If the allocator fails before it has reached the target number of pages,
then we need to recheck that we're not seeking past the page buffer.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Clearing the GPIO_EN bit from chv_gpio_disable_free is a bad idea and
pinctrl-cherryview.c is the only Intel pinctrl driver doing something
like this.
Clearing the GPIO_EN bit means that if the pin was an output it is now
effectively floating. The datasheet is not clear what happens to pull ups /
downs in this case, but from testing it looks like these are disabled too,
also floating input pins.
One example where this is causing issues is the soc_button_array input
driver, this parses ACPI tables to create 2 platform devices for the
gpio_keys input driver. The list of GPIOs is passed through struct
gpio_keys_platform_data which uses gpio numbers rather then gpio_desc
pointers.
The buttons handled by this drivers short the pin to ground when pressed
and the volume buttons rely on the SoC's internal pull-up to pull the
pin high when the button is not pressed.
To get the gpio number, the soc_button_array code calls gpiod_get_index
followed by a desc_to_gpio call and then gpiod_put on the gpio_desc.
This last call causes chv_gpio_disable_free to clear the GPIO_EN bit.
When the gpio_keys driver then loads next it gets the gpio_desc again
causing the GPIO_EN bit to be set again and immediately reads the GPIO
value which for the volume buttons reads 0 at this time, causing a spurious
press of the volume buttons to get reported.
Putting a small delay between the gpio_desc request and the read fixes
this, I assume that this is caused by the pull-up being temporarily
disabled while the GPIO_EN bit is cleared as the powerbutton which also
has its GPIO_EN bit cleared does not have this problem.
The soc_button_array code is not the only code temporarily requesting GPIOs
the DWC3 PCI code also does this, to set the enable and reset GPIOs for the
external phy, so that the code instantiating the ULPI phy can read the
vendor and product ID registers from the phy. These GPIOs are released
after this so that the PHY driver can claim and use them when it loads.
Another example of temporary GPIO usage would be a user-space set_gpio
utility using the userspace ioctls to set a GPIO as output value 0 or 1,
having the GPIO revert to floating as soon as this utility exits would
certainly be unexpected behavior.
One argument in favor of clearing the GPIO_EN bit is if the GPIO is going
to be muxed to another function after being released, but in that case
chv_pinmux_set_mux() already clears it.
TL;DR: Clearing the GPIO_EN bit from is a bad idea, this commit therefor
removes the clearing from chv_gpio_disable_free(), replacing it with code
to clear the interrupt-trigger condition so that the GPIO stops generating
interrupts when released, as pinctrl-baytrail.c does.
Note this commit adds a !chv_pad_locked() condition to the trigger clearing
call, which the original GPIO_EN clearing code was missing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This is a preparation patch for clearing the interrupt trigger from
chv_gpio_disable_free().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The RPC code is occasionally hanging when the receive code fails to
empty the socket buffer due to a partial read of the data. When we
convert that to an EAGAIN, it appears we occasionally leave data in the
socket. The fix is to just keep reading until the socket returns
EAGAIN/EWOULDBLOCK.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Cristian Marussi <cristian.marussi@arm.com>
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Commit 7d33c35815 ("mmc: sdhci-omap: Workaround for Errata i802")
disabled DCRC interrupts during tuning. This write to the interrupt
enable register gets overwritten in sdhci_prepare_data() and the
interrupt is not in fact disabled. Fix this by disabling the interrupt
in the host->ier variable.
Fixes: 7d33c35815 ("mmc: sdhci-omap: Workaround for Errata i802")
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This function was modified to support the information element extension
case (WLAN_EID_EXTENSION) in a manner that would result in an infinite
loop when going through set of IEs that include WLAN_EID_RIC_DATA and
contain an IE that is in the after_ric array. The only place where this
can currently happen is in mac80211 ieee80211_send_assoc() where
ieee80211_ie_split_ric() is called with after_ric[].
This can be triggered by valid data from user space nl80211
association/connect request (i.e., requiring GENL_UNS_ADMIN_PERM). The
only known application having an option to include WLAN_EID_RIC_DATA in
these requests is wpa_supplicant and it had a bug that prevented this
specific contents from being used (and because of that, not triggering
this kernel bug in an automated test case ap_ft_ric) and now that this
bug is fixed, it has a workaround to avoid this kernel issue.
WLAN_EID_RIC_DATA is currently used only for testing purposes, so this
does not cause significant harm for production use cases.
Fixes: 2512b1b18d ("mac80211: extend ieee80211_ie_split to support EXTENSION")
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no need to hold the list_lock when initializing the local
asd_list of a notifier. Remove the lock handling to simplify the code
and remove a potential LOCKDEP warning.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reported-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The autoexposure setup in the 1080p init array is redundant with the
default value of the sensor.
Remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Now that we have everything in place to compute the clock rate at runtime,
we can enable the 60fps framerate for the mode we tested it with.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We stopped re-applying the GT workarounds after engine reset since commit
59b449d5c8 ("drm/i915: Split out functions for different kinds of
workarounds").
Issue with this is that some of the GT workarounds live in the MMIO space
which gets lost during engine resets. So far the registers in 0x2xxx and
0xbxxx address range have been identified to be affected.
This losing of applied workarounds has obvious negative effects and can
even lead to hard system hangs (see the linked Bugzilla).
Rather than just restoring this re-application, because we have also
observed that it is not safe to just re-write all GT workarounds after
engine resets (GPU might be live and weird hardware states can happen),
we introduce a new class of per-engine workarounds and move only the
affected GT workarounds over.
Using the framework introduced in the previous patch, we therefore after
engine reset, re-apply only the workarounds living in the affected MMIO
address ranges.
v2:
* Move Wa_1406609255:icl to engine workarounds as well.
* Rename API. (Chris Wilson)
* Drop redundant IS_KABYLAKE. (Chris Wilson)
* Re-order engine wa/ init so latest platforms are first. (Rodrigo Vivi)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugzilla.freedesktop.org/show_bug.cgi?id=107945
Fixes: 59b449d5c8 ("drm/i915: Split out functions for different kinds of workarounds")
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203133341.10258-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 4a15c75c42)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The current code uses an algorithm to clamp the FPS values and round them
to the closest supported one that isn't really allows to be extended to
more than two values.
Rework it a bit to make it much easier to extend the amount of FPS options
we support.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To enable later verification of GT workaround state at various stages of
driver lifetime, we record the list of applicable ones per platforms to a
list, from which they are also applied.
The added data structure is a simple array of register, mask and value
items, which is allocated on demand as workarounds are added to the list.
This is a temporary implementation which later in the series gets fused
with the existing per context workaround list handling. It is separated at
this stage since the following patch fixes a bug which needs to be as easy
to backport as possible.
Also, since in the following patch we will be adding a new class of
workarounds (per engine) which can be applied from interrupt context, we
straight away make the provision for safe read-modify-write cycle.
v2:
* Change dev_priv to i915 along the init path. (Chris Wilson)
* API rename. (Chris Wilson)
v3:
* Remove explicit list size tracking in favour of growing the allocation
in power of two chunks. (Chris Wilson)
v4:
Chris Wilson:
* Change wa_list_finish to early return.
* Copy workarounds using the compiler for static checking.
* Do not bother zeroing unused entries.
* Re-order struct i915_wa_list.
v5:
* kmalloc_array.
* Whitespace cleanup.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181203133319.10174-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 25d140faaa)
Fixes: 59b449d5c8 ("drm/i915: Split out functions for different kinds of workarounds")
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
In the ov5640_try_frame_interval function, the ret variable actually holds
the frame rate index to use, which is represented by the enum
ov5640_frame_rate in the driver.
Make it more obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Now that we have moved the clock generation logic out of the bytes array,
these arrays are identical between the 15fps and 30fps variants.
Remove the duplicate entries, and convert the code accordingly.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The pixel clock rates were introduced to report the initially static clock
rate.
Since this is now handled dynamically, we can remove them entirely.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As a precaution, make sure we check event_len when copying to userspace.
Based on old feedback: https://lkml.kernel.org/r/542D9FE5.3010009@gmx.de
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jan Kara <jack@suse.cz>
The MIPI divider is also cleared as part of the clock setup sequence, so we
can remove that code.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The OV5640_SCLK2X_ROOT_DIVIDER_DEFAULT and OV5640_SCLK_ROOT_DIVIDER_DEFAULT
defines represent exactly the same setup, and are at the same value, than
the more consistent with the rest of the driver OV5640_SCLK2X_ROOT_DIV and
OV5640_SCLK_ROOT_DIV.
Remove them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Part of the hardcoded initialization sequence is to set up the proper clock
dividers. However, this is now done dynamically through proper code and as
such, the static one is now redundant.
Let's remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The clock structure for the PCLK is quite obscure in the documentation, and
was hardcoded through the bytes array of each and every mode.
This is troublesome, since we cannot adjust it at runtime based on other
parameters (such as the number of bytes per pixel), and we can't support
either framerates that have not been used by the various vendors, since we
don't have the needed initialization sequence.
We can however understand how the clock tree works, and then implement some
functions to derive the various parameters from a given rate. And now that
those parameters are calculated at runtime, we can remove them from the
initialization sequence.
The modes also gained a new parameter which is the clock that they are
running at, from the register writes they were doing, so for now the switch
to the new algorithm should be transparent.
Co-Developed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Adam Ford <aford173@gmail.com> #imx6dq
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The set_fmt operations updates the sensor format only when the image format
is changed. When only the image sizes gets changed, the format do not get
updated causing the sensor to always report the one that was previously in
use.
Without this patch, updating frame size only fails:
[fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:srgb xfer:srgb ...]
With this patch applied:
[fmt:UYVY8_2X8/1024x768@1/30 field:none colorspace:srgb xfer:srgb ...]
Fixes: 6949d86477 ("media: ov5640: do not change mode if format or frame interval is unchanged")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx6 w/ CSI2 interface on 4.19.6 and 4.20-RC5
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The chip can be configured to output data transitions on the
rising or falling edge of PIXCLK (Datasheet R58:1[9]), default is on the
falling edge.
Parsing the fw-node is made in a subfunction to bundle all (future)
dt-parsing / fw-parsing stuff.
[m.grzeschik@pengutronix.de: Fix inverting clock. INV_PIX_CLOCK bit is set
per default. Set bit to 0 (enable mask bit without value) to enable
falling edge sampling.]
[m.felsch@pengutronix.de: use fwnode helpers]
[m.felsch@pengutronix.de: mv fw parsing into own function]
[m.felsch@pengutronix.de: adapt commit msg]
[sakari.ailus@linux.intel.com: V4L2 API usage changes to compile
on media tree master]
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the pclk-sample property to the list of optional properties
for the mt9m111 camera sensor.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Replace the vague binding by a more verbose. Remove the remote property
from the example since the driver don't support such a property. Also
remove the bus-width property from the endpoint since the driver don't
take care of it.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch implements the framerate selection using the skipping and
readout power-modi features. The power-modi cut the framerate by half
and each context has an independent selection bit. The same applies to
the 2x skipping feature.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently set_fmt don't care about the streaming status, so the format
can be changed during streaming. This can lead into wrong behaviours.
Check if the device is already streaming and return -EBUSY to avoid
wrong behaviours.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add callback to check if we are already streaming. Now other callbacks
can check the state and return -EBUSY if we already streaming.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The imx274 driver uses regmap and the build will fail without it.
Fixes:
drivers/media/i2c/imx274.c:142:21: error: variable ‘imx274_regmap_config’ has initializer but incomplete type
static const struct regmap_config imx274_regmap_config = {
^~~~~~~~~~~~~
drivers/media/i2c/imx274.c:1869:19: error: implicit declaration of function ‘devm_regmap_init_i2c’ [-Werror=implicit-function-declaration]
imx274->regmap = devm_regmap_init_i2c(client, &imx274_regmap_config);
^~~~~~~~~~~~~~~~~~~~
and others.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_ctrl_handler_init() expects a hint of how many controls this
handler is expected to refer to. Since this number here is always 4,
let's pass exactly 4.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
imx274_read_reg() takes a u8 pointer ("reg") and casts it to pass it
to regmap_read(), which takes an unsigned int pointer. This results in
a corrupted stack and random crashes.
Fixes: 0985dd306f ("media: imx274: V4l2 driver for Sony imx274 CMOS sensor")
Cc: stable@vger.kernel.org # for 4.15 and up
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
NullFunc packets should never be duplicate just like
QoS-NullFunc packets.
We saw a client that enters / exits power save with
NullFunc frames (and not with QoS-NullFunc) despite the
fact that the association supports HT.
This specific client also re-uses a non-zero sequence number
for different NullFunc frames.
At some point, the client had to send a retransmission of
the NullFunc frame and we dropped it, leading to a
misalignment in the power save state.
Fix this by never consider a NullFunc frame as duplicate,
just like we do for QoS NullFunc frames.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201449
CC: <stable@vger.kernel.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some Sony camera sensors have same test pattern
definitions, this patch unify the pattern naming
to make it more clear to the userspace.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
current imx355 test pattern order in ctrl menu
is not correct, this patch fixes it.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
current imx319 test pattern order in ctrl menu
is not correct, this patch fixes it.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On a imx6q-wandboard the following warnings are observed:
[ 4.327794] video-mux 20e0000.iomuxc-gpr:ipu1_csi0_mux: bad remote port parent
[ 4.336118] video-mux 20e0000.iomuxc-gpr:ipu2_csi1_mux: bad remote port parent
As explained by Philipp Zabel:
"There are empty endpoint nodes (without remote-endpoint property)
labeled ipu1_csi[01]_mux_from_parallel_sensor in the i.MX6 device trees
for board DT implementers' convenience. See commit 2539f517ac ("ARM:
dts: imx6qdl: Add video multiplexers, mipi_csi, and their connections")."
So demote the warning to debug level and make the wording a bit
less misleading.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the buffered broadcast queue contains packets, letting new packets bypass
that queue can lead to heavy reordering, since the driver is probably throttling
transmission of buffered multicast packets after beacons.
Keep buffering packets until the buffer has been cleared (and no client
is in powersave mode).
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make it behave like regular ieee80211_tx_status calls, except for the lack of
filtered frame processing.
This fixes spurious low-ack triggered disconnections with powersave clients
connected to an AP.
Fixes: f027c2aca0 ("mac80211: add ieee80211_tx_status_noskb")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds the device node of the GCE hardware for CMDQ module.
Signed-off-by: Houlong Wei <houlong.wei@mediatek.com>
Signed-off-by: HS Liao <hs.liao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
It seems like when ldsem_down_read() fails with timeout, it misses
update for sem->wait_readers. By that reason, when writer finally
releases write end of the semaphore __ldsem_wake_readers() does adjust
sem->count with wrong value:
sem->wait_readers * (LDSEM_ACTIVE_BIAS - LDSEM_WAIT_BIAS)
I.e, if update comes with 1 missed wait_readers decrement, sem->count
will be 0x100000001 which means that there is active reader and it'll
make any further writer to fail in acquiring the semaphore.
It looks like, this is a dead-code, because ldsem_down_read() is never
called with timeout different than MAX_SCHEDULE_TIMEOUT, so it might be
worth to delete timeout parameter and error path fall-back..
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure under CONFIG_LOCKDEP that each change to line discipline
is done with held write semaphor.
Otherwise potential reader will have a good time dereferencing
incomplete/uninitialized ldisc.
An exception here is tty_ldisc_open(), as it's called without ldisc_sem
locked by tty_init_dev() => tty_ldisc_setup() for the tty->link.
It seem valid as tty_init_dev() will call tty_driver_install_tty()
which will find ops->install(). Install will establish tty->link in
pty_common_install(), just after allocation of slave tty with
alloc_tty_struct(). So, no one should have a reference to slave pty yet.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason ldsem has its own lockdep wrappers, make them go away.
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There might be situations where tty_ldisc_lock() has blocked, but there
is already IO on tty and it prevents line discipline changes.
It might theoretically turn into dead-lock.
Basically, provide more priority to pending tty_ldisc_lock() than to
servicing reads/writes over tty.
User-visible issue was reported by Mikulas where on pa-risc with
Debian 5 reboot took either 80 seconds, 3 minutes or 3:25 after proper
locking in tty_reopen().
Cc: Jiri Slaby <jslaby@suse.com>
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_ldisc_reinit() doesn't race with neither tty_ldisc_hangup()
nor set_ldisc() nor tty_ldisc_release() as they use tty lock.
But it races with anyone who expects line discipline to be the same
after hoding read semaphore in tty_ldisc_ref().
We've seen the following crash on v4.9.108 stable:
BUG: unable to handle kernel paging request at 0000000000002260
IP: [..] n_tty_receive_buf_common+0x5f/0x86d
Workqueue: events_unbound flush_to_ldisc
Call Trace:
[..] n_tty_receive_buf2
[..] tty_ldisc_receive_buf
[..] flush_to_ldisc
[..] process_one_work
[..] worker_thread
[..] kthread
[..] ret_from_fork
tty_ldisc_reinit() should be called with ldisc_sem hold for writing,
which will protect any reader against line discipline changes.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: stable@vger.kernel.org # b027e2298b ("tty: fix data race between tty_init_dev and flush of buf")
Reviewed-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: syzbot+3aa9784721dfb90e984d@syzkaller.appspotmail.com
Tested-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Tested-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ldsem_down_read() will sleep if there is pending writer in the queue.
If the writer times out, readers in the queue should be woken up,
otherwise they may miss a chance to acquire the semaphore until the last
active reader will do ldsem_up_read().
There was a couple of reports where there was one active reader and
other readers soft locked up:
Showing all locks held in the system:
2 locks held by khungtaskd/17:
#0: (rcu_read_lock){......}, at: watchdog+0x124/0x6d1
#1: (tasklist_lock){.+.+..}, at: debug_show_all_locks+0x72/0x2d3
2 locks held by askfirst/123:
#0: (&tty->ldisc_sem){.+.+.+}, at: ldsem_down_read+0x46/0x58
#1: (&ldata->atomic_read_lock){+.+...}, at: n_tty_read+0x115/0xbe4
Prevent readers wait for active readers to release ldisc semaphore.
Link: lkml.kernel.org/r/20171121132855.ajdv4k6swzhvktl6@wfg-t540p.sh.intel.com
Link: lkml.kernel.org/r/20180907045041.GF1110@shao2-debian
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current oversampling rate of 512 means that for 48 kHz 16 bit
stereo, the MCLK is running at the same rate as the module clock,
so there is no head room to support higher sampling rates. The codec
however supports up to 192 kHz for playback.
This patch drops the oversampling rate from 512 to 128, so that 192 kHz
audio can be played back directly without downsampling. Ideally we
should be using different oversampling rates for different sampling
rates, but that's not possible without a platform-specific machine
driver.
Fixes: 870f1bd1f5 ("ARM: dts: sun8i: Add audio codec, dai and card for A33")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
All the audio interfaces on Allwinner SoCs need to change their module
clocks during operation, to switch between support for 44.1 kHz and 48
kHz family sample rates. The clock rate for the module clocks is
governed by their upstream audio PLL. The module clocks themselves only
have a gate, and sometimes a divider or mux. Thus any rate changes need
to be propagated upstream.
Set the CLK_SET_RATE_PARENT flag for all audio module clocks to achieve
this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
