send netlink notification if neigh_update results in NTF_ROUTER
change and if NEIGH_UPDATE_F_ISROUTER is on. Also move the
NTF_ROUTER change function into a helper.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows admin setting of NTF_ROUTER flag
on a neighbour entry. This enables external control
plane (like bgp evpn) to manage neigh entries with
NTF_ROUTER flag.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Summary:
This appears to be necessary and sufficient change to enable `MPLS` on
`ip6gre` tunnels (RFC4023).
This diff allows IP6GRE devices to be recognized by MPLS kernel module
and hence user can configure interface to accept packets with mpls
headers as well setup mpls routes on them.
Test Plan:
Test plan consists of multiple containers connected via GRE-V6 tunnel.
Then carrying out testing steps as below.
- Carry out necessary sysctl settings on all containers
```
sysctl -w net.mpls.platform_labels=65536
sysctl -w net.mpls.ip_ttl_propagate=1
sysctl -w net.mpls.conf.lo.input=1
```
- Establish IP6GRE tunnels
```
ip -6 tunnel add name if_1_2_1 mode ip6gre \
local 2401:db00:21:6048:feed:0::1 \
remote 2401:db00:21:6048:feed:0::2 key 1
ip link set dev if_1_2_1 up
sysctl -w net.mpls.conf.if_1_2_1.input=1
ip -4 addr add 169.254.0.2/31 dev if_1_2_1 scope link
ip -6 tunnel add name if_1_3_1 mode ip6gre \
local 2401:db00:21:6048:feed:0::1 \
remote 2401:db00:21:6048:feed:0::3 key 1
ip link set dev if_1_3_1 up
sysctl -w net.mpls.conf.if_1_3_1.input=1
ip -4 addr add 169.254.0.4/31 dev if_1_3_1 scope link
```
- Install MPLS encap rules on node-1 towards node-2
```
ip route add 192.168.0.11/32 nexthop encap mpls 32/64 \
via inet 169.254.0.3 dev if_1_2_1
```
- Install MPLS forwarding rules on node-2 and node-3
```
// node2
ip -f mpls route add 32 via inet 169.254.0.7 dev if_2_4_1
// node3
ip -f mpls route add 64 via inet 169.254.0.12 dev if_4_3_1
```
- Ping 192.168.0.11 (node4) from 192.168.0.1 (node1) (where routing
towards 192.168.0.1 is via IP route directly towards node1 from node4)
```
ping 192.168.0.11
```
- tcpdump on interface to capture ping packets wrapped within MPLS
header which inturn wrapped within IP6GRE header
```
16:43:41.121073 IP6
2401:db00:21:6048:feed::1 > 2401:db00:21:6048:feed::2:
DSTOPT GREv0, key=0x1, length 100:
MPLS (label 32, exp 0, ttl 255) (label 64, exp 0, [S], ttl 255)
IP 192.168.0.1 > 192.168.0.11:
ICMP echo request, id 1208, seq 45, length 64
0x0000: 6000 2cdb 006c 3c3f 2401 db00 0021 6048 `.,..l<?$....!`H
0x0010: feed 0000 0000 0001 2401 db00 0021 6048 ........$....!`H
0x0020: feed 0000 0000 0002 2f00 0401 0401 0100 ......../.......
0x0030: 2000 8847 0000 0001 0002 00ff 0004 01ff ...G............
0x0040: 4500 0054 3280 4000 ff01 c7cb c0a8 0001 E..T2.@.........
0x0050: c0a8 000b 0800 a8d7 04b8 002d 2d3c a05b ...........--<.[
0x0060: 0000 0000 bcd8 0100 0000 0000 1011 1213 ................
0x0070: 1415 1617 1819 1a1b 1c1d 1e1f 2021 2223 .............!"#
0x0080: 2425 2627 2829 2a2b 2c2d 2e2f 3031 3233 $%&'()*+,-./0123
0x0090: 3435 3637 4567
```
Signed-off-by: Saif Hasan <has@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eelco Chaudron says:
====================
net/sched: Add hardware specific counters to TC actions
Add hardware specific counters to TC actions which will be exported
through the netlink API. This makes troubleshooting TC flower offload
easier, as it possible to differentiate the packets being offloaded.
v2 - Rebased on latest net-next
====================
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add additional counters that will store the bytes/packets processed by
hardware. These will be exported through the netlink interface for
displaying by the iproute2 tc tool
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new hardware specific basic counter, TCA_STATS_BASIC_HW. This can
be used to count packets/bytes processed by hardware offload.
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When debug is enabled, we want to see what devices we're detecting
to make things a bit easier for us. Many of these devices will also
be available on am335x and dra7, and some just need updating the
revision register mask.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to detect few new devices to tag for noirq_suspend and
pm_runtime_irq_safe to avoid causing regressions compared to
legacy platform data booting.
Let's update i2c, gpio, uart and wdt revision masks to detect
them on am437x. Note that we can remove the second wdt entry
with the updated mask. Note that we also have some uarts with
a different revision register.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We don't care when we suspend but some our children do. In order to
avoid tagging various modules with SYSC_QUIRK_RESOURCE_PROVIDER, let's
do it automatically by tagging modules that are busy on suspend for
noirq suspend. This way we can just do module detection on define DEBUG.
Note that we still need to keep SYSC_QUIRK_LEGACY_IDLE flag around so
the our legacy single-child devices that set pm_runtime_irq_safe() can
manage the interconnect target module themselves.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we don't need an override for BIOVEC_PHYS_MERGEABLE there is
no need to drag this header in.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We only use it in biovec_phys_mergeable and a m68k paravirt driver,
so just opencode it there. Also remove the pointless unsigned long cast
for the offset in the opencoded instances.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
These two checks should always be performed together, so merge them into
a single helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The actual recaculation of segments in __blk_recalc_rq_segments will
do this check, so there is no point in forcing it if we know it won't
succeed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Turn the macro into an inline, move it to blk.h and simplify the
arch hooks a bit.
Also rename the function to biovec_phys_mergeable as there is no need
to shout.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Keep it close to the actual users instead of exposing the function to all
drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A number of our interrupts were incorrectly specified, fix both the PPI
and SPI interrupts to be correct.
Fixes: b5762cacc4 ("ARM: bcm63138: add NAND DT support")
Fixes: 46d4bca044 ("ARM: BCM63XX: add BCM63138 minimal Device Tree")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
MMC host controller bindings and MMC core defines card detect pin as
active low. Therefore there is no point to invert it twice.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Daniel Borkmann says:
====================
pull-request: bpf 2018-09-24
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Several fixes for BPF sockmap to only allow sockets being attached in
ESTABLISHED state, from John.
2) Fix up the license to LGPL/BSD for the libc compat header which contains
fallback helpers that libbpf and bpftool is using, from Jakub.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Chevallier says:
====================
net: mvpp2: Add txq to CPU mapping
This short series adds XPS support to the mvpp2 driver, by mapping
txqs and CPUs. This comes with a patch using round-robin scheduling
for the HW to pick the next txq to transmit from, instead of the default
fixed-priority scheduling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit allows each TXQ to be picked in a round-robin fashion by
the PPv2 transmit scheduling mechanism. This is opposed to the default
behaviour that prioritizes the highest numbered queues.
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the PPv2 controller has multiple TX queues, we can spread traffic
by assining TX queues to CPUs, allowing to use XPS to balance egress
traffic between CPUs.
Suggested-by : Yan Markman <ymarkman@marvell.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The proper parent clock for audio subsystem for Exynos5420 and Exynos5800
SoCs is CLK_MAU_EPLL. This fixes following warning:
clk: failed to reparent mout_audss to fout_epll: -22
Fixes: ed7d130707: ARM: dts: exynos: Enable HDMI audio support on Peach Pit
Fixes: bae0f445c1: ARM: dts: exynos: Enable HDMI audio support on Peach Pi
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
For contiguous hugetlb, huge_ptep_set_access_flags performs a
get_clear_flush (which then flushes the TLBs) even when no change of ptes
is necessary.
Unfortunately, this behaviour can lead to back-to-back page faults being
generated when running with multiple threads that access the same
contiguous huge page.
Thread 1 | Thread 2
-----------------------------+------------------------------
hugetlb_fault |
huge_ptep_set_access_flags |
-> invalidate pte range | hugetlb_fault
continue processing | wait for hugetlb_fault_mutex
release mutex and return | huge_ptep_set_access_flags
| -> invalidate pte range
hugetlb_fault
...
This patch changes huge_ptep_set_access_flags s.t. we first read the
contiguous range of ptes (whilst preserving dirty information); the pte
range is only then invalidated where necessary and this prevents further
spurious page faults.
Fixes: d8bdcff287 ("arm64: hugetlb: Add break-before-make logic for contiguous entries")
Reported-by: Lei Zhang <zhang.lei@jp.fujitsu.com>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In the contiguous bit hugetlb break-before-make code we assume that all
hugetlb pages are young.
In fact, remove_migration_pte is able to place an old hugetlb pte so
this assumption is not valid.
This patch fixes the contiguous hugetlb scanning code to preserve young
ptes.
Fixes: d8bdcff287 ("arm64: hugetlb: Add break-before-make logic for contiguous entries")
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
KVM has an old optimization whereby accesses to the kernel GS base MSR
are trapped when the guest is in 32-bit and not when it is in 64-bit mode.
The idea is that swapgs is not available in 32-bit mode, thus the
guest has no reason to access the MSR unless in 64-bit mode and
32-bit applications need not pay the price of switching the kernel GS
base between the host and the guest values.
However, this optimization adds complexity to the code for little
benefit (these days most guests are going to be 64-bit anyway) and in fact
broke after commit 678e315e78 ("KVM: vmx: add dedicated utility to
access guest's kernel_gs_base", 2018-08-06); the guest kernel GS base
can be corrupted across SMIs and UEFI Secure Boot is therefore broken
(a secure boot Linux guest, for example, fails to reach the login prompt
about half the time). This patch just removes the optimization; the
kernel GS base MSR is now never trapped by KVM, similarly to the FS and
GS base MSRs.
Fixes: 678e315e78
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is an issue where the host is unable to tell the gadget what frame
rate it wants if the dwFrameIntervals in the interface descriptors are
not in ascending order. This means that when instantiating a uvc gadget
via configfs the user must make sure the dwFrameIntervals are in
ascending order.
Instead of silently failing the breaking of this rule, we sort the
dwFrameIntervals upon writing to configfs.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
While checks are in place to avoid attributes and children of a format
being manipulated after the format is linked into the streaming header,
the linked flag was never actually set, invalidating the protections.
Update the flag as appropriate in the header link calls.
Signed-off-by: Joel Pepper <joel.pepper@rwth-aachen.de>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
- Add bFrameIndex as a UVCG_FRAME_ATTR_RO for each frame size.
- Automatically assign ascending bFrameIndex to each frame in a format.
Before all "bFrameindex" attributes were set to "1" with no way to
configure the gadget otherwise. This resulted in the host always
negotiating for bFrameIndex 1 (i.e. the first frame size of the gadget).
After the negotiation the host driver will set the user or application
selected frame size, while the gadget is actually set to the first frame
size.
Now, when the containing format is linked into the streaming header,
iterate over all child frame descriptors and assign ascending indices.
The automatically assigned indices can be read from the new read only
bFrameIndex configfs attribute in each frame descriptor item.
Signed-off-by: Joel Pepper <joel.pepper@rwth-aachen.de>
[Simplified documentation, renamed function, blank space update]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
The UVC format description are numbered using the descriptor's
bFormatIndex field. The index is used in UVC requests, and is thus
needed to handle requests in userspace. Make it dynamically discoverable
by exposing it in a bFormatIndex configfs attribute of the uncompressed
and mjpeg format config items.
The bFormatIndex value exposed through the attribute is stored in the
config item private data. However, that value is never set: the driver
instead computes the bFormatIndex value when linking the stream class
header in the configfs hierarchy and stores it directly in the class
descriptors in a separate structure. In order to expose the value
through the configfs attribute, store it in the config item private data
as well. This results in a small code simplification.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
The video control and video streaming interface numbers are needed in
the UVC gadget userspace stack to reply to UVC requests. They are
hardcoded to fixed values at the moment, preventing configurations with
multiple functions.
To fix this, make them dynamically discoverable by userspace through
read-only configfs attributes in <function>/control/bInterfaceNumber and
<function>/streaming/bInterfaceNumber respectively.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
The UVC configfs implementation creates all groups as global static
variables. This prevents creation of multiple UVC function instances,
as they would all require their own configfs group instances.
Fix this by allocating all groups dynamically. To avoid duplicating code
around, extend the config_item_type structure with group name and
children, and implement helper functions to create children
automatically for most groups.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Some of the .allow_link() and .drop_link() operations implementations
call config_group_find_item() and then leak the reference to the
returned item. Fix this by dropping those references where needed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Add "marvell,prestera" as a compatible string so that drivers can be
written to account for any prestera variant without needing to
specialise to the more specific values.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Free Electrons is now called Bootlin, and my e-mail address was
changed as well, so this commit updates the entries in the MAINTAINERS
file accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
We need to maintain backwards compatibility with device trees that don't
define an enable method. At the same time we want the device tree to be
able to specify an enable-method and have it stick.
Previously by having smp assigned in the DT_MACHINE definition this
would be picked up by setup_arch() and override whatever
arm_dt_init_cpu_maps() had configured. Now we move the initial
assignment of default smp_ops to a dt_fixup and let
arm_dt_init_cpu_maps() override that if the device tree defines an
enable-method.
[olof@lixom.net: Wrap set_smp_ops() in CONFIG_SMP.]
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com> (on AX3)
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This introduces the Cedrus VPU driver that supports the VPU found in
Allwinner SoCs, also known as Video Engine. It is implemented through
a V4L2 M2M decoder device and a media device (used for media requests).
So far, it only supports MPEG-2 decoding.
Since this VPU is stateless, synchronization with media requests is
required in order to ensure consistency between frame headers that
contain metadata about the frame to process and the raw slice data that
is used to generate the frame.
This driver was made possible thanks to the long-standing effort
carried out by the linux-sunxi community in the interest of reverse
engineering, documenting and implementing support for the Allwinner VPU.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: dropped obsolete MEDIA_REQUEST_API from Kconfig]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch programs the time (in escape clocks) to drive
the link in the initialization (i.e. LP-11) state.
v2: Rebase
v3: Remove step hard coding comments (Jani N)
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1537095223-5184-5-git-send-email-madhav.chauhan@intel.com
This patch enables DDI buffer by writing to DDI_BUF_CTL
register and wait for DDI status to be *not idle* for a
port.
v2: Rebase
v3: Remove step hard coding comments (Jani N)
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1537095223-5184-4-git-send-email-madhav.chauhan@intel.com
This patch setup voltage swing before enabling
combo PHY DDI (shared with DSI).
Note that DSI voltage swing programming is for
high speed data buffers. HW automatically handles
the voltage swing for the low power data buffers.
v2: Rebase
v3: Address various review comments related to VSWING
programming (Jani N)
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1537095223-5184-3-git-send-email-madhav.chauhan@intel.com
This patch set the loadgen select and latency optimization for
aux and transmit lanes of combo phy transmitters. It will be
used for MIPI DSI HS operations.
v2: Rebase
v3: Add empty line to make code more legible (Ville).
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1537095223-5184-2-git-send-email-madhav.chauhan@intel.com
This adds a device-tree binding document that specifies the properties
used by the Cedrus VPU driver, as well as examples.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>