When there exist a pair of raw sockets one unbound and one bound
to a VRF but equal in all other respects, when a packet is received
in the VRF context, __raw_v4_lookup() matches on both sockets.
This results in the packet being delivered over both sockets,
instead of only the raw socket bound to the VRF. The bound device
checks in __raw_v4_lookup() are replaced with a call to
raw_sk_bound_dev_eq() which correctly handles whether the packet
should be delivered over the unbound socket in such cases.
In __raw_v6_lookup() the match on the device binding of the socket is
similarly updated to use raw_sk_bound_dev_eq() which matches the
handling in __raw_v4_lookup().
Importantly raw_sk_bound_dev_eq() takes the raw_l3mdev_accept sysctl
into account.
Signed-off-by: Duncan Eastoe <deastoe@vyatta.att-mail.com>
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a sysctl raw_l3mdev_accept to control raw socket lookup in a manner
similar to use of tcp_l3mdev_accept for stream and of udp_l3mdev_accept
for datagram sockets. Have this default to enabled for reasons of
backwards compatibility. This is so as to specify the output device
with cmsg and IP_PKTINFO, but using a socket not bound to the
corresponding VRF. This allows e.g. older ping implementations to be
run with specifying the device but without executing it in the VRF.
If the option is disabled, packets received in a VRF context are only
handled by a raw socket bound to the VRF, and correspondingly packets
in the default VRF are only handled by a socket not bound to any VRF.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure an unbound datagram skt is chosen when not in a VRF. The check
for a device match in compute_score() for UDP must be performed when
there is no device match. For this, a failure is returned when there is
no device match. This ensures that bound sockets are never selected,
even if there is no unbound socket.
Allow IPv6 packets to be sent over a datagram skt bound to a VRF. These
packets are currently blocked, as flowi6_oif was set to that of the
master vrf device, and the ipi6_ifindex is that of the slave device.
Allow these packets to be sent by checking the device with ipi6_ifindex
has the same L3 scope as that of the bound device of the skt, which is
the master vrf device. Note that this check always succeeds if the skt
is unbound.
Even though the right datagram skt is now selected by compute_score(),
a different skt is being returned that is bound to the wrong vrf. The
difference between these and stream sockets is the handling of the skt
option for SO_REUSEPORT. While the handling when adding a skt for reuse
correctly checks that the bound device of the skt is a match, the skts
in the hashslot are already incorrect. So for the same hash, a skt for
the wrong vrf may be selected for the required port. The root cause is
that the skt is immediately placed into a slot when it is created,
but when the skt is then bound using SO_BINDTODEVICE, it remains in the
same slot. The solution is to move the skt to the correct slot by
forcing a rehash.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit a04a480d43 ("net: Require exact match for TCP socket
lookups if dif is l3mdev") only ensures that the correct socket is
selected for packets in a VRF. However, there is no guarantee that
the unbound socket will be selected for packets when not in a VRF.
By checking for a device match in compute_score() also for the case
when there is no bound device and attaching a score to this, the
unbound socket is selected. And if a failure is returned when there
is no device match, this ensures that bound sockets are never selected,
even if there is no unbound socket.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the inet socket lookup to avoid packets arriving on a device
enslaved to an l3mdev from matching unbound sockets by removing the
wildcard for non sk_bound_dev_if and instead relying on check against
the secondary device index, which will be 0 when the input device is
not enslaved to an l3mdev and so match against an unbound socket and
not match when the input device is enslaved.
Change the socket binding to take the l3mdev into account to allow an
unbound socket to not conflict sockets bound to an l3mdev given the
datapath isolation now guaranteed.
Signed-off-by: Robert Shearman <rshearma@vyatta.att-mail.com>
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[why]
Removing connector reusage from DM to match the rest of the tree ended
up revealing an issue that was surprisingly subtle. The original amdgpu
code for DC that was submitted appears to have left a chunk in
dm_dp_create_fake_mst_encoder() that tries to find a "master encoder",
the likes of which isn't actually used or stored anywhere. It does so at
the wrong time as well by trying to access parts of the drm_connector
from the encoder init before it's actually been initialized. This
results in a NULL pointer deref on MST hotplugs:
[ 160.696613] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[ 160.697234] PGD 0 P4D 0
[ 160.697814] Oops: 0010 [#1] SMP PTI
[ 160.698430] CPU: 2 PID: 64 Comm: kworker/2:1 Kdump: loaded Tainted: G O 4.19.0Lyude-Test+ #2
[ 160.699020] Hardware name: HP HP ZBook 15 G4/8275, BIOS P70 Ver. 01.22 05/17/2018
[ 160.699672] Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
[ 160.700322] RIP: 0010: (null)
[ 160.700920] Code: Bad RIP value.
[ 160.701541] RSP: 0018:ffffc9000029fc78 EFLAGS: 00010206
[ 160.702183] RAX: 0000000000000000 RBX: ffff8804440ed468 RCX: ffff8804440e9158
[ 160.702778] RDX: 0000000000000000 RSI: ffff8804556c5700 RDI: ffff8804440ed000
[ 160.703408] RBP: ffff880458e21800 R08: 0000000000000002 R09: 000000005fca0a25
[ 160.704002] R10: ffff88045a077a3d R11: ffff88045a077a3c R12: ffff8804440ed000
[ 160.704614] R13: ffff880458e21800 R14: ffff8804440e9000 R15: ffff8804440e9000
[ 160.705260] FS: 0000000000000000(0000) GS:ffff88045f280000(0000) knlGS:0000000000000000
[ 160.705854] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 160.706478] CR2: ffffffffffffffd6 CR3: 000000000200a001 CR4: 00000000003606e0
[ 160.707124] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 160.707724] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 160.708372] Call Trace:
[ 160.708998] ? dm_dp_add_mst_connector+0xed/0x1d0 [amdgpu]
[ 160.709625] ? drm_dp_add_port+0x2fa/0x470 [drm_kms_helper]
[ 160.710284] ? wake_up_q+0x54/0x70
[ 160.710877] ? __mutex_unlock_slowpath.isra.18+0xb3/0x110
[ 160.711512] ? drm_dp_dpcd_access+0xe7/0x110 [drm_kms_helper]
[ 160.712161] ? drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper]
[ 160.712762] ? drm_dp_check_and_send_link_address+0xa3/0xd0 [drm_kms_helper]
[ 160.713408] ? drm_dp_mst_link_probe_work+0x4b/0x80 [drm_kms_helper]
[ 160.714013] ? process_one_work+0x1a1/0x3a0
[ 160.714667] ? worker_thread+0x30/0x380
[ 160.715326] ? wq_update_unbound_numa+0x10/0x10
[ 160.715939] ? kthread+0x112/0x130
[ 160.716591] ? kthread_create_worker_on_cpu+0x70/0x70
[ 160.717262] ? ret_from_fork+0x35/0x40
[ 160.717886] Modules linked in: amdgpu(O) vfat fat snd_hda_codec_generic joydev i915 chash gpu_sched ttm i2c_algo_bit drm_kms_helper snd_hda_codec_hdmi hp_wmi syscopyarea iTCO_wdt sysfillrect sparse_keymap sysimgblt fb_sys_fops snd_hda_intel usbhid wmi_bmof drm snd_hda_codec btusb snd_hda_core intel_rapl btrtl x86_pkg_temp_thermal btbcm btintel coretemp snd_pcm crc32_pclmul bluetooth psmouse snd_timer snd pcspkr i2c_i801 mei_me i2c_core soundcore mei tpm_tis wmi tpm_tis_core hp_accel ecdh_generic lis3lv02d tpm video rfkill acpi_pad input_polldev hp_wireless pcc_cpufreq crc32c_intel serio_raw tg3 xhci_pci xhci_hcd [last unloaded: amdgpu]
[ 160.720141] CR2: 0000000000000000
Somehow the connector reusage DM was using for MST connectors managed to
paper over this issue entirely; hence why this was never caught until
now.
[how]
Since this code isn't used anywhere and seems useless anyway, we can
just drop it entirely. This appears to fix the issue on my HP ZBook with
an AMD WX4150.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It is not safe to keep existing connector while entire topology
has been removed. Could lead potential impact to uapi.
Entirely unregister all the connectors on the topology,
and use a new set of connectors when the topology is plugged back
on.
[How]
Remove the drm connector entirely each time when the
corresponding MST topology is gone.
When hotunplug a connector (e.g., DP2)
1. Remove connector from userspace.
2. Drop it's reference.
When hotplug back on:
1. Detect new topology, and create new connectors.
2. Notify userspace with sysfs hotplug event.
3. Reprobe new connectors, and reassign CRTC from old (e.g., DP2)
to new (e.g., DP3) connector.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It is not correct to touch aconnector within atomic_check.
[How]
It was added as workaround before, and no longer needed.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With UCLK DPM enabled, slow switching is not supported any more.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise big gap between these two clocks may causes
some hangs.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Trivial fixes to spelling mistakes in ftrace.rst
v2: tripple -> triple
Signed-off-by: Amir Livneh <alivneh@fb.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This is a small cleanup to kselftest.rst:
- Fix some language typos in the usage instructions.
- Change one non-ASCII space to an ASCII space.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
If the kernel allocates a bounce buffer for user read data, this memory
needs to be cleared before copying it to the user, otherwise it may leak
kernel memory to user space.
Laurence Oberman <loberman@redhat.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, function parameter description can match '@type.member'
expressions but fails to match '@type->member'.
Extend the $type_param regex to allow matching both
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
In the Function documentation Section of kernel-doc.rst
there is a function_name() function as an example for
how to make a comment about a function.
But at the end of that example there is a reference to foobar
instead of function_name.
I think that should rather be function_name, because that
was the placeholder the whole example was using.
Signed-off-by: Joris Gutjahr <joris.gutjahr@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Trivial fix to a spelling mistake of the error access name EACCESS,
rename to EACCES
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
It was found that two of the fields in the /proc/<pid>/status file were
missing - CapAmb & Speculation_Store_Bypass. They are now added to the
proc.txt documentation file.
v2: Update the example as well.
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
libata.git no longer exists. Replace the remaining pointers to it by
pointers to the block tree, which is where all libata development
happens now.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix grammar about wildcards and insert a space between sentences.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Cc: Will Korteland <will@korte.land>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fix a few "typos" in dynamic-debug-howto.rst.
s/dyndbg_query/ddebug_query/
s/sysfs/debugfs/
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
In copy_result_to_user(), we first create a struct dlm_lock_result, which
contains a struct dlm_lksb, the last member of which is a pointer to the
lvb. Unfortunately, we copy the entire struct dlm_lksb to the result
struct, which is then copied to userspace at the end of the function,
leaking the contents of sb_lvbptr, which is a valid kernel pointer in some
cases (indeed, later in the same function the data it points to is copied
to userspace).
It is an error to leak kernel pointers to userspace, as it undermines KASLR
protections (see e.g. 65eea8edc3 ("floppy: Do not copy a kernel pointer to
user memory in FDGETPRM ioctl") for another example of this).
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: David Teigland <teigland@redhat.com>
kobject doesn't like zero length object names, so let's test for that.
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: David Teigland <teigland@redhat.com>
Causes a black screen on a Stoney laptop.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=108577
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set the dc_config properly when the option is enabled.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add FBC to the list of features that can be enabled from the DM.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Similar to ppfeaturemask. Allows you to selectively enable/disable
DC features.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The value is dependent on whether fbc is available.
v2: only check if num_pipes is valid
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, SDMA page queue is not used under SR-IOV VF, and this queue will
cause ring test failure in amdgpu module reload case. So just disable it.
Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For Vega20, LBPW feature is disabled at default.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With UCLK DPM enabled, slow switching is not supported any more.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise big gap between these two clocks may causes
some hangs.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Removing connector reusage from DM to match the rest of the tree ended
up revealing an issue that was surprisingly subtle. The original amdgpu
code for DC that was submitted appears to have left a chunk in
dm_dp_create_fake_mst_encoder() that tries to find a "master encoder",
the likes of which isn't actually used or stored anywhere. It does so at
the wrong time as well by trying to access parts of the drm_connector
from the encoder init before it's actually been initialized. This
results in a NULL pointer deref on MST hotplugs:
[ 160.696613] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[ 160.697234] PGD 0 P4D 0
[ 160.697814] Oops: 0010 [#1] SMP PTI
[ 160.698430] CPU: 2 PID: 64 Comm: kworker/2:1 Kdump: loaded Tainted: G O 4.19.0Lyude-Test+ #2
[ 160.699020] Hardware name: HP HP ZBook 15 G4/8275, BIOS P70 Ver. 01.22 05/17/2018
[ 160.699672] Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
[ 160.700322] RIP: 0010: (null)
[ 160.700920] Code: Bad RIP value.
[ 160.701541] RSP: 0018:ffffc9000029fc78 EFLAGS: 00010206
[ 160.702183] RAX: 0000000000000000 RBX: ffff8804440ed468 RCX: ffff8804440e9158
[ 160.702778] RDX: 0000000000000000 RSI: ffff8804556c5700 RDI: ffff8804440ed000
[ 160.703408] RBP: ffff880458e21800 R08: 0000000000000002 R09: 000000005fca0a25
[ 160.704002] R10: ffff88045a077a3d R11: ffff88045a077a3c R12: ffff8804440ed000
[ 160.704614] R13: ffff880458e21800 R14: ffff8804440e9000 R15: ffff8804440e9000
[ 160.705260] FS: 0000000000000000(0000) GS:ffff88045f280000(0000) knlGS:0000000000000000
[ 160.705854] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 160.706478] CR2: ffffffffffffffd6 CR3: 000000000200a001 CR4: 00000000003606e0
[ 160.707124] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 160.707724] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 160.708372] Call Trace:
[ 160.708998] ? dm_dp_add_mst_connector+0xed/0x1d0 [amdgpu]
[ 160.709625] ? drm_dp_add_port+0x2fa/0x470 [drm_kms_helper]
[ 160.710284] ? wake_up_q+0x54/0x70
[ 160.710877] ? __mutex_unlock_slowpath.isra.18+0xb3/0x110
[ 160.711512] ? drm_dp_dpcd_access+0xe7/0x110 [drm_kms_helper]
[ 160.712161] ? drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper]
[ 160.712762] ? drm_dp_check_and_send_link_address+0xa3/0xd0 [drm_kms_helper]
[ 160.713408] ? drm_dp_mst_link_probe_work+0x4b/0x80 [drm_kms_helper]
[ 160.714013] ? process_one_work+0x1a1/0x3a0
[ 160.714667] ? worker_thread+0x30/0x380
[ 160.715326] ? wq_update_unbound_numa+0x10/0x10
[ 160.715939] ? kthread+0x112/0x130
[ 160.716591] ? kthread_create_worker_on_cpu+0x70/0x70
[ 160.717262] ? ret_from_fork+0x35/0x40
[ 160.717886] Modules linked in: amdgpu(O) vfat fat snd_hda_codec_generic joydev i915 chash gpu_sched ttm i2c_algo_bit drm_kms_helper snd_hda_codec_hdmi hp_wmi syscopyarea iTCO_wdt sysfillrect sparse_keymap sysimgblt fb_sys_fops snd_hda_intel usbhid wmi_bmof drm snd_hda_codec btusb snd_hda_core intel_rapl btrtl x86_pkg_temp_thermal btbcm btintel coretemp snd_pcm crc32_pclmul bluetooth psmouse snd_timer snd pcspkr i2c_i801 mei_me i2c_core soundcore mei tpm_tis wmi tpm_tis_core hp_accel ecdh_generic lis3lv02d tpm video rfkill acpi_pad input_polldev hp_wireless pcc_cpufreq crc32c_intel serio_raw tg3 xhci_pci xhci_hcd [last unloaded: amdgpu]
[ 160.720141] CR2: 0000000000000000
Somehow the connector reusage DM was using for MST connectors managed to
paper over this issue entirely; hence why this was never caught until
now.
[how]
Since this code isn't used anywhere and seems useless anyway, we can
just drop it entirely. This appears to fix the issue on my HP ZBook with
an AMD WX4150.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It is not safe to keep existing connector while entire topology
has been removed. Could lead potential impact to uapi.
Entirely unregister all the connectors on the topology,
and use a new set of connectors when the topology is plugged back
on.
[How]
Remove the drm connector entirely each time when the
corresponding MST topology is gone.
When hotunplug a connector (e.g., DP2)
1. Remove connector from userspace.
2. Drop it's reference.
When hotplug back on:
1. Detect new topology, and create new connectors.
2. Notify userspace with sysfs hotplug event.
3. Reprobe new connectors, and reassign CRTC from old (e.g., DP2)
to new (e.g., DP3) connector.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It is not correct to touch aconnector within atomic_check.
[How]
It was added as workaround before, and no longer needed.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of stack-allocated psp_xgmi_topology_info in function
amdgpu_xgmi_add_device, dynamically allocated this structure to
avoid the frame size of this function excceed 1024 bytes
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It was previously noted that Kconfig complained about unmet dependencies
when trying to configure skx_edac together with CONFIG_ACPI=n. First fix
for this checked for ACPI when doing
select ACPI_ADXL
but this required stub functions for the case where ACPI wasn't
selected. It also allowed building a driver that didn't actually work
for a system that has non-volatile DIMMs.
Arnd Bergmann pointed out that the right fix is to make EDAC_SKX
"depend on ACPI".
Fixes: a324e9396c ("EDAC, skx: Fix randconfig builds")
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Mauro Carvalho Chehab <mchehab@kernel.org>
CC: linux-edac <linux-edac@vger.kernel.org>
CC: qiuxu.zhuo@intel.com
Link: http://lkml.kernel.org/r/20181106183914.GA26731@agluck-desk
dlm_config_nodes() does not allocate nodes on failure, so we should not
free() nodes when it fails.
Signed-off-by: Tycho Andersen <tycho@tycho.ws>
Signed-off-by: David Teigland <teigland@redhat.com>
To help when debugging bpf/xdp load issues, have the load_map()
error message include the number and name of the map that
failed.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
We need to hold the device lock (and disable interrupts) while
writing new commands, or we could be interrupted while that
is happening and read invalid requests in the completion path.
Fixes: 4e6da0fe80 ("um: Convert ubd driver to blk-mq")
Tested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The limit for memory locked in the kernel by a process is usually set to
64 kbytes by default. This can be an issue when creating large BPF maps
and/or loading many programs. A workaround is to raise this limit for
the current process before trying to create a new BPF map. Changing the
hard limit requires the CAP_SYS_RESOURCE and can usually only be done by
root user (for non-root users, a call to setrlimit fails (and sets
errno) and the program simply goes on with its rlimit unchanged).
There is no API to get the current amount of memory locked for a user,
therefore we cannot raise the limit only when required. One solution,
used by bcc, is to try to create the map, and on getting a EPERM error,
raising the limit to infinity before giving another try. Another
approach, used in iproute2, is to raise the limit in all cases, before
trying to create the map.
Here we do the same as in iproute2: the rlimit is raised to infinity
before trying to load programs or to create maps with bpftool.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add a new cpufeature definition for the WBNOINVD instruction.
The WBNOINVD instruction writes all modified cache lines in all levels of
the cache associated with a processor to main memory while retaining the
cached values.
Both AMD and Intel support this instruction.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
CC: David Woodhouse <dwmw@amazon.co.uk>
CC: Fenghua Yu <fenghua.yu@intel.com>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Ingo Molnar <mingo@redhat.com>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Rudolf Marek <r.marek@assembler.cz>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/1541624211-32196-1-git-send-email-Janakarajan.Natarajan@amd.com
libbpf is now able to load successfully test_l4lb_noinline.o and
samples/bpf/tracex3_kern.o.
For the test_l4lb_noinline, uncomment related tests from test_libbpf.c
and remove the associated "TODO".
For tracex3_kern.o, instead of loading a program from samples/bpf/ that
might not have been compiled at this stage, try loading a program from
BPF selftests. Since this test case is about loading a program compiled
without the "-target bpf" flag, change the Makefile to compile one
program accordingly (instead of passing the flag for compiling all
programs).
Regarding test_xdp_noinline.o: in its current shape the program fails to
load because it provides no version section, but the loader needs one.
The test was added to make sure that libbpf could load XDP programs even
if they do not provide a version number in a dedicated section. But
libbpf is already capable of doing that: in our case loading fails
because the loader does not know that this is an XDP program (it does
not need to, since it does not attach the program). So trying to load
test_xdp_noinline.o does not bring much here: just delete this subtest.
For the record, the error message obtained with tracex3_kern.o was
fixed by commit e3d91b0ca5 ("tools/libbpf: handle issues with bpf ELF
objects containing .eh_frames")
I have not been abled to reproduce the "libbpf: incorrect bpf_call
opcode" error for test_l4lb_noinline.o, even with the version of libbpf
present at the time when test_libbpf.sh and test_libbpf_open.c were
created.
RFC -> v1:
- Compile test_xdp without the "-target bpf" flag, and try to load it
instead of ../../samples/bpf/tracex3_kern.o.
- Delete test_xdp_noinline.o subtest.
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add a description for dev and remove the excess one for native. Fixes
the following warnings:
../drivers/gpu/drm/drm_fourcc.c:112: warning: Function parameter or member 'dev' not described in 'drm_driver_legacy_fb_format'
../drivers/gpu/drm/drm_fourcc.c:112: warning: Excess function parameter 'native' description in 'drm_driver_legacy_fb_format'
Fixes: 059b5eb5d9 ("drm: move native byte order quirk to new drm_driver_legacy_fb_format function")
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107205546.216088-1-sean@poorly.run
Adds support for defining a variable number of poll queues, currently
configurable with the 'poll_queues' module parameter. Defaults to
a single poll queue.
And now we finally have poll support without triggering interrupts!
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We use IOCB_HIPRI to poll for IO in the caller instead of scheduling.
This information is not available for (or after) IO submission. The
driver may make different queue choices based on the type of IO, so
make the fact that we will poll for this IO known to the lower layers
as well.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
NVMe does round-robin between queues by default, which means that
sharing a queue map for both reads and writes can be problematic
in terms of read servicing. It's much easier to flood the queue
with writes and reduce the read servicing.
Implement two queue maps, one for reads and one for writes. The
write queue count is configurable through the 'write_queues'
parameter.
By default, we retain the previous behavior of having a single
queue set, shared between reads and writes. Setting 'write_queues'
to a non-zero value will create two queue sets, one for reads and
one for writes, the latter using the configurable number of
queues (hardware queue counts permitting).
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a queue offset to the tag map. This enables users to map
iteratively, for each queue map type they support.
Bump maximum number of supported maps to 2, we're now fully
able to support more than 1 map.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
