The function rtw_port_switch_chk() returns always false.
Remove the function and related dead code.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use Hal_GetChnlGroup88E() instead of duplicating it's code
in get_rx_power_val_by_reg().
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zeroing the array result[m][n] and setting only the values at
even 'n's simplifies the code and slightly reduces object file
size.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Changes do_insn*_ioctl functions to allow for data lengths for each
comedi_insn of up to 2^16. This patch also changes these functions to only
allocate as much memory as is necessary for each comedi_insn, rather than
allocating a fixed-sized scratch space.
In testing some user-space code for the new INSN_DEVICE_CONFIG_GET_ROUTES
facility with some newer hardware, I discovered that do_insn_ioctl and
do_insnlist_ioctl limited the amount of data that can be passed into the
kernel for insn's to a length of 256. For some newer hardware, the number
of routes can be greater than 1000. Working around the old limits (256)
would complicate the user-space/kernel interaction.
The new upper limit is reasonable with current memory available and does
not otherwise impact the memory footprint for any current or otherwise
typical configuration.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As explained in previous patch, this SPI controller seems to be
tested on SPI flash only before mass production and some bits are
swizzled under other SPI modes probably due to incorrect wiring
inside the silicon. Drop implementation of SPI mode 1/2/3 since
they are broken.
Also drop RT2880_SPI_MODE_BITS macro because we now have only
SPI_LSB_FIRST implemented and the mode_bits is so short that we
don't need a macro there.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to John Crispin (aka blogic) on IRC on Nov 26 2018:
so basically i made cs1 work for MTK/labs when i built
the linkit smart for them. the req-sheet said that cs1 should be proper
duplex spi. however ....
1) the core will always send 1 byte before any transfer, this is the
m25p80 command.
2) mode 3 is broken and bit reversed (?)
3) some bit are incorrectly wired in hw for mode2/3
we wrote a test script and test for [0-0xffff] on all modes and certain
bits are swizzled under certain conditions and it was not possible to
fix this even using a hack.
we then decided to use spi-gpio and i never removed the errornous code
basically the spi is fecked for anything but half duplex spi mode0
running a sflash on it
The controller will always send some data from OPCODE register under half
duplex mode before starting a full-duplex transfer, so the full-duplex
mode is broken.
This piece of code also make CS1 unavailable since it forces the
broken full-duplex mode to be used on CS1.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In this driver, both function the same way, but we want to eventually
kill off semaphores, so a completion is the better choice here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's better to use pre-calculated values to make
on-disk definition more straight-forward and human-readable.
Since there is the only one user, let's remove
__EROFS_BIT entirely.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Gao Xiang <hsiangkao@aol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding an extra MI_STORE_DWORD_IMM to the gpu relocation path for gen3
was good, but still not good enough. To survive 24+ hours under test we
needed to perform not one, not two but three extra store-dw. Doing so
for each GPU relocation was a little unsightly and since we need to
worry about userspace hitting the same issues, we should apply the dummy
store-dw into the EMIT_FLUSH.
Fixes: 7dd4f6729f ("drm/i915: Async GPU relocation processing")
References: 7fa28e1469 ("drm/i915: Write GPU relocs harder with gen3")
Testcase: igt/gem_tiled_fence_blits # blb/pnv
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207134037.11848-1-chris@chris-wilson.co.uk
(cherry picked from commit a889580c08)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Currently we allocate a scratch page for each engine, but since we only
ever write into it for post-sync operations, it is not exposed to
userspace nor do we care for coherency. As we then do not care about its
contents, we can use one page for all, reducing our allocations and
avoid complications by not assuming per-engine isolation.
For later use, it simplifies engine initialisation (by removing the
allocation that required struct_mutex!) and means that we can always rely
on there being a scratch page.
v2: Check that we allocated a large enough scratch for I830 w/a
Fixes: 06e562e7f5 ("drm/i915/ringbuffer: Delay after EMIT_INVALIDATE for gen4/gen5") # v4.18.20
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108850
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204141522.13640-1-chris@chris-wilson.co.uk
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.18.20+
(cherry picked from commit 5179749925)
[Joonas: Use new function in gen9_init_indirectctx_bb too]
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Add some more SiP components to be detected by this soc.c driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
*) Change phy set_mode ops to take both mode and setmode as arguments
*) Add phy_configure() and phy_validate() API's mostly used for MIPI D-PHY
*) Add helpers to get default values of parameters define in MIPI D-PHY spec
*) Add driver for TI's CPSW Port PHY Interface Mode selection
*) Add driver for Cadence Sierra PHY used with USB and PCIe
*) Add driver for Freescale i.MX8MQ USB3 PHY
*) Fixes QMP PHY bindings to allow the clocks provided by the PHY to be
pointed at in device tree
*) Fix for using fully specified regions (in device tree) for configuring
the second lane in dual lane PHYs in QMP PHY
*) Add support for Allwinner H6 USB2 PHY in phy-sun4i-usb driver
*) Update phy-rcar-gen3-usb driver to follow the hardware manual
*) Add support for fine grained power management in mapphone-mdm6600 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
iQJCBAABCgAsFiEEUXMr/TfP2p4suIY5Dlx4XIBNgtkFAlwQj94OHGtpc2hvbkB0
aS5jb20ACgkQDlx4XIBNgtmYrA/9HK7yfOWfNLJ7DB8bi4yPx5hd657sLohSdDEX
0Pxx9PRuxjLYlaHQh8XbHEdvnLIbbGgnHbfvkkHjxJx272G+QAWMi7/SwF3a2ZpY
ev7U1gvWvCTqS/3RsEmxmwiX9esszcOgya2ia5TcyvTIHLla0QXTOUCmOQBejWhJ
Wfe3siSzxn6O4BITsoRUu+0Ek3bScW/cFdby5B62zBrs912p1qlGx20ihvjywB6I
uR5q1w5DxCbC9KZLTkQgfPXki69r1EaCYzdcEKnUON59OXceIy/TKDx/ewZBOjtR
/d+lWybsLMF5MXIy2UKlaKxLrk4AVdsQ6zmfU23uTqCT3rWn7OPEvbzSj3nBXpgi
SNzBTt9wHT4ZAGOq4fmhgF1Gn1gx4tEcarvAfeyyzv1riVgGbwlxSaUpWWvkya/E
zDBqROi/9VU+WX+De+E2KTCAOjJpcnVpLx8euA7uSD2m0nF4Kp4YiyAJiH/ZDQba
ghhR4DiD1xhjO77U+tM7mD+68ZyKsQubqzO+h4rztjZ/QRCWqGtOCg9sSQBxSz86
llEklLB3156dkLnHRMd0NIuSqYGOkHLWdTBrXNr2HaK7ZWvN6jxhC2puziIlmIZl
8m94QyY5pmuTJdQsWA/MEoWFglQqLBDxAVuoMH4d/XFx7PBNxiaTGOOEgX7MhfVM
9di9hak=
=JLIJ
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.21_v1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.21
*) Change phy set_mode ops to take both mode and setmode as arguments
*) Add phy_configure() and phy_validate() API's mostly used for MIPI D-PHY
*) Add helpers to get default values of parameters define in MIPI D-PHY spec
*) Add driver for TI's CPSW Port PHY Interface Mode selection
*) Add driver for Cadence Sierra PHY used with USB and PCIe
*) Add driver for Freescale i.MX8MQ USB3 PHY
*) Fixes QMP PHY bindings to allow the clocks provided by the PHY to be
pointed at in device tree
*) Fix for using fully specified regions (in device tree) for configuring
the second lane in dual lane PHYs in QMP PHY
*) Add support for Allwinner H6 USB2 PHY in phy-sun4i-usb driver
*) Update phy-rcar-gen3-usb driver to follow the hardware manual
*) Add support for fine grained power management in mapphone-mdm6600 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-4.21_v1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (30 commits)
phy: qcom-qmp: Expose provided clocks to DT
dt-bindings: phy-qcom-qmp: Move #clock-cells to child
phy: qcom-qmp: Utilize fully-specified DT registers
dt-bindings: phy-qcom-qmp: Fix register underspecification
phy: ti: fix semicolon.cocci warnings
phy: dphy: Add configuration helpers
phy: Add MIPI D-PHY configuration options
phy: Add configuration interface
phy: Add MIPI D-PHY mode
phy: add driver for Freescale i.MX8MQ USB3 PHY
dt-bindings: phy: add binding for Freescale i.MX8MQ USB3 PHY
phy: Use of_node_name_eq for node name comparisons
net: ethernet: ti: cpsw: add support for port interface mode selection phy
dt-bindings: net: ti: cpsw: switch to use phy-gmii-sel phy
phy: ti: introduce phy-gmii-sel driver
dt-bindings: phy: add cpsw port interface mode selection phy bindings
phy: mvebu-cp110-comphy: fix spelling in structure name
phy: mapphone-mdm6600: Improve phy related runtime PM calls
phy: renesas: rcar-gen3-usb2: follow the hardware manual procedure
phy: cadence: Add driver for Sierra PHY
...
Braswell is really picky about having our writes posted to memory before
we execute or else the GPU may see stale values. A wmb() is insufficient
as it only ensures the writes are visible to other cores, we need a full
mb() to ensure the writes are in memory and visible to the GPU.
The most frequent failure in flushing before execution is that we see
stale PTE values and execute the wrong pages.
References: 987abd5c62 ("drm/i915/execlists: Force write serialisation into context image vs execution")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206084431.9805-3-chris@chris-wilson.co.uk
(cherry picked from commit 490b8c65b9)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Ido Schimmel says:
====================
mlxsw: Add Spectrum-2 multicast routing support
Nir says:
In Spectrum the firmware provided an abstraction for multicast routing
on top of the policy engine. In Spectrum-2 this is no longer the case
and the driver must interact directly with the policy engine in order to
program multicast routes. Every route is written as an ACL rule, its
priority set according to route type (*,G) or (S,G) and its action is an
appropriate multicast routing action. Multicast routes are written to a
specific ACL group which is bound to the appropriate IP protocol
IPv4/IPv6.
Patch #1 adds PEMRBT register needed to declare which ACL group is
dedicated for each IP protocol multicast routing function.
Patch #2 Changes initialization order and puts ACL before router as
multicast router now uses ACL module.
Patch #3 adds Spectrum-2 ACL keys needed for multicast route matching.
Patch #4 adds another ACL profile - in addition to existing flower
profile - which allows the multicast routing module to program rules
directly into the ACL block.
Patch #5 adds the ability to update ACL rules' action, since multicast
routes actions may be updated after being configured.
Patch #6 separates rule creation operation and rule action creation
operation as in multicast router the action is created before the route
is inserted.
Patch #7 sharpens priority handling in Spectrum-2, to ensure incorrect
values are not set to rule's priority.
Patch #8 adds the implementation of multicast routing for IPv4 and IPv6
over existing ACL rule programming
Finally, patch #9 adds a test for IPv4/IPv6 multicast routing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce basic testing for both IPv4 and IPv6 multicast. The test creates
an (S,G) type route, sends traffic and verifies traffic arrives when the
route is present and then verifies traffic does not arrive after deleting
the route.
This test requires smcroute - https://github.com/troglobit/smcroute which
is a tool that allows creation of static multicast routes.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add implementation of Spectrum-2 multicast routes for both IPv4 and IPv6 by
using ACL module explicitly.
In Spectrum-2, multicast routes are set as ACL rules, so initialization
takes care of creating dedicated ACL groups and binding them to the
appropriate multicast routing protocol IPv4/IPv6, and afterwards routes
configuration translates to setting explicit ACL rules.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, higher priority value wins and priority valid values are in
the range of {1,cap_kvd_size-1}. mlxsw_sp_acl_tcam_priority_get converts
from lower-bound priorities alike tc flower to Spectrum-2 HW range. Up
until now tc flower did not provide priority 0 or reached the maximal
value, however multicast routing does provide priority 0.
Therefore, Change mlxsw_sp_acl_tcam_priority_get to verify priority is in
the correct range. Make sure priority is never set to zero and never
exceeds the maximal allowed value.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, when ACL rule was created its action was created with it.
It suits well for tc flower where ACL rule always needs an action, however
it does not suit multicast router, where the action is created prior to
setting a route, which in Spectrum-2 is actually an ACL rule.
Add support for rule creation without action creation. Do it by adding
afa_block argument to mlxsw_sp_acl_rule_create, which if NULL then an
action would be created, also add an indication within struct
mlxsw_sp_acl_rule_info that tells if the action should be destroyed when
the rule is destroyed.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast routes actions may be updated after creation. An example for that
is an addition of an egress interface to an existing route.
So far, as tc flower API dictated, ACL rules were either created or
deleted. Since multicast routes in Spectrum-2 are written to ACL as any
rule, it is required to allow the update of a rule's action as it may
change.
Add methods and operations to support updating rule's action. This is
supported only for Spectrum-2.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add specific ACL operations needed for programming multicast routing ACL
groups and routes.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add virtual router ID fields to Spectrum-2 key blocks set, as the field is
required for multicast routing.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, MC routing is implemented using ACL block explicitly, so
router initialization should take place after ACL initialization.
Set the initialization of the ACL block before IP router initizalization
takes place, so multicast router will be able to allocate ACL data
structures and create its required chains.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, multicast routing is implemented explicitly using policy
engine (ACL) block. PEMRBT register is used to bind a dedicated ACL group
to a specific IP protocol.
Add the register to be later used in multicast router implementation.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed this while working on redoing the reference counting scheme in
the DP MST helpers. Nouveau doesn't attempt to call
drm_dp_mst_topology_mgr_destroy() at all, which leaves it leaking all of
the resources for drm_dp_mst_topology_mgr and it's children mstbs+ports.
Fixes: f479c0ba4a ("drm/nouveau/kms/nv50: initial support for DP 1.2 multi-stream")
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Should hopefully fix a regression some people have been seeing since EVO
push buffers were moved to VRAM by default on Pascal GPUs.
Fixes: d00ddd9da ("drm/nouveau/kms/nv50-: allocate push buffers in vidmem on pascal")
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: <stable@vger.kernel.org> # 4.19+
If CONFIG_DEBUG_SHIRQ is enabled __free_irq() intentionally fires
a spurious interrupt. This interrupt causes a crash because
tp->dev->phydev is NULL at that time.
Fixes: 38caff5a44 ("r8169: handle all interrupt events in the hard irq handler")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to schedule a different tasklet for refill,
This patch remove it.
Suggested-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register a simple clock provider for the PHY pipe clock sources so that
device tree users can point at these clocks via phandles to the lane
nodes.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The phy-qcom-qmp bindings specified #clock-cells as 1. This was never used
because of_clk_add_provider() was never called, so there was no way anybody
could reference these clocks from DT. Furthermore, even if they could be
accessed, the bindings never specified what should go in that additional
cell.
Fix these incomplete and broken bindings. Move the #clock-cells into the
child node, since that is the actual clock provider, and not all
instances of qcom-qmp-phy are clock providers. Also set #clock-cells to
zero, since there's nothing to pass to it.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Utilize the newly fixed up DT bindings to get the tx2 and rx2 register
regions for the second lane of dual-lane PHYs. Before this change,
the driver was simply using lane one's register region and adding
0x400, which reached well beyond the DT-specified register
allocation. This would have been a crash were it not for the page size
on ARM64. Fix the driver not to rely on the magic of virtual memory by
using the newly specified DT register regions for tx2 and rx2.
In order to support existing device trees, this change also contains a
fallback mode for when those new register regions don't exist, which
reverts to the original behavior of overreaching and prints a complaint.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add register regions for the second lane of dual-lane nodes.
This additional specification is needed so that the driver can stop
reaching beyond the tx and rx register allocations to get at the
second lane registers in a dual-lane PHY.
While in there, document #clock-cells as optional for PHYs that don't
provide a pipe clock. Also, document the pcs_misc register region, which
was being quietly supplied and used.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The MIPI D-PHY spec defines default values and boundaries for most of the
parameters it defines. Introduce helpers to help drivers get meaningful
values based on their current parameters, and validate the boundaries of
these parameters if needed.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Now that we have some infrastructure for it, allow the MIPI D-PHY phy's to
be configured through the generic functions through a custom structure
added to the generic union.
The parameters added here are the ones defined in the MIPI D-PHY spec, plus
the number of lanes in use. The current set of parameters should cover all
the potential users.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The phy framework is only allowing to configure the power state of the PHY
using the init and power_on hooks, and their power_off and exit
counterparts.
While it works for most, simple, PHYs supported so far, some more advanced
PHYs need some configuration depending on runtime parameters. These PHYs
have been supported by a number of means already, often by using ad-hoc
drivers in their consumer drivers.
That doesn't work too well however, when a consumer device needs to deal
with multiple PHYs, or when multiple consumers need to deal with the same
PHY (a DSI driver and a CSI driver for example).
So we'll add a new interface, through two funtions, phy_validate and
phy_configure. The first one will allow to check that a current
configuration, for a given mode, is applicable. It will also allow the PHY
driver to tune the settings given as parameters as it sees fit.
phy_configure will actually apply that configuration in the phy itself.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
MIPI D-PHY is a MIPI standard meant mostly for display and cameras in
embedded systems. Add a mode for it.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is a cleaned up port of the downstream i.MX8MQ USB3 PHY driver.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds the binding for the USB3 PHY found on the i.MX8M SoC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
For instances using of_node_cmp, this has the side effect of now using
case sensitive comparisons. This should not matter for any FDT based
system which all of these are.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for port interface mode selection phy (phy-gmii-sel):
- try to request interface mode selection phy from Port DT node and fail
silently if not defined and old CONFIG_TI_CPSW_PHY_SEL driver enabled.
- use new phy if requested successfully.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The cpsw-phy-sel driver was replaced with new PHY driver phy-gmii-sel, so
deprecate cpsw-phy-sel bindings and update CPSW binding to use phy-gmii-sel
PHY bindings.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
TI am335x/am437x/dra7(am5)/dm814x CPSW3G Ethernet Subsystem supports two
10/100/1000 Ethernet ports with selectable G/MII, RMII, and RGMII
interfaces. The interface mode is selected by configuring the MII mode
selection register(s) (GMII_SEL) in the System Control Module chapter
(SCM). GMII_SEL register(s) and bit fields placement in SCM are different
between SoCs while fields meaning is the same.
Historically CPSW external Port's interface mode selection configuration
was introduced using custom API and driver cpsw-phy-sel.c. This leads to
unnecessary driver, DT binding and custom API support effort.
This patch introduces CPSW Port's PHY Interface Mode selection Driver
(phy-gmii-sel) which implements standard Linux PHY interface and used
as a replacement for TI's specific driver cpsw-phy-sel.c and corresponding
custom API.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Rename the mvebu_comhy_conf structure to be mvebu_comphy_conf, which is
probably what the original author meant.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
I noticed that phy_pm_runtime_get_sync() and phy_pm_runtime_put() are not
currently doing anything for phy-mapphone-mdm6600, only the sysfs interface
for works for "auto" and "on".
This is because of the shared GPIO pins between mdm6600 USB port and n_gsm
port. We have not enabled runtime PM for the phy driver until after we've
booted up mdm6600 properly to the USB mode. Otherwise phy_create() would
have called pm_runtime_enable() and pm_runtime_no_callbacks() automatically
on init.
Let's fix this by registering the phy a bit later after we've powered up
the mdm6600 USB port.
And as the PM runtime support is only needed for the n_gsm mode and not for
USB, we can allow the device to idle between phy_mdm6600_power_on() and
phy_mdm6600_power_off(). Note that for suspend, runtime_pm is already
disabled for the phy so we need to check for pm_runtime_enabled().
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
