Add DRM bridge driver for TOSHIBA TC358764 chip used in LCD panel
for Samsung Exynos5250-based Arndale board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add regulator driver for MAX8952 PMIC chip used on Samsung UniversalC210
board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
According to Dave, once you've started an L2T flush, all L2T accesses
will be blocked until the flush completes. This fixes a consistent
3-4ms stall between the ioctl and running the job, and 3DMMES Taiji
goes from 27fps to 110fps.
v2: Leave a note about why we don't need to wait for completion.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 57692c94dc ("drm/v3d: Introduce a new DRM driver for Broadcom V3D V3.x+")
Reviewed-by: Dave Emett <david.emett@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203222438.25417-4-eric@anholt.net
This is the write combiner for TMU writes. You're supposed to flush
that at job end if you had dirtied any cachelines. Flushing it at job
start then doesn't make any sense.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 57692c94dc ("drm/v3d: Introduce a new DRM driver for Broadcom V3D V3.x+")
Reviewed-by: Dave Emett <david.emett@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203222438.25417-3-eric@anholt.net
Right now, userspace doesn't do any L2T writes, but we should lay out
our expectations for how it works.
v2: Explicitly mention the VCD cache flushing requirements and that
we'll flush the other caches before each of the CLs.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203222438.25417-1-eric@anholt.net
Reviewed-by: Dave Emett <david.emett@broadcom.com>
SKL+ do not use crtc_state->update_wm_pre, so there is absolutely no
point it setting it. crtc_state->update_wm_pre only exists as a
temporary hack for pre-g4x platforms until we redo their
watermarks to be be atomic.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181113172330.26069-3-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
-----BEGIN PGP SIGNATURE-----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=irzk
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20181207' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Let's try this again...
We're finally happy with the DM livelock issue, and it's also passed
overnight testing and the corruption regression test. The end result
is much nicer now too, which is great.
Outside of that fix, there's a pull request for NVMe with two small
fixes, and a regression fix for BFQ from this merge window. The BFQ
fix looks bigger than it is, it's 90% comment updates"
* tag 'for-linus-20181207' of git://git.kernel.dk/linux-block:
blk-mq: punt failed direct issue to dispatch list
nvmet-rdma: fix response use after free
nvme: validate controller state before rescheduling keep alive
block, bfq: fix decrement of num_active_groups
Pull i2c fixes from Wolfram Sang:
"A set of driver bugfixes for the I2C subsystem"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: uniphier-f: fix violation of tLOW requirement for Fast-mode
i2c: uniphier: fix violation of tLOW requirement for Fast-mode
i2c: uniphier-f: fill TX-FIFO only in IRQ handler for repeated START
i2c: uniphier-f: fix timeout error after reading 8 bytes
i2c: scmi: Fix probe error on devices with an empty SMB0001 ACPI device node
i2c: axxia: properly handle master timeout
i2c: rcar: check bus state before reinitializing
i2c: nvidia-gpu: limit reads also for combined messages
i2c: nvidia-gpu: adhere to I2C fault codes
skl_compute_wm() wants to compare the old and new watermarks. Currently
it gets at the old watermarks via crtc->state, which is confusing since
it can point at either the old or the new state depending on where
in the sequence we are. In this case it is correct since we have not yet
swapped the states, but let's make it super clear what this is doing
by using the explicit old state.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181113172330.26069-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
If link is disabled, media_entity_remote_pad returns NULL, causing a
NULL pointer deference.
Ignore links that are not enabled instead.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a DMI match for the Mediacom Flexbook Edge 11, this is the same hw
as the Trekstor Primebook C11, so we use the same settings.
Reported-by: rmbg <alexofrichardmilitiabg@hotmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
dmaengine fixes for v4.20-rc6
- Fixing imx-sdma handling of channel terminations, this involves
reverting two commits and implement async termination
- Fix cppi dma channel deletion from pending list on stop
- Fix FIFO size for dw controller in Intel Merrifield
-----BEGIN PGP SIGNATURE-----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=qeTx
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.20-rc6' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Another pull request for dmaengine. We got bunch of fixes early this
week and all are tagged to stable. Hope this is last fix for this
cycle:
- Fix imx-sdma handling of channel terminations, this involves
reverting two commits and implement async termination
- Fix cppi dma channel deletion from pending list on stop
- Fix FIFO size for dw controller in Intel Merrifield"
* tag 'dmaengine-fix-4.20-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw: Fix FIFO size for Intel Merrifield
dmaengine: cppi41: delete channel from pending list when stop channel
dmaengine: imx-sdma: use GFP_NOWAIT for dma descriptor allocations
dmaengine: imx-sdma: implement channel termination via worker
Revert "dmaengine: imx-sdma: alloclate bd memory from dma pool"
Revert "dmaengine: imx-sdma: Use GFP_NOWAIT for dma allocations"
GNU linker's -z common-page-size's default value is based on the target
architecture. arch/x86/entry/vdso/Makefile sets it to the architecture
default, which is implicit and redundant. Drop it.
Fixes: 2aae950b21 ("x86_64: Add vDSO for x86-64 with gettimeofday/clock_gettime/getcpu")
Reported-by: Dmitry Golovin <dima@golovin.in>
Reported-by: Bill Wendling <morbo@google.com>
Suggested-by: Dmitry Golovin <dima@golovin.in>
Suggested-by: Rui Ueyama <ruiu@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Andy Lutomirski <luto@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Fangrui Song <maskray@google.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20181206191231.192355-1-ndesaulniers@google.com
Link: https://bugs.llvm.org/show_bug.cgi?id=38774
Link: https://github.com/ClangBuiltLinux/linux/issues/31
The "L" AArch64 machine constraint, which we use for the "old" value in
an LL/SC cmpxchg(), generates an immediate that is suitable for a 64-bit
logical instruction. However, for cmpxchg() operations on types smaller
than 64 bits, this constraint can result in an invalid instruction which
is correctly rejected by GAS, such as EOR W1, W1, #0xffffffff.
Whilst we could special-case the constraint based on the cmpxchg size,
it's far easier to change the constraint to "K" and put up with using
a register for large 64-bit immediates. For out-of-line LL/SC atomics,
this is all moot anyway.
Reported-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Our percpu code is a bit of an inconsistent mess:
* It rolls its own xchg(), but reuses cmpxchg_local()
* It uses various different flavours of preempt_{enable,disable}()
* It returns values even for the non-returning RmW operations
* It makes no use of LSE atomics outside of the cmpxchg() ops
* There are individual macros for different sizes of access, but these
are all funneled through a switch statement rather than dispatched
directly to the relevant case
This patch rewrites the per-cpu operations to address these shortcomings.
Whilst the new code is a lot cleaner, the big advantage is that we can
use the non-returning ST- atomic instructions when we have LSE.
Signed-off-by: Will Deacon <will.deacon@arm.com>
The CAS instructions implicitly access only the relevant bits of the "old"
argument, so there is no need for explicit masking via type-casting as
there is in the LL/SC implementation.
Move the casting into the LL/SC code and remove it altogether for the LSE
implementation.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Our atomic instructions (either LSE atomics of LDXR/STXR sequences)
natively support byte, half-word, word and double-word memory accesses
so there is no need to mask the data register prior to being stored.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Earlier attempt to move am335x mcasp to probe with ti-sysc
interconnect target module caused audio to stop working and and
the dts changes were reverted by commit 5d2632a577 ("ARM: dts:
Revert am335x mcasp ti-sysc changes").
Turns out we were missing the l3 data port ranges for mcasp. This
caused mcasp dma to attempt to use wrong port address. So let's
try again essentially reverting the earlier revert and adding the
missing l3 data port ranges.
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It was noticed that unbinding and rebinding the KSZ8851 ethernet
resulted in the driver reporting "failed to read device ID" at probe.
Probing the reset line with a 'scope while repeatedly attempting to
bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is
constantly held at zero, meaning the device is held in reset, and
does not respond on the SPI bus.
Experimentation with the startup delay on the regulator set to 50ms
shows that the reset is positively released after 20ms.
Schematics for this board are not available, and the traces are buried
in the inner layers of the board which makes tracing where the RSTN pin
extremely difficult. We can only guess that the RSTN pin is wired to a
reset generator chip driven off the ethernet supply, which fits the
observed behaviour.
Include this delay in the regulator startup delay - effectively
treating the reset as a "supply stable" indicator.
This can not be modelled as a delay in the KSZ8851 driver since the
reset generation is board specific - if the RSTN pin had been wired to
a GPIO, reset could be released earlier via the already provided support
in the KSZ8851 driver.
This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based
on Blaze schematics that should be very close to SDP4430:
TPS22902YFPR is used as the regulator switch (gpio48 controlled):
Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV.
(SCH Note: Threshold set at 90%. Vsense: 0.405V).
According to the TPS3808 data sheet the RESET delay time when Ct is
open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated with notes from schematics from Peter]
Signed-off-by: Tony Lindgren <tony@atomide.com>
When a micro SD card is inserted in the PDU001 card cage, the card
detection switch is opened and the corresponding GPIO input is driven
by a pull-up. Hence change the active level of the card detection
input from low to high.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since commit 1137ceee76 ("ARM: OMAP1: ams-delta: Don't request unused
GPIOs"), on-board audio has appeared muted. Believed to be unused GPIO
pin "hookflash1", apparently set high regardless of the corresponding
bit of "latch2" port attempted to be set low during .init_machine(),
has been identified as the reason.
According to Amstrad E3 wiki, the purpose of the pin hasn't been
clearly identified. Original Amstrad software used to produce a high
pulse on it when the phone was taken off hook or recall was pressed.
With the current finding, we can assume the pin provides a kind of
audio mute function.
Proper resolution of the issue should be done in two steps:
- resolution of an issue with the pin state not reflecting the value
the corresponding bit of the port was attempted to be initialized
with,
- extension of on-board audio driver with a new control.
For now, rename the pin to "audio_mute" to reflect its function and,
as a quick fix, hogg it as output low so on-board audio can produce
audible sound again.
Fixes: 1137ceee76 ("ARM: OMAP1: ams-delta: Don't request unused GPIOs")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5's Super-Speed USB port has a software mailbox register
that needs to be fed with VBUS and ID events from an external
VBUS/ID comparator.
Without this, Host role will not work correctly.
Fixes: 656c1a65ab ("ARM: dts: omap5: enable OTG role for DWC3 controller")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some new variants require updated firmware.
V2: add MODULE_FIRMWARE for new firmwares
Reviewed-by: Huang Rui <ray.huang@amd.com> (v1)
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Previously, there are too many hacked stuffs such as `__FSIO_1',
`lstgrp_noio', `lstgrp_io' out there in `z_erofs_vle_submit_all'.
Revisit the whole process by properly introducing jobqueue to
represent each type of queued workgroups, furthermore hide all of
crazyness behind independent separated functions.
After this patch, 2 independent jobqueues exist if managed cache
is enabled, or 1 jobqueue if disabled.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By design, workgroups are queued in the form of linked lists.
Previously, it points to the next `z_erofs_vle_workgroup',
which isn't flexible enough to simplify `z_erofs_vle_submit_all'.
Let's fix it by pointing to the next `owned_workgrp_t' and use
container_of to get its coresponding `z_erofs_vle_workgroup'.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, there are two kinds of compressed pages in erofs:
1) file pages for the in-place decompression and
2) managed pages for cached decompression.
Both are all stored in grp->compressed_pages[].
For managed pages, they could already exist or could be preloaded
in this round, including the following cases in detail:
1) Already valid (loaded in some previous round);
2) PAGE_UNALLOCATED, should be allocated at the time of submission;
3) Just found in the managed cache, and with an extra page ref.
Currently, 1) and 3) can be distinguishable by lock_page and
checking its PG_private, which is guaranteed by the reclaim path,
but it's better to do a double check by using an extra tag.
This patch reworks the preload flow by introducing such the tag
by using tagged pointer, too many #ifdefs are removed as well.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, the submission flow works with cached compressed pages
reclaim path in a tricky way, and it could be buggy if the reclaim
path changes later without such tricky restrictions. For example,
currently one PagePrivate(page) is evaluated without taking page
lock (it only follows a wait_for_page_locked which closes such race)
and no handling solves the potential page truncation case.
In addition, it's also full of #ifdefs in the function, which
is hard to understand and maintain. this patch fixes them all.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In practice, in order to do cached decompression rather than reuse
them for in-place decompression and make full use of pages in
page_pool instead of allocating as much as possible, an unallocated
placeholder was introduce to mark all in compressed_pages[] and
they will be replaced at the time of submission.
Previously EROFS_UNALLOCATED_CACHED_PAGE was included in internal.h,
which is unnecessary since it's only internally used in decompression
subsystem, move it to unzip_vle.c and rename it to PAGE_UNALLOCATED.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces MNGD_MAPPING to wrap up
sbi->managed_cache->i_mapping, which will be used
to solve too many #ifdefs in a single function.
No logic changes.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The root cause is the race as follows:
Thread #0 Thread #1
z_erofs_vle_unzip_kickoff z_erofs_submit_and_unzip
struct z_erofs_vle_unzip_io io[]
atomic_add_return()
wait_event()
[end of function]
wake_up()
Fix it by taking the waitqueue lock between atomic_add_return and
wake_up to close such the race.
kernel message:
Unable to handle kernel paging request at virtual address 97f7052caa1303dc
...
Workqueue: kverityd verity_work
task: ffffffe32bcb8000 task.stack: ffffffe3298a0000
PC is at __wake_up_common+0x48/0xa8
LR is at __wake_up+0x3c/0x58
...
Call trace:
...
[<ffffff94a08ff648>] __wake_up_common+0x48/0xa8
[<ffffff94a08ff8b8>] __wake_up+0x3c/0x58
[<ffffff94a0c11b60>] z_erofs_vle_unzip_kickoff+0x40/0x64
[<ffffff94a0c118e4>] z_erofs_vle_read_endio+0x94/0x134
[<ffffff94a0c83c9c>] bio_endio+0xe4/0xf8
[<ffffff94a1076540>] dec_pending+0x134/0x32c
[<ffffff94a1076f28>] clone_endio+0x90/0xf4
[<ffffff94a0c83c9c>] bio_endio+0xe4/0xf8
[<ffffff94a1095024>] verity_work+0x210/0x368
[<ffffff94a08c4150>] process_one_work+0x188/0x4b4
[<ffffff94a08c45bc>] worker_thread+0x140/0x458
[<ffffff94a08cad48>] kthread+0xec/0x108
[<ffffff94a0883ab4>] ret_from_fork+0x10/0x1c
Code: d1006273 54000260 f9400804 b9400019 (b85fc081)
---[ end trace be9dde154f677cd1 ]---
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Gao Xiang <gaoxiang25@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 3b8c9f1cdf ("arm64: IPI each CPU after invalidating the
I-cache for kernel mappings"), a call to flush_icache_range() will use
an IPI to cross-call other online CPUs so that any stale instructions
are flushed from their pipelines. This triggers a WARN during the
hibernation resume path, where flush_icache_range() is called with
interrupts disabled and is therefore prone to deadlock:
| Disabling non-boot CPUs ...
| CPU1: shutdown
| psci: CPU1 killed.
| CPU2: shutdown
| psci: CPU2 killed.
| CPU3: shutdown
| psci: CPU3 killed.
| WARNING: CPU: 0 PID: 1 at ../kernel/smp.c:416 smp_call_function_many+0xd4/0x350
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.20.0-rc4 #1
Since all secondary CPUs have been taken offline prior to invalidating
the I-cache, there's actually no need for an IPI and we can simply call
__flush_icache_range() instead.
Cc: <stable@vger.kernel.org>
Fixes: 3b8c9f1cdf ("arm64: IPI each CPU after invalidating the I-cache for kernel mappings")
Reported-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Pull NVMe fixes from Christoph.
* 'nvme-4.20' of git://git.infradead.org/nvme:
nvmet-rdma: fix response use after free
nvme: validate controller state before rescheduling keep alive
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
While here, sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
While here, sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
