In case a tx queue wake call arrives after a client has transitioned to
powersave, make sure that the queue is not kept active until the client
has left powersave mode
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Take into account device rx stream in mt76x02_mac_process_rate
in order to not report wrong number of rx spatial stream to mac80211.
The issue has been reported on mt76x0 device which is 1x1:1 however
the hw sometimes reports rx nss equal to 2
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The generic EWMA code cannot deal with negative numbers, so convert signal
to a positive number before adding it
Fixes mt76x2 AGC tuning
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The hardware does not deal with multiple WCID entries for the same station
properly. Set IEEE80211_HW_NEEDS_UNIQUE_STA_ADDR to avoid those cases
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On MT76x2, the hardware does not report tx status in the FIFO register,
if the packet id is 0.
Change the allocation of packet IDs to use 0 for no-ack packets, 1 for
non-probing packets and 2-255 for packets with tx status requested.
Fixes rate control issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x02 led support in mt76x02-lib module in order to
add tpt led trigger to mt76x0e driver
Tested-by: LGA1150 <dqfext@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use proper name for __MT76x02_H macro in mt76x02.h
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Call mt76_dma_add_buf routine directly in mt76_dma_tx_queue_skb
and avoid indirect call if not necessary
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Don't populate the const array 'data' on the stack but instead
make it static. Makes the object code smaller by 78 bytes:
Before:
text data bss dec hex filename
5438 1080 0 6518 1976 mediatek/mt76/mt76x2/usb_mcu.o
After:
text data bss dec hex filename
5296 1144 0 6440 1928 mediatek/mt76/mt76x2/usb_mcu.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Port mt76x02_check_tx_hang watchdog from vendor driver in order to
perform a device reset when tx mac/dma logic hangs. Tx mac/dma stuck
has been observed when the device is heavy loaded or in a noisy
environment. Moreover introduce wdt delayed work in order to run
tx_hang watchdog. For the moment run mt76x02_check_tx_hang watchdog
just on mt76x2 devices since the issue has not been observed on mt76x0
driver yet
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Precompute data length in order to avoid to allocate the related
skb data structure if reported length does not fit in queue buf_size
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Do not set bw variable to zero for legacy rates since it is already
initialized to zero. Moreover set nss to 1 just for legacy rates
since nss will be properly set for VHT/HT rates
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ported from the reference driver. Should fix compliance with ETSI
regulatories on preventing transmission while energy detect values
are above the threshold.
The code has been tested using an ath9k device running tx99 as
noise generator
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update default value for MT_TX_LINK_CFG according to vendor driver
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Grab mt76_dev mutex in mt76x02_dfs_set_domain since it runs
concurrently with mt76x{0,2}_set_channel routines
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add static qualifier to mt76x2_init_hardware routine since it is
used just in pci_init.c
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure MT_VHT_HT_FBK_CFG1 values similar like vendor driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Configure protection based on information that are provided to
us either by remote AP or by hostapd via HT operation IE.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On new mt76 chips, phy mode is configured by last 3 bits
of rate value. Hence OFDM bit is marked by 0x2000
instead of 0x4000.
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use set_rts_threshold calback to enable/disable threshold only for
legacy traffic.
Protection for HT and VHT traffic is defined by HT operation element
and it's provided by remote AP or by hostapd.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As already done for pcie code in commit 79d1c94c9c ("mt76: avoid
queue/status spinlocks while passing tx status to mac80211") make sure
that no tx related spinlocks are taken during the ieee80211_tx_status call
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Grab mt76_dev mutex in mt76x02_mac_work handler since it runs
concurrently with mt76x{0,2}_set_channel routines
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reconfigure properly MT_MAC_SYS_CTRL register after mac sw-reset
in mt76x02_check_mac_err routine
Fixes: 73556561ab ("mt76x0: use mt76x02_mac_work as stats handler")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MODULE_FIRMWARE() is used in usb_mcu.c and provided by linux/module.h,
but this header file is not directly included. This causes problems in
backports with some kernel versions.
Add the missing include.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Precompute data length in order to avoid to allocate the related
skb data structure if reported length does not fit in queue buf_size
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove napi from mt76_dma_rx_fill routine signature since
it is a leftover of a previous implementation and it is no
longer used
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
So far the code only validates the buffer size of the first skb.
Extend this check to cover additional fragments as well, in case the size
is corrupted during a DMA reset.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The linux-firmware brcmfmac firmware files contain an embedded table with
per country allowed channels and strength info.
For recent hardware these versions of the firmware are specially build for
linux-firmware, the firmware files directly available from Cypress rely on
a separate clm_blob file for this info.
For some unknown reason Cypress refuses to provide the standard firmware
files + clm_blob files it uses elsewhere for inclusion into linux-firmware,
instead relying on these special builds with the clm_blob info embedded.
This means that the linux-firmware firmware versions often lag behind,
but I digress.
The brcmfmac driver does support the separate clm_blob file and always
tries to load this. Currently we use request_firmware for this. This means
that on any standard install, using the standard combo of linux-kernel +
linux-firmware, we will get a warning:
"Direct firmware load for ... failed with error -2"
On top of this, brcmfmac itself prints: "no clm_blob available (err=-2),
device may have limited channels available".
This commit switches to firmware_request_nowarn, fixing almost any brcmfmac
device logging the warning (it leaves the brcmfmac info message in place).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a system warning message, warn_slowpath-fmt, during suspend
while using supplicant join AP and enable wowl feature by IW command.
It's caused by brcmf_pno_remove_request path can't find the reqid.
This fix will not go to remove pno request function if there is no
pno scan.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Lo-Hsiang Lo <double.lo@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Accessing struct device is pretty useful/common so having a direct
pointer:
1) Simplifies some code
2) Makes bcma_bus_get_host_dev() unneeded
3) Allows further improvements like using dev_* printing helpers
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the current approach of scanning, roaming delays are observed.
Firmware has support for back ground scanning. To get this advantage,
mac80211 hardware scan is implemented, which decides type of scan to
do based on connected state.
When station is in not connected, driver returns with special value 1
to trigger software scan in mac80211. In case of connected state,
background scan will be triggered.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_register() may fail, so let's check its status and issue an error
message if it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Drop LIST_HEAD where the variable it declares has never
been used.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier x;
@@
- LIST_HEAD(x);
... when != x
// </smpl>
Fixes: a910e4a94f ("cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the missing unlock before return from function cw1200_hw_scan()
in the error handling case.
Fixes: 4f68ef64cd ("cw1200: Fix concurrency use-after-free bugs in cw1200_hw_scan()")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Point of View TAB-P1006W-232 tablet contains quite generic names in
the sys_vendor and product_name DMI strings, without this patch brcmfmac
will try to load: brcmfmac43340-sdio.Insyde-BayTrail.txt as nvram file
which is a bit too generic.
Add a DMI quirk so that a unique and clearly identifiable nvram file
name is used on the PoV TAB-P1006W-232 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently array element org[3] is being accessed, however the array is
only 3 elements in size, so this looks like an off-by-one out-of-bounds
error. Fix this by using org[2], which I believe was the original
intent.
This issue has existed in the driver back in the pre-git days, so no
idea when it was introduced.
Detected by CoverityScan, CID#711344 ("Out-of-bounds read")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:1202:5: warning: variable 'phybw40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4625:5: warning: variable 'phybw40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4834:5: warning: variable 'phybw40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:3085:17: warning: variable 'maxtargetpwr' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_lcn.c:4215:17: warning: variable 'maxtargetpwr' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not implement
mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=I+r6
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not
implement mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
* tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: rename generated .*conf-cfg to *conf-cfg
kbuild: remove unnecessary stubs for archheader and archscripts
kbuild: use assignment instead of define ... endef for filechk_* rules
arch: remove redundant UAPI generic-y defines
kbuild: generate asm-generic wrappers if mandatory headers are missing
arch: remove stale comments "UAPI Header export list"
riscv: remove redundant kernel-space generic-y
kbuild: change filechk to surround the given command with { }
kbuild: remove redundant target cleaning on failure
kbuild: clean up rule_dtc_dt_yaml
kbuild: remove UIMAGE_IN and UIMAGE_OUT
jump_label: move 'asm goto' support test to Kconfig
kallsyms: lower alignment on ARM
scripts: coccinelle: boolinit: drop warnings on named constants
scripts: coccinelle: check for redeclaration
kconfig: remove unused "file" field of yylval union
nds32: remove redundant kernel-space generic-y
nios2: remove unneeded HAS_DMA define
Pull perf tooling updates form Ingo Molnar:
"A final batch of perf tooling changes: mostly fixes and small
improvements"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (29 commits)
perf session: Add comment for perf_session__register_idle_thread()
perf thread-stack: Fix thread stack processing for the idle task
perf thread-stack: Allocate an array of thread stacks
perf thread-stack: Factor out thread_stack__init()
perf thread-stack: Allow for a thread stack array
perf thread-stack: Avoid direct reference to the thread's stack
perf thread-stack: Tidy thread_stack__bottom() usage
perf thread-stack: Simplify some code in thread_stack__process()
tools gpio: Allow overriding CFLAGS
tools power turbostat: Override CFLAGS assignments and add LDFLAGS to build command
tools thermal tmon: Allow overriding CFLAGS assignments
tools power x86_energy_perf_policy: Override CFLAGS assignments and add LDFLAGS to build command
perf c2c: Increase the HITM ratio limit for displayed cachelines
perf c2c: Change the default coalesce setup
perf trace beauty ioctl: Beautify USBDEVFS_ commands
perf trace beauty: Export function to get the files for a thread
perf trace: Wire up ioctl's USBDEBFS_ cmd table generator
perf beauty ioctl: Add generator for USBDEVFS_ ioctl commands
tools headers uapi: Grab a copy of usbdevice_fs.h
perf trace: Store the major number for a file when storing its pathname
...
