The following build warning is seen with W=1:
warning: no previous prototype for ‘imx5_cpuidle_init’
[-Wmissing-prototypes] int __init imx5_cpuidle_init(void)
Fix this warning by including "cpuidle.h".
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following build warning is seen with W=1:
warning: no previous prototype for ‘mxc_expio_init’
[-Wmissing-prototypes] int __init mxc_expio_init(u32 base, u32 intr_gpio)
Fix this warning by including "3ds_debugboard.h".
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following build warnings are seen with W=1:
warning: no previous prototype for ‘mx31moboard_devboard_init’
[-Wmissing-prototypes] void __init mx31moboard_devboard_init(void)
warning: no previous prototype for ‘mx31moboard_marxbot_init’
[-Wmissing-prototypes] void __init mx31moboard_marxbot_init(void)
Fix these warnings by including "board-mx31moboard.h".
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
More 4.15 drm-misc stuff:
Cross-subsystem Changes:
- bridge cleanup refactor (Benjamin Gaignard)
Core Changes:
- less surprising atomic iterators (Maarten), fixes an oops introduced
in drm-next
- better gem/fb helper docs (Noralf)
- fix dma-buf rcu races (Christian König)
Driver Changes:
- adv7511: CEC support (Hans Verkuil)
- sun4i update from Chen-Yu to improve hdmi and A31 support
- sii8620: add remote control support (Maceiej Purski)
New drivers:
- SiI9234 bridge driver (Maciej Purski)
- 7" rpi touch panel (Eric Anholt)
Note that this contains a topic pull from regmap, needed by the sun4i
changes. Mark Brown sent that out for pulling into drm-misc.
* tag 'drm-misc-next-2017-10-12' of git://anongit.freedesktop.org/drm/drm-misc: (29 commits)
drm/dp: WARN about invalid/unknown link rates and bw codes
drm/msm/mdp5: remove less than 0 comparison for unsigned value
drm/bridge/sii8620: add remote control support
drm/sun4i: hdmi: Add support for A31's HDMI controller
drm/sun4i: hdmi: Add A31 specific DDC register definitions
drm/sun4i: hdmi: Add support for controller hardware variants
dt-bindings: display: sun4i: Add binding for A31 HDMI controller
drm/sun4i: hdmi: Allow using second PLL as TMDS clk parent
drm/sun4i: hdmi: create a regmap for later use
drm/sun4i: hdmi: Disable clks in bind function error path and unbind function
drm/sun4i: tcon: Add support for demuxing TCON output on A31
drm/sun4i: tcon: Add variant callback for TCON output muxing
drm/bridge/synopsys: dsi :remove is_panel_bridge
drm/vc4: remove bridge from driver internal structure
drm/stm: ltdc: remove bridge from driver internal structure
drm/drm_of: add drm_of_panel_bridge_remove function
drm/bridge: make drm_panel_bridge_remove more robust
dma-fence: fix dma_fence_get_rcu_safe v2
dma-buf: make reservation_object_copy_fences rcu save
drm/atomic: Unref duplicated drm_atomic_state in drm_atomic_helper_resume()
...
The module clock is used for two purposes:
- Wake-on-LAN (WoL), which is optional,
- gPTP Timer Increment (GTI) configuration, which is mandatory.
As the clock is needed for GTI configuration anyway, WoL is always
available. Hence remove duplication and repeated obtaining of the clock
by making GTI use the stored clock for WoL use.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafał Miłecki says:
====================
net: support bgmac with B50212E B1 PHY
I got a report that a board with BCM47189 SoC and B50212E B1 PHY doesn't
work well some devices as there is massive ping loss. After analyzing
PHY state it has appeared that is runs in slave mode and doesn't auto
switch to master properly when needed.
This patchset fixes this by:
1) Adding new flag support to the PHY driver for setting master mode
2) Modifying bgmac to request master mode for reported hardware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 4 very similar PHYs:
0x600d84a1: BCM54210E (rev B0)
0x600d84a2: BCM54210E (rev B1)
0x600d84a5: B50212E (rev B0)
0x600d84a6: B50212E (rev B1)
that need setting master mode manually. It's because they run in slave
mode by default with Automatic Slave/Master configuration disabled which
can lead to unreliable connection with massive ping loss.
So far it was reported for a board with BCM47189 SoC and B50212E B1 PHY
connected to the bgmac supported ethernet device. Telling PHY driver to
setup PHY properly solves this issue.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of Broadcom's PHYs run by default in slave mode with Automatic
Slave/Master configuration disabled. It stops them from working properly
with some devices.
So far it has been verified for BCM54210E and BCM50212E which don't
work well with Intel's I217-LM and I218-LM:
http://ark.intel.com/products/60019/Intel-Ethernet-Connection-I217-LMhttp://ark.intel.com/products/71307/Intel-Ethernet-Connection-I218-LM
I was told there is massive ping loss.
This commit adds support for a new flag which can be set by an ethernet
driver to fixup PHY setup.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel config help for policy routing was still pointing at
an ancient document from 2000 that refers to Linux 2.1. Update it
to point to something that is at least occasionally updated.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the underlying master ever changes its L2 (e.g. bonding device),
then make sure that the IPvlan slaves always emit packets with the
current L2 of the master instead of the stale mac addr which was
copied during the device creation. The problem can be seen with
following script -
#!/bin/bash
# Create a vEth pair
ip link add dev veth0 type veth peer name veth1
ip link set veth0 up
ip link set veth1 up
ip link show veth0
ip link show veth1
# Create an IPvlan device on one end of this vEth pair.
ip link add link veth0 dev ipvl0 type ipvlan mode l2
ip link show ipvl0
# Change the mac-address of the vEth master.
ip link set veth0 address 02:11:22:33:44:55
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit:
d1898b7336 ("x86/fpu: Add tracepoints to dump FPU state at key points")
... added the 'x86_fpu_state' and 'x86_fpu_deactivate_state' trace points,
but never used them. Today they are still not used. As they take up
and waste memory, remove them.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20171012180619.670b68b6@gandalf.local.home
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Alexander Aring says:
====================
sched: act: ife: UAPI checks and performance tweaks
this patch series contains at first a patch which adds a check for
IFE_ENCODE and IFE_DECODE when a ife act gets created or updated and adding
handling of these cases only inside the act callback only.
The second patch use per-cpu counters and move the spinlock around so that
the spinlock is less being held in act callback.
The last patch use rcu for update parameters and also move the spinlock for
the same purpose as in patch 2.
Notes:
- There is still a spinlock around for protecting the metalist and a
rw-lock for another list. Should be migrated to a rcu list, ife
possible.
- I use still dereference in dump callback, so I think what I didn't
got was what happened when rcu_assign_pointer will do when rcu read
lock is held. I suppose the pointer will be updated, then we don't
have any issue here.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the parameter updating via RCU and not protected by a
spinlock anymore. This reduce the time that the spinlock is being held.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch migrates the current counter handling which is protected by a
spinlock to a per-cpu counter handling. This reduce the time where the
spinlock is being held.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the check of the two possible ife handlings encode
and decode to the init callback. The decode value is for usability
aspect and used in userspace code only. The current code offers encode
else decode only. This patch avoids any other option than this.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roman Mashak says:
====================
net: sched: Fix IFE meta modules loading
Adjust module alias names of IFE meta modules and fix the bug that
prevented auto-loading IFE modules in run-time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro __stringify_1() can stringify a macro argument, however IFE_META_*
are enums, so they never expand, however request_module expects an integer
in IFE module name, so as a result it always fails to auto-load.
Fixes: ef6980b6be ("introduce IFE action")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make style of module alias name consistent with other subsystems in kernel,
for example net devices.
Fixes: 084e2f6566 ("Support to encoding decoding skb mark on IFE action")
Fixes: 200e10f469 ("Support to encoding decoding skb prio on IFE action")
Fixes: 408fbc22ef ("net sched ife action: Introduce skb tcindex metadata encap decap")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following build warnings are seen with W=1:
Warning (simple_bus_reg): Node /soc/sram@00900000 simple-bus unit
address format error, expected "900000"
Warning (simple_bus_reg): Node /soc/aips-bus@02000000 simple-bus unit
address format error, expected "2000000"
Warning (simple_bus_reg): Node /soc/aips-bus@02000000/pxp@020f0000
simple-bus unit address format error, expected "20f0000"
(...)
Remove the leading zeroes from unit addresses to fix the warnings.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following build warnings are seen with W=1:
Warning (unit_address_format): Node /interrupt-controller@00a01000 unit
name should not have leading 0s
Warning (simple_bus_reg): Node /soc/sram@00900000 simple-bus unit address
format error, expected "900000"
Warning (simple_bus_reg): Node /soc/dma-apbh@01804000 simple-bus unit
address format error, expected "1804000"
(...)
Remove the leading zeroes from unit addresses to fix the warnings.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On the Utilite Pro the CEC line is wired up to the HDMI connector.
Add the required pinctrl setting.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Select CONFIG_DRM_DW_HDMI_CEC option, so that the CEC driver can be
loaded by default.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
HDMI_TX_CEC_LINE pin is used for CEC, so pass it in the device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit c26ebe98a1 ("PCI: imx6: Add regulator support"), it is
possible to pass the 'vpcie-supply' property to describe the PCIE supply.
This way we can remove the 'regulator-always-on' property from the
regulator and have a better device tree description.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for can1 and can2 nodes on Engicam i.CoreM6 RQS
QDL module boards.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
max11801 touchscreen on Engicam iCoreM6 DualLite/Solo module is
connected via i2c1, so add max11801: touchscreen@48 on i2c1.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch replace fsl,imx-audio-sgtl5000 and use simple-audio-card
for Engicam i.CoreM6 RQS QDL platform boards.
This patch also fix, pinctrl_adumux.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6q, imx6dl icore-rqs modules share common sound nodes,
so move the sound nodes from imx6q-icore-rqs into dtsi so-that
both can share the common node details.
And also replace codec: sgtl5000@0a => sgtl5000: codec@a
on imx6q-icore-rqs.dts to [label:] node-name[@unit-address]
according to devicetree specification from ePAPER v1.1
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Linux Sound card now uses generic simple-audio-card, so add
the same along with related audmux and codec(via u2c3) for
i.CoreM6 QDL module boards.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The new driver fails to build when CONFIG_PINCTRL is disabled:
drivers/gpu/drm/rockchip/rockchip_lvds.c: In function 'rockchip_lvds_grf_config':
drivers/gpu/drm/rockchip/rockchip_lvds.c:229:39: error: dereferencing pointer to incomplete type 'struct dev_pin_info'
if (lvds->pins && !IS_ERR(lvds->pins->default_state))
This adds the respective Kconfig dependency.
Fixes: 34cc0aa254 ("drm/rockchip: Add support for Rockchip Soc LVDS")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171005120957.485433-1-arnd@arndb.de
Return proper error instead of 0 if the revision does not match.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Fix a device properties management issue, introduced during the
4.9 cycle, that causes device properties associated with a
parent device to go away on a removal of its child in some
cases (Jarkko Nikula).
- Fix inconsistencies in error codes returned by a new function
helper in the device properties framework depending on the
underlying low-level firmware interface, DT or ACPI, by making the
meaning of error codes returned in the ACPI case agree with the
meaning of DT error codes in analogous situations (Sakari Ailus).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=gO65
-----END PGP SIGNATURE-----
Merge tag 'devprop-4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework fixes from Rafael Wysocki:
"These fix an issue related to device removal introduced during the 4.9
cycle and fix up new functionality added recently.
Specifics:
- Fix a device properties management issue, introduced during the 4.9
cycle, that causes device properties associated with a parent
device to go away on a removal of its child in some cases (Jarkko
Nikula).
- Fix inconsistencies in error codes returned by a new function
helper in the device properties framework depending on the
underlying low-level firmware interface, DT or ACPI, by making the
meaning of error codes returned in the ACPI case agree with the
meaning of DT error codes in analogous situations (Sakari Ailus)"
* tag 'devprop-4.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: properties: Fix __acpi_node_get_property_reference() return codes
ACPI: properties: Align return codes of __acpi_node_get_property_reference()
device property: Track owner device of device property
There is a risk of overflowing vblank timestamps in 2038 or 2106 if
someone sets the drm_timestamp_monotonic module parameter to zero.
I found no indication of anyone ever setting the parameter, or
complaining about the default being wrong, after it was introduced
as a way to handle backwards-compatibility with linux prior to
c61eef726a ("drm: add support for monotonic vblank timestamps"),
so it's probably safer to just remove the parameter completely
and only allowing the default behavior.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The drm vblank handling uses 'timeval' to store timestamps in either
monotonic or wall-clock time base. In either case, it reads the current
time as a ktime_t in get_drm_timestamp() and converts it from there.
This is a bit suspicious, as users of 'timeval' often suffer from
the time_t overflow in y2038. I have gone through this code and
found that it is unlikely to cause problems here:
- The user space ABI does not use time_t or timeval, but uses
'u32' and 'long' as the types. This means at least that rebuilding
user programs against a new libc with 64-bit time_t does not
change the ABI.
- As of commit c61eef726a ("drm: add support for monotonic vblank
timestamps") in linux-3.8, the monotonic timestamp is the default
and can only get reverted to wall-clock through a module-parameter.
- With the default monotonic timestamps, there is no problem at all.
- The drm_wait_vblank_ioctl() interface is alway safe on 64-bit
architectures, on 32-bit it might overflow the 'long' timestamps
in 2038 with wall-clock timestamps.
- The event handling uses 'u32' seconds, which overflow in 2106
on both 32-bit and 64-bit machines, when wall-clock timestamps
are used.
- The effect of overflowing either of the two is only temporary
(during the overflow, and is likely to keep working again
afterwards. It is likely the same problem as observing a
'settimeofday()' call, which was the reason for moving to the
monotonic timestamps in the first place.
Overall, this seems good enough, so my patch removes the use of
'timeval' from the vblank handling altogether and uses ktime_t
consistently, except for the part where we copy the data to user
space structures in the existing format.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of adding a binary sysfs attribute from the driver (which suffers
from a race condition as the attribute appears after the device), use the
core to register an nvmem device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Disabling interrupts when removing the driver is bad practice as this will
prevent some platform from waking up when using that RTC.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There is a race condition that can happen if abx80x_probe() fails after the
rtc registration succeeded. Solve that by moving the registration at the
end of the probe function.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Instead of adding a binary sysfs attribute from the driver (which suffers
from a race condition as the attribute appears after the device), use the
core to register an nvmem device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Instead of adding a binary sysfs attribute from the driver (which suffers
from a race condition as the attribute appears after the device), use the
core to register an nvmem device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
- Fix a stale kernel memory exposure when logging inodes.
- Fix some build problems with CONFIG_XFS_RT=n
- Don't change inode mode if the acl write fails, leaving the file totally
inaccessible.
- Fix a dangling pointer problem when removing an attr fork under memory
pressure.
- Don't crash while trying to invalidate a null buffer associated with a
corrupt metadata pointer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6Yvh
-----END PGP SIGNATURE-----
Merge tag 'xfs-4.14-fixes-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- Fix a stale kernel memory exposure when logging inodes.
- Fix some build problems with CONFIG_XFS_RT=n
- Don't change inode mode if the acl write fails, leaving the file
totally inaccessible.
- Fix a dangling pointer problem when removing an attr fork under
memory pressure.
- Don't crash while trying to invalidate a null buffer associated with
a corrupt metadata pointer.
* tag 'xfs-4.14-fixes-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: handle error if xfs_btree_get_bufs fails
xfs: reinit btree pointer on attr tree inactivation walk
xfs: Fix bool initialization/comparison
xfs: don't change inode mode if ACL update fails
xfs: move more RT specific code under CONFIG_XFS_RT
xfs: Don't log uninitialised fields in inode structures
A bug recently encountered involved the issue where are we were
submitting requests to different ppGTT, each would pin a segment of the
GGTT for its logical context and ring. However, this is invisible to
eviction as we do not tie the context/ring VMA to a request and so do
not automatically wait upon it them (instead they are marked as pinned,
preventing eviction entirely). Instead the eviction code must flush those
contexts by switching to the kernel context. This selftest tries to
fill the GGTT with contexts to exercise a path where the
switch-to-kernel-context failed to make forward progress and we fail
with ENOSPC.
v2: Make the hole in the filled GGTT explicit.
v3: Swap out the arbitrary timeout for a private notification from
i915_gem_evict_something()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171012125726.14736-3-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
For some selftests, we want to issue requests but delay them going to
hardware. Furthermore, we don't want those requests to block
indefinitely (or else we may hang the driver and block testing) so we
want to employ a timeout. So naturally we want a fence that is
automatically signaled by a timer.
v2: Add kselftests.
v3: Limit the API available to selftests; there isn't an overwhelming
reason to export it universally.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171012125726.14736-2-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
In the full-ppgtt world, we can fill the GGTT full of context objects.
These context objects are currently implicitly tracked by the requests
that pin them i.e. they are only unpinned when the request is completed
and retired, but we do not have the link from the vma to the request
(anymore). In order to unpin those contexts, we have to issue another
request and wait upon the switch to the kernel context.
The bug during eviction was that we assumed that a full GGTT meant we
would have requests on the GGTT timeline, and so we missed situations
where those requests where merely in flight (and when even they have not
yet been submitted to hw yet). The fix employed here is to change the
already-is-idle test to no look at the execution timeline, but count the
outstanding requests and then check that we have switched to the kernel
context. Erring on the side of overkill here just means that we stall a
little longer than may be strictly required, but we only expect to hit
this path in extreme corner cases where returning an erroneous error is
worse than the delay.
v2: Logical inversion when swapping over branches.
Fixes: 80b204bce8 ("drm/i915: Enable multiple timelines")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171012125726.14736-1-chris@chris-wilson.co.uk