With phy-reset-gpios are enabled for i.MX8MM-EVK board, phy
will be reset. Without CONFIG_AT803X_PHY as y, board will stop
booting in NFS DHCP, because phy is not ready. So mark
CONFIG_AT803X_PHY from m to y to make board boot when using nfs rootfs.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GPIO handle is referencing the wrong GPIO, so the voltage did not
actually change as intended. The pinmux is already correct, so just
correct the GPIO number.
Fixes: 4a13b3bec3 (arm64: dts: imx: add Zii Ultra board support)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
vreg_lvs1a_1p8 and vreg_lvs2a_1p8 are both feeding pins in the low speed
connectors and should as such alway be on, so enable them.
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
SOC revision on older imx8mq is not available in fuses so on anything
other than B1 current code just reports "unknown".
TF-A already handles this by parsing the ROM and exposes the value
through a SMC call. Call this instead of reimplementing the workaround
in the kernel itself.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
drivers/isdn/hardware/mISDN/mISDNisar.c:30:17:
warning: faxmodulation_s defined but not used [-Wunused-const-variable=]
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a tracepoint in nfs_fh_to_dentry() for debugging issues with bad
userspace filehandles.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
If the server returns NFS4ERR_OLD_STATEID, then just skip retrying the
GETATTR when replaying the delegreturn compound. We know nothing will
have changed on the server.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
If the server returns NFS4ERR_OLD_STATEID in response to our delegreturn,
we want to sync to the most recent seqid for the delegation stateid. However
if we are already at the most recent, we have two possibilities:
- an OPEN reply is still outstanding and will return a new seqid
- an earlier OPEN reply was dropped on the floor due to a timeout.
In the latter case, we may end up unable to complete the delegreturn,
so we want to bump the seqid to a value greater than the cached value.
While this may cause us to lose the delegation in the former case,
it should now be safe to assume that the client will replay the OPEN
if necessary in order to get a new valid stateid.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
If the server returns the same delegation in an open that we just used
in a delegreturn, we need to ensure we don't apply that stateid if
the delegreturn has freed it on the server.
To do so, we ensure that we do not free the storage for the delegation
until either it is replaced by a new one, or we throw the inode out of
cache.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
In nfs_inode_find_state_and_recover() we want to mark for recovery
only those stateids that match or are older than the supplied
stateid parameter.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Fix the checks in nfs4_inode_make_writeable() to ignore the case where
we hold no delegations. Currently, in such a case, we automatically
flush writes.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Ensure that we check that the delegation is valid in
nfs4_return_incompatible_delegation() before we try to return it.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
If the delegation was revoked, or is already being returned, just
clear the NFS_DELEGATION_RETURN and NFS_DELEGATION_RETURN_IF_CLOSED
flags and keep going.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
If we revoke a delegation, but the stateid's seqid is newer, then
ensure we update the seqid when marking the delegation as revoked.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
If the server sent us a new delegation stateid that is more recent than
the one that got revoked, then clear the NFS_DELEGATION_REVOKED flag.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Add a check to ensure that we haven't already removed the delegation
from the inode after we take all the relevant locks.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Rename nfs_inode_return_delegation_noreclaim() to
nfs_inode_evict_delegation(), which better describes what it
does.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
If we're processsing a delegation recall, ignore the delegations that
have already been revoked or returned.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
If the delegation is marked as being revoked, then don't use it in
the open state structure.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
NFSv2, v3 and NFSv4 servers often have duplicate replay caches that look
at the source port when deciding whether or not an RPC call is a replay
of a previous call. This requires clients to perform strange TCP gymnastics
in order to ensure that when they reconnect to the server, they bind
to the same source port.
NFSv4.1 and NFSv4.2 have sessions that provide proper replay semantics,
that do not look at the source port of the connection. This patch therefore
ensures they can ignore the rebind requirement.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
If a NFSv3 server is being used as both a DS and as a regular NFSv3 server,
we may want to keep the IO traffic on a separate TCP connection, since
it will typically have very different timeout characteristics.
This patch therefore sets up a flag to separate the two modes of operation
for the nfs_client.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Connecting to the DS is a non-interactive, asynchronous task, so there is
no reason to fire up an extra RPC null ping in order to ensure that the
server is up.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Add a flag to tell the nfs_client it should set RPC_CLNT_CREATE_NOPING when
creating the rpc client.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Simplify the struct iattr timestamp encoding by skipping the step of
an intermediate struct timespec.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Simplify the struct iattr timestamp encoding by skipping the step of
an intermediate struct timespec.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Encode the mtime correctly.
Fixes: 95582b0083 ("vfs: change inode times to use struct timespec64")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Convert the NFSv4 callbacks to use struct timestamp64, rather than
truncating times to 32-bit values.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
NFSv4 supports 64-bit timestamps, so there is no point in converting
the struct iattr timestamps to 32-bits before encoding.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
NFSv4 supports 64-bit times, so we should switch to using struct
timespec64 when decoding attributes.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
If we set nfs_mountpoint_expiry_timeout to a negative value, then
allow that to imply that we do not expire NFSv4 submounts.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
This adds a devicetree for the Kobo Clara HD Ebook reader. It
is on based on boards called "e60k02". It is equipped with an
imx6sll SoC.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Netronix board E60K02 can be found some several Ebook-Readers,
at least the Kobo Clara HD and the Tolino Shine 3. The board
is equipped with different SoCs requiring different pinmuxes.
For now the following peripherals are included:
- LED
- Power Key
- Cover (gpio via hall sensor)
- RC5T619 PMIC (the kernel misses support for rtc and charger
subdevices).
- Backlight via lm3630a
- Wifi sdio chip detection (mmc-powerseq and stuff)
It is based on vendor kernel but heavily reworked due to many
changed bindings.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a compatible string for the Kobo Clara HD eBook reader.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The IDT ClockMatrix (TM) family includes integrated devices that provide
eight PLL channels. Each PLL channel can be independently configured as a
frequency synthesizer, jitter attenuator, digitally controlled
oscillator (DCO), or a digital phase lock loop (DPLL). Typically
these devices are used as timing references and clock sources for PTP
applications. This patch adds support for the device.
Co-developed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree binding doc for the IDT ClockMatrix PTP clock.
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add new Marvell CN9130 SoC support (CN9130 is made of one AP807 and
one internal CP115, similar to the Armada 7K/8K using AP806 and
CP110).
- Reorganize EspressoBin device tree to add new variant of the boards
(Armada 3270 based)
- Add firmware node for turris Mox (Armada 3720 based)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXb9CgAAKCRALBhiOFHI7
1USvAJ4u8Tl7qm8B4tuo/fazwbjfrMKMZQCdFFRU6NRElJcjQw99FYQTwJMV+aM=
=J+uU
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-5.5-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt64 for 5.5 (part 1)
- Add new Marvell CN9130 SoC support (CN9130 is made of one AP807 and
one internal CP115, similar to the Armada 7K/8K using AP806 and
CP110).
- Reorganize EspressoBin device tree to add new variant of the boards
(Armada 3270 based)
- Add firmware node for turris Mox (Armada 3720 based)
* tag 'mvebu-dt64-5.5-1' of git://git.infradead.org/linux-mvebu: (23 commits)
arm64: dts: armada-3720-turris-mox: add firmware node
arm64: dts: marvell: add ESPRESSObin variants
arm64: dts: marvell: Add support for Marvell CN9132-DB
arm64: dts: marvell: Add support for Marvell CN9131-DB
arm64: dts: marvell: Add support for Marvell CN9130-DB
arm64: dts: marvell: Add support for Marvell CN9130 SoC support
arm64: dts: marvell: Add support for CP115
arm64: dts: marvell: Externalize PCIe macros from CP11x file
arm64: dts: marvell: Drop PCIe I/O ranges from CP11x file
arm64: dts: marvell: Prepare the introduction of CP115
arm64: dts: marvell: Fix CP110 NAND controller node multi-line comment alignment
arm64: dts: marvell: Add AP807-quad cache description
arm64: dts: marvell: Add AP806-quad cache description
arm64: dts: marvell: Add AP806-dual cache description
arm64: dts: marvell: Add support for AP807/AP807-quad
dt-bindings: marvell: Declare the CN913x SoC compatibles
dt-bindings: marvell: Convert the SoC compatibles description to YAML
arm64: dts: marvell: Move clocks to AP806 specific file
arm64: dts: marvell: Prepare the introduction of AP807 based SoCs
MAINTAINERS: Add new Marvell CN9130-based files to track
...
Link: https://lore.kernel.org/r/87zhhc3bo6.fsf@FE-laptop
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable L2 cache parity and ECC on a Armada XP SoC family and allow
to use in on the Armada 38x SoCs too.
- Use correct name for the rs5c372a on synology (Kirkwood based)
- Rename "sa-sram" node to "sram" on dove
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXb9ANAAKCRALBhiOFHI7
1YxGAJ42trDdNhPczQeHvNx2UcvmSKU8rQCfdNMvDGGosrbJ/aWklGPQfU4iano=
=0o2E
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-5.5-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt for 5.5 (part 1)
- Enable L2 cache parity and ECC on a Armada XP SoC family and allow
to use in on the Armada 38x SoCs too.
- Use correct name for the rs5c372a on synology (Kirkwood based)
- Rename "sa-sram" node to "sram" on dove
* tag 'mvebu-dt-5.5-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-xp: add label to sdram-controller node
ARM: dts: mvebu: add sdram controller node to Armada-38x
ARM: dts: armada-xp: enable L2 cache parity and ecc on db-xc3-24g4xg
ARM: dts: dove: Rename "sa-sram" node to "sram"
ARM: dts: kirkwood: synology: Fix rs5c372 RTC entry
Link: https://lore.kernel.org/r/8736f44q9l.fsf@FE-laptop
Signed-off-by: Olof Johansson <olof@lixom.net>
Adds support for DP and XUSB on various boards, enables SMMU support for
more devices and fixes a couple of DTC warnings and inconsistencies that
are reported at runtime.
These changes along with some of the driver changes in other branches
allow suspend/resume support on Tegra210 devices (e.g. Jetson TX1 and
Jetson Nano).
-----BEGIN PGP SIGNATURE-----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=NTCt
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.5-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.5-rc1
Adds support for DP and XUSB on various boards, enables SMMU support for
more devices and fixes a couple of DTC warnings and inconsistencies that
are reported at runtime.
These changes along with some of the driver changes in other branches
allow suspend/resume support on Tegra210 devices (e.g. Jetson TX1 and
Jetson Nano).
* tag 'tegra-for-5.5-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (25 commits)
arm64: tegra: Add Jetson Nano SC7 timings
arm64: tegra: Add Jetson TX1 SC7 timings
arm64: tegra: Enable wake from deep sleep on RTC alarm
arm64: tegra: Add PMU on Tegra210
arm64: tegra: Add blank lines for better readability
arm64: tegra: Enable DisplayPort on Jetson AGX Xavier
arm64: tegra: p2888: Rename regulators for consistency
arm64: tegra: Enable DP support on Jetson TX2
arm64: tegra: Fix compatible for SOR1
arm64: tegra: Enable DP support on Jetson Nano
arm64: tegra: Add SOR0_OUT clock on Tegra210
arm64: tegra: Assume no CLKREQ presence by default
arm64: tegra: Enable SMMU for VIC on Tegra186
arm64: tegra: Enable XUSB host controller on Jetson TX2
arm64: tegra: Enable SMMU for XUSB host on Tegra186
arm64: tegra: Enable XUSB pad controller on Jetson TX2
arm64: tegra: Add ethernet alias on Jetson AGX Xavier
arm64: tegra: Fix compatible string for EQOS on Tegra194
arm64: tegra: Hook up edp interrupt on Tegra210 SOCTHERM
arm64: tegra: Fix base address for SOR1 on Tegra194
...
Link: https://lore.kernel.org/r/20191102144521.3863321-8-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Enables the Tegra VDE driver by default. This is currently in staging
but can be used with existing userspace to do hardware-accelerated video
decoding of H.264 streams.
-----BEGIN PGP SIGNATURE-----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=ziJD
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.5-arm-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/defconfig
ARM: tegra: Default configuration changes for v5.5-rc1
Enables the Tegra VDE driver by default. This is currently in staging
but can be used with existing userspace to do hardware-accelerated video
decoding of H.264 streams.
* tag 'tegra-for-5.5-arm-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Enable Tegra VDE driver in tegra_defconfig
Link: https://lore.kernel.org/r/20191102144521.3863321-7-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the device tree to support Toradex Colibri iMX8X a
computer on module which can be used on different carrier boards.
The module consists of an NXP i.MX 8X family SoC (either i.MX 8DualX or
8QuadXPlus), a PF8100 PMIC, a FastEthernet PHY, 1 or 2 GB of LPDDR4
RAM, some level shifters, a Micron eMMC, a USB hub, an AD7879 resistive
touch controller, an SGTL5000 audio codec and on-module CSI as well as
DSI-LVDS FFC receptacles plus an optional Bluetooth/Wi-Fi module.
Anything that is not self-contained on the module is disabled by
default.
The device tree for the Colibri Evaluation Board includes the module's
device tree and enables the supported peripherals of the carrier board
(the Colibri Evaluation Board supports almost all of them).
So far there is no display or USB functionality supported at all but
basic console UART, eMMC and Ethernet functionality work fine.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adds support for CPU frequency scaling on Tegra20 and Tegra30, EMC
frequency scaling on Tegra30, SMMU support for VDE on Tegra30, the
STMPE ADC found on Toradex T30 modules as well as fixes for eDP
support on Venice2.
-----BEGIN PGP SIGNATURE-----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=rlo7
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.5-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.5-rc1
Adds support for CPU frequency scaling on Tegra20 and Tegra30, EMC
frequency scaling on Tegra30, SMMU support for VDE on Tegra30, the
STMPE ADC found on Toradex T30 modules as well as fixes for eDP
support on Venice2.
* tag 'tegra-for-5.5-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: cardhu-a04: Add CPU Operating Performance Points
ARM: tegra: cardhu-a04: Set up voltage regulators for DVFS
ARM: tegra: trimslice: Add CPU Operating Performance Points
ARM: tegra: paz00: Add CPU Operating Performance Points
ARM: tegra: paz00: Set up voltage regulators for DVFS
ARM: tegra: Add CPU Operating Performance Points for Tegra30
ARM: tegra: Add CPU Operating Performance Points for Tegra20
ARM: tegra: Add Tegra30 CPU clock
ARM: tegra: Add Tegra20 CPU clock
ARM: tegra: Add External Memory Controller node on Tegra30
ARM: tegra: nyan-big: Add timings for RAM codes 4 and 6
ARM: tegra: Connect SMMU with Video Decoder Engine on Tegra30
ARM: tegra: Add eDP power supplies on Venice2
ARM: tegra: Add SOR0_OUT clock on Tegra124
ARM: tegra: Add stmpe-adc DT node to Toradex T30 modules
Link: https://lore.kernel.org/r/20191102144521.3863321-6-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
