This avoids a situation in which we attempt to apply various fixups
that are not intended to handle implicit supervisor accesses from
user mode if we screw up in a way that causes this type of fault.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yu-cheng Yu <yu-cheng.yu@intel.com>
Link: http://lkml.kernel.org/r/9999f151d72ff352265f3274c5ab3a4105090f49.1542841400.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
All of the fault handling code now corrently checks user_mode(regs)
as needed, and nothing depends on the X86_PF_USER bit being munged.
Get rid of the sw_error code and use hw_error_code everywhere.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yu-cheng Yu <yu-cheng.yu@intel.com>
Link: http://lkml.kernel.org/r/078f5b8ae6e8c79ff8ee7345b5c476c45003e5ac.1542841400.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The T3/R40/V40 using the same sdk and config file in allwinner
sdk, it seem they are the same SOC just with different name, so
compatible with R40.
The t3-cqa3t-bv3 based on Allwinner T3 SoC, it has various connectors,
leds, buttons, and sell on:
https://item.taobao.com/item.htm?spm=2013.1.w4023-4203040713.25.62704cce7UCgLS&id=557154455330
It features:
- X-Powers AXP221s PMIC connected to i2c0
- 1/2 GB DDR3 DRAM
- 8 GB eMMC
- 2x USB 2.0 hosts
- 1x USB 2.0 OTG
- 2 LVDS connectors
- 24 bit RGB LCD connector
- HDMI output
- DVP camera interface (support 500w cmos camera)
- GPIO connectors
- 5 TTL uarts and 2 RS232 uarts
- 1 RS485 connector
- support i2c capacitive tp and usb infrared tp
- boot control, reset and user buttons
- 3.5mm headphone and 3.5mm mic jack
- 100M RJ45
- micro SD card slot
- DC power jack
- RCT power slot
- 1 CVBS TVIN
- 1 CVBS TVOUT
- 2 customer leds
- 1 buzzer
- 1 minipcie
- I2C output
- SPI output
- PCM output
- wifi and bt connector reserved.
Board info can find here:
https://github.com/Axl-zhang/Allwinner-V40-T3-R40-manual
Signed-off-by: Hao Zhang <hao5781286@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
In some existing lantiq driver, the C codes include lantiq_soc.h
header file directly.
./arch/mips/include/asm/mach-lantiq/falcon/lantiq_soc.h
./arch/mips/include/asm/mach-lantiq/xway/lantiq_soc.h
Those drivers need to be extended to support more platform.
lantiq.h is added in include/linux/ to make it
globally available and provides some wrapper codes.
Signed-off-by: Songjun Wu <songjun.wu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit aaf9978c3c.
Quoting Peter:
There is a HID feature report called "Resolution Multiplier"
Described in the "Enhanced Wheel Support in Windows" doc and
the "USB HID Usage Tables" page 30.
http://download.microsoft.com/download/b/d/1/bd1f7ef4-7d72-419e-bc5c-9f79ad7bb66e/wheel.docxhttps://www.usb.org/sites/default/files/documents/hut1_12v2.pdf
This was new for Windows Vista, so we're only a decade behind here. I only
accidentally found this a few days ago while debugging a stuck button on a
Microsoft mouse.
The docs above describe it like this: a wheel control by default sends
value 1 per notch. If the resolution multiplier is active, the wheel is
expected to send a value of $multiplier per notch (e.g. MS Sculpt mouse) or
just send events more often, i.e. for less physical motion (e.g. MS Comfort
mouse).
For the latter, you need the right HW of course. The Sculpt mouse has
tactile wheel clicks, so nothing really changes. The Comfort mouse has
continuous motion with no tactile clicks. Similar to the free-wheeling
Logitech mice but without any inertia.
Note that the doc also says that Vista and onwards *always* enable this
feature where available.
An example HID definition looks like this:
Usage Page Generic Desktop (0x01)
Usage Resolution Multiplier (0x48)
Logical Minimum 0
Logical Maximum 1
Physical Minimum 1
Physical Maximum 16
Report Size 2 # in bits
Report Count 1
Feature (Data, Var, Abs)
So the actual bits have values 0 or 1 and that reflects real values 1 or 16.
We've only seen single-bits so far, so there's low-res and hi-res, but
nothing in between.
The multiplier is available for HID usages "Wheel" and "AC Pan" (horiz wheel).
Microsoft suggests that
> Vendors should ship their devices with smooth scrolling disabled and allow
> Windows to enable it. This ensures that the device works like a regular HID
> device on legacy operating systems that do not support smooth scrolling.
(see the wheel doc linked above)
The mice that we tested so far do reset on unplug.
Device Support looks to be all (?) Microsoft mice but nothing else
Not supported:
- Logitech G500s, G303
- Roccat Kone XTD
- all the cheap Lenovo, HP, Dell, Logitech USB mice that come with a
workstation that I could find don't have it.
- Etekcity something something
- Razer Imperator
Supported:
- Microsoft Comfort Optical Mouse 3000 - yes, physical: 1:4
- Microsoft Sculpt Ergonomic Mouse - yes, physical: 1:12
- Microsoft Surface mouse - yes, physical: 1:4
So again, I think this is really just available on Microsoft mice, but
probably all decent MS mice released over the last decade.
Looking at the hardware itself:
- no noticeable notches in the weel
- low-res: 18 events per 360deg rotation (click angle 20 deg)
- high-res: 72 events per 360deg → matches multiplier of 4
- I can feel the notches during wheel turns
- low-res: 24 events per 360 deg rotation (click angle 15 deg)
- horiz wheel is tilt-based, continuous output value 1
- high-res: 24 events per 360deg with value 12 → matches multiplier of 12
- horiz wheel output rate doubles/triples?, values is 3
- It's a touch strip, not a wheel so no notches
- high-res: events have value 4 instead of 1
a bit strange given that it doesn't actually have notches.
Ok, why is this an issue for the current API? First, because the logitech
multiplier used in Harry's patches looks suspiciously like the Resolution
Multiplier so I think we should assume it's the same thing. Nestor, can you
shed some light on that?
- `REL_WHEEL` is defined as the number of notches, emulated where needed.
- `REL_WHEEL_HI_RES` is the movement of the user's finger in microns.
- `WM_MOUSEWHEEL` (Windows) is is a multiple of 120, defined as "the threshold
for action to be taken and one such action"
https://docs.microsoft.com/en-us/windows/desktop/inputdev/wm-mousewheel
If the multiplier is set to M, this means we need an accumulated value of M
until we can claim there was a wheel click. So after enabling the multiplier
and setting it to the maximum (like Windows):
- M units are 15deg rotation → 1 unit is 2620/M micron (see below). This is
the `REL_WHEEL_HI_RES` value.
- wheel diameter 20mm: 15 deg rotation is 2.62mm, 2620 micron (pi * 20mm /
(360deg/15deg))
- For every M units accumulated, send one `REL_WHEEL` event
The problem here is that we've now hardcoded 20mm/15 deg into the kernel and
we have no way of getting the size of the wheel or the click angle into the
kernel.
In userspace we now have to undo the kernel's calculation. If our click angle
is e.g. 20 degree we have to undo the (lossy) calculation from the kernel and
calculate the correct angle instead. This also means the 15 is a hardcoded
option forever and cannot be changed.
In hid-logitech-hidpp.c, the microns per unit is hardcoded per device.
Harry, did you measure those by hand? We'd need to update the kernel for
every device and there are 10 years worth of devices from MS alone.
The multiplier default is 8 which is in the right ballpark, so I'm pretty
sure this is the same as the Resolution Multiplier, just in HID++ lingo. And
given that the 120 magic factor is what Windows uses in the end, I can't
imagine Logitech rolling their own thing here. Nestor?
And we're already fairly inaccurate with the microns anyway. The MX Anywhere
2S has a click angle of 20 degrees (18 stops) and a 17mm wheel, so a wheel
notch is approximately 2.67mm, one event at multiplier 8 (1/8 of a notch)
would be 334 micron. That's only 80% of the fallback value of 406 in the
kernel. Multiplier 6 gives us 445micron (10% off). I'm assuming multiplier 7
doesn't exist because it's not a factor of 120.
Summary:
Best option may be to simply do what Windows is doing, all the HW manufacturers
have to use that approach after all. Switch `REL_WHEEL_HI_RES` to report in
fractions of 120, with 120 being one notch and divide that by the multiplier
for the actual events. So e.g. the Logitech multiplier 8 would send value 15
for each event in hi-res mode. This can be converted in userspace to
whatever userspace needs (combined with a hwdb there that tells you wheel
size/click angle/...).
Conflicts:
include/uapi/linux/input-event-codes.h -> I kept the new
reserved event in the code, so I had to adapt the revert
slightly
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 1ff2e1a44e.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 051dc9b057.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit d56ca9855b.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 3fe1d6bbcd.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 5fe2ccbef9.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 044ee89028.
It turns out the current API is not that compatible with
some Microsoft mice, so better start again from scratch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Harry Cutts <hcutts@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
if loopback_idev is NULL pointer, and the following access of
loopback_idev will trigger panic, which is same as BUG_ON
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
- Start using BPF maps in 'perf trace' for filters in the augmented syscalls
code, keeping the existing code for tracepoint filters so that we can switch
back and forth while getting everything BPFied (Arnaldo Carvalho de Melo)
- Suppress potential format-truncation warning in the PMU code (Ben Hutchings)
- Introduce 'perf bench epoll', with "wait" and "ctl" benchmarks (Davidlohr Bueso)
- Fix slowness due to -ffunction-section, do it by sorting the maps by name, so
avoiding the using rb_first/next to traverse all entries looking for a map name,
that with --ffunction-section gets to thousands of maps (Eric Saint-Etienne)
- Separate jvmti cmlr check (Jiri Olsa)
- Allow using the stepping when figuring out which JSON files to use for a x86
processor, so that Cascadelake server can be support, which has the same
cpuid as some other processor, being different only in the stepping (Kan Liang)
- Share code and output format for uregs and iregs 'perf script' output (Milian Wolff)
- Use perf_evsel__is_clocki() for clock events in 'perf stat' (Ravi Bangoria)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHQEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCW/YiKQAKCRCyPKLppCJ+
J3qLAPjy8imSBJP/odU0G/cvcAQ3nUXfv4c9j7+5iWmb4kJhAQCt+SyEhsnOqlwf
9XyquKIwcz05D7HlSDlRngL9Y7W3CQ==
=ncNT
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo-4.21-20181122' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
- Start using BPF maps in 'perf trace' for filters in the augmented syscalls
code, keeping the existing code for tracepoint filters so that we can switch
back and forth while getting everything BPFied (Arnaldo Carvalho de Melo)
- Suppress potential format-truncation warning in the PMU code (Ben Hutchings)
- Introduce 'perf bench epoll', with "wait" and "ctl" benchmarks (Davidlohr Bueso)
- Fix slowness due to -ffunction-section, do it by sorting the maps by name, so
avoiding the using rb_first/next to traverse all entries looking for a map name,
that with --ffunction-section gets to thousands of maps (Eric Saint-Etienne)
- Separate jvmti cmlr check (Jiri Olsa)
- Allow using the stepping when figuring out which JSON files to use for a x86
processor, so that Cascadelake server can be support, which has the same
cpuid as some other processor, being different only in the stepping (Kan Liang)
- Share code and output format for uregs and iregs 'perf script' output (Milian Wolff)
- Use perf_evsel__is_clocki() for clock events in 'perf stat' (Ravi Bangoria)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
MIPS' asm/mmzone.h includes the machine/platform mmzone.h
unconditionally, but since commit bb53fdf395 ("MIPS: c-r4k: Add
r4k_blast_scache_node for Loongson-3") is included by asm/rk4cache.h for
all r4k-style configs regardless of CONFIG_NEED_MULTIPLE_NODES.
This is problematic when CONFIG_NEED_MULTIPLE_NODES=n because both the
loongson3 & ip27 mmzone.h headers unconditionally define the NODE_DATA
preprocessor macro which is aready defined by linux/mmzone.h, resulting
in the following build error:
In file included from ./arch/mips/include/asm/mmzone.h:10,
from ./arch/mips/include/asm/r4kcache.h:23,
from arch/mips/mm/c-r4k.c:33:
./arch/mips/include/asm/mach-loongson64/mmzone.h:48: error: "NODE_DATA" redefined [-Werror]
#define NODE_DATA(n) (&__node_data[(n)]->pglist)
In file included from ./include/linux/topology.h:32,
from ./include/linux/irq.h:19,
from ./include/asm-generic/hardirq.h:13,
from ./arch/mips/include/asm/hardirq.h:16,
from ./include/linux/hardirq.h:9,
from arch/mips/mm/c-r4k.c:11:
./include/linux/mmzone.h:907: note: this is the location of the previous definition
#define NODE_DATA(nid) (&contig_page_data)
Resolve this by only including the machine mmzone.h when
CONFIG_NEED_MULTIPLE_NODES=y, which also removes the need for the empty
mach-generic version of the header which we delete.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: bb53fdf395 ("MIPS: c-r4k: Add r4k_blast_scache_node for Loongson-3")
Replaced dma_alloc_coherent + memset with dma_zalloc_coherent.
Signed-off-by: Sabyasachi Gupta <sabyasachi.linux@gmail.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/bnx2i/bnx2i_hwi.c: In function 'bnx2i_process_ofld_cmpl':
drivers/scsi/bnx2i/bnx2i_hwi.c:2430:6: warning:
variable 'cid_num' set but not used [-Wunused-but-set-variable]
It never used since commit
cf4e636385 ("[SCSI] bnx2i: Add bnx2i iSCSI driver.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Nilesh Javali <nilesh.javali@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
aha1542 is one of the last users of the legacy isa_*_to_bus APIs, which
also isn't portable enough. Convert it to the proper DMA mapping API.
Thanks to Ondrej Zary for testing and finding and fixing a crucial bug.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for MegaRAID Aero controller PCI IDs. Print a
message when a configurable secure type controller is encountered.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Display following warning message only upon detection of configurable
secure type controllers.
"HBA is in Configurable Secure mode"
[mkp: typos]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/libfc/fc_rport.c: In function 'fc_rport_recv_flogi_req':
drivers/scsi/libfc/fc_rport.c:866:18: warning:
variable 'disc' set but not used [-Wunused-but-set-variable]
It no used any more after
commit baa6719f90 ("libfc: Update rport reference counting")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The new emulate_pr backstore attribute allows for Persistent Reservation
and SCSI2 RESERVE/RELEASE support to be completely disabled. This can be
useful for scenarios such as:
- Ensuring ATS (Compare & Write) usage on recent VMware ESXi initiators.
- Allowing clustered (e.g. tcm-user) backends to block such requests,
avoiding the multi-node reservation state propagation.
When explicitly disabled, PR and RESERVE/RELEASE requests receive Invalid
Command Operation Code response sense data.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I fixed a bug by adding a dependency in the network driver, but that fix
caused a related bug in the SCSI driver:
WARNING: unmet direct dependencies detected for CHELSIO_T4
Depends on [m]: NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_CHELSIO [=y] && PCI [=y] && (IPV6 [=y] || IPV6 [=y]=n) && (THERMAL [=m] || !THERMAL [=m])
Selected by [y]:
- SCSI_CXGB4_ISCSI [=y] && SCSI_LOWLEVEL [=y] && SCSI [=y] && PCI [=y] && INET [=y] && (IPV6 [=y] || IPV6 [=y]=n)
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_init':
cxgb4_thermal.c:(.text+0x158): undefined reference to `thermal_zone_device_register'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_thermal.o: In function `cxgb4_thermal_remove':
cxgb4_thermal.c:(.text+0x1d8): undefined reference to `thermal_zone_device_unregister'
/git/arm-soc/Makefile:1042: recipe for target 'vmlinux' failed
The same dependency needs to be propagated here to make it work correctly
with CONFIG_THERMAL=m and SCSI_CXGB4_ISCSI=y. That change by itself causes
another problem with a circular dependency, as we use 'select NETDEVICES'.
This is something we really should not do anyway, as a driver symbol should
never select another major subsystem, so let's turn that into a 'depends
on'. I don't see any downsides of that, as NETDEVICES is only disabled in
rather obscure cases that are not relevant to the users of cxgb4i.
Fixes: e70a57fa59 ("cxgb4: fix thermal configuration dependencies")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UAPI Changes:
- Remove syncobj timeline support from drm.
Cross-subsystem Changes:
- Document canvas provider node in the DT bindings.
- Improve documentation for TPO TPG110 DT bindings.
Core Changes:
- Use explicit state in drm atomic functions.
- Add panel quirk for new GPD Win2 firmware.
- Add DRM_FORMAT_XYUV8888.
- Set the default import/export function in prime to drm_gem_prime_import/export.
- Add a separate drm_gem_object_funcs, to stop relying on dev->driver->*gem* functions.
- Make sure that tinydrm sets the virtual address also on imported buffers.
Driver Changes:
- Support active-low data enable signal in sun4i.
- Fix scaling in vc4.
- Use canvas provider node in meson.
- Remove unused variables in sti and qxl and cirrus.
- Add overlay plane support and primary plane scaling to meson.
- i2c fixes in drm/bridge/sii902x
- Fix mailbox read size in rockchip.
- Spelling fix in panel/s6d16d0.
- Remove unnecessary null check from qxl_bo_unref.
- Remove unused arguments from qxl_bo_pin.
- Fix qxl cursor pinning.
-----BEGIN PGP SIGNATURE-----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=elpS
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-11-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.21, part 2:
UAPI Changes:
- Remove syncobj timeline support from drm.
Cross-subsystem Changes:
- Document canvas provider node in the DT bindings.
- Improve documentation for TPO TPG110 DT bindings.
Core Changes:
- Use explicit state in drm atomic functions.
- Add panel quirk for new GPD Win2 firmware.
- Add DRM_FORMAT_XYUV8888.
- Set the default import/export function in prime to drm_gem_prime_import/export.
- Add a separate drm_gem_object_funcs, to stop relying on dev->driver->*gem* functions.
- Make sure that tinydrm sets the virtual address also on imported buffers.
Driver Changes:
- Support active-low data enable signal in sun4i.
- Fix scaling in vc4.
- Use canvas provider node in meson.
- Remove unused variables in sti and qxl and cirrus.
- Add overlay plane support and primary plane scaling to meson.
- i2c fixes in drm/bridge/sii902x
- Fix mailbox read size in rockchip.
- Spelling fix in panel/s6d16d0.
- Remove unnecessary null check from qxl_bo_unref.
- Remove unused arguments from qxl_bo_pin.
- Fix qxl cursor pinning.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9c0409e3-a85f-d2af-b4eb-baf1eb8bbae4@linux.intel.com
- OD fixes for powerplay
- Vega20 fixes
- KFD fix for Kaveri
- add missing firmware declaration for hainan (SI chip)
- Fix DC user experience regressions related to panels that support >8 bpc
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181121163647.2847-1-alexander.deucher@amd.com
The weak functions, strcmp_cpuid_str() and get_cpuid_str(), are defined
in pmu.c.
Most of the cpuid related functions, including *_cpuid_str()'s
declaration and platform specific definition, are in header.c/h.
To make the declaration and definition of all cpuid related functions in
a consistent place, move the weak functions to header.c.
There is no functional change.
Suggested-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Link: http://lkml.kernel.org/r/20181121164939.13482-1-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Perf can take minutes to parse an image when -ffunction-section is used.
This is especially true with the kernel image when it is compiled this
way, which is the arm64 default since the patcheset "Enable deadcode
elimination at link time".
Perf organize maps using a rbtree. Whenever perf finds a new symbols, it
first searches this rbtree for the map it belongs to, by strcmp()'aring
section names. When it finds the map with the right name, it uses it to
add the symbol. With a usual image there aren't so many maps but when
using -ffunction-section there's basically one map per function. With
the kernel image that's north of 40,000 maps. For most symbols perf has
to parses the entire rbtree to eventually create a new map and add it.
Consequently perf spends most of the time browsing a rbtree that keeps
getting larger.
This performance fix introduces a secondary rbtree that indexes maps
based on the section name.
Signed-off-by: Eric Saint-Etienne <eric.saint.etienne@oracle.com>
Reviewed-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Reviewed-by: David Aldridge <david.aldridge@oracle.com>
Reviewed-by: Rob Gardner <rob.gardner@oracle.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1542822679-25591-1-git-send-email-eric.saint.etienne@oracle.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The Compiled Method Load Record (cmlr) is JDK specific interface to
access JVM stack info. This makes the jvmti agent code not compile under
another jdk, which does not support that.
Separating jvmti cmlr check into special feature check, and adding
HAVE_JVMTI_CMLR macro to indicate that.
Mark cmlr code in jvmti/libjvmti.c with HAVE_JVMTI_CMLR, so we can
compile it on system without cmlr support.
This change makes the jvmti compile with java-1.8.0-ibm package. It's
without the line numbers support, but the rest works.
Adding NO_JVMTI_CMLR compile variable for testing.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ben Gainey <ben.gainey@arm.com>
Cc: Gustavo Luiz Duarte <gduarte@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/20181121154341.21521-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add JSON metrics (based on event list v1) for Cascadelake server
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/3ab97c73-c197-8555-1a35-b54636e667e6@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The perf tools cannot find the proper event list for the Cascadelake
server. Because the Cascadelake server and the Skylake server have the
same CPU model number, which are used by the perf tools to find the
event list.
The stepping for Skylake server is up to 4.
The stepping for Cascadelake server starts from 5.
The stepping can be used to distinguish between them.
The stepping is added in get_cpuid_str().
The stepping information for Skylake server is updated in mapfile.csv.
A x86 specific strcmp_cpuid_cmp() function is added to handle two CPUID
formats in mapfile.csv, "vendor-family-model-stepping" and
"vendor-family-model":
- If a cpuid-regular-expression from the mapfile.csv using the new
stepping format, a cpuid-string generated on the machine must include
stepping. Otherwise, it is a mismatch.
- If the cpuid-regular-expression using the old non-stepping format,
the stepping in the cpuid-string will be ignored.
The script, using environment string "PERF_CPUID" without stepping on
Skylake server, will be broken. If so, users must fix their scripts.
Committer notes:
Fixed this build error on centos:6 and debian:7:
arch/x86/util/header.c: In function 'is_full_cpuid':
arch/x86/util/header.c:82:39: error: declaration of 'cpuid' shadows a global declaration [-Werror=shadow]
arch/x86/util/header.c:12:1: error: shadowed declaration is here [-Werror=shadow]
arch/x86/util/header.c: In function 'strcmp_cpuid_str':
arch/x86/util/header.c:98:56: error: declaration of 'cpuid' shadows a global declaration [-Werror=shadow]
arch/x86/util/header.c:12:1: error: shadowed declaration is here [-Werror=shadow]
cc1: all warnings being treated as errors
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20181114212416.15665-1-kan.liang@linux.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We already have function to check if a given event is either
SW_CPU_CLOCK or SW_TASK_CLOCK. Utilize it.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Thomas Richter <tmricht@linux.vnet.ibm.com>
Cc: yuzhoujian@didichuxing.com
Link: http://lkml.kernel.org/r/20181115095533.16930-1-ravi.bangoria@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Depending on which functions are inlined in util/pmu.c, the snprintf()
calls in perf_pmu__parse_{scale,unit,per_pkg,snapshot}() might trigger a
warning:
util/pmu.c: In function 'pmu_aliases':
util/pmu.c:178:31: error: '%s' directive output may be truncated writing up to 255 bytes into a region of size between 0 and 4095 [-Werror=format-truncation=]
snprintf(path, PATH_MAX, "%s/%s.unit", dir, name);
^~
I found this when trying to build perf from Linux 3.16 with gcc 8.
However I can reproduce the problem in mainline if I force
__perf_pmu__new_alias() to be inlined.
Suppress this by using scnprintf() as has been done elsewhere in perf.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20181111184524.fux4taownc6ndbx6@decadent.org.uk
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The tool perf is useful for the performance analysis on the Hygon Dhyana
platform. But right now there is no Hygon support for it to analyze the
KVM guest os data. So add Hygon Dhyana support to it by checking vendor
string to share the code path of AMD.
Signed-off-by: Pu Wen <puwen@hygon.cn>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1542008451-31735-1-git-send-email-puwen@hygon.cn
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This program benchmarks concurrent epoll_wait(2) for file descriptors
that are monitored with with EPOLLIN along various semantics, by a
single epoll instance. Such conditions can be found when using
single/combined or multiple queuing when load balancing.
Each thread has a number of private, nonblocking file descriptors,
referred to as fdmap. A writer thread will constantly be writing to the
fdmaps of all threads, minimizing each threads's chances of epoll_wait
not finding any ready read events and blocking as this is not what we
want to stress. Full details in the start of the C file.
Committer testing:
# perf bench
Usage:
perf bench [<common options>] <collection> <benchmark> [<options>]
# List of all available benchmark collections:
sched: Scheduler and IPC benchmarks
mem: Memory access benchmarks
numa: NUMA scheduling and MM benchmarks
futex: Futex stressing benchmarks
epoll: Epoll stressing benchmarks
all: All benchmarks
# perf bench epoll
# List of available benchmarks for collection 'epoll':
wait: Benchmark epoll concurrent epoll_waits
all: Run all futex benchmarks
# perf bench epoll wait
# Running 'epoll/wait' benchmark:
Run summary [PID 19295]: 3 threads monitoring on 64 file-descriptors for 8 secs.
[thread 0] fdmap: 0xdaa650 ... 0xdaa74c [ 328241 ops/sec ]
[thread 1] fdmap: 0xdaa900 ... 0xdaa9fc [ 351695 ops/sec ]
[thread 2] fdmap: 0xdaabb0 ... 0xdaacac [ 381423 ops/sec ]
Averaged 353786 operations/sec (+- 4.35%), total secs = 8
#
Committer notes:
Fix the build on debian:experimental-x-mips, debian:experimental-x-mipsel
and others:
CC /tmp/build/perf/bench/epoll-wait.o
bench/epoll-wait.c: In function 'writerfn':
bench/epoll-wait.c:399:12: error: format '%ld' expects argument of type 'long int', but argument 2 has type 'size_t' {aka 'unsigned int'} [-Werror=format=]
printinfo("exiting writer-thread (total full-loops: %ld)\n", iter);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ~~~~
bench/epoll-wait.c:86:31: note: in definition of macro 'printinfo'
do { if (__verbose) { printf(fmt, ## arg); fflush(stdout); } } while (0)
^~~
cc1: all warnings being treated as errors
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Jason Baron <jbaron@akamai.com> <jbaron@akamai.com>
Link: http://lkml.kernel.org/r/20181106152226.20883-2-dave@stgolabs.net
Link: http://lkml.kernel.org/r/20181106182349.thdkpvshkna5vd7o@linux-r8p5>
[ Applied above fixup as per Davidlohr's request ]
[ Use inttypes.h to print rlim_t fields, fixing the build on Alpine Linux / musl libc ]
[ Check if eventfd() is available, i.e. if HAVE_EVENTFD is defined ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
A new 'perf bench epoll' will use this, and to disable it for older
systems, add a feature test for this API.
This is just a simple program that if successfully compiled, means that
the feature is present, at least at the library level, in a build that
sets the output directory to /tmp/build/perf (using O=/tmp/build/perf),
we end up with:
$ ls -la /tmp/build/perf/feature/test-eventfd*
-rwxrwxr-x. 1 acme acme 8176 Nov 21 15:58 /tmp/build/perf/feature/test-eventfd.bin
-rw-rw-r--. 1 acme acme 588 Nov 21 15:58 /tmp/build/perf/feature/test-eventfd.d
-rw-rw-r--. 1 acme acme 0 Nov 21 15:58 /tmp/build/perf/feature/test-eventfd.make.output
$ ldd /tmp/build/perf/feature/test-eventfd.bin
linux-vdso.so.1 (0x00007fff3bf3f000)
libc.so.6 => /lib64/libc.so.6 (0x00007fa984061000)
/lib64/ld-linux-x86-64.so.2 (0x00007fa984417000)
$ grep eventfd -A 2 -B 2 /tmp/build/perf/FEATURE-DUMP
feature-dwarf=1
feature-dwarf_getlocations=1
feature-eventfd=1
feature-fortify-source=1
feature-sync-compare-and-swap=1
$
The main thing here is that in the end we'll have -DHAVE_EVENTFD in
CFLAGS, and then the 'perf bench' entry needing that API can be
selectively pruned.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/n/tip-wkeldwob7dpx6jvtuzl8164k@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Ido Schimmel says:
====================
mlxsw: Add VxLAN learning support
This patchset adds VxLAN learning support in the mlxsw driver.
The first five patches from Petr add the required switchdev APIs which
allow device drivers to notify the VxLAN driver about learned / aged-out
FDB entries.
First in patch #1, an unnecessary argument is dropped from
__vxlan_fdb_delete().
In patches #2-#4, the VxLAN FDB handling code is extended to make
sending the switchdev events configurable; to mark user-added entries as
such; and to make sure HW-learned FDB entries do not take over
user-added ones.
Finally in patch #5, the necessary switchdev notifications are added and
handled by VxLAN, similarly to how this is handled in the bridge driver.
Patch #6 allows changing of the VxLAN's device ageing time since it is
useful for the selftest in the last patch.
Patch #7 adds support for querying bridge port flags of a given
netdevice, as a new entry should not be learned and notified to the
bridge driver in case learning is disabled on the bridge port.
Next patches gradually add learning support in mlxsw.
The last patch adds a new test case for VxLAN learning.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test which checks that the VxLAN driver can learn FDB entries and
that these entries are correctly deleted and aged-out.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test currently expects that a configuration which includes a VxLAN
device with learning enabled to fail.
Previous patches enabled VxLAN learning in mlxsw, so change the test
accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the driver returned an error when learning was enabled on a
VxLAN device enslaved to an offloaded bridge.
Previous patches added VxLAN learning support, so remove the check.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow users to delete learned FDB entries from the bridge's FDB before
enabling VxLAN learning.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Start processing two new entry types in addition to current ones:
* Learned unicast tunnel entry
* Aged-out unicast tunnel entry
In both cases the device reports on a new {MAC, FID, IP address} tuple
that was learned / aged-out. Based on this notification, the driver
instructs the device to add / delete the entry to / from its database.
The driver also makes sure to notify the bridge and VxLAN drivers about
the new entry.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDB notifications for entries learned from an NVE tunnel contain the IP
address of the remote VTEP. In the case of IPv4 underlay, the IP address
is specified as-is. IPv6 addresses on the other hand, are specified as
handles which then need to be used to query the actual address from the
device.
Only IPv4 underlay is currently supported, so we cannot receive
notifications for IPv6 addresses and therefore an error is returned when
one tries to resolve such an address.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing a notification about a new FDB entry learned from a
VxLAN tunnel, the driver is provided with the FID index among other
parameters.
The driver potentially needs to update the bridge and VxLAN drivers
about the new entry using a pointer to the VxLAN device and the
corresponding VNI.
These two parameters are stored in the FID, so add a new function that
allows looking up a FID based on its index.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver periodically polls for new FDB entries learned by the device.
In the case of an FDB entry learned from a VxLAN tunnel, the
notification includes the IP of the remote VTEP, the filtering
identifier (FID) and the source MAC address of the overlay packet.
Assuming learning is enabled in the VxLAN and bridge drivers, the driver
needs to generate a notification and update them about the new FDB
entry.
Store the ifindex of the NVE device in the FID so that the driver will
be able to update the VxLAN and bridge drivers using it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will be used to process learned FDB records from an NVE tunnel.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
