Ghannam <yazen.ghannam@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0ebbb3841 upstream.
The PGDAT_RECLAIM_LOCKED bit is used to provide mutual exclusion of node
reclaim for struct pglist_data using a single bit.
It is "locked" with a test_and_set_bit (similarly to a try lock) which
provides full ordering with respect to loads and stores done within
__node_reclaim().
It is "unlocked" with clear_bit(), which does not provide any ordering
with respect to loads and stores done before clearing the bit.
The lack of clear_bit() memory ordering with respect to stores within
__node_reclaim() can cause a subsequent CPU to fail to observe stores from
a prior node reclaim. This is not an issue in practice on TSO (e.g.
x86), but it is an issue on weakly-ordered architectures (e.g. arm64).
Fix this by using clear_bit_unlock rather than clear_bit to clear
PGDAT_RECLAIM_LOCKED with a release memory ordering semantic.
This provides stronger memory ordering (release rather than relaxed).
Link: https://lkml.kernel.org/r/20250312141014.129725-1-mathieu.desnoyers@efficios.com
Fixes: d773ed6b85 ("mm: test and set zone reclaim lock before starting reclaim")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrea Parri <parri.andrea@gmail.com>
Cc: Will Deacon <will@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jade Alglave <j.alglave@ucl.ac.uk>
Cc: Luc Maranget <luc.maranget@inria.fr>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
