Use the flagged last output buffer to also flag the corresponding
capture buffer after encoding. This causes the end of stream event
to be issued and the buffer to be dequeued with the last flag set.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there are no pending queued output buffers to be encoded, waking up
the capture queue with -EPIPE signals end of stream. If there are
pending buffers on the other hand, setting the V4L2_BUF_FLAG_LAST on
the resulting encoded capture buffers is all that is needed.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Using the output queue sequence counter to determine the last buffer to
be encoded or decoded always was fragile at best. Now that we have the
last buffer flag propagating from the output queue to the capture queue
correctly, this is not needed anymore.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mark the last output buffer to be encoded.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there are still queued output buffers pending to be copied into the
bitstream ring buffer, setting the stream end flag should be deferred
until the marked last output buffer is written into the bitstream ring
buffer.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mark the last output buffer to be decoded and only copy pending queued
output buffers into the bitstream ring buffer in the BIT processor
decoder case.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since V4L2_BUF_FLAG_LAST is a CAPTURE only flag, clear it from OUTPUT
buffers in QBUF and DQBUF. This allows to use the flag internally to
signal the last buffer to decode after a decoder stop command was
issued.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If no more frames are decoded in bitstream end mode, and a previously
decoded frame has been returned, the firmware still increments the frame
number. To avoid a sequence number mismatch after decoder restart,
increment the sequence_offset correction parameter.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The bitstream ringbuffer might be in an underrun state after draining,
or it might still contain unread data if the previous decoder stop
command was flagged as immediate. Flush the bitstream ring buffer
during V4L2_DEC_CMD_START to get into a well defined state. Also fill
the bitstream with buffers that have been queued during draining,
to resume decoding immediately.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On CODA960, sequence initialization can succeed if less than 512 bytes
are ready in the bitstream ring buffer.
On other variants, warn about too small payload in start_streaming.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the first buffer contains only headers, the sequence initialization
command fails. On CodaHx4 the buffer must be padded to at least 512
bytes, on CODA960 it seems to be enough to just repeat the sequence and
extension headers (MPEG-2) or the VOS and VO headers (MPEG-4) once for
for sequence initialization to succeed without further bitstream data.
On CodaHx4 the headers can be repeated multiple times until the 512 byte
mark is reached.
A similar issue was solved for h.264 by padding with a filler NAL in
commit 0eef89403e ("[media] coda: pad first h.264 buffer to 512
bytes").
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Pass vaddr and size to coda_bitstream_queue instead of a struct
vb2_v4l2_buffer to make it reusable for queueing data that is
not exactly a whole v4l2 buffer into the bitstream ringbuffer.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Combine the separate auxiliary buffer, buffer meta, frame type, and
decode error arrays into an array of struct coda_internal_frame.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The stateful decoder API requires decoders to signal detection
of stream dimensions via the V4L2_EVENT_SOURCE_CHANGE event.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a sequence initialization work item to be run when OUTPUT buffers
are queued in the initialization state.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sequence initialization already has to happen during the
initialization phase, after headers have been queued on the OUTPUT
queue. This means that sequence initialization has to be queued as
a work item from QBUF on the OUTPUT queue. The internal framebuffer
setup should be done later during VIDIOC_REQBUFS() on the CAPTURE
queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the DEC_CMD_STOP command is issued after the context has already
consumed all the queued buffers, we need to make sure to wake the
destination queue with last_buffer_dequeued set, to allow userspace to
make progress in its EOS handling.
As there might still be picture run workers pending at that point, we
need to synchronize with them, so the sequence number comparison reads
stable values.
reword commit message]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Combine setting the last_buffer_dequeued flag on the capture video
queue and waking up its done workqueue into a helper function.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
coda_encoder_cmd() is racy, as the last scheduled picture run worker can
still be in-flight while the ENC_CMD_STOP command is issued. Depending
on the exact timing the sequence numbers might already be changed, but
the last buffer might not have been put on the destination queue yet.
In this case the current implementation would prematurely wake the
destination queue with last_buffer_dequeued=true, causing userspace to
call streamoff before the last buffer is handled.
Close this race window by synchronizing with the pic_run_worker before
doing the sequence check.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[l.stach@pengutronix.de: switch to flush_work, reword commit message]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sequence number handling assumed that the BIT processor frame number
starts counting at 1, but this is not true for the MPEG-2 decoder,
which starts at 0. Fix the sequence counter offset detection to handle
this.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use mem2mem try_en/decoder_cmd helpers to ensure consistent behaviour
with other video codec drivers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CMD_START shall be used to start the processing after a drain that
was initiated with CMD_STOP.
Up until now, a drain on coda could only be finished with a
STREAMOFF-STREAMON, which resulted in a reset of the device.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add nodes for GPU (Mali 400) to Exynos4210 and Exynos4412. Describe the
GPU as much as possible however still few elements are missing:
1. Exynos4210 bus clock is not described in hardware manual therefore
the IP gate clock was provided,
2. Exynos4412: Not sure what to do with CLK_G3D clock responsible for
gating entire IP block (it is now being disabled as unused),
3. Regulator supplies on Trats board.
Limited testing on Odroid U3 (Exynos4412).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add nodes for GPU (Mali 400) to Exynos3250. This is still limited and
not tested:
1. No dynamic voltage and frequency scaling,
2. Not sure what to do with CLK_G3D clock responsible for gating entire
IP block (it is now being disabled as unused).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add vendor compatibles for specific implementation of Mali Utgard
(Exynos3250, Exynos4-family) and Midgard (Exynos5433, Exynos7).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add nodes for GPU (Mali T760) to Exynos7. Current support for Exynos7
misses a lot, including proper clocks, power domains, frequency and
voltage scaling and cooling. However this still can provide basic GPU
description. Not tested on HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add nodes for GPU (Mali T760) to Exynos5433. Missing element is the
cooling device. Not tested on HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Currently perf_rotate_context assumes that if the context's nr_events !=
nr_active a rotation is necessary for perf event multiplexing. With
cgroups, nr_events is the total count of events for all cgroups and
nr_active will not include events in a cgroup other than the current
task's. This makes rotation appear necessary for cgroups when it is not.
Add a perf_event_context flag that is set when rotation is necessary.
Clear the flag during sched_out and set it when a flexible sched_in
fails due to resources.
Signed-off-by: Ian Rogers <irogers@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20190601082722.44543-1-irogers@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Getting the apply_quirk bool from new rapl_model_match array.
And because apply_quirk was the last remaining piece of data
in rapl_cpu_match, replacing it with rapl_model_match as device
table.
The switch to new perf_msr_probe detection API is done.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan <kan.liang@linux.intel.com>
Cc: Liang
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20190616140358.27799-9-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We no longer need model specific attribute arrays,
because we get all this detected in rapl_events_attrs.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan <kan.liang@linux.intel.com>
Cc: Liang
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20190616140358.27799-8-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There's no need to have special code for getting
the bit and MSR value for given event. We can
now easily get it from rapl_msrs array.
Also getting rid of RAPL_IDX_*, which is no longer
needed and replacing INTEL_RAPL* with PERF_RAPL*
enums.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan <kan.liang@linux.intel.com>
Cc: Liang
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20190616140358.27799-7-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We get rapl_cntr_mask from perf_msr_probe call, as a replacement
for current intel_rapl_init_fun::cntr_mask value for each model.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan <kan.liang@linux.intel.com>
Cc: Liang
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20190616140358.27799-6-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Using perf_msr_probe function to probe for RAPL MSRs.
Adding new rapl_model_match device table, that
gathers events info for given model, following
the MSR and cstate module design.
It will replace the current rapl_cpu_match device
table and detection code in following patches.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan <kan.liang@linux.intel.com>
Cc: Liang
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20190616140358.27799-5-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Using perf_msr_probe function to probe for cstate events.
The functionality is the same, with one exception, that
perf_msr_probe checks for rdmsr to return value != 0 for
given MSR register.
Using the new attribute groups and adding the events via
pmu::attr_update.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan <kan.liang@linux.intel.com>
Cc: Liang
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20190616140358.27799-4-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Using perf_msr_probe function to probe for msr events.
The functionality is the same, with one exception, that
perf_msr_probe checks for rdmsr to return value != 0 for
given MSR register.
Using the new attribute groups and adding the events via
pmu::attr_update.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan <kan.liang@linux.intel.com>
Cc: Liang
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20190616140358.27799-3-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Adding perf_msr_probe function to provide interface for
checking up on MSR register and set the related attribute
group visibility.
User defines following struct for each MSR register:
struct perf_msr {
u64 msr;
struct attribute_group *grp;
bool (*test)(int idx, void *data);
bool no_check;
};
Where:
msr - is the MSR address
attrs - is attribute groups array to add if the check passed
test - is test function pointer
no_check - is bool that bypass the check and adds the
attribute without any test
The array of struct perf_msr is passed into:
perf_msr_probe(struct perf_msr *msr, int cnt, bool zero, void *data)
Together with:
cnt - which is the number of struct msr array elements
data - which is user pointer passed to the test function
zero - allow counters that returns zero on rdmsr
The perf_msr_probe will executed test code, read the MSR and
check the value is != 0. If all these tests pass, related
attribute group is kept visible.
Also adding PMU_EVENT_GROUP macro helper to define attribute
group for single attribute. It will be used in following patches.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan <kan.liang@linux.intel.com>
Cc: Liang
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20190616140358.27799-2-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Energy Aware Scheduler (EAS) estimates the energy impact of waking
up a task on a given CPU. This estimation is based on:
a) an (active) power consumption defined for each CPU frequency
b) an estimation of which frequency will be used on each CPU
c) an estimation of the busy time (utilization) of each CPU
Utilization clamping can affect both b) and c).
A CPU is expected to run:
- on an higher than required frequency, but for a shorter time, in case
its estimated utilization will be smaller than the minimum utilization
enforced by uclamp
- on a smaller than required frequency, but for a longer time, in case
its estimated utilization is bigger than the maximum utilization
enforced by uclamp
While compute_energy() already accounts clamping effects on busy time,
the clamping effects on frequency selection are currently ignored.
Fix it by considering how CPU clamp values will be affected by a
task waking up and being RUNNABLE on that CPU.
Do that by refactoring schedutil_freq_util() to take an additional
task_struct* which allows EAS to evaluate the impact on clamp values of
a task being eventually queued in a CPU. Clamp values are applied to the
RT+CFS utilization only when a FREQUENCY_UTIL is required by
compute_energy().
Do note that switching from ENERGY_UTIL to FREQUENCY_UTIL in the
computation of the cpu_util signal implies that we are more likely to
estimate the highest OPP when a RT task is running in another CPU of
the same performance domain. This can have an impact on energy
estimation but:
- it's not easy to say which approach is better, since it depends on
the use case
- the original approach could still be obtained by setting a smaller
task-specific util_min whenever required
Since we are at that:
- rename schedutil_freq_util() into schedutil_cpu_util(),
since it's not only used for frequency selection.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alessio Balsini <balsini@android.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@google.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lkml.kernel.org/r/20190621084217.8167-12-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
So far uclamp_util() allows to clamp a specified utilization considering
the clamp values requested by RUNNABLE tasks in a CPU. For the Energy
Aware Scheduler (EAS) it is interesting to test how clamp values will
change when a task is becoming RUNNABLE on a given CPU.
For example, EAS is interested in comparing the energy impact of
different scheduling decisions and the clamp values can play a role on
that.
Add uclamp_util_with() which allows to clamp a given utilization by
considering the possible impact on CPU clamp values of a specified task.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alessio Balsini <balsini@android.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@google.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lkml.kernel.org/r/20190621084217.8167-11-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Each time a frequency update is required via schedutil, a frequency is
selected to (possibly) satisfy the utilization reported by each
scheduling class and irqs. However, when utilization clamping is in use,
the frequency selection should consider userspace utilization clamping
hints. This will allow, for example, to:
- boost tasks which are directly affecting the user experience
by running them at least at a minimum "requested" frequency
- cap low priority tasks not directly affecting the user experience
by running them only up to a maximum "allowed" frequency
These constraints are meant to support a per-task based tuning of the
frequency selection thus supporting a fine grained definition of
performance boosting vs energy saving strategies in kernel space.
Add support to clamp the utilization of RUNNABLE FAIR and RT tasks
within the boundaries defined by their aggregated utilization clamp
constraints.
Do that by considering the max(min_util, max_util) to give boosted tasks
the performance they need even when they happen to be co-scheduled with
other capped tasks.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alessio Balsini <balsini@android.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@google.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lkml.kernel.org/r/20190621084217.8167-10-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
By default FAIR tasks start without clamps, i.e. neither boosted nor
capped, and they run at the best frequency matching their utilization
demand. This default behavior does not fit RT tasks which instead are
expected to run at the maximum available frequency, if not otherwise
required by explicitly capping them.
Enforce the correct behavior for RT tasks by setting util_min to max
whenever:
1. the task is switched to the RT class and it does not already have a
user-defined clamp value assigned.
2. an RT task is forked from a parent with RESET_ON_FORK set.
NOTE: utilization clamp values are cross scheduling class attributes and
thus they are never changed/reset once a value has been explicitly
defined from user-space.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alessio Balsini <balsini@android.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@google.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lkml.kernel.org/r/20190621084217.8167-9-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A forked tasks gets the same clamp values of its parent however, when
the RESET_ON_FORK flag is set on parent, e.g. via:
sys_sched_setattr()
sched_setattr()
__sched_setscheduler(attr::SCHED_FLAG_RESET_ON_FORK)
the new forked task is expected to start with all attributes reset to
default values.
Do that for utilization clamp values too by checking the reset request
from the existing uclamp_fork() call which already provides the required
initialization for other uclamp related bits.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alessio Balsini <balsini@android.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@google.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lkml.kernel.org/r/20190621084217.8167-8-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The SCHED_DEADLINE scheduling class provides an advanced and formal
model to define tasks requirements that can translate into proper
decisions for both task placements and frequencies selections. Other
classes have a more simplified model based on the POSIX concept of
priorities.
Such a simple priority based model however does not allow to exploit
most advanced features of the Linux scheduler like, for example, driving
frequencies selection via the schedutil cpufreq governor. However, also
for non SCHED_DEADLINE tasks, it's still interesting to define tasks
properties to support scheduler decisions.
Utilization clamping exposes to user-space a new set of per-task
attributes the scheduler can use as hints about the expected/required
utilization for a task. This allows to implement a "proactive" per-task
frequency control policy, a more advanced policy than the current one
based just on "passive" measured task utilization. For example, it's
possible to boost interactive tasks (e.g. to get better performance) or
cap background tasks (e.g. to be more energy/thermal efficient).
Introduce a new API to set utilization clamping values for a specified
task by extending sched_setattr(), a syscall which already allows to
define task specific properties for different scheduling classes. A new
pair of attributes allows to specify a minimum and maximum utilization
the scheduler can consider for a task.
Do that by validating the required clamp values before and then applying
the required changes using _the_ same pattern already in use for
__setscheduler(). This ensures that the task is re-enqueued with the new
clamp values.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alessio Balsini <balsini@android.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@google.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lkml.kernel.org/r/20190621084217.8167-7-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The sched_setattr() syscall mandates that a policy is always specified.
This requires to always know which policy a task will have when
attributes are configured and this makes it impossible to add more
generic task attributes valid across different scheduling policies.
Reading the policy before setting generic tasks attributes is racy since
we cannot be sure it is not changed concurrently.
Introduce the required support to change generic task attributes without
affecting the current task policy. This is done by adding an attribute flag
(SCHED_FLAG_KEEP_POLICY) to enforce the usage of the current policy.
Add support for the SETPARAM_POLICY policy, which is already used by the
sched_setparam() POSIX syscall, to the sched_setattr() non-POSIX
syscall.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alessio Balsini <balsini@android.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@google.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lkml.kernel.org/r/20190621084217.8167-6-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tasks without a user-defined clamp value are considered not clamped
and by default their utilization can have any value in the
[0..SCHED_CAPACITY_SCALE] range.
Tasks with a user-defined clamp value are allowed to request any value
in that range, and the required clamp is unconditionally enforced.
However, a "System Management Software" could be interested in limiting
the range of clamp values allowed for all tasks.
Add a privileged interface to define a system default configuration via:
/proc/sys/kernel/sched_uclamp_util_{min,max}
which works as an unconditional clamp range restriction for all tasks.
With the default configuration, the full SCHED_CAPACITY_SCALE range of
values is allowed for each clamp index. Otherwise, the task-specific
clamp is capped by the corresponding system default value.
Do that by tracking, for each task, the "effective" clamp value and
bucket the task has been refcounted in at enqueue time. This
allows to lazy aggregate "requested" and "system default" values at
enqueue time and simplifies refcounting updates at dequeue time.
The cached bucket ids are used to avoid (relatively) more expensive
integer divisions every time a task is enqueued.
An active flag is used to report when the "effective" value is valid and
thus the task is actually refcounted in the corresponding rq's bucket.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alessio Balsini <balsini@android.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@google.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lkml.kernel.org/r/20190621084217.8167-5-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When a task sleeps it removes its max utilization clamp from its CPU.
However, the blocked utilization on that CPU can be higher than the max
clamp value enforced while the task was running. This allows undesired
CPU frequency increases while a CPU is idle, for example, when another
CPU on the same frequency domain triggers a frequency update, since
schedutil can now see the full not clamped blocked utilization of the
idle CPU.
Fix this by using:
uclamp_rq_dec_id(p, rq, UCLAMP_MAX)
uclamp_rq_max_value(rq, UCLAMP_MAX, clamp_value)
to detect when a CPU has no more RUNNABLE clamped tasks and to flag this
condition.
Don't track any minimum utilization clamps since an idle CPU never
requires a minimum frequency. The decay of the blocked utilization is
good enough to reduce the CPU frequency.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alessio Balsini <balsini@android.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@google.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lkml.kernel.org/r/20190621084217.8167-4-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Because of bucketization, different task-specific clamp values are
tracked in the same bucket. For example, with 20% bucket size and
assuming to have:
Task1: util_min=25%
Task2: util_min=35%
both tasks will be refcounted in the [20..39]% bucket and always boosted
only up to 20% thus implementing a simple floor aggregation normally
used in histograms.
In systems with only few and well-defined clamp values, it would be
useful to track the exact clamp value required by a task whenever
possible. For example, if a system requires only 23% and 47% boost
values then it's possible to track the exact boost required by each
task using only 3 buckets of ~33% size each.
Introduce a mechanism to max aggregate the requested clamp values of
RUNNABLE tasks in the same bucket. Keep it simple by resetting the
bucket value to its base value only when a bucket becomes inactive.
Allow a limited and controlled overboosting margin for tasks recounted
in the same bucket.
In systems where the boost values are not known in advance, it is still
possible to control the maximum acceptable overboosting margin by tuning
the number of clamp groups. For example, 20 groups ensure a 5% maximum
overboost.
Remove the rq bucket initialization code since a correct bucket value
is now computed when a task is refcounted into a CPU's rq.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alessio Balsini <balsini@android.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@google.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lkml.kernel.org/r/20190621084217.8167-3-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Utilization clamping allows to clamp the CPU's utilization within a
[util_min, util_max] range, depending on the set of RUNNABLE tasks on
that CPU. Each task references two "clamp buckets" defining its minimum
and maximum (util_{min,max}) utilization "clamp values". A CPU's clamp
bucket is active if there is at least one RUNNABLE tasks enqueued on
that CPU and refcounting that bucket.
When a task is {en,de}queued {on,from} a rq, the set of active clamp
buckets on that CPU can change. If the set of active clamp buckets
changes for a CPU a new "aggregated" clamp value is computed for that
CPU. This is because each clamp bucket enforces a different utilization
clamp value.
Clamp values are always MAX aggregated for both util_min and util_max.
This ensures that no task can affect the performance of other
co-scheduled tasks which are more boosted (i.e. with higher util_min
clamp) or less capped (i.e. with higher util_max clamp).
A task has:
task_struct::uclamp[clamp_id]::bucket_id
to track the "bucket index" of the CPU's clamp bucket it refcounts while
enqueued, for each clamp index (clamp_id).
A runqueue has:
rq::uclamp[clamp_id]::bucket[bucket_id].tasks
to track how many RUNNABLE tasks on that CPU refcount each
clamp bucket (bucket_id) of a clamp index (clamp_id).
It also has a:
rq::uclamp[clamp_id]::bucket[bucket_id].value
to track the clamp value of each clamp bucket (bucket_id) of a clamp
index (clamp_id).
The rq::uclamp::bucket[clamp_id][] array is scanned every time it's
needed to find a new MAX aggregated clamp value for a clamp_id. This
operation is required only when it's dequeued the last task of a clamp
bucket tracking the current MAX aggregated clamp value. In this case,
the CPU is either entering IDLE or going to schedule a less boosted or
more clamped task.
The expected number of different clamp values configured at build time
is small enough to fit the full unordered array into a single cache
line, for configurations of up to 7 buckets.
Add to struct rq the basic data structures required to refcount the
number of RUNNABLE tasks for each clamp bucket. Add also the max
aggregation required to update the rq's clamp value at each
enqueue/dequeue event.
Use a simple linear mapping of clamp values into clamp buckets.
Pre-compute and cache bucket_id to avoid integer divisions at
enqueue/dequeue time.
Signed-off-by: Patrick Bellasi <patrick.bellasi@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alessio Balsini <balsini@android.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Steve Muckle <smuckle@google.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Todd Kjos <tkjos@google.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lkml.kernel.org/r/20190621084217.8167-2-patrick.bellasi@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The term 'weighted' is not needed since there is no 'unweighted' load.
Instead use the term 'runnable' to distinguish 'runnable' load
(avg.runnable_load_avg) used in load balance from load (avg.load_avg)
which is the sum of 'runnable' and 'blocked' load.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Morten Rasmussen <morten.rasmussen@arm.com>
Cc: Patrick Bellasi <patrick.bellasi@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Perret <quentin.perret@arm.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Valentin Schneider <valentin.schneider@arm.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lkml.kernel.org/r/57f27a7f-2775-d832-e965-0f4d51bb1954@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
