This adds a pair of context save/restore functions to save/restore the
state of a set of pinctrl registers. The context is lost during rtc only
suspend with ddr in self-refresh on am43xx. Currently the save/restore
is being done unconditionally. This will be optimized later with a
pdata-quirk function which will allow is to save/restore only when doing
the rtc only mode with ddr in self refresh.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The comment about offset zero was not updated when changing behavior:
- Automatic offset calculation is indicated by OFFSET_CONTINUOUS,
- Zero really means offset zero.
Fixes: b175d03dd2 ("[PATCH] mtd cmdlinepart: allow zero offset value")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This allows using bcm47xxpart parser to find partitions on flash
described in DT using the "brcm,bcm947xx-cfe-partitions" compatible
property. It means this parser doesn't have to be explicitly selected by
a flash driver anymore. It can be used e.g. together with a generic
m25p80 / spi-nor if device is just properly described.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Broadcom based home router devices use partitions which have to be
discovered in a specific way. They are not fixed and there is not any
standard partition table. This commit adds and describes a new custom
binding for such devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Syscon nodes can be a simple-mfd and the syscon-users then be declared
as children of this node. That way the parent-child structure can be
better represented for devices that are fully embedded in the syscon.
Therefore allow getting the syscon from the parent if neither
a special compatible nor a gpio,syscon-dev property is defined.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Auto rate table sent to firmware is getting corrupted
as memset to zeros is not done. Added memset to skb
data before filling auto rate table.
Signed-off-by: Sanjay Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Observed crash in some scenarios when assertion has occurred,
this is because hw structure is freed and is tried to get
accessed in some functions where null check is already
present. So, avoided the crash by making the hw to NULL after
freeing.
Signed-off-by: Sanjay Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This allows reading all capabilities as reported by a firmware. They are
printed using native (raw) names, just like developers like it the most.
It's how firmware reports support for various features, e.g. supported
modes, supported standards, power saving details, max BSS-es.
Access to all that info is useful for trying new firmwares, comparing
them and debugging features AKA bugs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Correct snr/nr/rssi data index to avoid possible buffer underflow.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usleep_range can cause excessive latency on channel change if waiting
for the MAC to stop fails. It will be forced to stop by the code
following that loop anyway.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Allows it to be shared between different drivers and locks to be
initialized earlier
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During scans, mac80211 frequently switches back to the home channel to
minimize interruption of ongoing traffic. Keep regular tx queues active
during that time.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Get the driver data directly by dev_get_drvdata.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the radio was previously in running state, it can receive some
packets before it is able to process them.
This can lead to a crash if the channel is not initialized yet.
Discard all rx packets until start() is called
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For encryption to work properly, the BSS index needs to be initialized
for the WCID entry used for the interface.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
According to 802.11-2007 17.3.8.6 (slot time), the slot time should
be increased by 3 us * coverage class. Taking into account coverage
class in slot time configuration allows to increase by an order of
magnitude the throughput on a 4Km link in a noisy environment
Tested-by: Luca Bisti <luca.bisti@gmail.com>
Tested-by: Gaetano Catalli <gaetano.catalli@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove the call to platform_get_irq use the cached
one instead.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Credit calculations for the packet ratelimiting are not correct, as per
the applied ratelimit of 25/second and burst 8, a total of 33 packets
should have been accepted. This is true in iptables(33) but not in
nftables (~65). For packet ratelimiting, use:
div_u64(limit->nsecs, limit->rate) * limit->burst;
to calculate credit, just like in iptables' xt_limit does.
Moreover, use default burst in iptables, users are expecting similar
behaviour.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ath.git patches for 4.18. Major changes:
ath10k
* add quiet mode support for QCA6174/QCA9377
wil6210
* disable WIL6210_TRACING kconfig option by default
ICU size in CP110 is not 0x10 but at least 0x440 bytes long (from the
specification).
Fixes: 6ef84a827c ("arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
In the nft_meta_set_eval, nftrace value is dereferenced as u32 from sreg.
But correct type is u8. so that sometimes incorrect value is dereferenced.
Steps to reproduce:
%nft add table ip filter
%nft add chain ip filter input { type filter hook input priority 4\; }
%nft add rule ip filter input nftrace set 0
%nft monitor
Sometimes, we can see trace messages.
trace id 16767227 ip filter input packet: iif "enp2s0"
ether saddr xx:xx:xx:xx:xx:xx ether daddr xx:xx:xx:xx:xx:xx
ip saddr 192.168.0.1 ip daddr 255.255.255.255 ip dscp cs0
ip ecn not-ect ip
trace id 16767227 ip filter input rule nftrace set 0 (verdict continue)
trace id 16767227 ip filter input verdict continue
trace id 16767227 ip filter input
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The RTC has a 64 bit counter.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In nfqueue, two consecutive skbuffs may race to create the conntrack
entry. Hence, the one that loses the race gets dropped due to clash in
the insertion into the hashes from the nf_conntrack_confirm() path.
This patch adds a new nf_conntrack_update() function which searches for
possible clashes and resolve them. NAT mangling for the packet losing
race is corrected by using the conntrack information that won race.
In order to avoid direct module dependencies with conntrack and NAT, the
nf_ct_hook and nf_nat_hook structures are used for this purpose.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In commit 47b7e7f828, this bit was removed at the same time the
RT6_LOOKUP_F_IFACE flag was removed. However, it is needed when
link-local addresses are used, which is a very common case: when
packets are routed, neighbor solicitations are done using link-local
addresses. For example, the following neighbor solicitation is not
matched by "-m rpfilter":
IP6 fe80::5254:33ff:fe00:1 > ff02::1:ff00:3: ICMP6, neighbor
solicitation, who has 2001:db8::5254:33ff:fe00:3, length 32
Commit 47b7e7f828 doesn't quite explain why we shouldn't use
RT6_LOOKUP_F_IFACE in the rpfilter case. I suppose the interface check
later in the function would make it redundant. However, the remaining
of the routing code is using RT6_LOOKUP_F_IFACE when there is no
source address (which matches rpfilter's case with a non-unicast
destination, like with neighbor solicitation).
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Fixes: 47b7e7f828 ("netfilter: don't set F_IFACE on ipv6 fib lookups")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before requesting the IRQ.
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This reverts commit f92b40a8b2
("netfilter: core: only allow one nat hook per hook point"), this
limitation is no longer needed. The nat core now invokes these
functions and makes sure that hook evaluation stops after a mapping is
created and a null binding is created otherwise.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently the packet rewrite and instantiation of nat NULL bindings
happens from the protocol specific nat backend.
Invocation occurs either via ip(6)table_nat or the nf_tables nat chain type.
Invocation looks like this (simplified):
NF_HOOK()
|
`---iptable_nat
|
`---> nf_nat_l3proto_ipv4 -> nf_nat_packet
|
new packet? pass skb though iptables nat chain
|
`---> iptable_nat: ipt_do_table
In nft case, this looks the same (nft_chain_nat_ipv4 instead of
iptable_nat).
This is a problem for two reasons:
1. Can't use iptables nat and nf_tables nat at the same time,
as the first user adds a nat binding (nf_nat_l3proto_ipv4 adds a
NULL binding if do_table() did not find a matching nat rule so we
can detect post-nat tuple collisions).
2. If you use e.g. nft_masq, snat, redir, etc. uses must also register
an empty base chain so that the nat core gets called fro NF_HOOK()
to do the reverse translation, which is neither obvious nor user
friendly.
After this change, the base hook gets registered not from iptable_nat or
nftables nat hooks, but from the l3 nat core.
iptables/nft nat base hooks get registered with the nat core instead:
NF_HOOK()
|
`---> nf_nat_l3proto_ipv4 -> nf_nat_packet
|
new packet? pass skb through iptables/nftables nat chains
|
+-> iptables_nat: ipt_do_table
+-> nft nat chain x
`-> nft nat chain y
The nat core deals with null bindings and reverse translation.
When no mapping exists, it calls the registered nat lookup hooks until
one creates a new mapping.
If both iptables and nftables nat hooks exist, the first matching
one is used (i.e., higher priority wins).
Also, nft users do not need to create empty nat hooks anymore,
nat core always registers the base hooks that take care of reverse/reply
translation.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This adds the infrastructure to register nat hooks with the nat core
instead of the netfilter core.
nat hooks are used to configure nat bindings. Such hooks are registered
from ip(6)table_nat or by the nftables core when a nat chain is added.
After next patch, nat hooks will be registered with nf_nat instead of
netfilter core. This allows to use many nat lookup functions at the
same time while doing the real packet rewrite (nat transformation) in
one place.
This change doesn't convert the intended users yet to ease review.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This will allow the nat core to reuse the nf_hook infrastructure
to maintain nat lookup functions.
The raw versions don't assume a particular hook location, the
functions get added/deleted from the hook blob that is passed to the
functions.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Will be used in followup patch when nat types no longer
use nf_register_net_hook() but will instead register with the nat core.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The ip(6)tables nat table is currently receiving skbs from the netfilter
core, after a followup patch skbs will be coming from the netfilter nat
core instead, so the table is no longer backed by normal hook_ops.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Copy-pasted, both l3 helpers almost use same code here.
Split out the common part into an 'inet' helper.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Given the fact that the ACPI "EINJ" (error injection) facility is not
universally available, implement software infrastructure to validate the
memcpy_mcsafe() exception handling implementation.
For each potential read exception point in memcpy_mcsafe(), inject a
emulated exception point at the address identified by 'mcsafe_inject'
variable. With this infrastructure implement a test to validate that the
'bytes remaining' calculation is correct for a range of various source
buffer alignments.
This code is compiled out by default. The CONFIG_MCSAFE_DEBUG
configuration symbol needs to be manually enabled by editing
Kconfig.debug. I.e. this functionality can not be accidentally enabled
by a user / distro, it's only for development.
Cc: <x86@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Use the machine check safe version of copy_to_iter() for the
->copy_to_iter() operation published by the pmem driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In preparation for protecting the dax read(2) path from media errors
with copy_to_iter_mcsafe() (via dax_copy_to_iter()), convert the
implementation to report the bytes successfully transferred.
Cc: <x86@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Similar to the ->copy_from_iter() operation, a platform may want to
deploy an architecture or device specific routine for handling reads
from a dax_device like /dev/pmemX. On x86 this routine will point to a
machine check safe version of copy_to_iter(). For now, add the plumbing
to device-mapper and the dax core.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add a common Kconfig CONFIG_ARCH_HAS_UACCESS_MCSAFE that archs can
optionally select, and fixup the declaration of _copy_to_iter_mcsafe().
Fixes: 8780356ef6 ("x86/asm/memcpy_mcsafe: Define copy_to_iter_mcsafe()")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add a test to check if a given device is a ccwgroup device.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
VMLINUX_SYMBOL() is no-op unless CONFIG_HAVE_UNDERSCORE_SYMBOL_PREFIX
is defined. It has ever been selected only by BLACKFIN and METAG.
VMLINUX_SYMBOL() is unneeded for s390-specific code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Dasd uses completion_data from struct request to store per request
private data - this is problematic since this member is part of a
union which is also used by IO schedulers.
Let the block layer maintain space for per request data behind each
struct request.
Fixes crashes on block layer timeouts like this one:
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 0000000000000000 TEID: 0000000000000483
Fault in home space mode while using kernel ASCE.
AS:0000000001308007 R3:00000000fffc8007 S:00000000fffcc000 P:000000000000013d
Oops: 0004 ilc:2 [#1] PREEMPT SMP
Modules linked in: [...]
CPU: 0 PID: 1480 Comm: kworker/0:2H Not tainted 4.17.0-rc4-00046-gaa3bcd43b5af #203
Hardware name: IBM 3906 M02 702 (LPAR)
Workqueue: kblockd blk_mq_timeout_work
Krnl PSW : 0000000067ac406b 00000000b6960308 (do_raw_spin_trylock+0x30/0x78)
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3
Krnl GPRS: 0000000000000c00 0000000000000000 0000000000000000 0000000000000001
0000000000b9d3c8 0000000000000000 0000000000000001 00000000cf9639d8
0000000000000000 0700000000000000 0000000000000000 000000000099f09e
0000000000000000 000000000076e9d0 000000006247bb08 000000006247bae0
Krnl Code: 00000000001c159c: b90400c2 lgr %r12,%r2
00000000001c15a0: a7180000 lhi %r1,0
#00000000001c15a4: 583003a4 l %r3,932
>00000000001c15a8: ba132000 cs %r1,%r3,0(%r2)
00000000001c15ac: a7180001 lhi %r1,1
00000000001c15b0: a784000b brc 8,1c15c6
00000000001c15b4: c0e5004e72aa brasl %r14,b8fb08
00000000001c15ba: 1812 lr %r1,%r2
Call Trace:
([<0700000000000000>] 0x700000000000000)
[<0000000000b9d3d2>] _raw_spin_lock_irqsave+0x7a/0xb8
[<000000000099f09e>] dasd_times_out+0x46/0x278
[<000000000076ea6e>] blk_mq_terminate_expired+0x9e/0x108
[<000000000077497a>] bt_for_each+0x102/0x130
[<0000000000774e54>] blk_mq_queue_tag_busy_iter+0x74/0xd8
[<000000000076fea0>] blk_mq_timeout_work+0x260/0x320
[<0000000000169dd4>] process_one_work+0x3bc/0x708
[<000000000016a382>] worker_thread+0x262/0x408
[<00000000001723a8>] kthread+0x160/0x178
[<0000000000b9e73a>] kernel_thread_starter+0x6/0xc
[<0000000000b9e734>] kernel_thread_starter+0x0/0xc
INFO: lockdep is turned off.
Last Breaking-Event-Address:
[<0000000000b9d3cc>] _raw_spin_lock_irqsave+0x74/0xb8
Kernel panic - not syncing: Fatal exception: panic_on_oops
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>