dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191212135550.4634-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlike irq_of_parse_and_map() which has a dummy definition on SPARC,
of_irq_to_resource() hasn't.
But as platform_get_irq() can be used instead and is generic, use it.
Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Mark Brown <broonie@kernel.org>
Fixes: 3194d2533e ("spi: fsl: don't map irq during probe")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/091a277fd0b3356dca1e29858c1c96983fc9cb25.1576172743.git.christophe.leroy@c-s.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: a5356aef6a ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20191211195730.26794-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
platform device aliases were missing, preventing
autoloading of module.
Fixes: 811b700630 ("regulator: rn5t618: add driver for Ricoh RN5T618 regulators")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20191211221600.29438-1-andreas@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
According to user manual, it is required that FLL_LAMBDA > 0
in all cases (Integer and Franctional modes).
Fixes: 9a76f1ff6e ("ASoC: Add initial WM8962 CODEC driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1576065442-19763-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the driver submits multiple commands in a row it makes sense to
notify the host only after submitting the last one, so the host can
process them all at once, with a single vmexit.
Add functions to enable/disable notifications to allow that. Use the
new functions for primary plane updates.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20191212125346.8334-3-kraxel@redhat.com
Tuning support in DDR50 speed mode was added in SD Specifications Part1
Physical Layer Specification v3.01. Its not possible to distinguish
between v3.00 and v3.01 from the SCR and that is why since
commit 4324f6de6d ("mmc: core: enable CMD19 tuning for DDR50 mode")
tuning failures are ignored in DDR50 speed mode.
Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this
error gets printed during enumeration and also if retune is triggered at
any time during operation. Update the printk level to pr_debug so that
these errors don't lead to false error reports.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: stable@vger.kernel.org # v4.4+
Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Document support for the SDHI controller in the Renesas R-Car M3-W+
(R8A77961) SoC.
Update all references to R-Car M3-W from "r8a7796" to "r8a77960", to
avoid confusion between R-Car M3-W (R8A77960) and M3-W+.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20191205134349.6410-2-geert+renesas@glider.be
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
New datasheets require different and new values for HS400 with 4taps or
8taps.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-6-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that the quirks structure is accessible, we can remove the TMIO flag
for HS400 using only 4 taps. This is Renesas specific anyhow.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will need that for a later patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The warning is not solely used for SDR104 anymore, but for all which
require tuning.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The two devices next to each other are super similar, but still, let's
keep the alphanumeric sorting for easier additions later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We know now that there won't be Gen3 SoCs with both, SYS-DMAC and
internal DMAC. We removed the blacklisting for SYS-DMAC already, so we
can remove the whitelisting for internal DMAC, too. This makes adding
new SoCs easier. We keep the quirk handling, of course.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203194859.917-1-wsa@the-dreams.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The STOP command is disabled for multiple blocks r/w commands
with auto CMD12, when start to send. However, if there is data
error, software still needs to send CMD12 according to SD spec.
This patch is to allow software CMD12 sending for this case.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191114111814.35199-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code in mmc_spi_initsequence() tries to send a burst with
high chipselect and for this reason hardcodes the device into
SPI_CS_HIGH.
This is not good because the SPI_CS_HIGH flag indicates
logical "asserted" CS not always the physical level. In
some cases the signal is inverted in the GPIO library and
in that case SPI_CS_HIGH is already set, and enforcing
SPI_CS_HIGH again will actually drive it low.
Instead of hard-coding this, toggle the polarity so if the
default is LOW it goes high to assert chipselect but if it
is already high then toggle it low instead.
Cc: Phil Elwell <phil@raspberrypi.org>
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20191204152749.12652-1-linus.walleij@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the SAM9x60 SoC, there are only two clocks instead of three for the
SDHCI device. The base clk is no longer provided, it is generated
internally from the mult clk.
The values of the base clk and mul in the capabilities registers may not
reflect the reality as the mult clk is a programmable clock which can take
several rates. As we can't trust those values, take them from the clock
tree and update the capabilities according to.
As we can have the same pitfall, in some cases, with the SAMA5D2 Soc,
stop relying on capabilities too.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191128074522.69706-2-ludovic.desroches@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a new compatible string for the SAM9X60 sdhci device. It involves
an update of the properties about the clocks stuff.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191128074522.69706-1-ludovic.desroches@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tuning support in DDR50 speed mode was added in SD Specifications Part1
Physical Layer Specification v3.01. Its not possible to distinguish
between v3.00 and v3.01 from the SCR and that is why since
commit 4324f6de6d ("mmc: core: enable CMD19 tuning for DDR50 mode")
tuning failures are ignored in DDR50 speed mode.
Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this
error gets printed during enumeration and also if retune is triggered at
any time during operation. Update the printk level to pr_debug so that
these errors don't lead to false error reports.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: stable@vger.kernel.org # v4.4+
Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 5dd1955225.
First, the fix seems to be plain wrong, since the erratum suggests
waiting 5ms before setting setting SYSCTL[RSTD], but this msleep()
happens after the call of sdhci_reset() which is where that bit gets
set (if SDHCI_RESET_DATA is in mask).
Second, walking the whole device tree to figure out if some node has a
"fsl,p2020-esdhc" compatible string is hugely expensive - about 70 to
100 us on our mpc8309 board. Walking the device tree is done under a
raw_spin_lock, so this is obviously really bad on an -rt system, and a
waste of time on all.
In fact, since esdhc_reset() seems to get called around 100 times per
second, that mpc8309 now spends 0.8% of its time determining that
it is not a p2020. Whether those 100 calls/s are normal or due to some
other bug or misconfiguration, regularly hitting a 100 us
non-preemptible window is unacceptable.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191204085447.27491-1-linux@rasmusvillemoes.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
there is a chance that always get response CRC error after HS200 tuning,
the reason is that need set CMD_TA to 2. this modification is only for
MT8173.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: stable@vger.kernel.org
Fixes: 1ede5cb88a ("mmc: mediatek: Use data tune for CMD line tune")
Link: https://lore.kernel.org/r/20191204071958.18553-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The DDR_CONFIG register offset got updated after a specific
minor version of sdcc V4. This offset change has not been properly
taken care of while updating register changes for sdcc V5.
Correcting proper offset for this register.
Also updating this register value to reflect the recommended RCLK
delay.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/0101016ea738ec72-fa0f852d-20f8-474a-80b2-4b0ef63b132c-000000@us-west-2.amazonses.com
Fixes: f15358885d ("mmc: sdhci-msm: Define new Register address map")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit c894e33ddc.
This commit aims to treat SD High speed and SDR25 as the same while
setting UHS Timings in HOST_CONTROL2 which leads to failures with some
SD cards in AM65x. Revert this commit.
The issue this commit was trying to fix can be implemented in a platform
specific callback instead of common sdhci code.
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191128110422.25917-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of only setting mode->specified on false on an early exit and
leaving e.g. mode->bpp_specified and mode->refresh_specified as is,
lets be consistent and just zero out the entire passed in struct at
the top of drm_mode_parse_command_line_for_connector()
Changes in v3:
-Drop "mode->specified = false;" line instead of the "return false;" (oops)
This crasher was reported-by: kernel test robot <lkp@intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-11-hdegoede@redhat.com
fb_get_options() will return fb_mode_option if no video=<connector-name>
argument is present on the kernel commandline, so there is no need to also
do this in drm_mode_parse_command_line_for_connector() as our only caller
uses fb_get_options() to get the mode_option argument.
Changes in v2:
-Split out the changes dealing with the initialization of the mode struct
into a separate patch
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-10-hdegoede@redhat.com
Sometimes we want to override a connector's panel_orientation from the
kernel commandline. Either for testing and for special cases, e.g. a kiosk
like setup which uses a TV mounted in portrait mode.
Users can already specify a "rotate" option through a video= kernel cmdline
option. But that only supports 0/180 degrees (see drm_client_modeset TODO)
and only works for in kernel modeset clients, not for userspace kms users.
The "panel-orientation" connector property OTOH does support 90/270 degrees
as it leaves dealing with the rotation up to userspace and this does work
for userspace kms clients (at least those which support this property).
Changes in v2:
-Add missing ':' after @panel_orientation (reported by kbuild test robot)
BugLink: https://gitlab.freedesktop.org/plymouth/plymouth/merge_requests/83
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-9-hdegoede@redhat.com
Some options which can be specified on the commandline, such as
margin_right=..., margin_left=..., etc. are applied not only to the
specified mode, but to all modes. As such it would be nice if the user
can simply say e.g.
video=HDMI-1:margin_right=14,margin_left=24,margin_bottom=36,margin_top=42
This commit refactors drm_mode_parse_command_line_for_connector() to
add support for this, and as a nice side effect also cleans up the
function a bit.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-8-hdegoede@redhat.com
drm_connector_get_cmdline_mode() calls
drm_mode_parse_command_line_for_connector() with &connector->cmdline_mode
as mode argument, so anything which we store in the mode arguments gets
kept even if we return false.
Avoid storing a possibly false-postive bpp/refresh_specified setting
in connector->cmdline_mode by moving the setting of these to after
successful parsing of the bpp/refresh parts of the video= argument.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-7-hdegoede@redhat.com
Add a freestanding function argument to drm_mode_parse_cmdline_options()
similar to how drm_mode_parse_cmdline_extra() already has this.
This is a preparation patch for allowing parsing of stand-alone options
without a mode before them, e.g.: video=HDMI-1:margin_right=14,...
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-6-hdegoede@redhat.com
Refactor drm_mode_parse_cmdline_options() so that it takes a pointer
to the first option, rather then a pointer to the ',' before the first
option.
This is a preparation patch for allowing parsing of stand-alone options
without a mode before them, e.g.: video=HDMI-1:margin_right=14,...
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-5-hdegoede@redhat.com
Before this commit it was impossible to combine an extra mode argument
specified directly after the resolution with an option, e.g.
video=HDMI-1:720x480e,rotate=180 would not work, either the "e" to force
enable would need to be dropped or the ",rotate=180", otherwise the
mode_option would not be accepted.
This commit fixes this by setting parse_extras to true in this case, so
that drm_mode_parse_cmdline_res_mode() parses the extra arguments directly
after the resolution.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-4-hdegoede@redhat.com
Before this commit it was impossible to add an extra mode argument after
a bpp or refresh specifier, combined with an option, e.g.
video=HDMI-1:720x480-24e,rotate=180 would not work, either the "e" to
force enable would need to be dropped or the ",rotate=180", otherwise
the mode_option would not be accepted.
This commit fixes this by fixing the length calculation if extras_ptr
is set to stop the extra parsing at the start of the options (stop at the
',' options_ptr points to).
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-3-hdegoede@redhat.com
Before this commit, if the last option of a video=... option is for
example "rotate" without a "=<value>" after it then delim will point to
the terminating 0 of the string, and value which is sets to <delim + 1>
will point one position past the end of the string.
This commit fixes this by enforcing that the contents of delim equals '='
as it should be for options which take a value, this check is done in a
new drm_mode_parse_cmdline_int helper function which factors out the
common integer parsing code for all the options which take an int.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191118155134.30468-1-hdegoede@redhat.com
Clean up acpi_processor_evaluate_cst() in multiple ways:
* Rename current_count to last_index which matches the purpose of
the variable better.
* Consistently use acpi_handle_*() for printing messages and make
the messages cleaner.
* Drop redundant parens and braces.
* Rewrite and clarify comments.
* Rearrange checks and drop the redundant ones.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order to separate the ACPI _CST evaluation from checks
specific to the ACPI processor driver, move the majority of
the acpi_processor_get_power_info_cst() function body to a new
function, acpi_processor_evaluate_cst(), that will extract
the C-states information from _CST output, and redefine
acpi_processor_get_power_info_cst() as a wrapper around it.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The intel_idle driver will be modified to use ACPI _CST subsequently
and it will need to notify the platform firmware of that if
acpi_gbl_FADT.cst_control is set, so add a routine for this purpose,
acpi_processor_claim_cst_control(), to acpi_processor.c (so that it
is always present which is required by intel_idle) and export it
to allow the ACPI processor driver (which is modular) to call it.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Log (if debug > 0) when a CEC message is received.
This is done for transmits already, so it makes sense to do the
same for receives.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Don't schedule the next ping before the current ping is
sent, schedule it after.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Don't free everything in the disconnect callback, instead use
the adap_free callback, which is called when the last open
filehandle is closed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It turns out that received CEC messages can arrive faster than
can be processed by the CEC framework, resulting in lost messages.
Instead of storing only one CEC message, store up to 8.
Also fix a bug where the EOM bit wasn't checked for a received
message of length 1, so POLL messages weren't properly reported.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add the compatible and GRF definitions for the PX30 soc.
changes in v5:
- rebased on top of 5.5-rc1
- merged with dsi timing change to prevent ordering conflicts
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191209143130.4553-7-heiko@sntech.de
The px30 SoC also uses a dw-mipi-dsi controller, so add the
compatible value for it.
changes in v5:
- rebased on top of 5.5-rc1
- merged with dsi timing change to prevent ordering conflicts
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191209143130.4553-6-heiko@sntech.de
