Let's isolate the impact of cpu frequency selection on determing the GPU
throughput in response to selection of RPS frequencies.
For real systems, we do have to be concerned with the impact of
integrating c-states, p-states and rp-states, but for the sake of
proving whether or not RPS works, one baby step at a time.
For the record, as one would hope, it does not seem to impact on the
measured performance, but we do it anyway to reduce the number of
variables. Later, we can extend the testing to encourage the the
cpu/pkg to try and sleep while the GPU is busy.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200421142236.8614-1-chris@chris-wilson.co.uk
Link: https://patchwork.freedesktop.org/patch/msgid/20200421142236.8614-1-chris@chris-wilson.co.uk
The register RKISP1_CIF_MI_XTD_FORMAT_CTRL is currently written
with "on" only if the u,v streams need to be swapped. This patch
also write to it with "off" if they don't need to be swapped.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If we detect that the RPS end points do not scale perfectly, take the
time to measure all the in between values as well. We are aborting the
test, so we might as well spend the available time gathering critical
debug information instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200421124636.22554-1-chris@chris-wilson.co.uk
The value RKISP1_CIF_MI_XTD_FMT_CTRL_SP_CB_CR_SWAP should be
set to the register instead of masking with ~BIT(1)
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The value RKISP1_CIF_MI_XTD_FMT_CTRL_MP_CB_CR_SWAP equals BIT(0),
Therefore when writing it to the register there is no need to mask
it first with ~BIT(0).
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add common (Full-)HD definitions also known as 720p and 1080p.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the encoder enables the rate control algorithms if the bitrate
control is non-zero. Implement the V4L2_CID_MPEG_VIDEO_FRAME_RC_ENABLE
and V4L2_CID_MPEG_VIDEO_MB_RC_ENABLE controls to allow userspace to
choose frame-level or macroblock-level rate control updates, or to
explicitly disable rate control. Both controls are initially enabled to
keep the current behavior.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
don't call 'v4l2_async_notifier_parse_fwnode_endpoints_by_port'
in order to register async subdevices. Instead call
'v4l2_fwnode_endpoint_parse' to parse the remote endpoints
and then register each async subdev with
'v4l2_async_notifier_add_fwnode_remote_subdev'
Also remove the relevant item in the TODO file
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
'struct v4l2_mbus_config' is a legacy struct that should not be used
in new drivers. So replace it with the fields:
enum v4l2_mbus_type mbus_type;
unsigned int mbus_flags;
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We're very close to enforcing W^X memory, refuse to load modules that
violate this principle per construction.
[jeyu: move module_enforce_rwx_sections under STRICT_MODULE_RWX as per discussion]
Link: http://lore.kernel.org/r/20200403171303.GK20760@hirez.programming.kicks-ass.net
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
The clock provider may not be ready by the time spi-bcm-qspi gets
probed, handle probe deferral using devm_clk_get_optional().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200420190853.45614-2-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we set the tx/rx buffer to 0xff when NULL. This causes
problems with some spi slaves where 0xff is a valid command. Looking
at other drivers, the tx/rx buffer is usually set to 0x00 when NULL.
Following this convention solves the issue.
Fixes: fa236a7ef2 ("spi: bcm-qspi: Add Broadcom MSPI driver")
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200420190853.45614-6-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SCMI only passes clk_prepare_enable() and clk_disable_unprepare(), made
changes to suspend/resume ops to use the appropriate calls so that PM
works for ARM and ARM64 platforms.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Link: https://lore.kernel.org/r/20200420190853.45614-7-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As per the spi core implementation for MSPI devices when the transfer is
the last one in the message, the chip may stay selected until the next
transfer. On multi-device SPI busses with nothing blocking messages going
to other devices, this is just a performance hint; starting a message to
another device deselects this one. But in other cases, this can be used
to ensure correctness. Some devices need protocol transactions to be built
from a series of spi_message submissions, where the content of one message
is determined by the results of previous messages and where the whole
transaction ends when the chipselect goes intactive.
On CS change after completing the last serial transfer, the MSPI driver
drives SSb pin CDRAM register correctly according comments in core spi.h
as shown below:
case 1) EOM =1, cs_change =0: SSb inactive
case 2) EOM =1, cs_change =1: SSb active
case 3) EOM =0, cs_change =0: SSb active
case 4) EOM =0, cs_change =1: SSb inactive
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Link: https://lore.kernel.org/r/20200420190853.45614-5-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to support simultaneous streaming from both capture devices,
start/stop vb2 calls need to be serialized to allow multiple concurrent
calls.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If no errors occurs, pm functions return usage counters, so they can
return positive numbers.
This happens when streaming from multiple capture devices (mainpath and
selfpath).
Fix simultaneous streaming from mainpath and selfpath by not failing
when pm usage counters returns a positive number.
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rather than creating new compound control helpers for each new
type, create one generic function and just create defines on
top.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We use a spinlock while we are reading and accessing the destination address for a server.
We need to also use this spinlock to protect when we are modifying this address from
reconn_set_ipaddr().
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Christof Meerwald <cmeerw@cmeerw.org> writes:
> Hi,
>
> this is probably related to commit
> 7a0cf09494 (signal: Correct namespace
> fixups of si_pid and si_uid).
>
> With a 5.6.5 kernel I am seeing SIGCHLD signals that don't include a
> properly set si_pid field - this seems to happen for multi-threaded
> child processes.
>
> A simple test program (based on the sample from the signalfd man page):
>
> #include <sys/signalfd.h>
> #include <signal.h>
> #include <unistd.h>
> #include <spawn.h>
> #include <stdlib.h>
> #include <stdio.h>
>
> #define handle_error(msg) \
> do { perror(msg); exit(EXIT_FAILURE); } while (0)
>
> int main(int argc, char *argv[])
> {
> sigset_t mask;
> int sfd;
> struct signalfd_siginfo fdsi;
> ssize_t s;
>
> sigemptyset(&mask);
> sigaddset(&mask, SIGCHLD);
>
> if (sigprocmask(SIG_BLOCK, &mask, NULL) == -1)
> handle_error("sigprocmask");
>
> pid_t chldpid;
> char *chldargv[] = { "./sfdclient", NULL };
> posix_spawn(&chldpid, "./sfdclient", NULL, NULL, chldargv, NULL);
>
> sfd = signalfd(-1, &mask, 0);
> if (sfd == -1)
> handle_error("signalfd");
>
> for (;;) {
> s = read(sfd, &fdsi, sizeof(struct signalfd_siginfo));
> if (s != sizeof(struct signalfd_siginfo))
> handle_error("read");
>
> if (fdsi.ssi_signo == SIGCHLD) {
> printf("Got SIGCHLD %d %d %d %d\n",
> fdsi.ssi_status, fdsi.ssi_code,
> fdsi.ssi_uid, fdsi.ssi_pid);
> return 0;
> } else {
> printf("Read unexpected signal\n");
> }
> }
> }
>
>
> and a multi-threaded client to test with:
>
> #include <unistd.h>
> #include <pthread.h>
>
> void *f(void *arg)
> {
> sleep(100);
> }
>
> int main()
> {
> pthread_t t[8];
>
> for (int i = 0; i != 8; ++i)
> {
> pthread_create(&t[i], NULL, f, NULL);
> }
> }
>
> I tried to do a bit of debugging and what seems to be happening is
> that
>
> /* From an ancestor pid namespace? */
> if (!task_pid_nr_ns(current, task_active_pid_ns(t))) {
>
> fails inside task_pid_nr_ns because the check for "pid_alive" fails.
>
> This code seems to be called from do_notify_parent and there we
> actually have "tsk != current" (I am assuming both are threads of the
> current process?)
I instrumented the code with a warning and received the following backtrace:
> WARNING: CPU: 0 PID: 777 at kernel/pid.c:501 __task_pid_nr_ns.cold.6+0xc/0x15
> Modules linked in:
> CPU: 0 PID: 777 Comm: sfdclient Not tainted 5.7.0-rc1userns+ #2924
> Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
> RIP: 0010:__task_pid_nr_ns.cold.6+0xc/0x15
> Code: ff 66 90 48 83 ec 08 89 7c 24 04 48 8d 7e 08 48 8d 74 24 04 e8 9a b6 44 00 48 83 c4 08 c3 48 c7 c7 59 9f ac 82 e8 c2 c4 04 00 <0f> 0b e9 3fd
> RSP: 0018:ffffc9000042fbf8 EFLAGS: 00010046
> RAX: 000000000000000c RBX: 0000000000000000 RCX: ffffc9000042faf4
> RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff81193d29
> RBP: ffffc9000042fc18 R08: 0000000000000000 R09: 0000000000000001
> R10: 000000100f938416 R11: 0000000000000309 R12: ffff8880b941c140
> R13: 0000000000000000 R14: 0000000000000000 R15: ffff8880b941c140
> FS: 0000000000000000(0000) GS:ffff8880bca00000(0000) knlGS:0000000000000000
> CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
> CR2: 00007f2e8c0a32e0 CR3: 0000000002e10000 CR4: 00000000000006f0
> Call Trace:
> send_signal+0x1c8/0x310
> do_notify_parent+0x50f/0x550
> release_task.part.21+0x4fd/0x620
> do_exit+0x6f6/0xaf0
> do_group_exit+0x42/0xb0
> get_signal+0x13b/0xbb0
> do_signal+0x2b/0x670
> ? __audit_syscall_exit+0x24d/0x2b0
> ? rcu_read_lock_sched_held+0x4d/0x60
> ? kfree+0x24c/0x2b0
> do_syscall_64+0x176/0x640
> ? trace_hardirqs_off_thunk+0x1a/0x1c
> entry_SYSCALL_64_after_hwframe+0x49/0xb3
The immediate problem is as Christof noticed that "pid_alive(current) == false".
This happens because do_notify_parent is called from the last thread to exit
in a process after that thread has been reaped.
The bigger issue is that do_notify_parent can be called from any
process that manages to wait on a thread of a multi-threaded process
from wait_task_zombie. So any logic based upon current for
do_notify_parent is just nonsense, as current can be pretty much
anything.
So change do_notify_parent to call __send_signal directly.
Inspecting the code it appears this problem has existed since the pid
namespace support started handling this case in 2.6.30. This fix only
backports to 7a0cf09494 ("signal: Correct namespace fixups of si_pid and si_uid")
where the problem logic was moved out of __send_signal and into send_signal.
Cc: stable@vger.kernel.org
Fixes: 6588c1e3ff ("signals: SI_USER: Masquerade si_pid when crossing pid ns boundary")
Ref: 921cf9f630 ("signals: protect cinit from unblocked SIG_DFL signals")
Link: https://lore.kernel.org/lkml/20200419201336.GI22017@edge.cmeerw.net/
Reported-by: Christof Meerwald <cmeerw@cmeerw.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
If the v4l2_ctrl_g_ctrl*() or __v4l2_ctrl_s_ctrl*() functions
are called for the wrong control type then they call WARN_ON
since that is a driver error. But they still continue, potentially
overwriting data. Change this to return an error (s_ctrl) or 0
(g_ctrl), just to be safe.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tegra PMC clock clk_out_1 is dedicated for audio mclk from Tegra30
through Tegra210 and currently Tegra clock driver keeps the audio mclk
enabled.
With the move of PMC clocks from clock driver into pmc driver, audio
mclk enable from clock driver is removed and this should be taken care
of by the audio driver.
tegra_asoc_utils_init() calls tegra_asoc_utils_set_rate() and audio mclk
rate configuration is not needed during init and the rate is actually
set during the ->hw_params() callback.
So, this patch removes tegra_asoc_utils_set_rate() call and just leaves
the audio mclk enabled.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra PMC clock clk_out_1 is dedicated for audio mclk from Tegra30
through Tegra210 and currently Tegra clock driver does the initial
parent configuration for audio mclk and keeps it enabled by default.
With the move of PMC clocks from clock driver into PMC driver, audio
clocks parent configuration can be specified through the device tree
using assigned-clock-parents property and audio mclk control should be
taken care of by the audio driver.
This patch has implementation for parent configuration when default
parent configuration through assigned-clock-parents property is not
specified in the device tree.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra clk_out_1, clk_out_2, and clk_out_3 are part of PMC block and
these clocks are moved from the clock driver to PMC driver with PMC as
a provider for these clocks.
Update bindings document to use PMC as clock provider for clk_out_2 and
change ID to PMC clock ID.
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
tegra_asoc_utils uses clk_get() to get the clock and clk_put() to free
them explicitly.
This patch updates it to use device managed resource API devm_clk_get()
so the clock will be automatically released and freed when the device is
unbound and removes tegra_asoc_utils_fini() as its no longer needed.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A direct write to a APxxKey_EL1 register requires a context
synchronization event to ensure that indirect reads made by subsequent
instructions (e.g. AUTIASP, PACIASP) observe the new value.
When we initialize the boot task's APIAKey in boot_init_stack_canary()
via ptrauth_keys_switch_kernel() we miss the necessary ISB, and so there
is a window where instructions are not guaranteed to use the new APIAKey
value. This has been observed to result in boot-time crashes where
PACIASP and AUTIASP within a function used a mixture of the old and new
key values.
Fix this by having ptrauth_keys_switch_kernel() synchronize the new key
value with an ISB. At the same time, __ptrauth_key_install() is renamed
to __ptrauth_key_install_nosync() so that it is obvious that this
performs no synchronization itself.
Fixes: 2832158233 ("arm64: initialize ptrauth keys for kernel booting task")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Will Deacon <will@kernel.org>
Cc: Amit Daniel Kachhap <amit.kachhap@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Will Deacon <will@kernel.org>
Since commit 4957133fe3 ("media: lirc: improve locking"), drivers
do not need to do any of their own locking.
During suspend and resume, no processes are running so no locking is
needed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove vbi_regs_offset from a group of registers that are 888 specific,
include those registers names. Sources used for reference are 885 and 888
datasheets.
Add labels to some undocumented registers.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CNR is already calculated, so populate DVBv5 CNR stat
during read_status.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add get_rf_strength callback to get RSSI from the tuner. DVBv5
stat cache is updated. get_rf_strength is called by tuner_core
for analog tuners and is also used by some bridge drivers to
obtain RSSI directly from the tuner.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The boards listed below use i2c device drivers and have
tuner_type equal TUNER_ABSENT. This means additional support
is required to enable the analog tuning capability, a case
statement is used to identify these models.
Models with analog tuning enabled:
- CX231XX_BOARD_HAUPPAUGE_930C_HD_1114xx (tested)
- CX231XX_BOARD_HAUPPAUGE_935C (tested)
- CX231XX_BOARD_HAUPPAUGE_955Q (tested)
- CX231XX_BOARD_HAUPPAUGE_975 (tested)
- CX231XX_BOARD_EVROMEDIA_FULL_HYBRID_FULLHD (untested)
The EvroMedia model was added, since it uses the si2157
tuner and the board profile claims it has analog inputs.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hauppauge QuadHD/1265/5525 boards all use i2c device drivers and
have tuner_type equal TUNER_ABSENT. This means additional support
is required to enable the analog tuning capability, a case
statement is used to identify these models.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enables the analog tuning frontend for Hauppauge HVR-5525.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enables the analog tuning frontend for Hauppauge HVR-1265_K4.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add analog tuner frontend to 888 Hauppauge QuadHD boards
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In some debugging cases it is useful to know how long it took
signal lock to happen after tuning. This can help diagnose
line issues.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To detect errors in the tuning operation, this waits up 40ms for operation
completion status. This allows for error detection and prevents issuing
additional commands to the tuner before it is finished.
Tuning typically completes in 20-30ms.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Include set_analog_params, get_frequency, and get_bandwidth.
Tested with NTSC and PAL standards via ch3/4 generator. Other standards
are included, but are untested due to lack of generator.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Getting the Xtal trim property to check if running is less error prone.
Reset if_frequency if state is unknown.
Replaces the previous "garbage check".
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Check error status bit on command execute, if error bit is
set return -EAGAIN. Ignore -EAGAIN in probe during device check.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enable flags to get status of commands sent to the tuner.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After suspend & resume, wm8960_hw_params may be called when
bias_level is not SND_SOC_BIAS_ON, then wm8960_configure_clocking
is not called. But if sample rate is changed at that time, then
the output clock rate will be not correct.
So judgement of bias_level is SND_SOC_BIAS_ON in wm8960_hw_params
is not necessary and it causes above issue.
Fixes: 3176bf2d7c ("ASoC: wm8960: update pll and clock setting function")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1587468525-27514-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The default control endpoint ep0 can return a STALL indicating the
device does not support the control transfer requests. This is called
a protocol stall and does not halt the endpoint.
xHC behaves a bit different. Its internal endpoint state will always
be halted on any stall, even if the device side of the endpiont is not
halted. So we do need to issue the reset endpoint command to clear the
xHC host intenal endpoint halt state, but should not request the HS hub
to clear the TT buffer unless device side of endpoint is halted.
Clearing the hub TT buffer at protocol stall caused ep0 to become
unresponsive for some FS/LS devices behind HS hubs, and class drivers
failed to set the interface due to timeout:
usb 1-2.1: 1:1: usb_set_interface failed (-110)
Fixes: ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
Cc: <stable@vger.kernel.org> # v5.3
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspending the bus and host controller while a port is in a over-current
condition may halt the host.
Also keep the roothub running if over-current is active.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a class driver cancels its only URB then the endpoint ring buffer will
appear empty to the xhci driver. xHC hardware may still process cached
TRBs, and complete with a STALL, halting the endpoint.
This halted endpoint was not handled correctly by xhci driver as events on
empty rings were all assumed to be spurious events.
xhci driver refused to restart the ring with EP_HALTED flag set, so class
driver was never informed the endpoint halted even if it queued new URBs.
The host side of the endpoint needs to be reset, and dequeue pointer should
be moved in order to clear the cached TRBs and resetart the endpoint.
Small adjustments in finding the new dequeue pointer are needed to support
the case of stall on an empty ring and unknown current TD.
Cc: <stable@vger.kernel.org>
cc: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current code, if CONFIG_SWIOTLB is set, when failed to get IO TLB
memory from the low pages by plat_swiotlb_setup(), it may lead to the boot
process failed with kernel panic.
(1) On the Loongson and SiByte platform
arch/mips/loongson64/dma.c
arch/mips/sibyte/common/dma.c
void __init plat_swiotlb_setup(void)
{
swiotlb_init(1);
}
kernel/dma/swiotlb.c
void __init
swiotlb_init(int verbose)
{
...
vstart = memblock_alloc_low(PAGE_ALIGN(bytes), PAGE_SIZE);
if (vstart && !swiotlb_init_with_tbl(vstart, io_tlb_nslabs, verbose))
return;
...
pr_warn("Cannot allocate buffer");
no_iotlb_memory = true;
}
phys_addr_t swiotlb_tbl_map_single()
{
...
if (no_iotlb_memory)
panic("Can not allocate SWIOTLB buffer earlier ...");
...
}
(2) On the Cavium OCTEON platform
arch/mips/cavium-octeon/dma-octeon.c
void __init plat_swiotlb_setup(void)
{
...
octeon_swiotlb = memblock_alloc_low(swiotlbsize, PAGE_SIZE);
if (!octeon_swiotlb)
panic("%s: Failed to allocate %zu bytes align=%lx\n",
__func__, swiotlbsize, PAGE_SIZE);
...
}
Because IO_TLB_DEFAULT_SIZE is 64M, if the rest size of low memory is less
than 64M when call plat_swiotlb_setup(), we can easily reproduce the panic
case.
In order to reduce the possibility of kernel panic when failed to get IO
TLB memory under CONFIG_SWIOTLB, it is better to allocate low memory as
small as possible before plat_swiotlb_setup(), so make sparse_init() using
top-down allocation.
Reported-by: Juxin Gao <gaojuxin@loongson.cn>
Co-developed-by: Juxin Gao <gaojuxin@loongson.cn>
Signed-off-by: Juxin Gao <gaojuxin@loongson.cn>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
In the current code, plat_mem_setup() is called by arch_mem_init() instead
of setup_arch() and has been declared in asm/bootinfo.h, so modify the code
comment to reflect the reality and remove the useless duplicate declartion
in arch/mips/kernel/setup.c.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix the following checkpatch error:
ERROR: do not initialise globals to 0
#834: FILE: arch/mips/kernel/setup.c:834:
+int hw_coherentio = 0; /* Actual hardware supported DMA coherency setting. */
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
- Fix a regression introduced in the last merge window, which results
in guests in HPT mode dying randomly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJeni/pAAoJEJ2a6ncsY3GfTRoIANAQjIZi96AfJcfnrYQ4yUF7
scxawTiJ9VavvsEJLJ7vsozrJ4xxmvmA0fFWC84uw9+BwPqoLFFvZTjazbGEDVvF
FGwNBR/k7nfFVMIHS3K9iy9KjvYL3xkL26AgFTDJFq8hmOO9pH0txuk4r7SXb+NX
bGG0mScAD/Dg/HwAHAS6EP3jT35QtGTK62p8foqVTziTNcmBn9Ywtg0lEzAcq2iY
Y1BUD4Ov3cggshMI9SqHE8Yyq0XA2Wi6ggcyz/gVzvcbdFQmtg57Tri8nN8661LX
XKh+VTpYSIxNs5GgjwlNesJzJ9h6CSynJF556qrjQ0XsXcNqvn8fcZdNQ+hnRYw=
=Y19W
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into kvm-master
PPC KVM fix for 5.7
- Fix a regression introduced in the last merge window, which results
in guests in HPT mode dying randomly.
A page table upgrade in a kernel section that uses secondary address
mode will mess up the kernel instructions as follows:
Consider the following scenario: two threads are sharing memory.
On CPU1 thread 1 does e.g. strnlen_user(). That gets to
old_fs = enable_sacf_uaccess();
len = strnlen_user_srst(src, size);
and
" la %2,0(%1)\n"
" la %3,0(%0,%1)\n"
" slgr %0,%0\n"
" sacf 256\n"
"0: srst %3,%2\n"
in strnlen_user_srst(). At that point we are in secondary space mode,
control register 1 points to kernel page table and instruction fetching
happens via c1, rather than usual c13. Interrupts are not disabled, for
obvious reasons.
On CPU2 thread 2 does MAP_FIXED mmap(), forcing the upgrade of page table
from 3-level to e.g. 4-level one. We'd allocated new top-level table,
set it up and now we hit this:
notify = 1;
spin_unlock_bh(&mm->page_table_lock);
}
if (notify)
on_each_cpu(__crst_table_upgrade, mm, 0);
OK, we need to actually change over to use of new page table and we
need that to happen in all threads that are currently running. Which
happens to include the thread 1. IPI is delivered and we have
static void __crst_table_upgrade(void *arg)
{
struct mm_struct *mm = arg;
if (current->active_mm == mm)
set_user_asce(mm);
__tlb_flush_local();
}
run on CPU1. That does
static inline void set_user_asce(struct mm_struct *mm)
{
S390_lowcore.user_asce = mm->context.asce;
OK, user page table address updated...
__ctl_load(S390_lowcore.user_asce, 1, 1);
... and control register 1 set to it.
clear_cpu_flag(CIF_ASCE_PRIMARY);
}
IPI is run in home space mode, so it's fine - insns are fetched
using c13, which always points to kernel page table. But as soon
as we return from the interrupt, previous PSW is restored, putting
CPU1 back into secondary space mode, at which point we no longer
get the kernel instructions from the kernel mapping.
The fix is to only fixup the control registers that are currently in use
for user processes during the page table update. We must also disable
interrupts in enable_sacf_uaccess to synchronize the cr and
thread.mm_segment updates against the on_each-cpu.
Fixes: 0aaba41b58 ("s390: remove all code using the access register mode")
Cc: stable@vger.kernel.org # 4.15+
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
References: CVE-2020-11884
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
