The driver supported turning off regulators in suspend only for S2MPS14
device. However this makes also sense for S2MPS11 and can reduce the
power consumption during suspend to RAM.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Store the regulator ID instead of calling rdev_get_id() every time.
This makes code slightly easier to read as shorter 'rdev_id' variable is
used instead of full call. This can also speed things up by reducing
number of calls, although effect was not measured.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Low-voltage switches (lvs) don't have set_points since the voltage ranges
of the output are really controlled by the inputs. This is a problem for
the newly added linear range support in the probe(), as that will cause
a null pointer dereference error on older platforms like msm8974 which
happen to need to control some of the implemented lvs.
Fix this by adding the appropriate null check.
Fixes: 86f4ff7a0c ("regulator: qcom_spmi: enable linear range info")
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet the max98357a also supports 32, 44.1 and
88.2 kHz sample rate. This support was also introduced recently by
commit fdf34366d3 ("ASoC: max98357a: add missing supported rates").
Actually the machine driver validates the supported sample rates but
this is not really needed because the component driver can all apply
whatever constraints are needed and do their own validation. So, remove
the checks from the machine driver as are not needed at all. This way,
we also support 32, 44.1 and 88.2 kHz sample rates and we get rid of the
errors like the below.
rk3399-gru-sound sound: rockchip_sound_max98357a_hw_params() doesn't support this sample rate: 44100
rk3399-gru-sound sound: ASoC: machine hw_params failed: -22
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_find_dai() finds component first via specified
snd_soc_dai_link_component, and find DAI from it.
We already have soc_find_component() to find component,
but soc_find_dai() has original implementation to find component.
We shouldn't have duplicate implementation to do same things.
This patch uses soc_find_component() at soc_find_dai()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
soc_find_component() is using "of_node" and "name" to finding component,
but we should use snd_soc_dai_link_component now, because it is created
to such purpose.
This patch uses snd_soc_dai_link_component for soc_find_component().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC already has snd_soc_is_matching_component() to confirming
matching component, but, soc_find_component() has original
implementation to confirm component.
We shouldn't have duplicate implementation to do same things.
This patch uses snd_soc_is_matching_component() at soc_find_component()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
move soc_find_component() next to snd_soc_is_matching_component().
This is prepare for soc_find_component() cleanup
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates the macb driver to use NAPI GRO helpers when
receiving SKBs. This improves performances.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use NAPI_POLL_WEIGHT, the default NAPI poll() weight instead of
redefining our own value (which turns out to be 64 as well).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in ff9fb72bc0 (debugfs: return error values, not NULL) the
debugfs APIs were changed to return error pointers rather than NULL
pointers on error, breaking the error checking in ASoC. Update the
code to use IS_ERR() and log the codes that are returned as part of
the error messages.
Fixes: ff9fb72bc0 (debugfs: return error values, not NULL)
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Back in ff9fb72bc0 (debugfs: return error values, not NULL) the
debugfs APIs were changed to return error pointers rather than NULL
pointers on error, breaking the error checking in ASoC. Update the
code to use IS_ERR() and log the codes that are returned as part of
the error messages.
Fixes: ff9fb72bc0 (debugfs: return error values, not NULL)
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 34ac3c3eb8 ("ASoC: core: lock client_mutex while removing
link components") added mutex_lock() at soc_remove_link_components().
Is is called from snd_soc_unbind_card()
snd_soc_unbind_card()
=> soc_remove_link_components()
soc_cleanup_card_resources()
soc_remove_dai_links()
=> soc_remove_link_components()
And, there are 2 way to call it.
(1)
snd_soc_unregister_component()
** mutex_lock()
snd_soc_component_del_unlocked()
=> snd_soc_unbind_card()
** mutex_unlock()
(2)
snd_soc_unregister_card()
=> snd_soc_unbind_card()
(1) case is already using mutex_lock() when it calles
snd_soc_unbind_card(), thus, we will get lockdep warning.
commit 495f926c68 ("ASoC: core: Fix deadlock in
snd_soc_instantiate_card()") tried to fixup it, but still not
enough. We still have lockdep warning when we try unbind/bind.
We need mutex_lock() under snd_soc_unregister_card()
instead of snd_remove_link_components()/snd_soc_unbind_card().
Fixes: 34ac3c3eb8 ("ASoC: core: lock client_mutex while removing link components")
Fixes: 495f926c68 ("ASoC: core: Fix deadlock in snd_soc_instantiate_card()")
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull NVMe updates from Christoph:
"A large chunk of NVMe updates for 5.3. Highlights:
- improved PCIe suspent support (Keith Busch)
- error injection support for the admin queue (Akinobu Mita)
- Fibre Channel discovery improvements (James Smart)
- tracing improvements including nvmetc tracing support (Minwoo Im)
- misc fixes and cleanups (Anton Eidelman, Minwoo Im, Chaitanya
Kulkarni)"
* 'nvme-5.3' of git://git.infradead.org/nvme: (26 commits)
Documentation: nvme: add an example for nvme fault injection
nvme: enable to inject errors into admin commands
nvme: prepare for fault injection into admin commands
nvmet: introduce target-side trace
nvme-trace: print result and status in hex format
nvme-trace: support for fabrics commands in host-side
nvme-trace: move opcode symbol print to nvme.h
nvme-trace: do not export nvme_trace_disk_name
nvme-pci: clean up nvme_remove_dead_ctrl a bit
nvme-pci: properly report state change failure in nvme_reset_work
nvme-pci: set the errno on ctrl state change error
nvme-pci: adjust irq max_vector using num_possible_cpus()
nvme-pci: remove queue_count_ops for write_queues and poll_queues
nvme-pci: remove unnecessary zero for static var
nvme-pci: use host managed power state for suspend
nvme: introduce nvme_is_fabrics to check fabrics cmd
nvme: export get and set features
nvme: fix possible io failures when removing multipathed ns
nvme-fc: add message when creating new association
lpfc: add sysfs interface to post NVME RSCN
...
Herbert Xu recently reported a problem concerning RCU and compiler
barriers. In the course of discussing the problem, he put forth a
litmus test which illustrated a serious defect in the Linux Kernel
Memory Model's data-race-detection code [1].
The defect was that the LKMM assumed visibility and executes-before
ordering of plain accesses had to be mediated by marked accesses. In
Herbert's litmus test this wasn't so, and the LKMM claimed the litmus
test was allowed and contained a data race although neither is true.
In fact, plain accesses can be ordered by fences even in the absence
of marked accesses. In most cases this doesn't matter, because most
fences only order accesses within a single thread. But the rcu-fence
relation is different; it can order (and induce visibility between)
accesses in different threads -- events which otherwise might be
concurrent. This makes it relevant to data-race detection.
This patch makes two changes to the memory model to incorporate the
new insight:
If a store is separated by a fence from another access,
the store is necessarily visible to the other access (as
reflected in the ww-vis and wr-vis relations). Similarly,
if a load is separated by a fence from another access then
the load necessarily executes before the other access (as
reflected in the rw-xbstar relation).
If a store is separated by a strong fence from a marked access
then it is necessarily visible to any access that executes
after the marked access (as reflected in the ww-vis and wr-vis
relations).
With these changes, the LKMM gives the desired result for Herbert's
litmus test and other related ones [2].
[1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.1906041026570.1731-100000@iolanthe.rowland.org/
[2] https://github.com/paulmckrcu/litmus/blob/master/manual/plain/C-S-rcunoderef-1.litmushttps://github.com/paulmckrcu/litmus/blob/master/manual/plain/C-S-rcunoderef-2.litmushttps://github.com/paulmckrcu/litmus/blob/master/manual/plain/C-S-rcunoderef-3.litmushttps://github.com/paulmckrcu/litmus/blob/master/manual/plain/C-S-rcunoderef-4.litmushttps://github.com/paulmckrcu/litmus/blob/master/manual/plain/strong-vis.litmus
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
Tested-by: Akira Yokosawa <akiyks@gmail.com>
Shijie Luo says:
====================
ipv4: fix bugs when enable route_localnet
When enable route_localnet, route of the 127/8 address is enabled.
But in some situations like arp_announce=2, ARP requests or reply
work abnormally.
This patchset fix some bugs when enable route_localnet.
Change History:
V2:
- Change a single patch to a patchset.
- Add bug fix for arp_ignore = 3.
- Add a couple of test for enabling route_localnet in selftests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a simple scripts to exercise several situations when enable
route_localnet.
Signed-off-by: Shijie Luo <luoshijie1@huawei.com>
Signed-off-by: Zhiqiang liu <liuzhiqiang26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When arp_ignore=3, the NIC won't reply for scope host addresses, but
if enable route_locanet, we need to reply ip address with head 127 and
scope RT_SCOPE_HOST.
Fixes: d0daebc3d6 ("ipv4: Add interface option to enable routing of 127.0.0.0/8")
Signed-off-by: Shijie Luo <luoshijie1@huawei.com>
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suppose we have two interfaces eth0 and eth1 in two hosts, follow
the same steps in the two hosts:
# sysctl -w net.ipv4.conf.eth1.route_localnet=1
# sysctl -w net.ipv4.conf.eth1.arp_announce=2
# ip route del 127.0.0.0/8 dev lo table local
and then set ip to eth1 in host1 like:
# ifconfig eth1 127.25.3.4/24
set ip to eth2 in host2 and ping host1:
# ifconfig eth1 127.25.3.14/24
# ping -I eth1 127.25.3.4
Well, host2 cannot connect to host1.
When set a ip address with head 127, the scope of the address defaults
to RT_SCOPE_HOST. In this situation, host2 will use arp_solicit() to
send a arp request for the mac address of host1 with ip
address 127.25.3.14. When arp_announce=2, inet_select_addr() cannot
select a correct saddr with condition ifa->ifa_scope > scope, because
ifa_scope is RT_SCOPE_HOST and scope is RT_SCOPE_LINK. Then,
inet_select_addr() will go to no_in_dev to lookup all interfaces to find
a primary ip and finally get the primary ip of eth0.
Here I add a localnet_scope defaults to RT_SCOPE_HOST, and when
route_localnet is enabled, this value changes to RT_SCOPE_LINK to make
inet_select_addr() find a correct primary ip as saddr of arp request.
Fixes: d0daebc3d6 ("ipv4: Add interface option to enable routing of 127.0.0.0/8")
Signed-off-by: Shijie Luo <luoshijie1@huawei.com>
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the MAC address setup in the probe. The MAC address
retrieved using of_get_mac_address was checked for not containing an
error, but it may also be NULL which wasn't tested. Fix it by replacing
IS_ERR with IS_ERR_OR_NULL.
Fixes: 541ddc66d6 ("net: macb: support of_get_mac_address new ERR_PTR error")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tipc_nl_compat_bearer_set() is only called by tipc_nl_compat_link_set()
which already does the check for msg->req check, so remove it from
tipc_nl_compat_bearer_set(), and do the same in tipc_nl_compat_media_set().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ask device connected on sink pad for link frequency
in order to configure CLK_LANE_REG1 (ui_x4).
If not available, ask for pixel rate information to compute it.
This is needed to deal with compressed format such as JPEG
where number of bits per pixel is unknown: computation of
link frequency from pixel rate is not possible.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sensor needs the MCLK clock running when it's being probed. On
platforms where the sensor is instantiated from a DT (MMP2) it is going
to happen asynchronously.
Therefore, the current modus operandi, where the bridge driver fiddles
with the sensor power and clock itself is not going to fly. As the comments
wisely note, this doesn't even belong there.
Luckily, the ov7670 driver is already able to control its power and
reset lines, we can just drop the MMP platform glue altogether.
It also requests the clock via the standard clock subsystem. Good -- let's
set up a clock instance so that the sensor can ask us to enable the clock.
Note that this is pretty dumb at the moment: the clock is hardwired to a
particular frequency and parent. It was always the case.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
An instance of a sensor on DT-based MMP2 platform is always going to be
created asynchronously.
Let's move the manual device creation away from the core to the Cafe
driver (used on OLPC XO-1, not present in DT) and set up appropriate
async matches: I2C on Cafe, FWNODE on MMP (OLPC XO-1.75).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The platform data is actually not used anywhere (along with the CSI
support) and should be safe to remove.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the names more suitable for devicetree bindings.
There are no board files utilizing this, thus we seem to be at liberty
at renaming this without consequences.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The access to REG_CLKCTRL or REG_CTRL1 without the clock enabled hangs
the machine. Enable the clock first.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove structure members and headers that are not actually used. Saves
us from some noise in subsequent cleanup commits.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This accesses the clock registers directly and thus is going to stay in the
way of making the driver devicetree friendly.
No boards seems to actually use this. If it's somehow actually needed it
needs to be done differently.
This reverts commit 7c269f454e.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the patch refactoring the fw-node, the mt9m111 was broken for all
platform_data based platforms, which were the first aim of this
driver. Only the devicetree platform are still functional, probably
because the testing was done on these.
The result is that -EINVAL is systematically return for such platforms,
what this patch fixes.
[Sakari Ailus: Rework this to resolve a merge conflict and use dev_fwnode]
Fixes: 98480d65c4 ("media: mt9m111: allow to setup pixclk polarity")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Ido Schimmel says:
====================
mlxsw: Thermal and hwmon extensions
This patchset from Vadim includes various enhancements to thermal and
hwmon code in mlxsw.
Patch #1 adds a thermal zone for each inter-connect device (gearbox).
These devices are present in SN3800 systems and code to expose their
temperature via hwmon was added in commit 2e265a8b6c ("mlxsw: core:
Extend hwmon interface with inter-connect temperature attributes").
Currently, there are multiple thermal zones in mlxsw and only a few
cooling devices. Patch #2 detects the hottest thermal zone and the
cooling devices are switched to follow its trends. RFC was sent last
month [1].
Patch #3 allows to read and report negative temperature of the sensors
mlxsw exposes via hwmon and thermal subsystems.
v2 (Andrew Lunn):
* In patch #3, replace '%u' with '%d' in mlxsw_hwmon_module_temp_show()
[1] https://patchwork.ozlabs.org/patch/1107161/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend macros MLXSW_REG_MTMP_TEMP_TO_MC() to allow support of negative
temperature readout, since chip and others thermal components are
capable of operating within the negative temperature.
With no such support negative temperature will be consider as very high
temperature and it will cause wrong readout and thermal shutdown.
For negative values 2`s complement is used.
Tested in chamber.
Example of chip ambient temperature readout with chamber temperature:
-10 Celsius:
temp1: -6.0C (highest = -5.0C)
-5 Celsius:
temp1: -1.0C (highest = -1.0C)
v2 (Andrew Lunn):
* Replace '%u' with '%d' in mlxsw_hwmon_module_temp_show()
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multiple sensors are mapped to the same cooling device, the
cooling device should be set according the worst sensor from the
sensors associated with this cooling device.
Provide the hottest thermal zone detection and enforce cooling device
to follow the temperature trends of the hottest zone only.
Prevent competition for the cooling device control from others zones,
by "stable trend" indication. A cooling device will not perform any
actions associated with a zone with a "stable trend".
When other thermal zone is detected as a hottest, a cooling device is
to be switched to following temperature trends of new hottest zone.
Thermal zone score is represented by 32 bits unsigned integer and
calculated according to the next formula:
For T < TZ<t><i>, where t from {normal trip = 0, high trip = 1, hot
trip = 2, critical = 3}:
TZ<i> score = (T + (TZ<t><i> - T) / 2) / (TZ<t><i> - T) * 256 ** j;
Highest thermal zone score s is set as MAX(TZ<i>score);
Following this formula, if TZ<i> is in trip point higher than TZ<k>,
the higher score is to be always assigned to TZ<i>.
For two thermal zones located at the same kind of trip point, the higher
score will be assigned to the zone which is closer to the next trip
point. Thus, the highest score will always be assigned objectively to
the hottest thermal zone.
All the thermal zones initially are to be configured with mode
"enabled" with the "step_wise" governor.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dedicated thermal zone for each inter-connect device. The
current temperature is obtained from inter-connect temperature sensor
and the default trip points are set to the same values as default ASIC
trip points. These settings could be changed from the user space.
A cooling device (fan) is bound to all inter-connect devices.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Enable USBOTG1 support for evk board, it is dual-role function
port.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The mt9m111_power_on function did not properly clean up whenever it
encountered an error. Do that now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The patch adds the following interfaces according the SMARC Spec 1.1
[1] and provided schematics:
- SMARC SPI0/1
Note: Since Kontron still uses silicon revisions below 1.3 they have
add a spi-nor to implement Workaround #1 of erratum ERR006282.
- SMARC SDIO
- SMARC LCD
- SMARC HDMI
- SMARC Management pins
Note: Kontron don't route all of these pins to the i.MX6, some are
routed to the SoM CPLD.
- SMARC GPIO
- SMARC CSI Camera
Note: As specified in [1] the data lanes are shared to cover the
csi and the parallel case. The case depends on the baseboard so
muxing the data lanes is not part of this patch.
- SMARC I2S
- SMARC Watchdog
Note: The watchdog output pin is routed to the CPLD and the SMARC
header. The CPLD performs a reset after a 30s timeout so we
need to enable the watchdog per default.
- SMARC module eeprom
Due to the lack of hardware not all of these interfaces are tesetd.
[1] https://sget.org/standards/smarc
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The regulator_get() function returns a regulator when it succeeds. There's
no need to check whether the regulator is NULL later on.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
