Commit graph

932,869 commits

Author SHA1 Message Date
Vladimir Barinov
4339306ace arm64: dts: ulcb-kf: hog USB3 hub control gpios
This adds gpio hogs for USB3 hub on ULCB Kingfisher board to power up and
remove from reset the hub

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:26 +02:00
Vladimir Barinov
6d5fcdd39f arm64: dts: ulcb-kf: enable PCA9548 on I2C4
This supports PCA9548 I2C switch on I2C4 bus on ULCB Kingfisher board

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:25 +02:00
Vladimir Barinov
c6f9cbe364 arm64: dts: ulcb-kf: enable PCA9548 on I2C2
This supports PCA9548 I2C switch on I2C2 bus on ULCB Kingfisher board

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:24 +02:00
Vladimir Barinov
0f9c47b244 arm64: dts: ulcb-kf: enable TCA9539 on I2C4
This supports TCA9539 gpio expanders on I2C4 bus on ULCB Kingfisher board

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:23 +02:00
Vladimir Barinov
1189d1d4e3 arm64: dts: ulcb-kf: enable TCA9539 on I2C2
This supports TCA9539 gpio expanders on I2C2 bus on ULCB Kingfisher board

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:23 +02:00
Vladimir Barinov
af75811605 arm64: dts: ulcb-kf: enable USB3.0 Host
This supports USB3.0 Host on ULCB Kingfisher board

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:22 +02:00
Vladimir Barinov
e0304a365b arm64: dts: ulcb-kf: enable PCIE0/1
This supports PCIE0/1 on ULCB Kingfisher board

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:21 +02:00
Vladimir Barinov
36bd8e3e34 arm64: dts: ulcb-kf: enable USB2.0 Host channel 0
This supports USB2.0 Host channel 0 on ULCB Kingfisher board

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:21 +02:00
Vladimir Barinov
da9c362908 arm64: dts: ulcb-kf: enable HSUSB
This supports HSUSB on ULCB Kingfisher board

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:20 +02:00
Vladimir Barinov
ba915c12fa arm64: dts: ulcb-kf: enable CAN0/1
This supports CAN0/1 on ULCB Kingfisher board

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:19 +02:00
Vladimir Barinov
c6c816e22b arm64: dts: ulcb-kf: enable SCIF1
This supports SCIF1 on ULCB Kingfisher board

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:19 +02:00
Vladimir Barinov
20913f7e92 arm64: dts: h3ulcb-kf: ES2.0+ SoC initial device tree
Add the initial device tree for the H3ULCB ES2.0+ SoC with Kingfisher
extension infotainment board.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:18 +02:00
Vladimir Barinov
d90e97dfe1 arm64: dts: h3ulcb-kf: ES1.x SoC initial device tree
Add the initial device tree for the H3ULCB ES1.x SoC with Kingfisher
extension infotainment board.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:17 +02:00
Vladimir Barinov
eded6a4d16 arm64: dts: m3ulcb-kf: initial device tree
Add the initial device tree for the M3ULCB with Kingfisher extension
infotainment board.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:17 +02:00
Vladimir Barinov
52cb66073d arm64: dts: ulcb-kf: initial device tree
Add the initial common dtsi file for Kingfisher infotainment board (R-Car
Starter Kit extension)

This commit supports the following peripherals:
- HSCIF0

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:16 +02:00
Yoshihiro Shimoda
b353344475 arm64: dts: renesas: r8a77995: draak: enable PWM channel 0 and 1
This patch enables PWM channel 0 and 1 on the draak. Each channel
connects to LTC2644 for brightness control.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:15 +02:00
Yoshihiro Shimoda
d40a434746 arm64: dts: renesas: r8a77995: add PWM device nodes
This patch adds PWM device nodes for r8a77995.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:14 +02:00
Yoshihiro Shimoda
73de4b8847 arm64: dts: renesas: salvator-common: add pfc node for USB3.0 channel 0
Since a R-Car Gen3 bootloader enables the PFC of USB3.0 channel 0,
the USB3.0 host controller works without this setting on the kernel.
But, this setting should have salvator-common.dtsi. So, this patch
adds the pfc node for USB3.0 channel 0.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2017-10-10 09:51:14 +02:00
Adrian Hunter
eb701ce16a mmc: sdhci-pci: Fix default d3_retune for Intel host controllers
The default for d3_retune is true, but that was not being set in all cases,
which results in eMMC errors because re-tuning has not been done.
Fix by initializing d3_retune to true.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: c959a6b00f ("mmc: sdhci-pci: Don't re-tune with runtime pm for some Intel devices")
Cc: stable@vger.kernel.org # v4.12+
Reported-and-tested-by: ojab <ojab@ojab.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-10-10 08:40:04 +02:00
Jani Nikula
0ead5f81d4 drm/i915/bios: don't pass bdb to parsers that don't parse VBT directly
Hint that you're not supposed to look at VBT in these functions.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b82c326be8c796a70bdc2bd1c479bbb6159f5cb0.1506586821.git.jani.nikula@intel.com
2017-10-10 09:06:33 +03:00
Jani Nikula
0ebdabe612 drm/i915/bios: parse SDVO device mapping from pre-parsed child devices
We parse and store the child devices in
parse_general_definitions(). There is no need to parse the VBT block
again for SDVO device mapping. Do the same as we do in
parse_ddi_ports().

We no longer have access to child device size at this stage, but we also
don't need to worry about reading past the child device anymore. Instead
of a child device size check, do a mild optimization by limiting the
parsing to gens 3 through 7.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c918d4173dd38a165295f1270cb16c2c01bd8cd1.1506586821.git.jani.nikula@intel.com
2017-10-10 09:06:17 +03:00
Jani Nikula
b3ca1f43b2 drm/i915/bios: merge parse_device_mapping() into parse_general_definitions()
They're both parsing the same block, and there's no need for them to be
split. The former also benefits from the range checks in the latter.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/64a292606ecbb0b8602e6c5523c5746573ec3944.1506586821.git.jani.nikula@intel.com
2017-10-10 09:06:10 +03:00
Jani Nikula
53f6b2436e drm/i915/bios: cleanup comments and useless return
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4a95fb9d23d980830e3158d3c57258e6539965ce.1506586821.git.jani.nikula@intel.com
2017-10-10 09:06:02 +03:00
Jani Nikula
127704f547 drm/i915/bios: remove an unnecessary temp variable
Prepare for merging parse_device_mapping() into
parse_general_definitions(). No functional changes.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f1c3621e2622f4debdfb4a2f5c1959845754ac04.1506586821.git.jani.nikula@intel.com
2017-10-10 09:05:54 +03:00
Jani Nikula
2d936f1cf7 drm/i915/bios: don't initialize fields based on vbt version
In theory, these might clobber information for older VBT versions.

We might have to store the BDB version for later parsing, but currently
all code accessing these fields will only use them on newer platforms
with new enough BDB versions.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0232d9cb258e8f83c4180cdb8aad1459a312ec2a.1506586821.git.jani.nikula@intel.com
2017-10-10 09:05:44 +03:00
Jani Nikula
a87145ca56 drm/i915/bios: refactor parse general definitions
Early return on failures. Rename the variable for later merging with
parse_device_mappings().

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/785abb904a572752fec68d90d34efeb67774dc1f.1506586821.git.jani.nikula@intel.com
2017-10-10 09:05:31 +03:00
Jani Nikula
348e4058eb drm/i915/bios: parse DDI ports also for CHV for HDMI DDC pin and DP AUX channel
While technically CHV isn't DDI, we do look at the VBT based DDI port
info for HDMI DDC pin and DP AUX channel. (We call these "alternate",
but they're really just something that aren't platform defaults.)

In commit e4ab73a132 ("drm/i915: Respect alternate_ddc_pin for all DDI
ports") Ville writes, "IIRC there may be CHV system that might actually
need this."

I'm not sure why there couldn't be even more platforms that need this,
but start conservative, and parse the info for CHV in addition to DDI.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100553
Reported-by: Marek Wilczewski <mw@3cte.pl>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d0815082cb98487618429b62414854137049b888.1506586821.git.jani.nikula@intel.com
2017-10-10 09:05:11 +03:00
Kamalesh Babulal
e36a82ee4c powerpc/livepatch: Fix livepatch stack access
While running stress test with livepatch module loaded, kernel bug was
triggered.

  cpu 0x5: Vector: 400 (Instruction Access) at [c0000000eb9d3b60]
  5:mon> t
  [c0000000eb9d3de0] c0000000eb9d3e30 (unreliable)
  [c0000000eb9d3e30] c000000000008ab4 hardware_interrupt_common+0x114/0x120
   --- Exception: 501 (Hardware Interrupt) at c000000000053040 livepatch_handler+0x4c/0x74
  [c0000000eb9d4120] 0000000057ac6e9d (unreliable)
  [d0000000089d9f78] 2e0965747962382e
  SP (965747962342e09) is in userspace

When an interrupt occurs during the livepatch_handler execution, it's
possible for the livepatch_stack and/or thread_info to be corrupted.
eg:

  Task A                        Interrupt Handler
  =========                     =================
  livepatch_handler:
  mr r0, r1
  ld r1, TI_livepatch_sp(r12)
                                hardware_interrupt_common:
                                  do_IRQ+0x8:
                                    mflr    r0          <- saved stack pointer is overwritten
                                    bl      _mcount
                                    ...
                                    std     r27,-40(r1) <- overwrite of thread_info()

  lis r2, STACK_END_MAGIC@h
  ori r2, r2, STACK_END_MAGIC@l
  ld  r12, -8(r1)

Fix the corruption by using r11 register for livepatch stack
manipulation, instead of shuffling task stack and livepatch stack into
r1 register. Using r11 register also avoids disabling/enabling irq's
while setting up the livepatch stack.

Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Reviewed-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
2017-10-10 15:27:42 +11:00
Eric Dumazet
fbb1fb4ad4 net: defer call to cgroup_sk_alloc()
sk_clone_lock() might run while TCP/DCCP listener already vanished.

In order to prevent use after free, it is better to defer cgroup_sk_alloc()
to the point we know both parent and child exist, and from process context.

Fixes: e994b2f0fb ("tcp: do not lock listener to process SYN packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-09 20:55:01 -07:00
Eric Dumazet
9f1c2674b3 net: memcontrol: defer call to mem_cgroup_sk_alloc()
Instead of calling mem_cgroup_sk_alloc() from BH context,
it is better to call it from inet_csk_accept() in process context.

Not only this removes code in mem_cgroup_sk_alloc(), but it also
fixes a bug since listener might have been dismantled and css_get()
might cause a use-after-free.

Fixes: e994b2f0fb ("tcp: do not lock listener to process SYN packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-09 20:55:01 -07:00
Colin Ian King
60942e674e Input: synaptics-rmi4 - make array rmi_f54_report_type_names static
The array rmi_f54_report_type_names is local to the source and does
not need to be in global scope, so make it static. Also make the array
const char * const.

Cleans up sparse warning:
symbol 'rmi_f54_report_type_names' was not declared. Should it be static?

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2017-10-09 20:53:36 -07:00
Andrew Duggan
2b30297d48 Input: synaptics - disable kernel tracking on SMBus devices
In certain situations kernel tracking seems to be getting confused
and incorrectly reporting the slot of a contact. On example is when
the user does a three finger click or tap and then places two fingers
on the touchpad in the same area. The kernel tracking code seems to
continue to think that there are three contacts on the touchpad and
incorrectly alternates the slot of one of the contacts. The result that
is the input subsystem reports a stream of button press and release
events as the reported slot changes.

Kernel tracking was originally enabled to prevent cursor jumps, but it
is unclear how much of an issue kernel jumps actually are. This patch
simply disabled kernel tracking for now.

Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1482640

Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Kamil Páral <kparal@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2017-10-09 20:52:39 -07:00
Bernd Edlinger
812b5ca7d3 Add a driver for Renesas uPD60620 and uPD60620A PHYs
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-09 20:49:36 -07:00
Willem de Bruijn
1e6f74536d vhost_net: do not stall on zerocopy depletion
Vhost-net has a hard limit on the number of zerocopy skbs in flight.
When reached, transmission stalls. Stalls cause latency, as well as
head-of-line blocking of other flows that do not use zerocopy.

Instead of stalling, revert to copy-based transmission.

Tested by sending two udp flows from guest to host, one with payload
of VHOST_GOODCOPY_LEN, the other too small for zerocopy (1B). The
large flow is redirected to a netem instance with 1MBps rate limit
and deep 1000 entry queue.

  modprobe ifb
  ip link set dev ifb0 up
  tc qdisc add dev ifb0 root netem limit 1000 rate 1MBit

  tc qdisc add dev tap0 ingress
  tc filter add dev tap0 parent ffff: protocol ip \
      u32 match ip dport 8000 0xffff \
      action mirred egress redirect dev ifb0

Before the delay, both flows process around 80K pps. With the delay,
before this patch, both process around 400. After this patch, the
large flow is still rate limited, while the small reverts to its
original rate. See also discussion in the first link, below.

Without rate limiting, {1, 10, 100}x TCP_STREAM tests continued to
send at 100% zerocopy.

The limit in vhost_exceeds_maxpend must be carefully chosen. With
vq->num >> 1, the flows remain correlated. This value happens to
correspond to VHOST_MAX_PENDING for vq->num == 256. Allow smaller
fractions and ensure correctness also for much smaller values of
vq->num, by testing the min() of both explicitly. See also the
discussion in the second link below.

Changes
  v1 -> v2
    - replaced min with typed min_t
    - avoid unnecessary whitespace change

Link:http://lkml.kernel.org/r/CAF=yD-+Wk9sc9dXMUq1+x_hh=3ThTXa6BnZkygP3tgVpjbp93g@mail.gmail.com
Link:http://lkml.kernel.org/r/20170819064129.27272-1-den@klaipeden.com
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-09 20:46:39 -07:00
William Tu
ceaa001a17 openvswitch: Add erspan tunnel support.
Add erspan netlink interface for OVS.

Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-09 20:45:50 -07:00
Eric Biggers
cf4c950b87 once: switch to new jump label API
Switch the DO_ONCE() macro from the deprecated jump label API to the new
one.  The new one is more readable, and for DO_ONCE() it also makes the
generated code more icache-friendly: now the one-time initialization
code is placed out-of-line at the jump target, rather than at the inline
fallthrough case.

Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-09 20:26:23 -07:00
David S. Miller
d93fa2ba64 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2017-10-09 20:11:09 -07:00
Wei Wang
d0e60206be ipv6: use rcu_dereference_bh() in ipv6_route_seq_next()
This patch replaces rcu_deference() with rcu_dereference_bh() in
ipv6_route_seq_next() to avoid the following warning:

[   19.431685] WARNING: suspicious RCU usage
[   19.433451] 4.14.0-rc3-00914-g66f5d6c #118 Not tainted
[   19.435509] -----------------------------
[   19.437267] net/ipv6/ip6_fib.c:2259 suspicious
rcu_dereference_check() usage!
[   19.440790]
[   19.440790] other info that might help us debug this:
[   19.440790]
[   19.444734]
[   19.444734] rcu_scheduler_active = 2, debug_locks = 1
[   19.447757] 2 locks held by odhcpd/3720:
[   19.449480]  #0:  (&p->lock){+.+.}, at: [<ffffffffb1231f7d>]
seq_read+0x3c/0x333
[   19.452720]  #1:  (rcu_read_lock_bh){....}, at: [<ffffffffb1d2b984>]
ipv6_route_seq_start+0x5/0xfd
[   19.456323]
[   19.456323] stack backtrace:
[   19.458812] CPU: 0 PID: 3720 Comm: odhcpd Not tainted
4.14.0-rc3-00914-g66f5d6c #118
[   19.462042] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS 1.10.2-1 04/01/2014
[   19.465414] Call Trace:
[   19.466788]  dump_stack+0x86/0xc0
[   19.468358]  lockdep_rcu_suspicious+0xea/0xf3
[   19.470183]  ipv6_route_seq_next+0x71/0x164
[   19.471963]  seq_read+0x244/0x333
[   19.473522]  proc_reg_read+0x48/0x67
[   19.475152]  ? proc_reg_write+0x67/0x67
[   19.476862]  __vfs_read+0x26/0x10b
[   19.478463]  ? __might_fault+0x37/0x84
[   19.480148]  vfs_read+0xba/0x146
[   19.481690]  SyS_read+0x51/0x8e
[   19.483197]  do_int80_syscall_32+0x66/0x15a
[   19.484969]  entry_INT80_compat+0x32/0x50
[   19.486707] RIP: 0023:0xf7f0be8e
[   19.488244] RSP: 002b:00000000ffa75d04 EFLAGS: 00000246 ORIG_RAX:
0000000000000003
[   19.491431] RAX: ffffffffffffffda RBX: 0000000000000009 RCX:
0000000008056068
[   19.493886] RDX: 0000000000001000 RSI: 0000000008056008 RDI:
0000000000001000
[   19.496331] RBP: 00000000000001ff R08: 0000000000000000 R09:
0000000000000000
[   19.498768] R10: 0000000000000000 R11: 0000000000000000 R12:
0000000000000000
[   19.501217] R13: 0000000000000000 R14: 0000000000000000 R15:
0000000000000000

Fixes: 66f5d6ce53 ("ipv6: replace rwlock with rcu and spinlock in fib6_table")
Reported-by: Xiaolong Ye <xiaolong.ye@intel.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-09 19:59:42 -07:00
Ulf Hansson
8055af0a4f ACPI / PM: Remove stale function header
acpi_dev_pm_get_node() isn't used or implemented, so remove it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-10-10 04:13:25 +02:00
Jarkko Nikula
5ab894aee0 device property: Track owner device of device property
Deletion of subdevice will remove device properties associated to parent
when they share the same firmware node after commit 478573c93a (driver
core: Don't leak secondary fwnode on device removal).  This was observed
with a driver adding subdevice that driver wasn't able to read device
properties after rmmod/modprobe cycle.

Consider the lifecycle of it:

parent device registration
	ACPI_COMPANION_SET()
	device_add_properties()
		pset_copy_set()
		set_secondary_fwnode(dev, &p->fwnode)
	device_add()

parent probe
	read device properties
	ACPI_COMPANION_SET(subdevice, ACPI_COMPANION(parent))
	device_add(subdevice)

parent remove
	device_del(subdevice)
		device_remove_properties()
			set_secondary_fwnode(dev, NULL);
			pset_free()

Parent device will have its primary firmware node pointing to an ACPI
node and secondary firmware node point to device properties.

ACPI_COMPANION_SET() call in parent probe will set the subdevice's
firmware node to point to the same 'struct fwnode_handle' and the
associated secondary firmware node, i.e. the device properties as the
parent.

When subdevice is deleted in parent remove that will remove those
device properties and attempt to read device properties in next
parent probe call will fail.

Fix this by tracking the owner device of device properties and delete
them only when owner device is being deleted.

Fixes: 478573c93a (driver core: Don't leak secondary fwnode on device removal)
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2017-10-10 04:09:45 +02:00
Linus Torvalds
529a86e063 Merge branch 'ppc-bundle' (bundle from Michael Ellerman)
Merge powerpc transactional memory fixes from Michael Ellerman:
 "I figured I'd still send you the commits using a bundle to make sure
  it works in case I need to do it again in future"

This fixes transactional memory state restore for powerpc.

* bundle'd patches from Michael Ellerman:
  powerpc/tm: Fix illegal TM state in signal handler
  powerpc/64s: Use emergency stack for kernel TM Bad Thing program checks
2017-10-09 19:08:32 -07:00
David S. Miller
9f7be893ab Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2017-10-09

This series contains updates to i40e and i40evf only.

Jake fixes missed flag conversion from u64 to u32.  Fixes a deafult ITR
value issue where the driver defaults to an ITR value of half the
expected value (in terms of minimum microseconds between interrupts).  So
fix this by changing the default values to be calculated using the
ITR_REG_TO_USEC() macro which indicates that we are converting from the
register units into microseconds. Updates the drivers to bump the tail in
increments of 8 and double the number of descriptors we will bundle into
one tail bump when receiving.  With the recent kernel support for
enabling XPS and QoS at the same time, we no longer need to worry about
the number of traffic classes when enabling XPS.

Lihong converts the use of hash_for_each() to hash_for_each_safe() to
safely remove a hash entry.  Adds a check for the return value for
find_first_bit() in the case that it returns the size passed to search.

Alan fixes a bug in which filters are erroneously removed if they are
removed and then added again.  So make sure that when adding a filter, if
we find it already existed in our list, make sure it is not marked to be
removed.

Jayaprakash adds the retrying of PHY reads when the I2C is busy for a
maximum period of 500ms.

Rami fixes code comment typo.

Stefano Brivio simplifies the code by removing the use of a local
return code variable and simply return the results of the read function.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-09 18:12:03 -07:00
Masahiro Yamada
2c1f4f1251 kbuild: re-order the code to not parse unnecessary variables
The top Makefile is divided into some sections such as mixed targets,
config targets, build targets, etc.

When we build mixed targets, Kbuild just invokes submake to process
them one by one.  In this case, compiler-related variables like CC,
KBUILD_CFLAGS, etc. are unneeded.

Check what kind of targets we are building first, and parse variables
for building only when necessary.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-10 10:01:29 +09:00
Masahiro Yamada
ba634eceb5 kbuild: move "_all" target out of $(KBUILD_SRC) conditional
The first "_all" occurrence around line 120 is only visible when
KBUILD_SRC is unset.

If O=... is specified, the working directory is relocated, then the
only second occurrence around line 193 is visible, that is not set
to PHONY.

Move the first one to an always visible place.  This clarifies "_all"
is our default target and it is always set to PHONY.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
2017-10-10 10:00:47 +09:00
Masahiro Yamada
9d022c5406 kbuild: replace $(hdr-arch) with $(SRCARCH)
Since commit 5e53879008 ("sparc,sparc64: unify Makefile"), hdr-arch
and SRCARCH always match.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
2017-10-10 10:00:47 +09:00
Ard Biesheuvel
19f3f22aad dt-bindings: PCI: designware: Add binding for Designware PCIe in ECAM mode
Describe the binding for firmware-configured instances of the Synopsys
DesignWare PCIe controller in RC mode, that are almost but not quite ECAM
compliant.

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
2017-10-09 19:11:28 -05:00
Kees Cook
96ca579a1e waitid(): Add missing access_ok() checks
Adds missing access_ok() checks.

CVE-2017-5123

Reported-by: Chris Salls <chrissalls5@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Fixes: 4c48abe91b ("waitid(): switch copyout of siginfo to unsafe_put_user()")
Cc: stable@kernel.org # 4.13
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-10-09 17:03:31 -07:00
David S. Miller
0349a86c85 Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2017-10-09

This series contains updates to ixgbe only.

Emil fixes an issue where the semaphore bits could be stuck after a reset
or a crash, by adding the clearing of software resource bits in the
software/firmware synchronization register.  Added error checks when we
attempt to identify and initialize the PHY to prevent a crash.  Fixed a
few issues in the logic of ixgbe_clean_test_rings() which was exposed by
a previous commit that was causing a crash in ethtool diagnostics.

Bhumika Goyal fixes a couple of instances which were overlooked when we
made ixgbe_mac_operations constant.

Shannon Nelson fixes an issue to restore normal operations after the
last MACVLAN offload is removed, otherwise we get stuck in a single queue
operations.

The infamous Jesper Dangaard Brouer adds a counter which counts the
number of times the recycle fails and the real page allocator is invoked.

Alex updates the adaptive ITR algorithm to better support the needs of the
network.  This attempt to make it so that our ITR algorithm will try to
prevent either starving a socket buffer for memory in the case of
transmit, or overrunning an receive socket buffer on receive.  We should
function better with new features like XDP which can handle small packets
at high rates without needing to lock us into NAPI polling mode.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-09 16:38:52 -07:00
Linus Torvalds
ff33952e4d Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:

 1) Fix object leak on IPSEC offload failure, from Steffen Klassert.

 2) Fix range checks in ipset address range addition operations, from
    Jozsef Kadlecsik.

 3) Fix pernet ops unregistration order in ipset, from Florian Westphal.

 4) Add missing netlink attribute policy for nl80211 packet pattern
    attrs, from Peng Xu.

 5) Fix PPP device destruction race, from Guillaume Nault.

 6) Write marks get lost when BPF verifier processes R1=R2 register
    assignments, causing incorrect liveness information and less state
    pruning. Fix from Alexei Starovoitov.

 7) Fix blockhole routes so that they are marked dead and therefore not
    cached in sockets, otherwise IPSEC stops working. From Steffen
    Klassert.

 8) Fix broadcast handling of UDP socket early demux, from Paolo Abeni.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
  cdc_ether: flag the u-blox TOBY-L2 and SARA-U2 as wwan
  net: thunderx: mark expected switch fall-throughs in nicvf_main()
  udp: fix bcast packet reception
  netlink: do not set cb_running if dump's start() errs
  ipv4: Fix traffic triggered IPsec connections.
  ipv6: Fix traffic triggered IPsec connections.
  ixgbe: incorrect XDP ring accounting in ethtool tx_frame param
  net: ixgbe: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag
  Revert commit 1a8b6d76dc ("net:add one common config...")
  ixgbe: fix masking of bits read from IXGBE_VXLANCTRL register
  ixgbe: Return error when getting PHY address if PHY access is not supported
  netfilter: xt_bpf: Fix XT_BPF_MODE_FD_PINNED mode of 'xt_bpf_info_v1'
  netfilter: SYNPROXY: skip non-tcp packet in {ipv4, ipv6}_synproxy_hook
  tipc: Unclone message at secondary destination lookup
  tipc: correct initialization of skb list
  gso: fix payload length when gso_size is zero
  mlxsw: spectrum_router: Avoid expensive lookup during route removal
  bpf: fix liveness marking
  doc: Fix typo "8023.ad" in bonding documentation
  ipv6: fix net.ipv6.conf.all.accept_dad behaviour for real
  ...
2017-10-09 16:25:00 -07:00
Aleksander Morgado
fdfbad3256 cdc_ether: flag the u-blox TOBY-L2 and SARA-U2 as wwan
The u-blox TOBY-L2 is a LTE Cat 4 module with HSPA+ and 2G fallback.
This module allows switching to different USB profiles with the
'AT+UUSBCONF' command, and provides a ECM network interface when the
'AT+UUSBCONF=2' profile is selected.

The u-blox SARA-U2 is a HSPA module with 2G fallback. The default USB
configuration includes a ECM network interface.

Both these modules are controlled via AT commands through one of the
TTYs exposed. Connecting these modules may be done just by activating
the desired PDP context with 'AT+CGACT=1,<cid>' and then running DHCP
on the ECM interface.

Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-10-09 16:03:32 -07:00