Allow querying bridge port flags so that drivers capable of performing
VxLAN learning will update the bridge driver only if learning is enabled
on its bridge port corresponding to the VxLAN device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to the bridge device, allow changing the ageing
time of the VxLAN device by scheduling its timer to fire if the ageing
time changed.
One use case is selftests where learning / ageing of VxLAN FDB entries
is tested. The default ageing time is 5 minutes, which is too long for a
simple selftest.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow devices to signal learning events to VXLAN, introduce
two new switchdev messages: SWITCHDEV_VXLAN_FDB_ADD_TO_BRIDGE and
SWITCHDEV_VXLAN_FDB_DEL_TO_BRIDGE.
Listen to these notifications in the vxlan driver. The FDB entries
learned this way have an NTF_EXT_LEARNED flag, and only entries marked
as such can be unlearned by the _DEL_ event. They are also immediately
marked as offloaded. This is the same behavior that the bridge driver
observes.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an external learning event collides with an user-added entry, the
user-added entry shouldn't be taken over. Otherwise on an unlearn event
the entry would be completely lost, even though the user added it by
hand.
Therefore skip update of FDB flags and state for these cases. This is in
accordance with the bridge behavior.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VXLAN driver needs to differentiate between FDB entries learned by
the VXLAN driver, and those added by the user. The latter ones shouldn't
be taken over by external learning events. This is in accordance with
bridge behavior.
Therefore, extend the flags bitfield to 16 bits and add a new private
NTF flag to mark the user-added entries.
This seems preferable to adding a dedicated boolean, because passing the
flag, unlike passing e.g. a true, makes it clear what the meaning of the
bit is.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a following patch, vxlan is extended to allow hardware FDB learning.
For FDB entries learned this way, switchdev notifications should not be
sent again, because the driver already knows about these entries.
To that end, add an argument vxlan_fdb_notify() to determine whether
the switchdev notifications should be sent. Propagate the argument to
all call sites transitively, eventually passing true in all root calls.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This argument is necessary for vxlan_fdb_delete(), the API of which is
prescribed by ndo_fdb_del, but __vxlan_fdb_delete() doesn't need it.
Therefore drop it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original ftmac100_interrupt(), the interrupts are only disabled when
the condition "netif_running(netdev)" is true. However, this condition
causes kerenl hang in the following case. When the user requests to
disable the network device, kernel will clear the bit __LINK_STATE_START
from the dev->state and then call the driver's ndo_stop function. Network
device interrupts are not blocked during this process. If an interrupt
occurs between clearing __LINK_STATE_START and stopping network device,
kernel cannot disable the interrupts due to the condition
"netif_running(netdev)" in the ISR. Hence, kernel will hang due to the
continuous interruption of the network device.
In order to solve the above problem, the interrupts of the network device
should always be disabled in the ISR without being restricted by the
condition "netif_running(netdev)".
[V2]
Remove unnecessary curly braces.
Signed-off-by: Vincent Chen <vincentc@andestech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of pitches is not correct while calling mode_set.
The issue we found so far on following system:
- Debian8 with XFCE Desktop
- Ubuntu with KDE Desktop
- SUSE15 with KDE Desktop
Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com>
Cc: <stable@vger.kernel.org>
Tested-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Ursula Braun says:
====================
net/smc: fixes 2018-11-12
here is V4 of some net/smc fixes in different areas for the net tree.
v1->v2:
do not define 8-byte alignment for union smcd_cdc_cursor in
patch 4/5 "net/smc: atomic SMCD cursor handling"
v2->v3:
stay with 8-byte alignment for union smcd_cdc_cursor in
patch 4/5 "net/smc: atomic SMCD cursor handling", but get rid of
__packed for struct smcd_cdc_msg
v3->v4:
get rid of another __packed for struct smc_cdc_msg in
patch 4/5 "net/smc: atomic SMCD cursor handling"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In smc_wr_tx_put_slot() field pend->idx is used after being
cleared. That means always idx 0 is cleared in the wr_tx_mask.
This results in a broken administration of available WR send
payload buffers.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running uperf tests with SMCD on LPARs results in corrupted cursors.
SMCD cursors should be treated atomically to fix cursor corruption.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a SMC-D link group is freed, a shutdown signal should be sent to
the peer to indicate that the link group is invalid. This patch adds the
shutdown signal to the SMC code.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When searching for an existing link group the queue pair number is also
to be taken into consideration. When the SMC server sends a new number
in a CLC packet (keeping all other values equal) then a new link group
is to be created on the SMC client side.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of a non-blocking SMC socket, the initial CLC handshake is
performed over a blocking TCP connection in a worker. If the SMC socket
is released, smc_release has to wait for the blocking CLC socket
operations (e.g., kernel_connect) inside the worker.
This patch aborts a CLC connection when the respective non-blocking SMC
socket is released to avoid waiting on socket operations or timeouts.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of fixes for 4.20, this time we have quite a few them but
all very small.
ath9k
* fix a locking regression found by a static checker
wlcore
* fix a crash which was a regression with wakeirq handling
brcm80211
* yet another fix for 160 MHz channel handling
mt76
* fix a longstaning build problem when CONFIG_LEDS_CLASS is disabled
* don't use uninitialised mutex
iwlwifi
* do note that the iwlwifi merge tag (commit 4ec321c146) seems to
contain wrong list of changes so ignore that
* fix ACPI data handling, a memory leak and other smaller fixes
ath10k
* fix a crash during suspend which was a recent regression
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJb9CR9AAoJEG4XJFUm622bMdAH/2z0jY38RTPqLYH7BKfIzQkB
M8GC4bi0c3NexkwS+S0xLr6A5FyTcbi2pKOqdZ2eXEoiopso5OocWXYnIw0IDA9C
ll5aI4DfIoqTIVBvYWp/Rnar67oRAfND5z3iOnu0C34KNiMbUY2WfJ6RUTo+gjZ4
Wokaf6EWOCODDtL2atBtvT96JSlM7t398aUksKzcOGX+0XPGYfyho/wQGZIYE9iQ
Exgmp9KyBBlQugu+EyGH+Dxt8J+1sSveIJXnfaCb9avtpo+C/SG7+pnJhX8ij7fH
+pYuWOq/YyliUVHVxfpK5+lVJB3ICGezbZ6xp3G3MURBqdX/E2oouFJvyKrESPc=
=je2r
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-11-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.20
First set of fixes for 4.20, this time we have quite a few them but
all very small.
ath9k
* fix a locking regression found by a static checker
wlcore
* fix a crash which was a regression with wakeirq handling
brcm80211
* yet another fix for 160 MHz channel handling
mt76
* fix a longstaning build problem when CONFIG_LEDS_CLASS is disabled
* don't use uninitialised mutex
iwlwifi
* do note that the iwlwifi merge tag (commit 4ec321c146) seems to
contain wrong list of changes so ignore that
* fix ACPI data handling, a memory leak and other smaller fixes
ath10k
* fix a crash during suspend which was a recent regression
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jean-Louis reported a TCP regression and bisected to recent SACK
compression.
After a loss episode (receiver not able to keep up and dropping
packets because its backlog is full), linux TCP stack is sending
a single SACK (DUPACK).
Sender waits a full RTO timer before recovering losses.
While RFC 6675 says in section 5, "Algorithm Details",
(2) If DupAcks < DupThresh but IsLost (HighACK + 1) returns true --
indicating at least three segments have arrived above the current
cumulative acknowledgment point, which is taken to indicate loss
-- go to step (4).
...
(4) Invoke fast retransmit and enter loss recovery as follows:
there are old TCP stacks not implementing this strategy, and
still counting the dupacks before starting fast retransmit.
While these stacks probably perform poorly when receivers implement
LRO/GRO, we should be a little more gentle to them.
This patch makes sure we do not enable SACK compression unless
3 dupacks have been sent since last rcv_nxt update.
Ideally we should even rearm the timer to send one or two
more DUPACK if no more packets are coming, but that will
be work aiming for linux-4.21.
Many thanks to Jean-Louis for bisecting the issue, providing
packet captures and testing this patch.
Fixes: 5d9f4262b7 ("tcp: add SACK compression")
Reported-by: Jean-Louis Dupond <jean-louis@dupond.be>
Tested-by: Jean-Louis Dupond <jean-louis@dupond.be>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a possible null pointer dereference in
do_load, detected by the semantic patch deref_null.cocci,
with the following warning:
./tools/bpf/bpftool/prog.c:1021:23-25: ERROR: map_replace is NULL but dereferenced.
The following code has potential null pointer references:
881 map_replace = reallocarray(map_replace, old_map_fds + 1,
882 sizeof(*map_replace));
883 if (!map_replace) {
884 p_err("mem alloc failed");
885 goto err_free_reuse_maps;
886 }
...
1019 err_free_reuse_maps:
1020 for (i = 0; i < old_map_fds; i++)
1021 close(map_replace[i].fd);
1022 free(map_replace);
Fixes: 3ff5a4dc5d ("tools: bpftool: allow reuse of maps with bpftool prog load")
Co-developed-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Michał Mirosław says:
====================
VLAN tag handling cleanup
This is a cleanup set after VLAN_TAG_PRESENT removal. The CFI bit
handling is made similar to how other tag fields are used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace open-coded bitfield manipulation with skb_vlan_tag_*() helpers.
This also enables correctly passing of VLAN.CFI bit.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abstract CFI/DEI bit access consistently with other VLAN tag fields.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet is trapped and the corresponding SKB marked as
already-forwarded, it retains this marking even after it is forwarded
across veth links into another bridge. There, since it ingresses the
bridge over veth, which doesn't have offload_fwd_mark, it triggers a
warning in nbp_switchdev_frame_mark().
Then nbp_switchdev_allowed_egress() decides not to allow egress from
this bridge through another veth, because the SKB is already marked, and
the mark (of 0) of course matches. Thus the packet is incorrectly
blocked.
Solve by resetting offload_fwd_mark() in skb_scrub_packet(). That
function is called from tunnels and also from veth, and thus catches the
cases where traffic is forwarded between bridges and transformed in a
way that invalidates the marking.
Fixes: 6bc506b4fb ("bridge: switchdev: Add forward mark support for stacked devices")
Fixes: abf4bb6b63 ("skbuff: Add the offload_mr_fwd_mark field")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Suggested-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Select CONFIG_HAVE_LD_DEAD_CODE_DATA_ELIMINATION for MIPS, allowing the
user to enable dead code elimination. In order for this to work, ensure
that we keep the data bus exception table & the machine list by
annotating them with KEEP.
This shrinks both 32r2el_defconfig & 64r6el_defconfig builds by ~6%, as
shown by numbers from scripts/bloat-o-meter:
| 32r2el_defconfig | 64r6el_defconfig
--------|------------------|------------------
No DCE | 8919864 | 8286307
DCE | 8338988 (-6.51%) | 7741808 (-6.57%)
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21187/
Cc: linux-mips@linux-mips.org
If we are about to return the same register address that would
be the default anyway, fallback to default return instead of adding
a case label.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21200/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
When register definition is identical on all OCTEONs, we can trivially
delete the model specific union fields.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21203/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Delete cmvx override functions, they are not used.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21196/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Make cvmx_bootmem_alloc_range() static, it's not used outside the file.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21195/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Make cvmx_helper_setup_red_queue static, it's not used outside this file.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21194/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Include linux/sched/clock.h to get the declaration for sched_clock().
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21189/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Use correct type for fdt_property nameoff field.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21204/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Make __cvmx_helper_errata_fix_ipd_ptr_alignment static, it's not used
outside the file.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21210/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Include arm/prom.h to get the declaration of device_tree_init().
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21202/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Include asm/fw/fw.h to get the declaration of fw_init_cmdline().
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21206/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Make some internal data and functions static to avoid sparse warnings.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21211/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Make cvmx_l2c_spinlock static, it's not used outside the file.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/21209/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
