This add all the structs of IPU3 firmware ABI.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Document the interface for metadata output, including
V4L2_BUF_TYPE_META_OUTPUT buffer type and V4L2_CAP_META_OUTPUT capability
bits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Tested-by: Tian Shu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The V4L2_BUF_TYPE_META_OUTPUT mirrors the V4L2_BUF_TYPE_META_CAPTURE with
the exception that it is an OUTPUT type. The use case for this is to pass
buffers to the device that are not image data but metadata. The formats,
just as the metadata capture formats, are typically device specific and
highly structured.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Tested-by: Tian Shu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When debug with kaslr, it is sometimes necessary to have PHYS_OFFSET to
perform linear virtual address to physical address translation.
Sometimes we're debugging with only few information such as a kernel log
and a symbol file, print PHYS_OFFSET in dump_kernel_offset() for that case.
Tested by:
echo c > /proc/sysrq-trigger
[ 11.996161] SMP: stopping secondary CPUs
[ 11.996732] Kernel Offset: 0x2522200000 from 0xffffff8008000000
[ 11.996881] PHYS_OFFSET: 0xffffffeb40000000
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch remove the follow complete task from TODO documentation:
drm_mode_config.crtc_idr is misnamed, since it contains all KMS object.
Should be renamed to drm_mode_config.object_idr.
Signed-off-by: Shayenne da Luz Moura <shayenneluzmoura@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213225537.nq4dwidn6tma33iv@smtp.gmail.com
Enable McSPI0 of main domain and add DT node for the SPI NOR flash
connected to CS0.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There are 3 instances of McSPI in MCU domain and 4 instances in Main domain.
Add DT nodes for all McSPI instances present on AM654 SoC.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Populate power-domain property for UART nodes, this is required for
Linux to enable UART clocks via PM calls. Without this UART instances
not initialized by bootloader (like main_uart1) fails to work in Linux.
Also, drop current-speed property from main_uart1 and main_uart2 nodes
as these UARTs are not initialized before Linux boots up and current
speed is unknown.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add pinmux for main uart0 that is serves as console on AM654 EVM
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add pinctrl regions for the main and wkup mmr.
The range for main pinctrl region contains a gap
at offset 0x2e4, and because of this, the pinctrl
range is split into two sections.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
The dt-bindings header for TI K3 AM6 SoCs define a set of macros for
defining pinmux configs in human readable form, instead of raw-coded
hex values.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
I guess
|| (rm -f $@ && echo false)
... should be
|| (rm -f $@ && false)
In fact, no Makefile needs to delete a target explicitly on error.
It is automatically done since commit 9c2af1c737 ("kbuild: add
.DELETE_ON_ERROR special target").
I also reused equivalent cmd_shipped from scripts/Makefile.lib.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
I fixed a race condition in the parallel building of ARM in commit
3939f33450 ("ARM: 8418/1: add boot image dependencies to not
generate invalid images").
I see the same problem for MicroBlaze too.
"make -j<N> ARCH=microblaze all linux.bin.ub" results in a broken build
because two threads descend into arch/microblaze/boot simultaneously.
Add proper dependencies to avoid it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
linux.bin, linux.bin.gz, and linux.bin.ub are phony targets to
generate a corresponding image under arch/microblaze/boot/.
simpleImage.% also works like a phony target, but a pattern that
contains '%' cannot be a phony target. I replaced it with equivalent
simpleImage.$(DTB).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit fixes some build issues.
The first issue is the breakage of linux.bin.ub target since commit
ece97f3a5f ("microblaze: Fix simpleImage format generation")
because the addition of UIMAGE_{IN,OUT} affected it.
make ARCH=microblaze CROSS_COMPILE=microblaze-linux- linux.bin.ub
[ snip ]
OBJCOPY arch/microblaze/boot/linux.bin
UIMAGE arch/microblaze/boot/linux.bin.ub.ub
/usr/bin/mkimage: Can't open arch/microblaze/boot/linux.bin.ub: No such file or directory
make[1]: *** [arch/microblaze/boot/Makefile;14: arch/microblaze/boot/linux.bin.ub] Error 1
make: *** [arch/microblaze/Makefile;83: linux.bin.ub] Error 2
The second issue is the use of the "if_changed" multiple times for
the same target.
As commit 92a4728608 ("x86/boot: Fix if_changed build flip/flop bug")
pointed out, this never works properly. Moreover, generating multiple
images as a side-effect is confusing.
Let's split the build recipe for each image.
simpleImage.<dt>*.unstrip is just a copy of vmlinux.
simpleImage.<dt> and simpleImage.<dt>.ub are created in the same way
as linux.bin and linux.bin.ub, respectively.
I kept simpleImage.* recipes independent of linux.bin.* ones to not
change the behavior.
Lastly, this commit fixes "make ARCH=microblaze clean". Previously,
it only cleaned up the unstrip image. Now, all the simpleImage files
are cleaned.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
To prepare for more fixes, move this to arch/microblaze/Makefile.
Otherwise, the same "... is ready" would be printed multiple times.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
"make ARCH=microblaze help" mentions simpleImage.<dt>.unstrip,
but it is not a real Make target. It does not work because Makefile
assumes "system.unstrip" is the name of DT.
$ make ARCH=microblaze CROSS_COMPILE=microblaze-linux- simpleImage.system.unstrip
[ snip ]
make[1]: *** No rule to make target 'arch/microblaze/boot/dts/system.unstrip.dtb', needed by 'arch/microblaze/boot/dts/system.dtb'. Stop.
make: *** [Makefile;1060: arch/microblaze/boot/dts] Error 2
make: *** Waiting for unfinished jobs....
simpleImage.<dt> works like a phony target that generates multiple
images. Reflect the real behavior. I removed the DT directory path
information because it is already explained a few lines below.
While I am here, I deleted the redundant *_defconfig explanation.
The top-level Makefile caters to list available defconfig files:
mmu_defconfig - Build for mmu
nommu_defconfig - Build for nommu
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The fimd hardware supports different blend modes. Add pixel blend mode
property and make it configurable, by modifying the blend equation.
Tested on TRATS2 with Exynos 4412 CPU, on top of linux-next-20181019.
Signed-off-by: Christoph Manszewski <c.manszewski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The fimd hardware supports variable plane alpha. Currently planes
are opaque, make this configurable.
Tested on TRATS2 with Exynos 4412 CPU, on top of linux-next-20181019.
Signed-off-by: Christoph Manszewski <c.manszewski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Add SCU clock common part which will be used by client clock drivers.
SCU clocks are totally different from the legacy clocks (No much
legacy things can be reused), it's using a firmware interface now based
on SCU protocol. So a new configuration option CONFIG_MXC_CLK_SCU is added.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
[sboyd@kernel.org: Mark ccm_ipc_handle static]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The patch introduces CONFIG_MXC_CLK option for legacy MMIO clocks,
this is required to compile legacy MMIO clock conditionally when adding
SCU based clocks for MX8 platforms later.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Low-Power Clock Gate (LPCG) modules contain a local programming
model to control the clock gates for the peripherals. An LPCG module
is used to locally gate the clocks for the associated peripheral.
Note:
This level of clock gating is provided after the clocks are generated
by the SCU resources and clock controls. Thus even if the clock is
enabled by these control bits, it might still not be running based
on the base resource.
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The value for OEM_CFG_UPDATE command differs between driver and the
Management firmware (mfw). Fix this gap with adding a reserved field.
Fixes: cac6f69154 ("qed: Add support for Unified Fabric Port.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When booting a kvm-pr guest on a POWER9 machine the following message is
observed:
"qemu-system-ppc64: KVM does not support 1TiB segments which guest expects"
This is because the guest is expecting to be able to use 1T segments
however we don't indicate support for it. This is because we don't set
the BOOK3S_HFLAG_MULTI_PGSIZE flag in the hflags in kvmppc_set_pvr_pr()
on POWER9.
POWER9 does indeed have support for 1T segments, so add a case for
POWER9 to the switch statement to ensure it is set.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Testing has revealed an occasional crash which appears to be caused
by a race between kvmppc_switch_mmu_to_hpt and kvm_unmap_hva_range_hv.
The symptom is a NULL pointer dereference in __find_linux_pte() called
from kvm_unmap_radix() with kvm->arch.pgtable == NULL.
Looking at kvmppc_switch_mmu_to_hpt(), it does indeed clear
kvm->arch.pgtable (via kvmppc_free_radix()) before setting
kvm->arch.radix to NULL, and there is nothing to prevent
kvm_unmap_hva_range_hv() or the other MMU callback functions from
being called concurrently with kvmppc_switch_mmu_to_hpt() or
kvmppc_switch_mmu_to_radix().
This patch therefore adds calls to spin_lock/unlock on the kvm->mmu_lock
around the assignments to kvm->arch.radix, and makes sure that the
partition-scoped radix tree or HPT is only freed after changing
kvm->arch.radix.
This also takes the kvm->mmu_lock in kvmppc_rmap_reset() to make sure
that the clearing of each rmap array (one per memslot) doesn't happen
concurrently with use of the array in the kvm_unmap_hva_range_hv()
or the other MMU callbacks.
Fixes: 18c3640cef ("KVM: PPC: Book3S HV: Add infrastructure for running HPT guests on radix host")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcEiXXAAoJEEg/ir3gV/o+xxQH/jGS6GQrty9puL40sXKE4ryK
GKVSwbKLnu4WatPcLe/CGxJwRoCVUUKfsbprsuy+oYxhUd5M5h6qu215kZgsfdDC
CfxznbEj3o6mN+ZyZjL+F2gEG6e96bpkKvayb2a9YYQaY/9+V6CMKh3U5jHI+Q2V
D4ToCjWbMXkQ0jsevfpV9W2T0DNfXIa5QGvsvH+D+PoLF/ke/YALZd+yJT0Cm9N2
/vp0qvnHnZO5YavEThN2Lh8f9AY/pAwuGgTrPyddfkZC/6QLH+c8948gF14V+03l
Nz78uSpurQ97X511UBcabSQB0xTCHSAw3/SKCVSxFrpMvkhj4mTbjohwc567Gy4=
=YxUz
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-12-13' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-fixes-2018-12-13
Subject: [pull request][net 0/9] Mellanox, mlx5 fixes 2018-12-13
Saeed Mahameed says:
====================
This series introduces some fixes to the mlx5 core and mlx5e netdevice
driver.
=======
Conflict with net-next: When merged with net-next this series will
cause a moderate conflict:
1) in drivers/net/ethernet/mellanox/mlx5/core/en_tc.c (2 hunks)
Take hunks from net only and just replace *attr->mirror_count to *attr->split_count
1.1) there is one more instance of slow_attr->mirror_count to be replaced
with slow_attr->split_count, it doesn't appear in the conflict, it will
cause a compilation error if left out.
2) in mlx5_ifc.h, take hunks only from net.
Example for the merge resolution can be found at:
https://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux.git/commit/?h=merge/mlx5-fixes&id=48830adf29804d85d77ed8a251d625db0eb5b8a8
branch merge/mlx5-fixes of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
(I simply merged this pull request tag into net-next and resolved the conflict)
I don't know if it's ok with you, but to save your time, you can just:
git pull git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux merge/mlx5-fixes
Into net-next, before your next net merge, and you will have a clean
merge of net into net-next (at least for mlx5 files).
======
Please pull and let me know if there's any problem.
For -stable v4.18
338d615be484 ('net/mlx5e: Cancel DIM work on close SQ')
91f40f9904ad ('net/mlx5e: RX, Verify MPWQE stride size is in range')
For -stable v4.19
c5c7e1c41bbe ('net/mlx5e: Remove unused UDP GSO remaining counter')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata says:
====================
Introduce NETDEV_PRE_CHANGEADDR
Spectrum devices have a limitation that all router interfaces need to
have the same address prefix. In Spectrum-1, the requirement is for the
initial 38 bits of all RIFs to be the same, in Spectrum-2 the limit is
36 bits. Currently violations of this requirement are not diagnosed. At
the same time, if the condition is not upheld, the mismatched MAC
address ends up overwriting the common prefix, and all RIF MAC addresses
silently change to the new prefix.
It is therefore desirable to be able at least to diagnose the issue, and
better to reject attempts to change MAC addresses in ways that is
incompatible with the device.
Currently MAC address changes are notified through emission of
NETDEV_CHANGEADDR, which is done after the change. Extending this
message to allow vetoing is certainly possible, but several other
notification types have instead adopted a simple two-stage approach:
first a "pre" notification is sent to make sure all interested parties
are OK with the change that's about to be done. Then the change is done,
and afterwards a "post" notification is sent.
This dual approach is easier to use: when the change is vetoed, nothing
has changed yet, and it's therefore unnecessary to roll anything back.
Therefore this patchset introduces it for NETDEV_CHANGEADDR as well.
One prominent path to emitting NETDEV_CHANGEADDR is through
dev_set_mac_address(). Therefore in patch #1, give this function an
extack argument, so that a textual reason for rejection (or a warning)
can be communicated back to the user.
In patch #2, add the new notification type. In patch #3, have dev.c emit
the notification for instances of dev_addr change, or addition of an
address to dev_addrs list.
In patches #4 and #5, extend the bridge driver to handle and emit the
new notifier.
In patch #6, change IPVLAN to emit the new notifier.
Likewise for bonding driver in patches #7 and #8. Note that the team
driver doesn't need this treatment, as it goes through
dev_set_mac_address().
In patches #9, #10 and #11 adapt mlxsw to veto MAC addresses on router
interfaces, if they violate the requirement that all RIF MAC addresses
have the same prefix.
Finally in patches #12 and #13, add a test for vetoing of a direct
change of a port device MAC, and indirect change of a bridge MAC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a FID RIF is created for a bridge with IP address, its MAC address
must obey the same requirements as other RIFs. Test that attempts to
change the address incompatibly by attaching a device are vetoed with
extack.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that attempts to change address in a way that violates Spectrum
requirements are vetoed with extack.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On NETDEV_PRE_CHANGEADDR, if the change is related to a RIF interface,
verify that it satisfies the criterion that all RIF interfaces have the
same MAC address prefix, as indicated by mlxsw_sp.mac_mask.
Additionally, besides explicit address changes, check that the address
of an interface for which a RIF is about to be added matches the
required pattern as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Spectrum hardware demands that all router interfaces in the system
have the same first 38 resp. 36 bits of MAC address: the former limit
holds on Spectrum, the latter on Spectrum-2. Add a field that refers to
the required prefix mask and initialize in mlxsw_sp1_init() and
mlxsw_sp2_init().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare mlxsw_sp_netdevice_router_port_event() for handling of
NETDEV_PRE_CHANGEADDR. Split out the part that deals with the actual
changes and call it for the two events currently handled.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Give interested parties an opportunity to veto an impending HW address
change.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before NETDEV_CHANGEADDR, bond driver should emit NETDEV_PRE_CHANGEADDR,
and allow consumers to veto the address change. To propagate further the
return code from NETDEV_PRE_CHANGEADDR, give the function that
implements address change a return value.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A NETDEV_CHANGEADDR event implies a change of address of each of the
IPVLANs of this IPVLAN device. Therefore propagate NETDEV_PRE_CHANGEADDR
to all the IPVLANs.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port device seeks approval of a potential new MAC address, make
sure that should the bridge device end up using this address, all
interested parties would agree with it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is attached to a bridge, the address of the bridge in
question may change as well. Even if it would not change at this
point (because the current bridge address is lower), it might end up
changing later as a result of detach of another port, which can't be
vetoed.
Therefore issue NETDEV_PRE_CHANGEADDR regardless of whether the address
will be used at this point or not, and make sure all involved parties
would agree with the change.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a device address is about to be changed, or an address added to the
list of device HW addresses, it is necessary to ensure that all
interested parties can support the address. Therefore, send the
NETDEV_PRE_CHANGEADDR notification, and if anyone bails on it, do not
change the address.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NETDEV_CHANGEADDR notification is emitted after a device address
changes. Extending this message to allow vetoing is certainly possible,
but several other notification types have instead adopted a simple
two-stage approach: first a "pre" notification is sent to make sure all
interested parties are OK with a change that's about to be done. Then
the change is done, and afterwards a "post" notification is sent.
This dual approach is easier to use: when the change is vetoed, nothing
has changed yet, and it's therefore unnecessary to roll anything back.
Therefore adopt it for NETDEV_CHANGEADDR as well.
To that end, add NETDEV_PRE_CHANGEADDR and an info structure to go along
with it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will add a notifier type NETDEV_PRE_CHANGEADDR, which
allows vetoing of MAC address changes. One prominent path to that
notification is through dev_set_mac_address(). Therefore give this
function an extack argument, so that it can be packed together with the
notification. Thus a textual reason for rejection (or a warning) can be
communicated back to the user.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
proc_sys_lookup can fail with ENOMEM instead of ENOENT when the
corresponding sysctl table is being unregistered. In our case we see
this upon opening /proc/sys/net/*/conf files while network interfaces
are being deleted, which confuses our configuration daemon.
The problem was successfully reproduced and this fix tested on v4.9.122
and v4.20-rc6.
v2: return ERR_PTRs in all cases when proc_sys_make_inode fails instead
of mixing them with NULL. Thanks Al Viro for the feedback.
Fixes: ace0c791e6 ("proc/sysctl: Don't grab i_lock under sysctl_lock.")
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Delalande <colona@arista.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add support to unlock the dimm via the kernel key management APIs. The
passphrase is expected to be pulled from userspace through keyutils.
The key management and sysfs attributes are libnvdimm generic.
Encrypted keys are used to protect the nvdimm passphrase at rest. The
master key can be a trusted-key sealed in a TPM, preferred, or an
encrypted-key, more flexible, but more exposure to a potential attacker.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
