In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Support was added based on Goodix GitHub repo [1]. There are two major
differences between gt1151 and currently supported devices (gt9x):
* CONFIG_DATA register has 0x8050 address instead of 0x8047,
* config data checksum has 16-bit width instead of 8-bit.
Also update goodix_i2c_test() function, so it reads ID register (which
has the same address for all devices) instead of CONFIG_DATA (because
its address is known only after reading ID of the device).
[1] https://github.com/goodix/gt1x_driver_generic
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ELAN0611 touchpad uses elan_i2c as its driver. It can be found
on Lenovo ideapad 320-15IKB.
So add it to ACPI table to enable the touchpad.
[Ido Adiv <idoad123@gmail.com> reports that the same ACPI ID is used for
Elan touchpad in ideapad 520].
BugLink: https://bugs.launchpad.net/bugs/1723736
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On CNL, individual wake rate limit was added to each engine.
GT can only go to RC6 if both Render and Media engines are
individually qualified. So we need to set their individual
wake rate limit.
+-----------------+---------------+--------------+--------------+
| | GT RC6 | Render C6 | Media C6 |
+-----------------+---------------+--------------+--------------+
| Wake rate limit | 0xA09C[31:16] | 0xA09C[15:0] | 0xA0A0[15:0] |
+-----------------+---------------+--------------+--------------+
v2: - Tune Render and Media wake rate values according to some extra
info I got from HW engineers. Value can be tuned, but for now
these are the recommended values.
- Fix typos pointed by James.
Cc: Nathan Ciobanu <nathan.d.ciobanu@intel.com>
Cc: Wayne Boyer <wayne.boyer@intel.com>
Cc: Joe Konno <joe.konno@linux.intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023224612.27208-1-rodrigo.vivi@intel.com
As we faced in BXT, on CNL DDI_A_4_LANES is not
set as expected when system is boot with multiple
monitors connected. This result in wrong lane
setup impacting the max data rate available and
consequently blocking modeset on eDP, resulting
in a blank screen.
Most of CNL SKUs don't support DDI-E.
The only SKU that supports DDI-E is the same
that supports the full A/E split called DDI-F.
Also when DDI-F is used DDI-E cannot be used because
they share Interrupts. So DDI-E is almost useless.
Anyways let's consider this is possible and rely on
VBT for that.
This patch was initialy start by Clint, but required
many changes including full commit message. So
Credits entirely to Clint for finding this.
v2: Extract all messy conditions into a helper function
as suggested by Ville.
Along with simplification I removed the debug
message on the working case since now all conditions
are grouped.
v3: Split the conditions even more as suggested by Ville.
Get's cleaner and easier to add new cases in the
future.
Suggested-by: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023173920.22890-1-rodrigo.vivi@intel.com
We've been missing a goto to the unwind path...
Acked-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add missing counter decrement to prevent out of bounds memory read.
Signed-off-by: Eric Sesterhenn <eric.sesterhenn@x41-dsec.de>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Only stored, never read. This is a leftover from commit 7d08487777
("netfilter: connlimit: use rbtree for per-host conntrack obj storage"),
which added the rbtree node struct that stores the address instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
after previous commit xt_replace_table will wait until all cpus
had even seqcount (i.e., no cpu is accessing old ruleset).
Add a 'old' counter retrival version that doesn't synchronize counters.
Its not needed, the old counters are not in use anymore at this point.
This speeds up table replacement on busy systems with large tables
(and many cores).
Cc: Dan Williams <dcbw@redhat.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
xt_replace_table relies on table replacement counter retrieval (which
uses xt_recseq to synchronize pcpu counters).
This is fine, however with large rule set get_counters() can take
a very long time -- it needs to synchronize all counters because
it has to assume concurrent modifications can occur.
Make xt_replace_table synchronize by itself by waiting until all cpus
had an even seqcount.
This allows a followup patch to copy the counters of the old ruleset
without any synchonization after xt_replace_table has completed.
Cc: Dan Williams <dcbw@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We currently pass down the l4 protocol to the conntrack ->packet()
function, but the only user of this is the debug info decision.
Same information can be derived from struct nf_conn.
Add a wrapper for the previous patch that extracs the information
from nf_conn and passes it to nf_l4proto_log_invalid().
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We currently pass down the l4 protocol to the conntrack ->packet()
function, but the only user of this is the debug info decision.
Same information can be derived from struct nf_conn.
As a first step, add and use a new log function for this, similar to
nf_ct_helper_log().
Add __cold annotation -- invalid packets should be infrequent so
gcc can consider all call paths that lead to such a function as
unlikely.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We can use a single statement for this.
While at it, fixup the comment -- we don't have pernet table/ops
anymore, the function is only called from module exit path.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The compat callback was missing and triggered failures in 32bits
userspace when enabling/disable the perf stream. We don't require any
particular processing here as these ioctls don't take any argument.
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: eec688e142 ("drm/i915: Add i915 perf infrastructure")
Cc: linux-stable <stable@vger.kernel.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024152728.4873-1-lionel.g.landwerlin@intel.com
__memcpy_{to,from}io fall back to byte-at-a-time copying if both the
source and destination pointers are not 8-byte aligned. Since one of the
pointers always points at normal memory, this is unnecessary and
detrimental to performance, so only do byte copying until we hit an 8-byte
boundary for the device pointer.
This change was motivated by performance issues in the pstore driver.
On a test platform, measuring probe time for pstore, console buffer
size of 1/4MB and pmsg of 1/2MB, was in the 90-107ms region. Change
managed to reduce it to 10-25ms, an improvement in boot time.
Cc: Kees Cook <keescook@chromium.org>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Mark Salyzyn <salyzyn@android.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This change will fix an issue with dma_free size found with
DMA API debug enabled.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.13 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of relying on a mix of runtime PM and the s_power() callback, drop
the s_power() callback altogether and use runtime PM solely.
As device access is required during device power-on and power-off
sequences, runtime PM alone cannot tell whether the device is available.
Thus the "active" field is introduced in struct smiapp_sensor to tell
whether it is safe to write to the device.
Consequently there is no need to power on the device whenever a file
handle is open. This functionality is removed as well. The user may still
control the device power management through sysfs. Autosuspend remains
enabled, with 1 s delay.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use unlocked __v4l2_ctrl_handler_setup() in order to make the
control setup atomic.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Merge in ARM PMU and perf updates for 4.15:
- Support for the Statistical Profiling Extension
- Support for Hisilicon's SoC PMU
Signed-off-by: Will Deacon <will.deacon@arm.com>
arm_pmu interrupts are maked as PERCPU even when these are not local
physical interrupts to a single CPU. When using non-local interrupts,
interrupts marked as PERCPU will not get freed not disabled properly
by the PMU driver.
Check if interrupts are local to a single CPU with PERCPU_DEVID since
this is what the PMU driver really needs to know.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
irq_is_percpu indicates whether an irq should only target a single cpu.
PERCPU_DEVID flag indicates that an irq can be configured differently on
each cpu it can target.
Provide a function to check whether an irq is PERCPU_DEVID.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Originally we set the priority to max upon inserting the request into
the execlists queue (and removing it from the scheduler lists). We could
then use the prio==INT_MAX as a shortcut within execlists_schedule() to
detect the end of the dependency chain. Since commit 1f181225f8
("drm/i915/execlists: Keep request->priority for its lifetime") this is
no longer true as we use the request completion as an indicator the
schedule dependency chain is complete instead. (This allows us to then
reschedule requests even when its context is in flight.) However, this
makes the GEM_BUG_ON() inside execlists_schedule() racy as we may change
the rq->prio at the same time. As the assertion is useful, let's keep
the assertion and remove the micro-optimisation.
Fixes: 1f181225f8 ("drm/i915/execlists: Keep request->priority for its lifetime")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024115501.21033-1-chris@chris-wilson.co.uk
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Back in commit a4b2b01523 ("drm/i915: Don't mark an execlists
context-switch when idle") we noticed the presence of late
context-switch interrupts. We were able to filter those out by looking
at whether the ELSP remained active, but in commit beecec9017
("drm/i915/execlists: Preemption!") that became problematic as we now
anticipate receiving a context-switch event for preemption while ELSP
may be empty. To restore the spurious interrupt suppression, add a
counter for the expected number of pending context-switches and skip if
we do not need to handle this interrupt to make forward progress.
v2: Don't forget to switch on for preempt.
v3: Reduce the counter to a on/off boolean tracker. Declare the HW as
active when we first submit, and idle after the final completion event
(with which we confirm the HW says it is idle), and track each source
of activity separately. With a finite number of sources, it should aide
us in debugging which gets stuck.
Fixes: beecec9017 ("drm/i915/execlists: Preemption!")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023213237.26536-3-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
When we park the engine (upon idling), we kill the irq tasklet. However,
to be sure that it is not restarted by a spurious interrupt after doing so,
flush the interrupt handler before parking. As we only park the engines
when we believe the system is idle, there should not be any interrupts to
distrub us; so flushing the final in-flight interrupt should be sufficient.
(However, we are still dependent on the HW behaving in an orderly and
timely fashion, which we shall endeavour to improve upon later.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023213237.26536-2-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
In the idle worker we drop the prolonged GT wakeref used to cover such
essentials as interrupt delivery. (When a CS interrupt arrives, we also
assert that the GT is awake.) However, it turns out that 10ms is not
long enough to be assured that the last CS interrupt has been delivered,
so bump that to 200ms, and move the entirety of that wait to before we
take the struct_mutex to avoid blocking. As this is now a potentially
long wait, restore the earlier behaviour of bailing out early when a new
request arrives.
v2: Break out the repeated check for new requests into its own little
helper to try and improve the self-commentary.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023213237.26536-1-chris@chris-wilson.co.uk
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds the DMA controller driver for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds the binding documentation for Spreadtrum SC9860 DMA
controller device.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
With index=on, ovl_indexdir_cleanup() tries to cleanup invalid index
entries (e.g. bad index name). This behavior could result in cleaning of
entries created by newer kernels and is therefore undesirable.
Instead, abort mount if such entries are encountered. We still cleanup
'stale' entries and 'orphan' entries, both those cases can be a result
of offline changes to lower and upper dirs.
When encoutering an index entry of type directory or whiteout, kernel
was supposed to fallback to read-only mount, but the fill_super()
operation returns EROFS in this case instead of returning success with
read-only mount flag, so mount fails when encoutering directory or
whiteout index entries. Bless this behavior by returning -EINVAL on
directory and whiteout index entries as we do for all unsupported index
entries.
Fixes: 61b674710c ("ovl: do not cleanup directory and whiteout index..")
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Treat ENOENT from index entry lookup the same way as treating a returned
negative dentry. Apparently, either could be returned if file is not
found, depending on the underlying file system.
Fixes: 359f392ca5 ("ovl: lookup index entry for copy up origin")
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Commit fbaf94ee3c ("ovl: don't set origin on broken lower hardlink")
attempt to avoid the condition of non-indexed upper inode with lower
hardlink as origin. If this condition is found, lookup returns EIO.
The protection of commit mentioned above does not cover the case of lower
that is not a hardlink when it is copied up (with either index=off/on)
and then lower is hardlinked while overlay is offline.
Changes to lower layer while overlayfs is offline should not result in
unexpected behavior, so a permanent EIO error after creating a link in
lower layer should not be considered as correct behavior.
This fix replaces EIO error with success in cases where upper has origin
but no index is found, or index is found that does not match upper
inode. In those cases, lookup will not fail and the returned overlay inode
will be hashed by upper inode instead of by lower origin inode.
Fixes: 359f392ca5 ("ovl: lookup index entry for copy up origin")
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
A previous patch inadvertently left an unused test function in the
header, kill it.
Fixes: 8bd400204b ("lightnvm: pblk: cleanup unused and static functions")
Signed-off-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This adds the definition for eFuse that is found on RK3368 SoCs with the
corresponding data cells.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The special value of 0 for device resume latency PM QoS means
"no restriction", but there are two problems with that.
First, device resume latency PM QoS requests with 0 as the
value are always put in front of requests with positive
values in the priority lists used internally by the PM QoS
framework, causing 0 to be chosen as an effective constraint
value. However, that 0 is then interpreted as "no restriction"
effectively overriding the other requests with specific
restrictions which is incorrect.
Second, the users of device resume latency PM QoS have no
way to specify that *any* resume latency at all should be
avoided, which is an artificial limitation in general.
To address these issues, modify device resume latency PM QoS to
use S32_MAX as the "no constraint" value and 0 as the "no
latency at all" one and rework its users (the cpuidle menu
governor, the genpd QoS governor and the runtime PM framework)
to follow these changes.
Also add a special "n/a" value to the corresponding user space I/F
to allow user space to indicate that it cannot accept any resume
latencies at all for the given device.
Fixes: 85dc0b8a40 (PM / QoS: Make it possible to expose PM QoS latency constraints)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197323
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alex Shi <alex.shi@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Commit 3d8f7a89a1 ("hwmon: (tmp102) Improve handling of initial read
delay") reduced the initial temperature read delay and made it dependent
on the chip's shutdown mode. If the chip was not in shutdown mode at probe,
the read delay no longer applies.
This ignores the fact that the chip initialization changes the temperature
sensor resolution, and that the temperature register values change when
the resolution is changed. As a result, the reported temperature is twice
as high as the real temperature until the first temperature conversion
after the configuration change is complete. This can result in unexpected
behavior and, worst case, in a system shutdown. To fix the problem,
let's just always wait for a conversion to complete before reporting
a temperature.
Fixes: 3d8f7a89a1 ("hwmon: (tmp102) Improve handling of initial read delay")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197167
Reported-by: Ralf Goebel <ralf.goebel@imago-technologies.com>
Cc: Ralf Goebel <ralf.goebel@imago-technologies.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The fake symbols we create for inlined frames will represent different
functions but can use the symbol start address. This leads to issues
when different inline branches all lead to the same function.
Before:
~~~~~
$ perf report -s sym -i perf.inlining.data --inline --stdio -g function
...
--38.86%--_start
__libc_start_main
main
|
--37.57%--std::norm<double> (inlined)
std::_Norm_helper<true>::_S_do_it<double> (inlined)
|
--36.36%--std::abs<double> (inlined)
std::__complex_abs (inlined)
|
--12.24%--std::linear_congruential_engine<unsigned long, 16807ul, 0ul, 2147483647ul>::operator() (inlined)
std::__detail::__mod<unsigned long, 2147483647ul, 16807ul, 0ul> (inlined)
std::__detail::_Mod<unsigned long, 2147483647ul, 16807ul, 0ul, true, true>::__calc (inlined)
~~~~~
Note that this backtrace representation is completely bogus.
Complex abs does not call the linear congruential engine! It
is just a side-effect of a longer inlined stack being appended
to a shorter, different inlined stack, both of which originate
in the same function (main).
This patch fixes the issue:
~~~~~
$ perf report -s sym -i perf.inlining.data --inline --stdio -g function
...
--38.86%--_start
__libc_start_main
main
|
|--35.59%--std::uniform_real_distribution<double>::operator()<std::linear_congruential_engine<unsigned long, 16807ul, 0ul, 2147483647ul> > (inlined)
| std::uniform_real_distribution<double>::operator()<std::linear_congruential_engine<unsigned long, 16807ul, 0ul, 2147483647ul> > (inlined)
| |
| --34.37%--std::__detail::_Adaptor<std::linear_congruential_engine<unsigned long, 16807ul, 0ul, 2147483647ul>, double>::operator() (inlined)
| std::generate_canonical<double, 53ul, std::linear_congruential_engine<unsigned long, 16807ul, 0ul, 2147483647ul> > (inlined)
| |
| --12.24%--std::linear_congruential_engine<unsigned long, 16807ul, 0ul, 2147483647ul>::operator() (inlined)
| std::__detail::__mod<unsigned long, 2147483647ul, 16807ul, 0ul> (inlined)
| std::__detail::_Mod<unsigned long, 2147483647ul, 16807ul, 0ul, true, true>::__calc (inlined)
|
--1.99%--std::norm<double> (inlined)
std::_Norm_helper<true>::_S_do_it<double> (inlined)
std::abs<double> (inlined)
std::__complex_abs (inlined)
~~~~~
Signed-off-by: Milian Wolff <milian.wolff@kdab.com>
Reviewed-by: Jiri Olsa <jolsa@redhat.com>
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Yao Jin <yao.jin@linux.intel.com>
Link: http://lkml.kernel.org/r/20171009203310.17362-10-milian.wolff@kdab.com
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
[ Fix up conflict with c1fbc0cf81 ("perf callchain: Compare dsos (as well) for CCKEY_FUNCTION"), remove unneeded hunk ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The original patch that introduced inline frame output in the various
browsers used this suffix already. The new centralized approach that
uses fake symbols for inlined frames was missing this approach so far.
Instead of changing the symbol name itself, we only print the suffix
where needed. This allows us to efficiently lookup the symbol for a
given name without first having to append the suffix before the lookup.
Signed-off-by: Milian Wolff <milian.wolff@kdab.com>
Reviewed-by: Jiri Olsa <jolsa@redhat.com>
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Yao Jin <yao.jin@linux.intel.com>
Link: http://lkml.kernel.org/r/20171009203310.17362-8-milian.wolff@kdab.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When a callchain entry has no srcline available, we ended up comparing
the instruction pointer. I consider this to be not too useful. Rather, I
think we should group the entries by function name, which this patch
adds. For people who want to split the data on the IP boundary, using
`-g address` is the correct choice.
Before:
~~~~~
100.00% 38.86% [.] main
|
|--61.14%--main inlining.cpp:14
| std::norm<double> complex:664
| std::_Norm_helper<true>::_S_do_it<double> complex:654
| std::abs<double> complex:597
| std::__complex_abs complex:589
| |
| |--56.03%--hypot
| | |
| | |--8.45%--__hypot_finite
| | |
| | |--7.62%--__hypot_finite
| | |
| | |--2.29%--__hypot_finite
| | |
| | |--2.24%--__hypot_finite
| | |
| | |--2.06%--__hypot_finite
| | |
| | |--1.81%--__hypot_finite
...
~~~~~
After:
~~~~~
100.00% 38.86% [.] main
|
|--61.14%--main inlining.cpp:14
| std::norm<double> complex:664
| std::_Norm_helper<true>::_S_do_it<double> complex:654
| std::abs<double> complex:597
| std::__complex_abs complex:589
| |
| |--60.29%--hypot
| | |
| | --56.03%--__hypot_finite
| |
| --0.85%--cabs
~~~~~
Signed-off-by: Milian Wolff <milian.wolff@kdab.com>
Reviewed-by: Jiri Olsa <jolsa@redhat.com>
Reviewed-by: Namhyung Kim <namhyung@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Yao Jin <yao.jin@linux.intel.com>
Link: http://lkml.kernel.org/r/20171009203310.17362-7-milian.wolff@kdab.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>