Drivers that never change their ndev dynamically do not need to use
the get_netdev callback.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Selvin Xavier <selvin.xavier@broadcom.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Acked-by: Adit Ranadive <aditr@vmware.com>
Add timeout to infinite loops during the CPU powerup procedures. It
is better to report an error instead of busylooping for infinite time
in case of failure.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It
has the following features:
- Allwinner H6 quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB or 2GB LPDDR3 RAM
- AXP805 PMIC
- AP6256 Wifi/BT 5.0
- USB 2.0 host port (A)
- USB 2.0 micro usb, OTG
- USB 3.0 Host + 4 port USB hub (GL3510)
- Gigabit Ethernet (Realtek RTL8211E phy)
- HDMI 2.0 port
- soldered eMMC (optional)
- 3x LED (one is on the bottom)
- microphone
- audio jack
- PCIe
Add basic support for the board.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Restore SW_CRYPTO_CONTROL operation on AP_VLAN interfaces for unicast
keys, the original override was intended to be done for group keys as
those are treated specially by mac80211 and would always have been
rejected.
Now the situation is that AP_VLAN support must be enabled by the driver
if it can support it (meaning it can support software crypto GTK TX).
Thus, also simplify the code - if we get here with AP_VLAN and non-
pairwise key, software crypto must be used (driver doesn't know about
the interface) and can be used (driver must've advertised AP_VLAN if
it also uses SW_CRYPTO_CONTROL).
Fixes: db3bdcb9c3 ("mac80211: allow AP_VLAN operation on crypto controlled devices")
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the CPU comes out of suspend, the firmware may have modified the OS
Double Lock Register. Save it in an unused slot of cpu_suspend_ctx, and
restore it on resume.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Some firmwares may reboot CPUs with OS Double Lock set. Make sure that
it is unlocked, in order to use debug exceptions.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
To prevent build fail on some platform which does
not have it in the include file chain.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: a1d2a63399 ("drm/lima: driver for ARM Mali4xx GPUs")
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190409003617.4470-2-yuq825@gmail.com
This is essentially a revert of the commit a7588c896b ("ALSA: timer:
Check ack_list emptiness instead of bit flag"). The intended change
by the commit turns out to be insufficient, as snd_timer_close*()
always calls snd_timer_stop() that deletes the ack_list beforehand.
In theory, we can change the behavior of snd_timer_stop() to sync the
pending ack_list, but this will become a deadlock for the callback
like sequencer that calls again snd_timer_stop() from itself. So,
reverting the change is a more straightforward solution.
Fixes: a7588c896b ("ALSA: timer: Check ack_list emptiness instead of bit flag")
Reported-by: syzbot+58813d77154713f4de15@syzkaller.appspotmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The logic for early allocation of page tables is duplicated between
pgd_kernel_pgtable_alloc() and pgd_pgtable_alloc(). Drop the duplication
by calling one from the other and renaming pgd_kernel_pgtable_alloc()
accordingly.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Switch from per mm_struct to per pmd page table lock by enabling
ARCH_ENABLE_SPLIT_PMD_PTLOCK. This provides better granularity for
large system.
I'm not sure if there is contention on mm->page_table_lock. Given
the option comes at no cost (apart from initializing more spin
locks), why not enable it now.
We only do so when pmd is not folded, so we don't mistakenly call
pgtable_pmd_page_ctor() on pud or p4d in pgd_pgtable_alloc().
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM64 standard pgtable functions are going to use pgtable_page_[ctor|dtor]
or pgtable_pmd_page_[ctor|dtor] constructs. At present KVM guest stage-2
PUD|PMD|PTE level page tabe pages are allocated with __get_free_page()
via mmu_memory_cache_alloc() but released with standard pud|pmd_free() or
pte_free_kernel(). These will fail once they start calling into pgtable_
[pmd]_page_dtor() for pages which never originally went through respective
constructor functions. Hence convert all stage-2 page table page release
functions to call buddy directly while freeing pages.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Yu Zhao <yuzhao@google.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
init_mm doesn't require page table lock to be initialized at
any level. Add a separate page table allocator for it, and the
new one skips page table ctors.
The ctors allocate memory when ALLOC_SPLIT_PTLOCKS is set. Not
calling them avoids memory leak in case we call pte_free_kernel()
on init_mm.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
For pte page, use pgtable_page_ctor(); for pmd page, use
pgtable_pmd_page_ctor(); and for the rest (pud, p4d and pgd),
don't use any.
For now, we don't select ARCH_ENABLE_SPLIT_PMD_PTLOCK and
pgtable_pmd_page_ctor() is a nop. When we do in patch 3, we
make sure pmd is not folded so we won't mistakenly call
pgtable_pmd_page_ctor() on pud or p4d.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
brk_handler() now looks pretty strange and can be refactored to drop its
funny 'handler_found' local variable altogether.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
kprobes and uprobes reserve some BRK immediates for installing their
probes. Define these along with the other reservations in brk-imm.h
and rename the ESR definitions to be consistent with the others that we
already have.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that the debug hook dispatching code takes the triggering exception
level into account, there's no need for the hooks themselves to poke
around with user_mode(regs).
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Kprobes bypasses our debug hook registration code so that it doesn't
get tangled up with recursive debug exceptions from things like lockdep:
http://lists.infradead.org/pipermail/linux-arm-kernel/2015-February/324385.html
However, since then, (a) the hook list has become RCU protected and (b)
the kprobes hooks were found not to filter out exceptions from userspace
correctly. On top of that, the step handler is invoked directly from
single_step_handler(), which *does* use the debug hook list, so it's
clearly not the end of the world.
For now, have kprobes use the debug hook registration API like everybody
else. We can revisit this in the future if this is found to limit
coverage significantly.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Mixing kernel and user debug hooks together is highly error-prone as it
relies on all of the hooks to figure out whether the exception came from
kernel or user, and then to act accordingly.
Make our debug hook code a little more robust by maintaining separate
hook lists for user and kernel, with separate registration functions
to force callers to be explicit about the exception levels that they
care about.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The comment next to the definition of our 'break_hook' list head is
at best wrong but mainly just meaningless. Rip it out.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Since the 'addr' parameter contains an UNKNOWN value for non-watchpoint
debug exceptions, rename it to 'unused' for those hooks so we don't get
tempted to use it in the future.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
do_debug_exception() goes out of its way to return a value that isn't
ever used, so just make the thing void.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Rearrange comment to make the comment style consistent, the previous
function parameters are described first.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This brings the kernel doc in line with the function signature.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is the third step to make MT2701 HDMI stable.
We should not change the rate of parent for hdmi phy when
doing round_rate for this clock. The parent clock of hdmi
phy must be the same as it. We change it when doing set_rate
only.
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
This is the second step to make MT2701 HDMI stable.
The factor depends on the divider of DPI in MT2701, therefore,
we should fix this factor to the right and new one.
Test: search ok
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
This is the first step to make MT2701 hdmi stable.
The parent rate of hdmi phy had set by DPI driver.
We should not set or change the parent rate of MT2701 hdmi phy,
as a result we should remove the flags of "CLK_SET_RATE_PARENT"
from the clock of MT2701 hdmi phy.
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Recalculate the rate of this clock, by querying hardware to
make implementation of recalc_rate() to match the definition.
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
In preparation for arm64 supporting ftrace built on other compiler
options, let's have Makefiles remove the $(CC_FLAGS_FTRACE) flags,
whatever these may be, rather than assuming '-pg'.
There should be no functional change as a result of this patch.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In preparation for arm64 supporting ftrace built on other compiler
options, let's have Makefiles remove the $(CC_FLAGS_FTRACE) flags,
whatever these maybe, rather than assuming '-pg'.
While at it, fix arm32 as well. There should be no functional change as
a result of this patch.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In preparation for arm64 supporting ftrace built on other compiler
options, let's have the arm64 Makefiles remove the $(CC_FLAGS_FTRACE)
flags, whatever these may be, rather than assuming '-pg'.
There should be no functional change as a result of this patch.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Stats is updated by each policy, using the lock by stat can
reduce the contention.
Signed-off-by: Kyle Lin <linkyle0915@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Amlogic G12A embeds the same Synopsys DW-HDMI Controller,
but with :
- a "backport" of the HDR signaling registers from more recent
DW-HDMI controllers, this will need a tweak since it's not
normally present on this version of the DW-HDMI controller
- A direct mapping of TOP and DW-HDMI registers instead of an
internal bus accessed using read/write registers
- Support for RX-SENSE, but not yet implemented
- Support for HDMI 2.1 Dynamic HDR, but not yet implemented
- Different registers mapping for the HDMI PHY setup
This patchs adds support for these changes while providing exact
same support as the previous GXBB, GXL & GXM SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-12-narmstrong@baylibre.com
While switching to the Common Clock Framework is still Work In Progress,
this patch adds the corresponding G12A HDMI PLL setup to be on-par
with the other SoCs support.
The G12A has only a single tweak about the high frequency setup,
where the HDMI PLL needs a specific setup to handle correctly the
5.94GHz DCO frequency.
Apart that, it handls ecorrectly all the other HDMI frequencies
and can achieve even better DMT clock frequency precision with
the larger fractional dividier width.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-10-narmstrong@baylibre.com
This patch adds support for the new OSD+VD Plane blending module
in the CRTC code by adding the G12A code to manage the blending
module and setting the right OSD1 & VD1 plane registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-8-narmstrong@baylibre.com
Amlogic G12A SoC supports the same set of Video Planes, but now
are handled by the new OSD plane blender module.
This patch uses the same VD1 plane for G12A, using the exact same scaler
and VD1 setup registers, except using the new blender register to
disable the plane.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fix typo in commit log]
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-7-narmstrong@baylibre.com
ACPICA commit 0c1495275a35071b957ab59549761c6cd3f413b7
Version 20190405.
Link: 0c149527
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 7586a625f9c34c3169efd88470192bf63119e31a
Some ACPICA userspace tools call acpi_ut_subsystem_shutdown() during
cleanup and dereference a null pointer when cleaning up the
namespace.
Link: 7586a625
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 802ec363be67580f52251219ef90613008495392
Version 20190329.
Link: 802ec363
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 5e5c349e73982aea5d9f74416c0b2eea1b0767a1
Link: 5e5c349e
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Amlogic G12A SoC supports now up to 3 OSD planes (1 more than the
previous SoCs) and a brand new OSD plane blender module.
This patch uses the same OSD1 plane for G12A, using the exact same scaler
and OSD1 setup registers, except using the new blender register to
disable the plane.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: fixed typo in commit log]
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-6-narmstrong@baylibre.com
ACPICA commit 24870bd9e73d71e2a1ff0a1e94519f8f8409e57d
ACPI_NAME_SIZE changed to ACPI_NAMESEG_SIZE
This clarifies that this is the length of an individual
nameseg, not the length of a generic namestring/namepath.
Improves understanding of the code.
Link: 24870bd9
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On Amlogic G12A SoC, the 2,97GHz PLL frequency is not stable enough
to provide a correct 297MHz pixel clock, so switch the PLL base
frequency with a /2 OD when the 297MHz pixel clock is requested.
This solves the issue on G12A and also works fine on GXBB, GXL & GXM.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325141824.21259-2-narmstrong@baylibre.com
Due to a clerical error,there is one zero less for 12800000.
Fix it for 128000000
Fixes: 0fc721b296 ("drm/mediatek: add hdmi driver for MT2701 and MT7623")
Signed-off-by: Wangyan Wang <wangyan.wang@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
