Add a Sierra PHY driver with PCIe and USB support.
The PHY has multiple lanes, which can be configured into
groups, and a generic PHY device is created for each group.
There are two resets controlling the overall PHY block, one
to enable the APB interface for programming registers, and
another to enable the PHY itself. Additionally there are
resets for each PHY lane.
The PHY can be configured in hardware to read register
settings from ROM, or they can be written by the driver.
The sequence of operation on startup is to enable the APB
bus, write the PHY registers (if required) for each lane
group, and then enable the PHY. Each group of lanes
can then be individually controlled using the power_on()/
power_off() function for that generic PHY
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add DT binding documentation for Sierra PHY. The PHY supports
a number of different protocols, including PCIe and USB.
The PHY lanes may be configured as single or multi-lane links.
Each link is treated as a separate sub-node. For example, if
there are 4 lanes in total the first 2 might be configured as
a multi-lane PCIe link while the other two are single lane
USB links, and in this case there would be 3 sub-nodes.
There are two resets for the PHY block (one for APB register
access, one for the PHY link) and separate resets for each
link. For multi-lane links, the reset corresponds to the
reset line on the master lane, the resets on other lanes
have no effect.
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
After recent changes PHY_MODE_SGMII, PHY_MODE_2500SGMII, PHY_MODE_QSGMII,
PHY_MODE_10GKR are not used any more and can be removed. Hence - remove
them.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Convert mvebu-cp110-comphy PHY driver to use recently introduced
PHY_MODE_ETHERNET and phy_set_mode_ext().
Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add new PHY's mode to be used by Ethernet PHY interface drivers or
multipurpose PHYs like serdes. It will be reused in further changes.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Currently the attempt to add support for Ethernet interface mode PHY
(MII/GMII/RGMII) will lead to the necessity of extending enum phy_mode and
duplicate there values from phy_interface_t enum (or introduce more PHY
callbacks) [1]. Both approaches are ineffective and would lead to fast
bloating of enum phy_mode or struct phy_ops in the process of adding more
PHYs for different subsystems which will make them unmaintainable.
As discussed in [1] the solution could be to introduce dual level PHYs mode
configuration - PHY mode and PHY submode. The PHY mode will define generic
PHY type (subsystem - PCIE/ETHERNET/USB_) while the PHY submode - subsystem
specific interface mode. The last is usually already defined in
corresponding subsystem headers (phy_interface_t for Ethernet, enum
usb_device_speed for USB).
This patch is cumulative change which refactors PHY framework code to
support dual level PHYs mode configuration - PHY mode and PHY submode. It
extends .set_mode() callback to support additional parameter "int submode"
and converts all corresponding PHY drivers to support new .set_mode()
callback declaration.
The new extended PHY API
int phy_set_mode_ext(struct phy *phy, enum phy_mode mode, int submode)
is introduced to support dual level PHYs mode configuration and existing
phy_set_mode() API is converted to macros, so PHY framework consumers do
not need to be changed (~21 matches).
[1] http://lkml.kernel.org/r/d63588f6-9ab0-848a-5ad4-8073143bd95d@ti.com
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
DT bindings normally go in via subsystem maintainers, so add PHY
bindings under generic PHY framework.
Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The USB 2.0 PHY on Allwinner H6 SoC is similar to older Allwinner SoCs,
with some USB0 quirk like A83T and PHY index 1/2 missing.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The new Allwinner H6 SoC's USB2 PHY has two holes -- USB1 (which is a
3.0 port with dedicated PHY) and USB2 (which doesn't exist at all).
Add support for this kind of missing USB PHY index.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The USB2.0 PHY on Allwinner H6 is similar to the ones on the ones on
older SoCs, but with holes in PHY number (USB1 and USB2 are missing, in
which USB1 is a USB3 PHY).
Add binding for the PHY.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Michael and Sandipan report:
Commit ede95a63b5 introduced a bpf_jit_limit tuneable to limit BPF
JIT allocations. At compile time it defaults to PAGE_SIZE * 40000,
and is adjusted again at init time if MODULES_VADDR is defined.
For ppc64 kernels, MODULES_VADDR isn't defined, so we're stuck with
the compile-time default at boot-time, which is 0x9c400000 when
using 64K page size. This overflows the signed 32-bit bpf_jit_limit
value:
root@ubuntu:/tmp# cat /proc/sys/net/core/bpf_jit_limit
-1673527296
and can cause various unexpected failures throughout the network
stack. In one case `strace dhclient eth0` reported:
setsockopt(5, SOL_SOCKET, SO_ATTACH_FILTER, {len=11, filter=0x105dd27f8},
16) = -1 ENOTSUPP (Unknown error 524)
and similar failures can be seen with tools like tcpdump. This doesn't
always reproduce however, and I'm not sure why. The more consistent
failure I've seen is an Ubuntu 18.04 KVM guest booted on a POWER9
host would time out on systemd/netplan configuring a virtio-net NIC
with no noticeable errors in the logs.
Given this and also given that in near future some architectures like
arm64 will have a custom area for BPF JIT image allocations we should
get rid of the BPF_JIT_LIMIT_DEFAULT fallback / default entirely. For
4.21, we have an overridable bpf_jit_alloc_exec(), bpf_jit_free_exec()
so therefore add another overridable bpf_jit_alloc_exec_limit() helper
function which returns the possible size of the memory area for deriving
the default heuristic in bpf_jit_charge_init().
Like bpf_jit_alloc_exec() and bpf_jit_free_exec(), the new
bpf_jit_alloc_exec_limit() assumes that module_alloc() is the default
JIT memory provider, and therefore in case archs implement their custom
module_alloc() we use MODULES_{END,_VADDR} for limits and otherwise for
vmalloc_exec() cases like on ppc64 we use VMALLOC_{END,_START}.
Additionally, for archs supporting large page sizes, we should change
the sysctl to be handled as long to not run into sysctl restrictions
in future.
Fixes: ede95a63b5 ("bpf: add bpf_jit_limit knob to restrict unpriv allocations")
Reported-by: Sandipan Das <sandipan@linux.ibm.com>
Reported-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The > comparison should be >= or we access one element beyond the end
of the array.
(The inst->qinsts[] array is allocated in the ti_msgmgr_probe() function
and it has ->num_valid_queues elements.)
Fixes: a2b79838b8 ("mailbox: ti-msgmgr: Add support for Secure Proxy")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Current mailbox driver of Hi3660 release the mailbox directly
before sending a new message which may cause last message lost
and next message sending doesn't take effect actually.
This patch fixs this issue by following the right progress below,
each time before sending a message, mailbox driver will check
whether the mailbox is in ready state, if last message has been
acknowledged, the mailbox driver will clear the ack state to turn
the mailbox to ready state again.
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Reviewed-and-tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The mbox_chan_ops structure can be const as it is only stored in the
ops field of an mbox_controller structure and this field is const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
A decoy address is used by set_mce_nospec() to update the cache attributes
for a page that may contain poison (multi-bit ECC error) while attempting
to minimize the possibility of triggering a speculative access to that
page.
When reserve_memtype() is handling a decoy address it needs to convert it
to its real physical alias. The conversion, AND'ing with __PHYSICAL_MASK,
is broken for a 32-bit physical mask and reserve_memtype() is passed the
last physical page. Gert reports triggering the:
BUG_ON(start >= end);
...assertion when running a 32-bit non-PAE build on a platform that has
a driver resource at the top of physical memory:
BIOS-e820: [mem 0x00000000fff00000-0x00000000ffffffff] reserved
Given that the decoy address scheme is only targeted at 64-bit builds and
assumes that the top of physical address space is free for use as a decoy
address range, simply bypass address sanitization in the 32-bit case.
Lastly, there was no need to crash the system when this failure occurred,
and no need to crash future systems if the assumptions of decoy addresses
are ever violated. Change the BUG_ON() to a WARN() with an error return.
Fixes: 510ee090ab ("x86/mm/pat: Prepare {reserve, free}_memtype() for...")
Reported-by: Gert Robben <t2@gert.gr>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Gert Robben <t2@gert.gr>
Cc: stable@vger.kernel.org
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: platform-driver-x86@vger.kernel.org
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/154454337985.789277.12133288391664677775.stgit@dwillia2-desk3.amr.corp.intel.com
We're missing a deferred clear off the shallow get, which can cause
a hang. Additionally, when we resize the sbitmap, we should also
flush deferred clears for good measure.
Ensure we have full coverage on batch clears, even for paths where
we would not be doing deferred clear. This makes it less error
prone for future additions.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch enables arm64's bpf_int_jit_compile() to provide
bpf_line_info by calling bpf_prog_fill_jited_linfo().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Commit f149b31557 ("signal: Never allocate siginfo for SIGKILL or SIGSTOP")
means that the seccomp selftest cannot check si_pid under SIGSTOP anymore.
Since it's believed[1] there are no other userspace things depending on the
old behavior, this removes the behavioral check in the selftest, since it's
more a "extra" sanity check (which turns out, maybe, not to have been
useful to test).
[1] https://lkml.kernel.org/r/CAGXu5jJaZAOzP1qFz66tYrtbuywqb+UN2SOA1VLHpCCOiYvYeg@mail.gmail.com
Reported-by: Tycho Andersen <tycho@tycho.ws>
Suggested-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <shuah@kernel.org>
The idea here is just to give a demonstration of how one could safely use
the SECCOMP_RET_USER_NOTIF feature to do mount policies. This particular
policy is (as noted in the comment) not very interesting, but it serves to
illustrate how one might apply a policy dodging the various TOCTOU issues.
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
CC: Kees Cook <keescook@chromium.org>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Oleg Nesterov <oleg@redhat.com>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: "Serge E. Hallyn" <serge@hallyn.com>
CC: Christian Brauner <christian@brauner.io>
CC: Tyler Hicks <tyhicks@canonical.com>
CC: Akihiro Suda <suda.akihiro@lab.ntt.co.jp>
Signed-off-by: Kees Cook <keescook@chromium.org>
This patch introduces a means for syscalls matched in seccomp to notify
some other task that a particular filter has been triggered.
The motivation for this is primarily for use with containers. For example,
if a container does an init_module(), we obviously don't want to load this
untrusted code, which may be compiled for the wrong version of the kernel
anyway. Instead, we could parse the module image, figure out which module
the container is trying to load and load it on the host.
As another example, containers cannot mount() in general since various
filesystems assume a trusted image. However, if an orchestrator knows that
e.g. a particular block device has not been exposed to a container for
writing, it want to allow the container to mount that block device (that
is, handle the mount for it).
This patch adds functionality that is already possible via at least two
other means that I know about, both of which involve ptrace(): first, one
could ptrace attach, and then iterate through syscalls via PTRACE_SYSCALL.
Unfortunately this is slow, so a faster version would be to install a
filter that does SECCOMP_RET_TRACE, which triggers a PTRACE_EVENT_SECCOMP.
Since ptrace allows only one tracer, if the container runtime is that
tracer, users inside the container (or outside) trying to debug it will not
be able to use ptrace, which is annoying. It also means that older
distributions based on Upstart cannot boot inside containers using ptrace,
since upstart itself uses ptrace to monitor services while starting.
The actual implementation of this is fairly small, although getting the
synchronization right was/is slightly complex.
Finally, it's worth noting that the classic seccomp TOCTOU of reading
memory data from the task still applies here, but can be avoided with
careful design of the userspace handler: if the userspace handler reads all
of the task memory that is necessary before applying its security policy,
the tracee's subsequent memory edits will not be read by the tracer.
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
CC: Kees Cook <keescook@chromium.org>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Oleg Nesterov <oleg@redhat.com>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: "Serge E. Hallyn" <serge@hallyn.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
CC: Christian Brauner <christian@brauner.io>
CC: Tyler Hicks <tyhicks@canonical.com>
CC: Akihiro Suda <suda.akihiro@lab.ntt.co.jp>
Signed-off-by: Kees Cook <keescook@chromium.org>
The const qualifier causes problems for any code that wants to write to the
third argument of the seccomp syscall, as we will do in a future patch in
this series.
The third argument to the seccomp syscall is documented as void *, so
rather than just dropping the const, let's switch everything to use void *
as well.
I believe this is safe because of 1. the documentation above, 2. there's no
real type information exported about syscalls anywhere besides the man
pages.
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
CC: Kees Cook <keescook@chromium.org>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Oleg Nesterov <oleg@redhat.com>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: "Serge E. Hallyn" <serge@hallyn.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
CC: Christian Brauner <christian@brauner.io>
CC: Tyler Hicks <tyhicks@canonical.com>
CC: Akihiro Suda <suda.akihiro@lab.ntt.co.jp>
Signed-off-by: Kees Cook <keescook@chromium.org>
In the next patch, we're going to use the sd pointer passed to
__seccomp_filter() as the data to pass to userspace. Except that in some
cases (__seccomp_filter(SECCOMP_RET_TRACE), emulate_vsyscall(), every time
seccomp is inovked on power, etc.) the sd pointer will be NULL in order to
force seccomp to recompute the register data. Previously this recomputation
happened one level lower, in seccomp_run_filters(); this patch just moves
it up a level higher to __seccomp_filter().
Thanks Oleg for spotting this.
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
CC: Kees Cook <keescook@chromium.org>
CC: Andy Lutomirski <luto@amacapital.net>
CC: Oleg Nesterov <oleg@redhat.com>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: "Serge E. Hallyn" <serge@hallyn.com>
Acked-by: Serge Hallyn <serge@hallyn.com>
CC: Christian Brauner <christian@brauner.io>
CC: Tyler Hicks <tyhicks@canonical.com>
CC: Akihiro Suda <suda.akihiro@lab.ntt.co.jp>
Signed-off-by: Kees Cook <keescook@chromium.org>
It's not just GEN9 platforms that allow for pipes to be disabled via
the DFSM register, but all later platforms as well.
v2: drop pointless parentheses (Ville)
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211192545.140081-1-bob.j.paauwe@intel.com
The DDB allocation algorithm currently used by the driver grants each
plane a very small minimum allocation of DDB blocks and then divies up
all of the remaining blocks based on the percentage of the total data
rate that the plane makes up. It turns out that this proportional
allocation approach is overly-generous with the larger planes and can
leave very small planes wthout a big enough allocation to even hit their
level 0 watermark requirements (especially on APL, which has a smaller
DDB in general than other gen9 platforms). Or there can be situations
where the smallest planes hit a lower watermark level than they should
have been able to hit with a more equitable division of DDB blocks, thus
limiting the overall system sleep state that can be achieved.
The bspec now describes an alternate algorithm that can be used to
overcome these types of issues. With the new algorithm, we calculate
all plane watermark values for all wm levels first, then go back and
partition a pipe's DDB space second. The DDB allocation will calculate
what the highest watermark level that can be achieved on *all* active
planes, and then grant the blocks necessary to hit that level to each
plane. Any remaining blocks are then divided up proportionally
according to data rate, similar to the old algorithm.
There was a previous attempt to implement this algorithm a couple years
ago in bb9d85f6e9 ("drm/i915/skl: New ddb allocation algorithm"), but
some regressions were reported, the patch was reverted, and nobody
ever got around to figuring out exactly where the bug was in that
version. Our watermark code has evolved significantly in the meantime,
but we're still getting bug reports caused by the unfair proportional
algorithm, so let's give this another shot.
v2:
- Make sure cursor allocation stays constant and fixed at the end of
the pipe allocation.
- Fix some watermark level iterators that weren't handling the max
level.
v3:
- Ensure we don't leave any DDB blocks unused by using DIV_ROUND_UP+min
to calculate the extra blocks for each plane. (Ville)
- Replace a while() loop with a for() loop to be more consistent with
surrounding code. (Ville)
- Clean unattainable watermark levels with memset rather than directly
clearing the member fields. Also do the same for the transition
watermark values if they can't be achieved. (Ville)
- Drop min_disp_buf_needed calculations in skl_compute_plane_wm() since
the results are no longer needed or used. (Ville)
- Drop skl_latency[0] != 0 sanity check; both watermark methods already
account for an invalid 0 latency by returning FP_16_16_MAX. (Ville)
v4:
- Break DDB allocation loop when total_data_rate=0 rather than
alloc_size=0. If total_data_rate has dropped to 0, all remaining
planes are disabled, which isn't true for alloc_size (we might just
have not had any remaining blocks to hand out). Plus
total_data_rate=0 is the case we need to avoid to a prevent a
div-by-0. (Ville)
- s/DIV_ROUND_UP/DIV64_U64_ROUND_UP/ to prevent 32-bit breakage (Ville)
v5:
- Don't forget to move 'start' pointer forward for UV surface when
setting plane DDB boundaries. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105458
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211173107.11068-2-matthew.d.roper@intel.com
The bspec gives an if/else chain for choosing whether to use "method 1"
or "method 2" for calculating the watermark "Selected Result Blocks"
value for a plane. One of the branches of the if chain is:
"Else If ('plane buffer allocation' is known and (plane buffer
allocation / plane blocks per line) >=1)"
Since our driver currently calculates DDB allocations first and the
actual watermark values second, the plane buffer allocation is known at
this point in our code and we include this test in our driver's logic.
However we plan to soon move to a "watermarks first, ddb allocation
second" sequence where we won't know the DDB allocation at this point.
Let's drop this arm of the if/else statement (effectively considering
the DDB allocation unknown) as an independent patch so that any
regressions can be more accurately bisected to either the different
watermark value (in this patch) or the new DDB allocation (in the next
patch).
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211173107.11068-1-matthew.d.roper@intel.com
null_blk_zoned creation fails if the number of zones specified is equal to or is
smaller than 64 due to a memory allocation failure in blk_alloc_zones(). With
such a small number of zones, the required memory size for all zones descriptors
fits in a single page, and the page order for alloc_pages_node() is zero. Allow
this value in blk_alloc_zones() for the allocation to succeed.
Fixes: bf50545696 "block: Introduce blk_revalidate_disk_zones()"
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
- Adding new notifier block (struct mlx5_nb) monitor_counters_nb
for handeling MONITOR_COUNTER new event type.
- Adding work queue element: monitor_counters_work for re-arm and
update stats.
- We re-queue the update stat work, only when working over firmware
that doesn't support the monitored counters.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
new file monitor_stats.c for the new API.
add arm_monitor_counter new command support.
add set_monitor_counter new command support.
The device can monitor specific counters and provide an event to notify
when these counters are changed.
The monitoring is done in best effort manner where the minimum
notification period is 200 ms, however when the device is loaded, the
notification might be delayed.
To configure the required counters to be monitored, the
SET_MONITOR_COUNTER command shall be used with a list of counters to be
monitored.
The device firmware can monitor up to HCA_CAP.max_num_of_monitor_counters.
The configuration is done based on counter type (such as ppcnt, q counter,
etc) and additional param according to the type of counter selected.
Upon monitor counter change, the device will generate
Monitor_Counter_Change event.
The device will not generate new events unless the driver re-arms the
monitoring functionality, using the ARM_MONITOR_COUNTER command.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
PPCNT is not supported if PCAM access reg is supported and ppcnt bit is clear.
Signed-off-by: Eyal Davidovich <eyald@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Writing 64B CQEs to 128B cache lines results in a RMW operation. Padding
the CQEs to 128B if possible improves performance on 128B cache line
systems like PPC.
Testing on PPC showed up to a 24% improvement in small packet throughput
vs the default behavior, depending on the workload and system topology.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently a flow is associated with a single encap structure. The FW
extended destination features enables the driver to associate a flow
with multiple encap instances.
Change the encap id field from a flow scope to a per destination value
in the flow attributes struct. Use the encaps array to associate a flow
table entry with multiple encap entries.
Update the neigh logic to offload only if all encapsulations used in a
flow are connected, and un-offload upon the first one disconnected.
Note that the driver can now support up to two encap destinations.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently a flow can be associated with a single encap entry. The
extended destination feature enables the driver to configure multiple
encap entries per flow.
Change the encap flow association field to array as a pre-step towards
supporting multiple encap destinations. Use only the first array
element, with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the driver can support only a single TC tunnel_set action.
Change the tunnel info fields to arrays, as a pre-step to support
multiple encapsulations for a single flow, with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
A rule with the following actions is split to a two level FDB:
1. Forward to local mirror vport
2. Header rewrite
3. Forward to local vport
In the first level flow table, forward the packet to the local port and
forward the packet to the second level flow table for header rewrite and
local port forwarding. This configuration fails when mirroring to a
remote encapsulated destination because currently an FTE cannot support
encap and table destinations.
Use the extended destination capabilities to configure the first level
flow table with a multi-destination FTE to the uplink and second level
table and the second level flow table for the header rewrite and local
port forwarding.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the FTE encap flag applies to all destinations.
To support mirroring encapsulated traffic to a local port the driver
split the two destinations to two flow table entries:
Table#0: - FWD to the local vport
- Goto table#1
Table#1: - Encap and FWD to wire
The firmware extended destination capabilities enable the driver to set
an encapsulation flag per destination.
Remove the split logic and use the extended destination mechanism
instead.
Note that split technique is still required for pedit and VLAN push
scenarios.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently a FW syndrome is emitted if the driver configures a
multi-destination FTE where the first destination is a tunneled uplink
port and the second destination is a local vPort.
Support this scenario by creating a multi-destination FTE using the
firmware's extended destination capabilities.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Flow attr reformat action bit is moved from the global action bits to a
per destination flags field, as a pre-step for adding additional flags
to support encapsulation properties per destination, with no
functionality change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the eswitch flow attr structure stores each destination
specific property in its own specific array.
Group them in an array of destination structures as a pre-step towards
adding additional destination specific field properties.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The mirror count esw attributes field is used to determine if splitting
the rule to two FTEs is required while programming e-switch mirroring.
Rename it to split count, making it clearer with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently the driver identifies identical vport destinations by
comparing the vport ID. The FW extended destination feature enables the
driver to forward the packet to the same vport with multiple
encapsulation properties.
Change the vport destination comparison logic to compare
the encapsulation properties in addition to the vport ID.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Initialize ib_device_ops with the supported operations using
ib_set_device_ops().
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Initialize ib_device_ops with the supported operations using
ib_set_device_ops().
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Initialize ib_device_ops with the supported operations using
ib_set_device_ops().
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Initialize ib_device_ops with the supported operations using
ib_set_device_ops().
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Initialize ib_device_ops with the supported operations using
ib_set_device_ops().
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Initialize ib_device_ops with the supported operations using
ib_set_device_ops().
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
