When a request must be dequeued with net2280_dequeue() e.g. due
to a device clear action and the same request is finished by the
function scan_dma_completions() then the function net2280_dequeue()
does not find the request in the following search loop and
returns the error -EINVAL without restoring the status ep->stopped.
Thus the endpoint keeps blocked and does not receive any data
anymore.
This fix restores the status and does not issue an error message.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The OUT endpoint normally blocks (NAK) subsequent packets when a
short packet was received and returns an incomplete queue entry to
the gadget driver. Thereby the gadget driver can detect a short packet
when reading queue entries with a length that is not equal to a
multiple of packet size.
The start_queue() function enables receiving OUT packets regardless of
the content of the OUT FIFO. This results in a race: With the current
code, it's possible that the "!ep->is_in && (readl(&ep->regs->ep_stat)
& BIT(NAK_OUT_PACKETS))" test in start_dma() will fail, then a short
packet will be received, and then start_queue() will call
stop_out_naking(). That's what we don't want (OUT naking gets turned
off while there is data in the FIFO) because then the next driver
request might receive a mixture of old and new packets.
With the patch, this race can't occur because the FIFO's state is
tested after we know that OUT naking is already turned on, and OUT
naking is stopped only when both of the conditions are met. This
ensures that all received data is delivered to the gadget driver,
which can detect a short packet now before new packets are appended
to the last short packet.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currently we set the default number of Tx and Rx descriptors to 128 by
default. For Rx this amounts to a full page (assuming 4K pages) because
each Rx descriptor is 32 Bytes, but for Tx it only amounts to a half
page because each Tx descriptor is 16 Bytes (assuming 4K pages).
Instead of assuming 4K pages, determine the ring size and the number of
descriptors for Tx and Rx based on a calculation using the PAGE_SIZE,
ICE_MAX_NUM_DESC, and ICE_REQ_DESC_MULTIPLE. This change is being made
to improve the performance of the driver when using the default
settings.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During SR-IOV initialization, we allocate and setup VFs with reset, and
since we were going to inform Firmware about our intention to do VFLR by
disabling LAN TX Queue, then we really have to complete VF reset flow with
VFLR using appropriate registers - Otherwise, reset status bit for VF in
the Guest OS might returns DEADBEEF.
This resolves issue to properly initialize VFs in the Guest OS via PCI
passthrough.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_get_guar_num_vsi currently calculates the number of VSIs per PF.
Rework this into a general function ice_get_num_per_func, that can
calculate per PF allocations for not just VSIs but across multiple
resource types.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All VF VSIs need to be reset and rebuild with the main VSIs before
replaying all VSIs, so that all existing switch filters, scheduler tree
and other configuration could be replayed at once. This fixes issues when
doing PFR and CORER reset.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of hoping that our ITR granularity will be 2 usec program the
GLINT_CTL register to make sure the ITR granularity is always 2 usecs.
Now that we know what the ITR granularity will be get rid of the check
in ice_probe() to verify our previous assumption.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Comet Lake is a Intel Processor containing Gen9
Intel HD Graphics. This patch adds the initial set of
PCI IDs. Comet Lake comes off of Coffee Lake - adding
the IDs to Coffee Lake ID list.
More support and features will be in the patches that follow.
v2: Split IDs according to GT. (Rodrigo)
v3: Update IDs.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190318200133.9666-1-anusha.srivatsa@intel.com
Replace all instances of:
for (i = 0; i < pf->num_alloc_vsi; i++)
with the following macro:
ice_for_each_vsi(pf, i)
This will allow the code to be consistent since there are currently
cases of using both.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the ice_aq_set_phy_cfg AQ command, the 16.4 bit is reserved. This
patch will make sure that this bit will never be set to 1.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ice_pf_rxq_wait we are using an unnecessary local variable and also
we are checking if the timeout time was reached after the loop. Get rid
of the local variable and return 0 right when we get a successful
result. This makes it so we can return -ETIMEDOUT if we ever exit the
loop because we know the timeout time has been hit.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a local variable struct device *dev to avoid unnecessary de-references
throughout ice_probe().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes issues with VF queues being disabled, and VF netdev
network carrier being lost after reset. Basically, we need to check if VF
is enabled, and queue configured in reset_all_vfs flow, and disable/enable
those queues appropriately whenever the function is called after
Global/CORER/PFR reset/rebuild/replay.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set egress (Rx) pruning enable flag for VF VSI in VSI ctxt to
enable prune action.
To avoid seeing broadcast packet in different VLAN, pruning enable
flag in VSI ctxt should be set.
Write new functions (fill VSI ctx) to not repeat send ctxt code.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for 6PE (RFC 4798) which uses IPv4-mapped IPv6
nexthop to connect IPv6 islands over IPv4 only MPLS network core.
Prior to this fix, to find the link-layer destination mac address, 6PE
enabled host/router was sending IPv6 ND requests for IPv4-mapped IPv6
nexthop address over the interface facing the IPv4 only core which
wouldn't success as the core is IPv6 free.
This fix changes that behavior on 6PE host to treat the nexthop as IPv4
address and send ARP requests whenever the next-hop address is an
IPv4-mapped IPv6 address.
Below topology illustrates the issue and how the patch addresses it.
abcd::1.1.1.1 (lo) abcd::2.2.2.2 (lo)
R0 (PE/host)------------------------R1--------------------------------R2 (PE/host)
<--- IPv4 MPLS core ---> <------ IPv4 MPLS core -------->
eth1 eth2 eth3 eth4
172.18.0.10 172.18.0.11 172.19.0.11 172.19.0.12
ffff::172.18.0.10 ffff::172.19.0.12
<------------------IPv6 MPLS tunnel ---------------------->
R0 and R2 act as 6PE routers of IPv6 islands. R1 is IPv4 only with MPLS tunnels
between R0,R1 and R1,R2.
docker exec r0 ip -f inet6 route add abcd::2.2.2.2/128 nexthop encap mpls 100 via ::ffff:172.18.0.11 dev eth1
docker exec r2 ip -f inet6 route add abcd::1.1.1.1/128 nexthop encap mpls 200 via ::ffff:172.19.0.11 dev eth4
docker exec r1 ip -f mpls route add 100 via inet 172.19.0.12 dev eth3
docker exec r1 ip -f mpls route add 200 via inet 172.18.0.10 dev eth2
With the change, when R0 sends an IPv6 packet over MPLS tunnel to abcd::2.2.2.2,
using ::ffff:172.18.0.11 as the nexthop, it does neighbor discovery for
172.18.18.0.11.
Signed-off-by: Vinay K Nallamothu <nvinay@juniper.net>
Tested-by: Avinash Lingala <ar977m@att.com>
Tested-by: Aravind Srinivas Srinivasa Prabhakar <aprabh@juniper.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently MIPS32 supports a JIT for classic BPF only, not extended BPF.
This patch adds JIT support for extended BPF on MIPS32, so code is
actually JIT'ed instead of being only interpreted. Instructions with
64-bit operands are not supported at this point.
We can delete classic BPF because the kernel will translate classic BPF
programs into extended BPF and JIT them, eliminating the need for
classic BPF.
Signed-off-by: Hassan Naveed <hnaveed@wavecomp.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: kafai@fb.com
Cc: songliubraving@fb.com
Cc: yhs@fb.com
Cc: netdev@vger.kernel.org
Cc: bpf@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: open list:MIPS <linux-mips@linux-mips.org>
Cc: open list <linux-kernel@vger.kernel.org>
Currently eBPF support is available on MIPS64R2 only. Use MIPS64R6
variants of instructions like multiply, divide, movn, movz so eBPF
can run on the newer ISA. Also, we only need to check ISA revision
before JIT'ing code, because we know the CPU is running a 64-bit
kernel because eBPF JIT is only included in kernels with CONFIG_64BIT=y
due to Kconfig dependencies.
Signed-off-by: Hassan Naveed <hnaveed@wavecomp.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: kafai@fb.com
Cc: songliubraving@fb.com
Cc: yhs@fb.com
Cc: netdev@vger.kernel.org
Cc: bpf@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: open list:MIPS <linux-mips@linux-mips.org>
Cc: open list <linux-kernel@vger.kernel.org>
Since the enabling and disabling of IRQs within preempt_schedule_irq()
is contained in a need_resched() loop, we don't need the outer arch
code loop.
Note that commit a18815abcd ("Use preempt_schedule_irq.") initially
removed the existing loop, but missed the final branch to restore_all.
Commit cdaed73afb ("Fix preemption bug.") missed that and reintroduced
the loop.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-kernel@vger.kernel.org
Remove unneeded hw_dbg prints from igc_ethtool.c file.
Clean up code.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the underline for the _IGC_BASE_H_.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Copy the ntuple feature into list of user selectable features.
Enable the ntuple feature.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for statistics and show basic counters.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
clang points out a harmless signed integer overflow:
drivers/net/ethernet/3com/3c515.c:1530:66: error: implicit conversion from 'int' to 'short' changes value from 32783 to -32753 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast | RxProm;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~
drivers/net/ethernet/3com/3c515.c:1532:52: error: implicit conversion from 'int' to 'short' changes value from 32775 to -32761 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
drivers/net/ethernet/3com/3c515.c:1534:38: error: implicit conversion from 'int' to 'short' changes value from 32773 to -32763 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
Make the variable unsigned to avoid the overflow.
Fixes: Linux-2.1.128pre1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko says:
====================
enc28j60: messaging clean up and ACPI improvements
Most of the patches in the series dedicated to update messaging to use modern
APIs, such as netdev, with a benefit to distinguish devices, if more than one
installed on the system.
Besides that, patch 1 targeting ACPI enabled systems when MAC address provided
there via properties.
And few clean ups are included, such as:
- switching to module_spi_driver()
- converting to use ether_addr_copy() API
- converting to use SPDX
Since v2:
- cover letter is added
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix few indentation splats. No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amend comments in the code:
- adding periods to the multi-line comments
- fixing typos
- capitalize first word in the sentences
- etc
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug prints of network operations will look better if network
device name is printed. The benefit of that is a possibility to distinguish
the actual hardware when more than one is installed on the system.
Convert appropriate printk(KERN_DEBUG) to netdev_print(KERN_DEBUG, ndev).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug prints of hardware status and operations will look better
if SPI device name is printed. The benefit of that is a possibility
to distinguish the actual hardware when more than one is installed
on the system.
Convert appropriate printk(KERN_DEBUG) to dev_print(KERN_DEBUG, &spi->dev).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using open coded printk(KERN_<LEVEL>) switch the driver to use
dev_<level> macros.
Note, the device name will be printed in full, which is beneficial when
more than one card installed on the system.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ether_addr_copy() instead of memcpy() to copy the mac address.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate some boilerplate code by using module_spi_driver() instead of
->init() / ->exit(), moving the salient bits from ->init() into ->probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dev_<level>() macros are used against SPI device, the driver's name
is printed as well. No need to duplicate this explicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace open coded netdev_<level>() macros.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->probe() and ->remove() stages can be easily debugged with
initcall_debug or function tracer. There is no need to repeat the same
explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the DT-specific of_get_mac_address() function with
device_get_mac_address, which works on both DT and ACPI platforms.
This change makes it easier to add ACPI support.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lockdep warns that prepare_lock and genpd->mlock can cause a deadlock
the deadlock scenario is like following:
First thread is probing cs2000
cs2000_probe()
clk_register()
__clk_core_init()
clk_prepare_lock() ----> acquires prepare_lock
cs2000_recalc_rate()
i2c_smbus_read_byte_data()
rcar_i2c_master_xfer()
dma_request_chan()
rcar_dmac_of_xlate()
rcar_dmac_alloc_chan_resources()
pm_runtime_get_sync()
__pm_runtime_resume()
rpm_resume()
rpm_callback()
genpd_runtime_resume() ----> acquires genpd->mlock
Second thread is attaching any device to the same PM domain
genpd_add_device()
genpd_lock() ----> acquires genpd->mlock
cpg_mssr_attach_dev()
of_clk_get_from_provider()
__of_clk_get_from_provider()
__clk_create_clk()
clk_prepare_lock() ----> acquires prepare_lock
Since currently no PM provider access genpd's critical section
in .attach_dev, and .detach_dev callbacks, so there is no need to protect
these two callbacks with genpd->mlock.
This patch avoids a potential deadlock by moving out .attach_dev and .detach_dev
from genpd->mlock, so that genpd->mlock won't be held when prepare_lock is acquired
in .attach_dev and .detach_dev
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix following sparse warning:
drivers/scsi/mvumi.c:1797:48: warning: Using plain integer as NULL pointer
drivers/scsi/mvumi.c:2143:50: warning: Using plain integer as NULL pointer
drivers/scsi/mvumi.c:755:58: warning: Using plain integer as NULL pointer
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/qedi/qedi_fw.c: In function 'qedi_tmf_resp_work':
drivers/scsi/qedi/qedi_fw.c:158:28: warning:
variable 'cls_sess' set but not used [-Wunused-but-set-variable]
drivers/scsi/qedi/qedi_fw.c: In function 'qedi_tmf_work':
drivers/scsi/qedi/qedi_fw.c:1370:28: warning:
variable 'cls_sess' set but not used [-Wunused-but-set-variable]
It's never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add show and configure network flow classification (NFC) methods
to the ethtool. Show the specifies Rx ntuple filters.
Configures receive network flow classification option or rules.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable the multi queues to receive.
Program the direction of packets to specified queues according
to the mode selected in the MRQC register.
Multiple receive queues defined by filters and RSS for 4 queues.
Enable/disable RSS hashing and also to enable multiple receive queues.
This patch will allow further ethtool support development.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are some new e1000e devices can only be woken up from D3 one time,
by plugging Ethernet cable. Subsequent cable plugging does set PME bit
correctly, but it still doesn't get woken up.
Since e1000e connects to the root complex directly, we rely on ACPI to
wake it up. In this case, the GPE from _PRW only works once and stops
working after that. Though it appears to be a platform bug, e1000e
maintainers confirmed that I219 does not support D3.
So disable runtime PM on CNP+ chips. We may need to disable earlier
generations if this bug also hit older platforms.
Bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=280819
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
