Add support for r8a7744. The Renesas RZ/G1N (R8A7744) PCIe controller
is identical to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This allows nonexclusive (simultaneous) access to a single
GPIO line for the fixed regulator enable line. This happens
when several regulators use the same GPIO for enabling and
disabling a regulator, and all need a handle on their GPIO
descriptor.
This solution with a special flag is not entirely elegant
and should ideally be replaced by something more careful as
this makes it possible for several consumers to
enable/disable the same GPIO line to the left and right
without any consistency. The current use inside the regulator
core should however be fine as it takes special care to
handle this.
For the state of the GPIO backend, this is still the
lesser evil compared to going back to global GPIO
numbers.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Fixes: efdfeb079c ("regulator: fixed: Convert to use GPIO descriptor only")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use PIO mode instead if size is smaller than fifo size, since
dma may be less efficient.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct wml as the last rx sg length instead of the whole transfer
length. Otherwise, mtd_stresstest will be failed as below:
insmod mtd_stresstest.ko dev=0
=================================================
mtd_stresstest: MTD device: 0
mtd_stresstest: not NAND flash, assume page size is 512 bytes.
mtd_stresstest: MTD device size 4194304, eraseblock size 65536, page size 512, count of eraseblocks 64, pa0
mtd_stresstest: doing operations
mtd_stresstest: 0 operations done
mtd_test: mtd_read from 1ff532, size 880
mtd_test: mtd_read from 20c267, size 64998
spi_master spi0: I/O Error in DMA RX
m25p80 spi0.0: SPI transfer failed: -110
spi_master spi0: failed to transfer one message from queue
mtd_test: error: read failed at 0x20c267
mtd_stresstest: error -110 occurred
=================================================
insmod: ERROR: could not insert module mtd_stresstest.ko: Connection timed out
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current dynamic burst length is based on the whole transfer length,
that's ok if there is only one sg, but is not right in case multi sgs
in one transfer,because the tail data should be based on the last sg
length instead of the whole transfer length. Move wml setting for DMA
to the later place, thus, the next patch could get the right last sg
length for wml setting. This patch is a preparation one, no any
function change involved.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
The Lochnagar board provides power supplies for the attached
CODEC/Amp device. Currently this driver supports the microphone
supplies and the digital core voltage for the attached
device. There are some additional supplies that will be
added in time but these supplies are sufficient for most
systems/use-cases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pcm3168a is supporting TDM on I2S/Left_J, but there is no
settings for it. This patch add it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LEFT_J / I2S only can use TDM.
This patch adds channel constraint for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RIGHT_J only can handle 16bit data bits.
Current driver just errored if user requests non RIGHT_J
+ 16bit combination. But it is not useful for user.
This patch adds HW constraint for it, and avoid
error on such situation.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Dan's smatch utility found an uninitialized use of offset in a path in
parse_probe_args(). Unless an offset is specifically specified for commands
that allow them, it should default to zero.
Link: http://lkml.kernel.org/r/20181012134246.5doqaobxunlqqs53@mwanda
Fixes: 533059281e ("tracing: probeevent: Introduce new argument fetching code")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> (smatch)
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This spares drivers from #ifdef-ing on CONFIG_PCI if the driver can be
optionally built on machines without PCI bus.
Consistent with acpi_driver_match_device() and similar.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix a stupid typo introduced in the refactoring.
Fixes: 0efe5523 ("fore200e: simplify fore200e_bus usage")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ESD watchdog code in sta32x_watchdog() dereferences the pointer
which is never assigned.
This is a regression from a1be4cead9 ("ASoC: sta32x: Convert to direct
regmap API usage.") which went unnoticed since nobody seems to use that ESD
workaround.
Fixes: a1be4cead9 ("ASoC: sta32x: Convert to direct regmap API usage.")
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When a link's carrier goes down it could be a sign of the port changing
networks. If the new network has overlapping addresses with the old one,
then the kernel will continue trying to use neighbor entries established
based on the old network until the entries finally age out - meaning a
potentially long delay with communications not working.
This patch evicts neighbor entries on carrier down with the exception of
those marked permanent. Permanent entries are managed by userspace (either
an admin or a routing daemon such as FRR).
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SPI configuration state includes an SPI_NO_CS flag that disables
all CS line manipulation, for applications that want to manage their
own chip selects. However, this flag is ignored by the GPIO CS code
in the SPI framework.
Correct this omission with a trivial patch.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Another difference between IPv4 and IPv6 is the generation of RTM_DELROUTE
notifications when a device is taken down (admin down) or deleted. IPv4
does not generate a message for routes evicted by the down or delete;
IPv6 does. A NOS at scale really needs to avoid these messages and have
IPv4 and IPv6 behave similarly, relying on userspace to handle link
notifications and evict the routes.
At this point existing user behavior needs to be preserved. Since
notifications are a global action (not per app) the only way to preserve
existing behavior and allow the messages to be skipped is to add a new
sysctl (net/ipv6/route/skip_notify_on_dev_down) which can be set to
disable the notificatioons.
IPv6 route code already supports the option to skip the message (it is
used for multipath routes for example). Besides the new sysctl we need
to pass the skip_notify setting through the generic fib6_clean and
fib6_walk functions to fib6_clean_node and to set skip_notify on calls
to __ip_del_rt for the addrconf_ifdown path.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/usb/cdc_ncm.c: In function 'cdc_ncm_status':
drivers/net/usb/cdc_ncm.c:1603:22: warning:
variable 'ctx' set but not used [-Wunused-but-set-variable]
struct cdc_ncm_ctx *ctx;
It not used any more after
commit fa83dbeee5 ("net: cdc_ncm: remove redundant "disconnected" flag")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two last minute bugfixes, both for NXP platforms:
* The Layerscape 'qbman' infrastructure suffers from probe ordering
bugs in some configurations, a two-patch series adds a hotfix for
this. 4.20 will have a longer set of patches to rework it.
* The old imx53-qsb board regressed in 4.19 after the addition
of cpufreq support, adding a set of explicit operating points
fixes this.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WY74
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Arnd writes:
"ARM: SoC fixes for 4.19
Two last minute bugfixes, both for NXP platforms:
* The Layerscape 'qbman' infrastructure suffers from probe ordering
bugs in some configurations, a two-patch series adds a hotfix for
this. 4.20 will have a longer set of patches to rework it.
* The old imx53-qsb board regressed in 4.19 after the addition
of cpufreq support, adding a set of explicit operating points
fixes this."
* tag 'armsoc-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
soc: fsl: qman_portals: defer probe after qman's probe
soc: fsl: qbman: add APIs to retrieve the probing status
ARM: dts: imx53-qsb: disable 1.2GHz OPP
The kbuild robot reports:
drivers/nvdimm/label.c:500:32: warning: restricted __le32 degrades to integer
...read 'nslot' into a local u32.
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds logic that is meant to make use of the namespace index data
to reduce the number of reads that are needed to initialize a given
namespace. The general idea is that once we have enough data to validate
the namespace index we do so and then proceed to fetch only those labels
that are not listed as being "free". By doing this I am seeing a total time
reduction from about 4-5 seconds to 2-3 seconds for 24 NVDIMM modules each
with 128K of label config area.
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch splits the initialization of the label data into two functions.
One for doing the init, and another for reading the actual configuration
data. The idea behind this is that by doing this we create a symmetry
between the getting and setting of config data in that we have a function
for both. In addition it will make it easier for us to identify the bits
that are related to init versus the pieces that are a wrapper for reading
data from the ACPI interface.
So for example by splitting things out like this it becomes much more
obvious that we were performing checks that weren't necessarily related to
the set/get operations such as relying on ndd->data being present when the
set and get ops should not care about a locally cached copy of the label
area.
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch removes an empty statement from an if expression and promotes
the else statement to the if expression with the expression logic reversed.
I feel this is more readable as the empty statement can lead to issues if
any additional logic was ever added.
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When working on the label code I found it rather confusing to see several
spots that reference a minimum label size of 256 while working with labels
that are 128 bytes in size.
This patch is meant to provide a clarification on one of the comments that
was at the heart of the issue. Specifically for version 1.2 and later of
the namespace specification the minimum label size is 256, prior to that
the minimum label size was 128. So we should state that as such to avoid
confusion.
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds validation for the labeloff field in the indexes.
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fix a leak of afs_server structs. The routine that installs them in the
various lookup lists and trees gets a ref on leaving the function, whether
it added the server or a server already exists. It shouldn't increment
the refcount if it added the server.
The effect of this that "rmmod kafs" will hang waiting for the leaked
server to become unused.
Fixes: d2ddc776a4 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just drop the "linux" part of the path, it was never correct.
Reported-by: Joe Perches <joe@perches.com>
Fixes: 256ac03750 ("dt-bindings: document devicetree bindings for mux-controllers and gpio-mux")
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file is GPL v2 or later.
Acked-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that the fix in commit 6636c3cc56 is bad; the assertion
that the iomap code no longer creates buffer heads is incorrect for
filesystems that set the IOMAP_F_BUFFER_HEAD flag.
Instead, what's happening is that gfs2_iomap_begin_write treats all
files that have the jdata flag set as journaled files, which is
incorrect as long as those files are inline ("stuffed"). We're handling
stuffed files directly via the page cache, which is why we ended up with
pages without buffer heads in gfs2_page_add_databufs.
Fix this by handling stuffed journaled files correctly in
gfs2_iomap_begin_write.
This reverts commit 6636c3cc5690c11631e6366cf9a28fb99c8b25bb.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
It doesn't make sense for a perf event to be configured as a CHAIN event
in isolation, so extend the arm_pmu structure with a ->filter_match()
function to allow the backend PMU implementation to reject CHAIN events
early.
Cc: <stable@vger.kernel.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We describe ranges of 'reserved' memory to userspace via /proc/iomem.
Commit 50d7ba36b9 ("arm64: export memblock_reserve()d regions via
/proc/iomem") updated the logic to export regions that were reserved
because their contents should be preserved. This allowed kexec-tools
to tell the difference between 'reserved' memory that must be
preserved and not overwritten, (e.g. the ACPI tables), and 'nomap'
memory that must not be touched without knowing the memory-attributes
(e.g. RAS CPER regions).
The above commit wrongly assumed that memblock_reserve() would not
be used to reserve regions that aren't memory. It turns out this is
exactly what early_init_dt_reserve_memory_arch() will do if it finds
a DT reserved-memory that was also carved out of the memory node, which
results in a WARN_ON_ONCE() and the region being reserved instead of
ignored. The ramoops description on hikey and dragonboard-410c both do
this, so we can't simply write this configuration off as "buggy firmware".
Avoid this issue by rewriting reserve_memblock_reserved_regions() so
that only the portions of reserved regions which overlap with mapped
memory are actually reserved.
Fixes: 50d7ba36b9 ("arm64: export memblock_reserve()d regions via /proc/iomem")
Reported-by: John Stultz <john.stultz@linaro.org>
Reported-by: Paolo Pisati <p.pisati@gmail.com>
CC: Akashi Takahiro <takahiro.akashi@linaro.org>
CC: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
It's possible for ext4_show_quota_options() to try reading
s_qf_names[i] while it is being modified by ext4_remount() --- most
notably, in ext4_remount's error path when the original values of the
quota file name gets restored.
Reported-by: syzbot+a2872d6feea6918008a9@syzkaller.appspotmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org # 3.2+
Function rgblk_free can only deal with one resource group at a time, so
pass that resource group is as a parameter. Several of the callers
already have the resource group at hand, so we only need additional
lookup code in a few places.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Reviewed-by: Steven Whitehouse <swhiteho@redhat.com>
The state parameter of gfs2_rlist_alloc is set to LM_ST_EXCLUSIVE in all
calls, so remove it and hardcode that state in gfs2_rlist_alloc instead.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Reviewed-by: Steven Whitehouse <swhiteho@redhat.com>
Reservations in gfs can span multiple gfs2_bitmaps (but they won't span
multiple resource groups). When removing a reservation, we want to
clear the GBF_FULL flags of all involved gfs2_bitmaps, not just that of
the first bitmap.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Reviewed-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Reviewed-by: Steven Whitehouse <swhiteho@redhat.com>
This field indicates the size of the bitmap in bytes, similar to how the
bi_blocks field indicates the size of the bitmap in blocks.
In count_unlinked, replace an instance of bi_bytes * GFS2_NBBY by
bi_blocks.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Reviewed-by: Steven Whitehouse <swhiteho@redhat.com>
This definition is only used to define RGRP_RSRV_MINBLKS, with no
benefit over defining RGRP_RSRV_MINBLKS directly.
In addition, instead of forcing RGRP_RSRV_MINBLKS to be of type u32,
cast it to that type where that type is required.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Reviewed-by: Steven Whitehouse <swhiteho@redhat.com>
Move the rs_sizehint and rs_rgd_gh fields from struct gfs2_blkreserv
into the inode: they are more closely related to the inode than to a
particular reservation.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Reviewed-by: Steven Whitehouse <swhiteho@redhat.com>
We already have a function that checks if a block is within a resource
group, so use that in gfs2_rbm_from_block as well.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Reviewed-by: Steven Whitehouse <swhiteho@redhat.com>
When gfs2_rbm_from_block fails, the rbm it returns is undefined, so we
always want to make sure gfs2_rbm_from_block has succeeded before
looking at the rbm.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Reviewed-by: Steven Whitehouse <swhiteho@redhat.com>
This patch sends a uevent (KOBJ_CHANGE) on the pwmchipN device,
everytime a pwmX channel has been exported/unexported via sysfs. This
allows udev to implement rules on such events, like:
SUBSYSTEM=="pwm*", PROGRAM="/bin/sh -c '\
chown -R root:gpio /sys/class/pwm && chmod -R 770 /sys/class/pwm;\
chown -R root:gpio
/sys/devices/platform/soc/*.pwm/pwm/pwmchip* && chmod -R 770
/sys/devices/platform/soc/*.pwm/pwm/pwmchip*\
'"
This is a replacement patch for commit 7e5d1fd75c ("pwm: Set class for
exported channels in sysfs"), see [1].
basic testing:
$ udevadm monitor --environment &
$ echo 0 > /sys/class/pwm/pwmchip0/export
KERNEL[197.321736] change /devices/.../pwm/pwmchip0 (pwm)
ACTION=change
DEVPATH=/devices/.../pwm/pwmchip0
EXPORT=pwm0
SEQNUM=2045
SUBSYSTEM=pwm
[1] https://lkml.org/lkml/2018/9/25/713
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Tested-by: Gottfried Haider <gottfried.haider@gmail.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This reverts commit 7e5d1fd75c ("pwm: Set
class for exported channels in sysfs") as it causes regression with
multiple pwm chip[1], when exporting a pwm channel (echo X > export):
- ABI (Documentation/ABI/testing/sysfs-class-pwm) states pwmX should be
created in /sys/class/pwm/pwmchipN/pwmX
- Reverted patch causes new entry to be also created directly in
/sys/class/pwm/pwmX
- 1st time, exporting pwmX will create an entry in /sys/class/pwm/pwmX
- class attributes are added under pwmX folder, such as export, unexport
npwm, symlinks. This is wrong as it belongs to pwmchipN. It may cause
bad behavior and report wrong values.
- when another export happens on another pwmchip, it can't be created
(e.g. -EEXIST). This is causing the issue with multiple pwmchip.
Example on stm32 (stm32429i-eval) platform:
$ ls /sys/class/pwm
pwmchip0 pwmchip4
$ cd /sys/class/pwm/pwmchip0/
$ echo 0 > export
$ ls /sys/class/pwm
pwm0 pwmchip0 pwmchip4
$ cd /sys/class/pwm/pwmchip4/
$ echo 0 > export
sysfs: cannot create duplicate filename '/class/pwm/pwm0'
...Exception stack follows...
This is also seen on other platform [2]
[1] https://lkml.org/lkml/2018/9/25/713
[2] https://lkml.org/lkml/2018/9/25/447
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Tested-by: Gottfried Haider <gottfried.haider@gmail.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Document r8a7744 specific compatible strings. No driver change is
needed as the fallback compatible string "renesas,tpu" activates the
right code in the driver.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Document the R-Car V3{M|H} (R8A779{7|8}0) SoC in the Renesas TPU
bindings; the TPU hardware in those is the Renesas standard 4-channel
timer pulse unit.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Document the R-Car V3{M|H} (R8A779{7|8}0) SoC in the Renesas R-Car PWM
bindings. R8A77970's hardware is a generic R-Car gen3 PWM, while R8A77980
has an extra error injection register...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The "compatible" property description contradicts even the example given:
it only says that there must be a single value while the example has the
fallback value too -- which makes much more sense. Moreover, the generic
property value is misdocumented as being R-Car (and RZ/G1) specific...
Fixes: 382457e562 ("pwm: renesas-tpu: Add DT support")
Fixes: 3ba111a018 ("dt-bindings: pwm: renesas-tpu: Document r8a774[35] support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>