The BCM63138 SATA PHY requires a special initialization sequence in
order to operate correctly, mostly tuning incorrect default values.
Implement that sequence and match the documented compatible string as an
entry point into that sequence.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Broadcom ARM-based DSL SoCs (BCM63xx product line) have the same
Broadcom SATA PHY that other SoCs are using, make it possible to select
that driver on these platforms.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Document the compatible string "brcm,bcm63138-sata-phy" as a valid
compatible string describing the standard Broadcom SATA PHY block.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a driver for PHY interface built into PCIe controller implemented
in UniPhier SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add DT bindings for PHY interface built into PCIe controller implemented
in UniPhier SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
From the AMD BKDG, if WAKE_INT_MASTER_REG.MaskStsEn is set, a software
write to the debounce registers of *any* gpio will block wake/interrupt
status generation for *all* gpios for a length of time that depends on
WAKE_INT_MASTER_REG.MaskStsLength[11:0]. During this period the Interrupt
Delivery bit (INTERRUPT_ENABLE) will read as 0.
In commit 4c1de0414a ("pinctrl/amd: poll InterruptEnable bits in
enable_irq") we tried to fix this same "gpio Interrupts are blocked
immediately after writing debounce registers" problem, but incorrectly
assumed it only affected the gpio whose debounce was being configured
and not ALL gpios.
To solve this for all gpios, we move the polling loop from
amd_gpio_irq_enable() to amd_gpio_irq_set_type(), while holding the gpio
spinlock. This ensures that another gpio operation (e.g.
amd_gpio_irq_unmask()) can read a temporarily disabled IRQ and
incorrectly disable it while trying to modify some other register bits.
Fixes: 4c1de0414a pinctrl/amd: poll InterruptEnable bits in enable_irq
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All SDHCI controller drivers are gathered at the same place, add the
Microchip one there.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Standardize the Microchip / Atmel entries with the same form and move them
so that they are all located at the same place, under the newer MICROCHIP
banner.
Only modifications to the titles of the entries are done in this patch.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
No need to keep this additional string as it can puzzle people
while adding new driver's entries.
Move the NAND entry to keep it alphabetically ordered.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add Eugen as co-maintainer with Ludovic of Microchip SAMA5D2-compatible
ADC driver.
Also add the binding documentation/include as file pattern.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add the entry that was missing for pwm-atmel.c driver. Add binding file
as well.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In Microchip DMA (HDMA actually) entry, add the missing files for
better matching with get_maintainer.pl tool.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Hand over this USB gadget driver to Cristian: atmel_usba.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Hand over to Codrin for Microchip Audio SoC drivers in "atmel"
directory.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
For ISC, Songjun is not with Microchip anymore, his address shouldn't be
reachable.
For ISI, Eugen can handle the maintenance now.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add Ludovic as a new co-maintainer for the AT91 Microchip ARM
sub-architecture.
Add the newly created kernel.org group git tree that we will use
from now on.
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
of_find_device_by_node takes a reference to the struct device when it
finds a match via get_device. but it fails to put_device in
at91_pm_config_ws, for_each_matching_node_and_match will get and put
the node properly, there is no need to call the of_put_node. Therefore,
just call put_device instead of of_node_put in at91_pm_config_ws.
Fixes: d7484f5c6b ("ARM: at91: pm: configure wakeup sources for ULP1 mode")
Suggested-by: Claudiu Beznea <Claudiu.Beznea@microchip.com>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Remove the unused local variable pvt:
drivers/edac/i7core_edac.c: In function 'i7core_mce_check_error':
drivers/edac/i7core_edac.c:1818:21: warning: variable 'pvt' set but not used \
[-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1537841043-108267-1-git-send-email-yuehaibing@huawei.com
Errata i870 is applicable in both EP and RC mode. Therefore rename
function dra7xx_pcie_ep_unaligned_memaccess(), that implements errata
workaround, to dra7xx_pcie_unaligned_memaccess() and call it for both RC
and EP. Make sure driver probe does not fail in case the workaround is not
applied for RC mode in order to maintain DT backward compatibility.
Reported-by: Chris Welch <Chris.Welch@viavisolutions.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
[lorenzo.pieralisi@arm.com: reworded the log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Update device tree binding documentation of TI's dra7xx PCI controller
for enabling unaligned mem access as applicable not just in EP mode but
in host mode as well.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Enable all necessary device tree nodes and add connector node to device
trees for all supported A64 boards with HDMI.
Jagan, tested on BPI-M64, OPI-Win, A64-Olinuxino, NPI-A64
Vasily, tested on pine64-lts
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Icenowy: squash all board patches altogether and change supply name]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner A64 have a display pipeline with 2 mixers/TCONs, the first
TCON is connected to LCD and the second is to HDMI.
The HDMI controller/PHY pair is similar to the one on H3/H5.
Add all required device tree nodes of the display pipeline, including
the TCON0 LCD one and the TCON1 HDMI one.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Icenowy: refactor commit message and add 1st pipeline]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180908134648.2582-20-noralf@tronnes.org
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
drm_fbdev_generic_setup() handles mode_config.num_connector being zero.
In that case it retries fbdev setup on the next .output_poll_changed.
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180908134648.2582-19-noralf@tronnes.org
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180908134648.2582-18-noralf@tronnes.org
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
If drm_fbdev_generic_setup() fails, an error is printed by the function.
drm_fbdev_generic_setup() handles mode_config.num_connector being zero.
In that case it retries fbdev setup on the next .output_poll_changed.
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180908134648.2582-14-noralf@tronnes.org
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180908134648.2582-13-noralf@tronnes.org
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
CONFIG_DRM_FBDEV_EMULATION wasn't honoured by the CMA helper, but it is by
drm_fb_helper.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180908134648.2582-12-noralf@tronnes.org
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180908134648.2582-10-noralf@tronnes.org
The CMA helper is already using the drm_fb_helper_generic_probe part of
the generic fbdev emulation. This patch makes full use of the generic
fbdev emulation by using its drm_client callbacks. This means that
drm_mode_config_funcs->output_poll_changed and drm_driver->lastclose are
now handled by the emulation code. Additionally fbdev unregister happens
automatically on drm_dev_unregister().
The drm_fbdev_generic_setup() call is put after drm_dev_register() in the
driver. This is done to highlight the fact that fbdev emulation is an
internal client that makes use of the driver, it is not part of the
driver as such. If fbdev setup fails, an error is printed, but the driver
succeeds probing.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180908134648.2582-9-noralf@tronnes.org
Improve error reporting in drm_fb_helper_fbdev_setup() by printing the
error code. This is useful for drivers that choose to not fall over just
because fbdev doesen't work, but still wants clues to why it failed.
This way they don't have to provide an error message themselves.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180908134648.2582-2-noralf@tronnes.org
perf test:
- Add watchpoint entry (Ravi Bangoria)
Build fixes:
- Initialize perf_data_file fd field to fix building the CTF (trace format)
converter with with gcc 4.8.4 on Ubuntu 14.04 (Jérémie Galarneau)
- Use -Wno-redundant-decls to build with PYTHON=python3 to
build the python binding, fixing the build in systems such
as Clear Linux (Arnaldo Carvalho de Melo)
Hardware tracing:
- Suppress AUX/OVERWRITE records (Alexander Shishkin)
Infrastructure:
- Adopt PTR_ERR_OR_ZERO from the kernel and use it in
the bpf-loader instead of open coded equivalent (Ding Xiang)
- Improve the event ordering code to make it clear and fix
a bug related to freeing of events when using pipe mode
from 'record' to 'inject' (Jiri Olsa)
- Some prep work to facilitate per-cpu threads to write
record data to per-cpu files (Jiri Olsa)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCW6JP9wAKCRCyPKLppCJ+
J9vjAQDfizmUwoCqgZD4q9d9hIx1KWrFK5q6EJOPsY+l0288BQEAzgx3Q0c7zFS1
WB0DjtGgEntudoH57vqsswrT7VPKPAE=
=Ee8x
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo-4.20-20180919' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
perf test improvements:
- Add watchpoint entry (Ravi Bangoria)
Build fixes:
- Initialize perf_data_file fd field to fix building the CTF (trace format)
converter with with gcc 4.8.4 on Ubuntu 14.04 (Jérémie Galarneau)
- Use -Wno-redundant-decls to build with PYTHON=python3 to
build the python binding, fixing the build in systems such
as Clear Linux (Arnaldo Carvalho de Melo)
Hardware tracing improvements:
- Suppress AUX/OVERWRITE records (Alexander Shishkin)
Infrastructure changes:
- Adopt PTR_ERR_OR_ZERO from the kernel and use it in
the bpf-loader instead of open coded equivalent (Ding Xiang)
- Improve the event ordering code to make it clear and fix
a bug related to freeing of events when using pipe mode
from 'record' to 'inject' (Jiri Olsa)
- Some prep work to facilitate per-cpu threads to write
record data to per-cpu files (Jiri Olsa)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave writes:
"Networking fixes:
1) Fix multiqueue handling of coalesce timer in stmmac, from Jose
Abreu.
2) Fix memory corruption in NFC, from Suren Baghdasaryan.
3) Don't write reserved bits in ravb driver, from Kazuya Mizuguchi.
4) SMC bug fixes from Karsten Graul, YueHaibing, and Ursula Braun.
5) Fix TX done race in mvpp2, from Antoine Tenart.
6) ipv6 metrics leak, from Wei Wang.
7) Adjust firmware version requirements in mlxsw, from Petr Machata.
8) Fix autonegotiation on resume in r8169, from Heiner Kallweit.
9) Fixed missing entries when dumping /proc/net/if_inet6, from Jeff
Barnhill.
10) Fix double free in devlink, from Dan Carpenter.
11) Fix ethtool regression from UFO feature removal, from Maciej
Żenczykowski.
12) Fix drivers that have a ndo_poll_controller() that captures the
cpu entirely on loaded hosts by trying to drain all rx and tx
queues, from Eric Dumazet.
13) Fix memory corruption with jumbo frames in aquantia driver, from
Friedemann Gerold."
* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (79 commits)
net: mvneta: fix the remaining Rx descriptor unmapping issues
ip_tunnel: be careful when accessing the inner header
mpls: allow routes on ip6gre devices
net: aquantia: memory corruption on jumbo frames
tun: remove ndo_poll_controller
nfp: remove ndo_poll_controller
bnxt: remove ndo_poll_controller
bnx2x: remove ndo_poll_controller
mlx5: remove ndo_poll_controller
mlx4: remove ndo_poll_controller
i40evf: remove ndo_poll_controller
ice: remove ndo_poll_controller
igb: remove ndo_poll_controller
ixgb: remove ndo_poll_controller
fm10k: remove ndo_poll_controller
ixgbevf: remove ndo_poll_controller
ixgbe: remove ndo_poll_controller
bonding: use netpoll_poll_dev() helper
netpoll: make ndo_poll_controller() optional
rds: Fix build regression.
...
This cleanup patch makes changes to use for_each_pipe loop
during bit-mask assignment of allowed crtc with encoder.
changes:
- use BIT(i) macro instead of (1 << i) (Chris)
changes from V2:
- use int for consistency (Jani)
changes from V3:
- instead use enum pipe (Ville)
changes from V4:
- drop DP/HDMI changes, as already part of patch from ville
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180919083126.31805-1-mahesh1.kumar@intel.com
In the iommu's shutdown handler we disable runtime-pm which could
result in the irq-handler running unclocked and since commit
3fc7c5c0cf ("iommu/rockchip: Handle errors returned from PM framework")
we warn about that fact.
This can cause warnings on shutdown on some Rockchip machines, so
free the irqs in the shutdown handler before we disable runtime-pm.
Reported-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Fixes: 3fc7c5c0cf ("iommu/rockchip: Handle errors returned from PM framework")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
PCI host drivers have already matched on compatible strings, so checking
device_type is redundant. Also, device_type is considered deprecated for
FDT though we've still been requiring it for PCI hosts as it is useful
for finding PCI buses.
Signed-off-by: Rob Herring <robh@kernel.org>
[lorenzo.pieralisi@arm.com: reformatted the log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Alan Douglas <adouglas@cadence.com>
Acked-by: Subrahmaya Lingappa <l.subrahmanya@mobiveil.co.in>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Alan Douglas <adouglas@cadence.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Whilst the symmetry of deferring to the existing sync callback in
__iommu_map_page() is nice, taking a round-trip through
iommu_iova_to_phys() is a pretty heavyweight way to get an address we
can trivially compute from the page we already have. Tweaking it to just
perform the cache maintenance directly when appropriate doesn't really
make the code any more complicated, and the runtime efficiency gain can
only be a benefit.
Furthermore, the sync operations themselves know they can only be
invoked on a managed DMA ops domain, so can use the fast specific domain
lookup to avoid excessive manipulation of the group refcount
(particularly in the scatterlist cases).
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Most parts of iommu-dma already assume they are operating on a default
domain set up by iommu_dma_init_domain(), and can be converted straight
over to avoid the refcounting bottleneck. MSI page mappings may be in
an unmanaged domain with an explicit MSI-only cookie, so retain the
non-specific lookup, but that's OK since they're far from a contended
fast path either way.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
While iommu_get_domain_for_dev() is the robust way for arbitrary IOMMU
API callers to retrieve the domain pointer, for DMA ops domains it
doesn't scale well for large systems and multi-queue devices, since the
momentary refcount adjustment will lead to exclusive cacheline contention
when multiple CPUs are operating in parallel on different mappings for
the same device.
In the case of DMA ops domains, however, this refcounting is actually
unnecessary, since they already imply that the group exists and is
managed by platform code and IOMMU internals (by virtue of
iommu_group_get_for_dev()) such that a reference will already be held
for the lifetime of the device. Thus we can avoid the bottleneck by
providing a fast lookup specifically for the DMA code to retrieve the
default domain it already knows it has set up - a simple read-only
dereference plays much nicer with cache-coherency protocols.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
As an optimisation for PCI devices, there is always first attempt
been made to allocate iova from SAC address range. This will lead
to unnecessary attempts, when there are no free ranges
available. Adding fix to track recently failed iova address size and
allow further attempts, only if requested size is lesser than a failed
size. The size is updated when any replenish happens.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Ganapatrao Kulkarni <ganapatrao.kulkarni@cavium.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
A patch from Ricardo got me thinking about some gpio chip
semantics so let's drop in some comments to make things
more clear around that.
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
fsl-mc bus support the new iommu-map property. Comply to this binding
for fsl_mc bus.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
of_dma_configure() API expects coherent_dma_mask to be correctly
set in the devices. This patch does the needful.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch adds support of dma configuration for devices on fsl-mc
bus using 'dma_configure' callback for busses. Also, directly calling
arch_setup_dma_ops is removed from the fsl-mc bus.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Implement bus specific support for the fsl-mc bus including
registering arm_smmu_ops and bus specific device add operations.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>