When moving from manual to automatic power management mode in GOYA, the
driver didn't correctly place the device in LOW power mode. As a result, if
an application was run immediately after the move, it would have run with
low frequencies.
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
If a GAUDI device is present in the system, display an error message that
it is not supported by the current kernel.
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add print upon clock slow down due to power consumption or overheating.
In addition, add print when back to optimal clock.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Sparse reports a warning at goya_hw_queues_unlock()
warning: context imbalance in goya_hw_queues_unlock() - unexpected unlock
The root cause is a missing annotation at goya_hw_queues_unlock()
Add the missing __releases(&goya->hw_queues_lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Sparse reports a warning at goya_hw_queues_lock()
warning: context imbalance in goya_hw_queues_lock() - wrong count at exit
The root cause is a missing annotation at goya_hw_queues_lock()
Add the missing __acquires(&goya->hw_queues_lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The "parse_cnt" variable is incremented while validating the CS chunks,
but it is actually not being used.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Add support for hwmon_in_highest, hwmon_temp_highest and hwmon_curr_highest
attributes. These attributes retrieve the historical maximum voltage,
temperature and current that were sampled, respectively.
Signed-off-by: Christine Gharzuzi <cgharzuzi@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The hl read and write routines implement the hwmon_ops read and write
interface routines respectively.
These routines are expected to return a completion status when called,
which was not the case until this commit.
This commit modifies these routines to return 0 upon success and a
negative error value upon failure.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This commit adds support for offsetting the temperatures reading
by a specified value as defined in
https://www.kernel.org/doc/Documentation/hwmon/sysfs-interface
using the standard sysfs defined for hwmon.
This is required by system administrators to inject errors to test
their monitoring applications in data centers.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The compute engines can perform millions of transactions per second. If
there is a bug in the S/W stack, we could get a lot of interrupts and spam
the kernel log. Therefore, ratelimit these prints
Reviewed-by: Omer Shpigelman <oshpigelman@habana.ai>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Allow debug user to write/read 64-bit data through debugfs.
This will expedite the dump process of the (large) internal
memories of the device done during debug.
Signed-off-by: Moti Haimovski <mhaimovski@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
DRAM_PHYS_BASE is already taken into account in MMU_PAGE_TABLES_ADDR.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
There is an extra ; after the end of a function, which needs to be removed
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Reviewed-by: Tomer Tayar <ttayar@habana.ai>
CS with no chunks for execute phase is invalid, so its
context_switch/restore phase should not be run.
Hence, move the check of the execute chunks number to the beginning of
hl_cs_ioctl().
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
As HL_MAX_JOBS_PER_CS is 512, it is possible that more than 255 CS jobs
will be submitted for a certain queue. Hence, modify the
"jobs_in_queue_cnt" parameter of the "hl_cs" structure to be u16 instead
of u8.
Signed-off-by: Tomer Tayar <ttayar@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Host memory may be allocated with huge pages.
A different virtual range may be used for mapping in this case.
Add Huge PCI MMU (HPMMU) properties to support it.
This patch is a prerequisite for future ASICs support and has no effect on
Goya ASIC as currently a single virtual host range is used for all page
sizes.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
When no patched command buffer (CB) is created, use the user CB size as
the job size.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This adds a callback to read the socket pid.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move cyc2ns setup logic to separate function.
This separation will allow to use cyc2ns mult/shift pair
not only for the sched_clock but also for other clocks
such as steal_clock.
Signed-off-by: Alexey Makhalov <amakhalov@vmware.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200323195707.31242-3-amakhalov@vmware.com
vmware_select_hypercall() is used only by the __init
functions, and should be annotated with __init as well.
Signed-off-by: Alexey Makhalov <amakhalov@vmware.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200323195707.31242-2-amakhalov@vmware.com
After xfrm_add_policy add a policy, its ref is 2, then
xfrm_policy_timer
read_lock
xp->walk.dead is 0
....
mod_timer()
xfrm_policy_kill
policy->walk.dead = 1
....
del_timer(&policy->timer)
xfrm_pol_put //ref is 1
xfrm_pol_put //ref is 0
xfrm_policy_destroy
call_rcu
xfrm_pol_hold //ref is 1
read_unlock
xfrm_pol_put //ref is 0
xfrm_policy_destroy
call_rcu
xfrm_policy_destroy is called twice, which may leads to
double free.
Call Trace:
RIP: 0010:refcount_warn_saturate+0x161/0x210
...
xfrm_policy_timer+0x522/0x600
call_timer_fn+0x1b3/0x5e0
? __xfrm_decode_session+0x2990/0x2990
? msleep+0xb0/0xb0
? _raw_spin_unlock_irq+0x24/0x40
? __xfrm_decode_session+0x2990/0x2990
? __xfrm_decode_session+0x2990/0x2990
run_timer_softirq+0x5c5/0x10e0
Fix this by use write_lock_bh in xfrm_policy_kill.
Fixes: ea2dea9dac ("xfrm: remove policy lock when accessing policy->walk.dead")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When there are more BP settings than needed for defining the protected
areas of the flash memory, most flashes will define the remaining
settings as "protect all", i.e. the equivalent of having all the BP bits
set to one. But there are flashes where the in-between BP values
are undefined (not mentioned), and only the "all bits set" is protecting
the entire memory. One such example is w25q80, where BP[2:0]=0b101 and
0b110 are not defined.
Set all the BP bits to one when lock_len == mtd->size, to treat this
special case.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jungseung Lee <js07.lee@samsung.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Vladimir Oltean says:
====================
PTP_CLK pin configuration for SJA1105 DSA driver
This series adds support for the PTP_CLK pin on SJA1105 to be configured
via the PTP subsystem, in the "periodic output" and "external timestamp
input" modes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The SJA1105 switch family has a PTP_CLK pin which emits a signal with
fixed 50% duty cycle, but variable frequency and programmable start time.
On the second generation (P/Q/R/S) switches, this pin supports even more
functionality. The use case described by the hardware documents talks
about synchronization via oneshot pulses: given 2 sja1105 switches,
arbitrarily designated as a master and a slave, the master emits a
single pulse on PTP_CLK, while the slave is configured to timestamp this
pulse received on its PTP_CLK pin (which must obviously be configured as
input). The difference between the timestamps then exactly becomes the
slave offset to the master.
The only trouble with the above is that the hardware is very much tied
into this use case only, and not very generic beyond that:
- When emitting a oneshot pulse, instead of being told when to emit it,
the switch just does it "now" and tells you later what time it was,
via the PTPSYNCTS register. [ Incidentally, this is the same register
that the slave uses to collect the ext_ts timestamp from, too. ]
- On the sync slave, there is no interrupt mechanism on reception of a
new extts, and no FIFO to buffer them, because in the foreseen use
case, software is in control of both the master and the slave pins,
so it "knows" when there's something to collect.
These 2 problems mean that:
- We don't support (at least yet) the quirky oneshot mode exposed by
the hardware, just normal periodic output.
- We abuse the hardware a little bit when we expose generic extts.
Because there's no interrupt mechanism, we need to poll at double the
frequency we expect to receive a pulse. Currently that means a
non-configurable "twice a second".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AVB table contains the CAS_MASTER field (to be added in the next
patch) which decides the direction of the PTP_CLK pin.
Reconfiguring this field dynamically is highly preferable to having to
reset the switch and upload a new static configuration, so we add
support for exactly that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the PTP_CLK pin starts toggling only at a time higher than the
current PTP clock, this helper from the time-aware shaper code comes in
handy here as well. We'll use it to transform generic user input for the
perout request into valid input for the sja1105 hardware.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fields configure the destination and source MAC address that the
switch will put in the Ethernet frames sent towards the CPU port that
contain RX timestamps for PTP.
These fields do not enable the feature itself, that is configured via
SEND_META0 and SEND_META1 in the General Params table.
The implication of this patch is that the AVB Params table will always
be present in the static config. Which doesn't really hurt.
This is needed because in a future patch, we will add another field from
this table, CAS_MASTER, for configuring the PTP_CLK pin function. That
can be configured irrespective of whether RX timestamping is enabled or
not, so always having this table present is going to simplify things a
bit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch found a lack of appropriate whitespace after certain keywords
as per the style guide. Add it in.
Signed-off-by: Logan Magee <mageelog@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dejin Zheng says:
====================
introduce read_poll_timeout
This patch sets is introduce read_poll_timeout macro, it is an extension
of readx_poll_timeout macro. the accessor function op just supports only
one parameter in the readx_poll_timeout macro, but this macro can
supports multiple variable parameters for it. so functions like
phy_read(struct phy_device *phydev, u32 regnum) and
phy_read_mmd(struct phy_device *phydev, int devad, u32 regnum) can
use this poll timeout framework.
the first patch introduce read_poll_timeout macro, and the second patch
redefined readx_poll_timeout macro by read_poll_timeout(), and the other
patches are examples using read_poll_timeout macro.
v6 -> v7:
- add a parameter to supports that it can sleep some time
before read operation in read_poll_timeout macro.
- add prefix with double underscores for some variable to avoid
any variable re-declaration or shadowing in patch 3 and patch
7.
v5 -> v6:
- add some check to keep the code more similar in patch 8
v4 -> v5:
- add some msleep() before call phy_read_mmd_poll_timeout() to
keep the code more similar in patch 6 and patch 9.
- add a patch of drop by v4, it can add msleep before call
phy_read_poll_timeout() to keep the code more similar.
v3 -> v4:
- add 3 examples of using new functions.
- deal with precedence issues for parameter cond.
- drop a patch about phy_poll_reset() function.
v2 -> v3:
- modify the parameter order of newly added functions.
phy_read_mmd_poll_timeout(val, cond, sleep_us, timeout_us, \
phydev, devaddr, regnum)
||
\/
phy_read_mmd_poll_timeout(phydev, devaddr regnum, val, cond, \
sleep_us, timeout_us)
phy_read_poll_timeout(val, cond, sleep_us, timeout_us, \
phydev, regnum)
||
\/
phy_read_poll_timeout(phydev, regnum, val, cond, sleep_us, \
timeout_us)
v1 -> v2:
- passed a phydev, device address and a reg to replace args...
parameter in phy_read_mmd_poll_timeout() by Andrew Lunn 's
suggestion in patch 3. Andrew Lunn <andrew@lunn.ch>, Thanks
very much for your help!
- also in patch 3, handle phy_read_mmd return an error(the return
value < 0) in phy_read_mmd_poll_timeout(). Thanks Andrew
again.
- in patch 6, pass a phydev and a reg to replace args...
parameter in phy_read_poll_timeout(), and also handle the
phy_read() function's return error.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_poll_timeout() to replace the poll codes for
simplify tja11xx_check() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_poll_timeout() to replace the poll codes for
simplify lan87xx_read_status() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_poll_timeout() to replace the poll codes for
simplify the code in phy_poll_reset() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it is sometimes necessary to poll a phy register by phy_read()
function until its value satisfies some condition. introduce
phy_read_poll_timeout() macros that do this.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify mv3310_reset() function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify aqr107_wait_reset_complete() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use phy_read_mmd_poll_timeout() to replace the poll codes for
simplify bcm84881_wait_init() function.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it is sometimes necessary to poll a phy register by phy_read_mmd()
function until its value satisfies some condition. introduce
phy_read_mmd_poll_timeout() macros that do this.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
redefined readx_poll_timeout macro by read_poll_timeout to
simplify the code.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this macro is an extension of readx_poll_timeout macro. the accessor
function op just supports only one parameter in the readx_poll_timeout
macro, but this macro can supports multiple variable parameters for
it. so functions like phy_read(struct phy_device *phydev, u32 regnum)
and phy_read_mmd(struct phy_device *phydev, int devad, u32 regnum) can
also use this poll timeout core. and also expand it can sleep some time
before read operation.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous changes to the IP routing code have removed all the
tests for the DS_HOST route flag.
Remove the flags and all the code that sets it.
Signed-off-by: David Laight <david.laight@aculab.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing Makefile for net/forwarding tests and include it to
the targets list, otherwise forwarding tests are not installed
in case of cross-compilation.
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cavium/thunder/nicvf_queues.c: In function nicvf_sq_free_used_descs:
drivers/net/ethernet/cavium/thunder/nicvf_queues.c:1182:12: warning:
variable tail set but not used [-Wunused-but-set-variable]
It's not used since commit 4863dea3fab01("net: Adding support for Cavium ThunderX network controller"),
so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng zengkai <zhengzengkai@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. A simple
reproducer would be e.g.
ip link add veth1 type veth peer name veth2
ethtool -s veth1 wol g
ip link del veth1
Make sure dev_put() is called when ethtool_ops check fails.
v2: add Fixes tags
Fixes: a53f3d41e4 ("ethtool: set link settings with LINKINFO_SET request")
Fixes: bfbcfe2032 ("ethtool: set link modes related data with LINKMODES_SET request")
Fixes: e54d04e3af ("ethtool: set message mask with DEBUG_SET request")
Fixes: 8d425b19b3 ("ethtool: set wake-on-lan settings with WOL_SET request")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a flow_dissect callback which returns the network offset and
where to find the skb protocol, given the tags structure a common
function works for both tagging formats that are supported.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When both the switch and the bridge are learning about new addresses,
switch ports attached to the bridge would see duplicate ARP frames
because both entities would attempt to send them.
Fixes: 5037d532b8 ("net: dsa: add Broadcom tag RX/TX handler")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Bug fixes.
5 bug fix patches covering an indexing bug for priority counters, memory
leak when retrieving DCB ETS settings, error path return code, proper
disabling of PCI before freeing context memory, and proper ring accounting
in error path.
Please also apply these to -stable. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If ring counts are not reset when ring reservation fails,
bnxt_init_dflt_ring_mode() will not be called again to reinitialise
IRQs when open() is called and results in system crash as napi will
also be not initialised. This patch fixes it by resetting the ring
counts.
Fixes: 47558acd56 ("bnxt_en: Reserve rings at driver open if none was reserved at probe time.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other shutdown code paths will always disable PCI first to shutdown DMA
before freeing context memory. Do the same sequence in the error path
of probe to be safe and consistent.
Fixes: c20dc142dd ("bnxt_en: Disable bus master during PCI shutdown and driver unload.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
