Add the device tree node for the Advanced Power Management Unit (APMU).
Use the "enable-method" prop to point out that the APMU should be used
for the SMP support.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We need to make sure that only proper channel slots (in SACCST register)
are enabled at playback start time since some AC'97 CODECs (like VT1613 on
UDOO board) were observed requesting via SLOTREQ spurious ones just after
an AC'97 link is started but before the CODEC is configured by its driver.
When a bit for some channel slot is set in a SLOTREQ request then SSI sets
the relevant bit in SACCST automatically, which then 'sticks' until it is
manually unset.
The SACCST register is not writable directly, we have to use SACCDIS and
SACCEN registers to configure it instead (these aren't normal registers:
writing a '1' bit at some position in SACCEN sets the relevant bit in
SACCST; SACCDIS operates in a similar way but allows unsetting bits in
SACCST).
Theoretically, this should be necessary only for the very first playback
but since some CODECs are so untrustworthy and extra channel slots enabled
mean ruined playback let's play safe here and make sure that no extra
slots are enabled in SACCST every time a playback is started.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In AC'97 mode we configure and start SSI RX / TX on probe path via
a call to _fsl_ssi_set_dai_fmt() function.
We don't need to call this function again later and in fact don't want to
do it since this function temporarily sets STCR, SRCR and SCR to some
intermediate values.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver makes the crosstalk funciton disabled by default
which can simplify the codec function. The platform may not
need this funciton and reduce the potential risk. Therefore,
We change the property "nuvoton,crosstalk-bypass" to
"nuvoton,crosstalk-enable". The crosstalk measurement is enabled
if the property is set. Otherwise, it is disabled. Besides,
add more condition in the entry point of the crosstalk sequence
to disable the function completely.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These can run on certain kernel configs. This will allow
us later to enable these tests under the right kernel
configurations.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These cannot run on all kernel builds. This will help us later
skip this test on kernel configs where non-applicable.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This cannot run on all kernel builds. This will help us later
skip this test on kernel configs where non-applicable.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Its not easy to follow the logic behind making FW_OPT_FALLBACK map
to an existing flag only if a kernel configuration option was set.
Its much easier to retpresent what was intended with function helpers
which make it clear that if CONFIG_FW_LOADER_USER_HELPER_FALLBACK is
set we force running the fallback mechanism unless a caller specifically
never wants to run it, such as request_firmware_direct().
Prior and after this change we upkeep the tradition:
CONFIG_FW_LOADER_USER_HELPER_FALLBACK
request_firmware() force fallback
request_firmware_into_buf() force fallback
request_firmware_nowait() force fallback
request_firmware_direct() always ignore fallback
!CONFIG_FW_LOADER_USER_HELPER_FALLBACK
request_firmware() ignore fallback
request_firmware_into_buf() ignore fallback
request_firmware_nowait() depends on uevent flag
request_firmware_direct() always ignore fallback
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The macro FW_OPT_USERHELPER is only currently defined when
CONFIG_FW_LOADER_USER_HELPER is set. This is handled via an
ifdef around CONFIG_FW_LOADER_USER_HELPER. This makes reading
and understanding use FW_OPT_USERHELPER a bit convoluted.
Instead wrap the functionality implemented behind
CONFIG_FW_LOADER_USER_HELPER as we typically do in the
kernel.
Now when CONFIG_FW_LOADER_USER_HELPER is *not set*, then
simply the helper fw_sysfs_fallback() will not do anything.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes it clearer that the parameters passed are only used for
the preallocated buffer option, ie, when a caller uses:
request_firmware_into_buf()
Otherwise this code won't run. We flip the logic just so the actual
prellocated buf code is not indented.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This lets us type check the callers.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Doing this makes it clearer the states are only to be used
in the context of the sysfs fallback loading interface.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will allow us to do proper typechecking on users both of
values passed and return types expected.
While at it, change the parameter passed to be the struct fw_priv,
so we can move around the state machine variable as we see fit with
these helpers.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for new chip rts5260.
In order to support rts5260, the definitions of
some internal registers and workflow have to be
modified and are different from its predecessors
and OCP function is added for RTS5260. So we need
this patch to ensure RTS5260 can work.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Tested-by: Perry Yuan <perry_yuan@dell.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
DMA handler had needed to calculate pointer before, but it doesn't
need now. Thus, we can remove unnecessary spin lock from DMAC handler.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because Realtek card reader drivers are pcie and usb drivers,
and they bridge mmc subsystem and memstick subsystem, they are
not mfd drivers. Greg and Lee Jones had a discussion about
where to put the drivers, the result is that misc is a good
place for them, so I move all files to misc. If I don't move
them to a right place, I can't add any patch for this driver.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Perry Yuan <perry_yuan@dell.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Renesas sound needs 8ch clock if TDM 6ch mode, and needs 2ch clock for
6ch or 8ch sound if Multi SSI mode. And these are related to before/after
CTU (= Channel Transfer Unit).
To calculate these we already has rsnd_runtime_channel_for_ssi() which
returns runtime necessary channels.
But, it based on runtime->channels which is not yet set when hw refine.
We need to use hw_params instead of runtime->xxx when hw refine,
and it is not needed after runtime was set.
This patch adds new hw_params on rsnd_dai_stream, and it will be removed
on rsnd_hw_params().
This is very temporary durty code, but it seems no choice at this point.
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After commit e44565f62a ("firmware: fix batched requests - wake all waiters")
where we moved away from swait to old wait with a completion we also
stopped using __fw_state_is_done(). Since this is longer used kill it.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The macro is defined twice without need.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move main core data structures used internally for firmware to the top
of the file. This will allow us to use them earlier later in helpers as
we extend their use.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes it clear exactly what the field is for. With fw_id it
was not clear to a reader if this was some sort of private concoction
of some sort.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reflects much better what this is used for. It also puts emphasis
on the fact we can and should be able to extend this data structure as
we see fit internally as its the opaque private pointer on struct
firmware.
As we rename the data structure, also rename a few functions that use it
to reflect better what they are for.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct firmware_priv is only used for the sysfs fallback
mechanism, rename it to make emphasis of this. This will also
enable us to use the name later for something much more
meaninful.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file /sys/module/firmware_class/parameters/path can be used
to set a custom firmware path. The fw_filesystem.sh script creates
a temporary directory to add a test firmware file to be used during
testing, in order for this to work it uses the custom path syfs file
and it was supposed to reset back the file on execution exit. The
script failed to do this due to a typo, it was using OLD_PATH instead
of OLD_FWPATH, since its inception since v3.17.
Its not as easy to just keep the old setting, it turns out that
resetting an empty setting won't actually do what we want, we need
to check if it was empty and set an empty space.
Without this we end up having the temporary path always set after
we run these tests.
Fixes: 0a8adf5847 ("test: add firmware_class loader test")
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
register_reboot_notifier() can fail, detect this and address this
failure. This has been broken since v3.11, however the chances of
this failing here is really low.
Fixes: fe304143b0 ("firmware: Avoid deadlock of usermodehelper lock at shutdown")
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes init / exit much easier to read, and we can later
reuse this code on other errors not captured yet.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
register_pm_notifier() can technically fail, caputure this.
Note that register_syscore_ops() cannot fail given it just
adds an element to a linked list. This has been broken since
v3.7. Chances of this failing however are slim.
To improve code readability move the code folded under CONFIG_PM_SLEEP
into a helper.
Fixes: 07646d9c09 ("firmware loader: cache devices firmware during suspend/resume cycle")
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will be used later to unfold on error on init.
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs entry "ocr" was missing the 0x prefix to identify it as hex
formatted.
Fixes: 5fb06af7a3 ("mmc: core: Extend sysfs with OCR register")
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Cc: <stable@vger.kernel.org> # v4.8+
[Ulf: Amended change to also cover SD-cards]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sysfs entry "pre_eol_info" was missing the 0x prefix to identify it
as hex formatted.
Fixes: 46bc5c408e ("mmc: core: Export device lifetime information through sysfs")
Signed-off-by: Bastian Stender <bst@pengutronix.de>
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adds support for asynchronous supplicant requests, meaning that the
supplicant can process several requests in parallel or block in a
request for some time.
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Tested-by: Etienne Carriere <etienne.carriere@linaro.org> (b2260 pager=y/n)
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Adds TEE_IOCTL_PARAM_ATTR_META which can be used to indicate meta
parameters when communicating with user space. These meta parameters can
be used by supplicant support multiple parallel requests at a time.
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
On Intel Merrifield the pin control device is a separate IP block
without any PCI ID assigned.
Though, recently we got an allocated ACPI ID for it, so, let's use fresh
ID.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
UART2 RTS is mode 2 of the pin.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The first node supplied to of_find_matching_node() has its reference
counter decreased as part of call to that function. In optee_driver_init()
after calling of_find_matching_node() it's invalid to call of_node_put() on
the supplied node again.
So remove the invalid call to of_node_put().
Reported-by: Alex Shi <alex.shi@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
If set_thread_tidr() is called twice for same task_struct then it will
allocate a new tidr value to it leaving the previous value still
dangling in the vas_thread_ida table.
To fix this the patch changes set_thread_tidr() to check if a tidr
value is already assigned to the task_struct and if yes then returns
zero.
Fixes: ec233ede4c86("powerpc: Add support for setting SPRN_TIDR")
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
[mpe: Modify to return 0 in the success case, not the TID value]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is an unsafe signed to unsigned conversion in set_thread_tidr()
that may cause an error value to be assigned to SPRN_TIDR register and
used as thread-id.
The issue happens as assign_thread_tidr() returns an int and
thread.tidr is an unsigned-long. So a negative error code returned
from assign_thread_tidr() will fail the error check and gets assigned
as tidr as a large positive value.
To fix this the patch assigns the return value of assign_thread_tidr()
to a temporary int and assigns it to thread.tidr iff its '> 0'.
The patch shouldn't impact the calling convention of set_thread_tidr()
i.e all -ve return-values are error codes and a return value of '0'
indicates success.
Fixes: ec233ede4c86("powerpc: Add support for setting SPRN_TIDR")
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Reviewed-by: Christophe Lombard clombard@linux.vnet.ibm.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are two issues after resuming from suspend on the
Audiotrak Prodigy 7.1 HiFi:
- the output volume is set to 100%
- microphone input isn't working anymore
This patch fixes these issues by reinitializing both codecs of the device
and restoring the previous volumes during resume.
Signed-off-by: Yussuf Khalil <dev@pp3345.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function "release_firmware" is called in the current implementation of
the function "_request_firmware" after a failure was detected.
Link: https://elixir.free-electrons.com/linux/v4.14-rc8/source/drivers/base/firmware_class.c#L1196
Such a call should therefore not be repeated directly after the
corresponding error information was received in the local variable "err"
of the function "snd_korg1212_create".
Thus remove a misplaced function call.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Don't populate array 'names' on the stack but instead make them static.
Makes the object code smaller by 50 bytes:
Before:
text data bss dec hex filename
21237 9192 1120 31549 7b3d linux/sound/drivers/dummy.o
After:
text data bss dec hex filename
21095 9280 1120 31495 7b07 linux/sound/drivers/dummy.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This format is similar to existing SNDRV_PCM_FORMAT_{S,U}20_3 that keep
20-bit PCM samples in 3 bytes, however i.MX6 platform SSI FIFO does not
allow 3-byte accesses (including DMA) so a 4-byte (more conventional)
format is needed for it.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Document the V3M Starter Kit device tree bindings, listing it as
a supported board.
This allows to use checkpatch.pl to validate .dts files referring to
the V3MSK board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>