The driver must free the IRQ in remove() to prevent the potential race
where an IRQ starts to be handled while the driver is being removed but
devres has not yet called free_irq(). However, the driver can run without
an interrupt but devm_free_irq() will hit a WARN() if no devres-managed
interrupt was ever created.
Fix this by only attempting to create the interrupt handler if the hardware
config specified an interrupt, and failing probe() if the interrupt could
not be created. This means that in cs42l42_remove() an interrupt must have
been registered if the irq number is valid and therefore it is safe to call
devm_free_irq().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-16-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet the SRC MCLK must be as near as possible to
(125 * sample rate). This means it should be ~6MHz for rates up to 48k
and ~12MHz for rates above that. As per datasheet table 4-21.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-14-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After enabling the HP or ADC by writing the corresponding PDN=0,
it takes around 20 milliseconds for it to power up and the midrail
supply to be stable. Add this wait into a DAPM widget callback.
If HP and ADC are both powering up in a DAPM sequence, there's no
need to do the wait twice. The widget will perform one wait in the
POST_PMU if there was a PRE_PMU for one or both.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-13-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It isn't possible to switch MCLK between 12MHz and 24MHz rate groups
on-the-fly - this can only be done when cs42l42 is powered-down.
All "normal" SCLK rates use an MCLK in the 12MHz group, so change the
configs for SCLK > 12.288 MHz to use the PLL to generate an MCLK in
the 12MHz group.
As this means MCLK_DIV is always 0 it can be removed from the pll
configuration setup.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-12-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver currently only supports configuring for sample rates <= 96k
and it isn't possible to setup a configuration that will support all
sample rates up to 192k.
For sample rates up to 96k MCLK is in the 12MHz group.
However, although 192k only requires an I2S clock in the 12MHz group,
the cs42l42 audio path is not natively 192k so the audio must be
resampled. But for 192k the SRC requires a 24MHz MCLK.
It is not possible to switch MCLK between 12MHz and 24MHz groups
on-the-fly. The 12MHz group supports all sample rates up to 96k.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-11-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver can run without an interrupt so if devm_request_threaded_irq()
failed, the probe() just carried on. But if this was EPROBE_DEFER the
driver would continue without an interrupt instead of deferring to wait
for the interrupt to become available.
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-6-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An I2S frame always has two slots (left and right) even when sending
mono. The right channel (channel 2) of ASP TX will always have the
same bit width as the left channel and will always be on the high
phase of LRCLK.
The previous implementation always passed the field masks for both
channels to snd_soc_component_update_bits() but for mono the written value
only contained the settings for channel 1. The result was that for mono
channel 2 was set to 8-bit (which is an invalid configuration) with both
channels on the low phase of LRCLK.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 585e7079de ("ASoC: cs42l42: Add Capture Support")
Link: https://lore.kernel.org/r/20211015133619.4698-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When capture and playback substreams are both running at the same time,
cs42l42_pcm_hw_params() would be called for each direction. The first
call will configure the PLL. The second call must not write the PLL
configuration registers again if the first substream is already running,
as this could destabilize the PLL.
The DAI is marked symmetric sample bits and sample rate, so the two
directions will always have the same SCLK (I2S always has 2 channel slots
so the DAI does not need to require symmetric channels to guarantee the
same SCLK). However, since cs42l42_pll_config() is checking for an active
stream it may as well test that the requested SCLK is the same as the
currently active configuration.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
show() must not use snprintf() when formatting the value to be
returned to user space.
Fix the following coccicheck warning:
drivers/spi/spi-tle62x0.c:144: WARNING: use scnprintf or sprintf.
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Signed-off-by: Qing Wang <wangqing@vivo.com>
Link: https://lore.kernel.org/r/1634280668-4954-1-git-send-email-wangqing@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix following coccicheck warning:
./drivers/spi/spi-cadence-xspi.c:490:1-23: WARNING: Function
for_each_child_of_node should have of_node_put() before return
Early exits from for_each_child_of_node should decrement the
node reference counter.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20211015033919.5915-1-wanjiabing@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix following coccicheck warning:
./drivers/spi/spi-orion.c:738:1-33: WARNING: Function
for_each_available_child_of_node should have of_node_put() before goto
Early exits from for_each_available_child_of_node should decrement the
node reference counter.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20211015034008.6357-1-wanjiabing@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently errors on register read/write/update are reported with
an error code and the corresponding function but does not provide
any details on the which register number did it actually fail.
register number can give better clue and it should be easy to
locate the code and fix.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211014161330.26645-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Codec2Codec-Multi sample to audio-graph-card2-custom-sample.dtsi.
Because it can use very basic connection only for now,
it can use only
- 2channels
- S32_LE format
Test-Component driver has "IN" and "OUT" widget. Thus the route is
+--+ +-+
| | | |- Codec8 <- IN
| | <- | |- Codec9 <- IN
| | +-+
| |
| | +-+
| | -> | |- Codec10 -> OUT
| | | |- Codec11 -> OUT
+--+ +-+
One note here is that it will start works when it boot.
In other words we can't stop it so far.
We need to update driver for it in the future.
...
asoc-audio-graph-card2-custom-sample: multicodec <-> multicpu mapping ok
test-component test_codec: test_dai_startup() : test_codec.9
test-component test_codec: test_dai_startup() : test_codec.8
test-component test_codec: test_dai_startup() : test_codec.11
test-component test_codec: test_dai_startup() : test_codec.10
...
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87mtnelu2k.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Codec2Codec-Single sample to audio-graph-card2-custom-sample.dtsi.
Because it can use very basic connection only for now,
it can use only
- 2channels
- S32_LE format
Test-Component driver has "IN" and "OUT" widget. Thus the route is
+--+
| | <-- Codec6 <-- IN
| | --> Codec7 --> OUT
+--+
One note here is that it will start works when it boot.
In other words we can't stop it so far.
We need to update driver for it in the future.
...
asoc-audio-graph-card2-custom-sample: test_codec.7 <-> test_codec.6 mapping ok
test-component test_codec: test_dai_startup() : test_codec.6
test-component test_codec: test_dai_startup() : test_codec.7
...
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o87ulu2o.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds DPCM link Multi-CPU/Codec sample to
audio-graph-card2-custom-sample.dtsi.
This sample is assuming MIXer connection.
One note is that Multi-FE is not supported on ASoC
FE BE
**** +-+
CPU5 -- * * -- | | -- Codec4
CPU6 -- * * | | -- Codec5
**** +-+
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87pmsalu2s.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds DPCM link Single-CPU/Codec sample to
audio-graph-card2-custom-sample.dtsi.
This sample is assuming MIXer connection.
FE BE
****
CPU3 -- * * -- Codec3
CPU4 -- * *
****
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r1cqlu2w.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Audio Graph Card2 settings is a little bit difficult for beginner,
and Customizing it also difficult/confusable too.
So, this patch adds sample for it.
You can easily use it by adding below line on your DT file,
and select CONFIGs to your .config.
#include "../../../../../sound/soc/generic/audio-graph-card2-custom-sample.dtsi"
CONFIG_SND_AUDIO_GRAPH_CARD2
CONFIG_SND_AUDIO_GRAPH_CARD2_CUSTOM_SAMPLE
CONFIG_SND_TEST_COMPONENT
This patch uses audio-graph-card2 base custom sample driver.
You can directly use audio-graph-card2 instead of custom sample driver
by modifing compatible.
- compatible = "audio-graph-card2-custom-sample";
+ compatible = "audio-graph-card2";
Sample custom driver will indicate customized print.
It is using Test-Component driver for CPU/Codec.
It can indicate more detail print of each behavior if user want to.
In such case, you need to update compatible to "xxx-nv" or "xxx-vv".
- compatible = "test-cpu";
+ compatible = "test-cpu-verbose";
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tuhmlu35.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
audio-graph-card2 has customizing support.
This means user can re-use audio-graph-card2 DT parsing, and possible
to expand to own special handling.
This patch adds Audio Graph Card2 Customize Sample Driver.
It can re-use audio-graph-card2 parsing by calling
audio_graph2_parse_of(...), and user can expand each functions by
using hooks.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v922lu3c.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds Codec2Codec support to audio-graph-card2.
It can use Codec2Codec but very simple case only for now.
It doesn't have "SWITCH" control yet, thus it start automatically
when it was probed, and can't stop, so far.
Thus it needs to be updated around widgets/routing handling,
and you need to understand that it is under experimental.
Codec has SND_SOC_DAPM_INPUT() (= IN) / SND_SOC_DAPM_OUTPUT(= OUT)
widgets in below case.
It is assuming 2channel, S32_LE format for now.
It needs to be updated, too.
It needs "codec2codec" node (= B), needs to have routing (= A),
need to indicate CPU side at links (= X).
ports@0 is for CPU side (= X), port@1 is Codec side (= Y).
It needs to have "rate" (= C)
+--+
| |<-- Codec0 <-- IN
| |--> Codec1 --> OUT
+--+
sound {
compatible = "audio-graph-card2";
(A) routing = "OUT" ,"DAI1 Playback",
"DAI0 Capture", "IN";
(X) links = <&c2c>;
(B) codec2codec {
ports {
(C) rate = <48000>;
(X) c2c: port@0 { c2cf_ep: endpoint { remote-endpoint = <&codec0_ep>; }; };
(Y) port@1 { c2cb_ep: endpoint { remote-endpoint = <&codec1_ep>; }; };
};
};
Codec {
ports {
port@0 {
bitclock-master;
frame-master;
codec0_ep: endpoint { remote-endpoint = <&c2cf_ep>; }; };
port@1 { codec1_ep: endpoint { remote-endpoint = <&c2cb_ep>; }; };
};
};
Link: https://lore.kernel.org/r/87k0xszlep.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87y26ylu4a.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
audio-graph-card2 will support DPCM/Multi/Codec2Codec,
and these will use almost same DT settings which uses
ports0 and ports1.
This patch adds asoc_graph_is_ports0() which checks
port is under port0 or not.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/875yu2n8ra.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We already have dummy-codec, dummy-platform.
But its issues are
1) we don't have dummy-cpu,
2) we can't select it via DeviceTree
3) It do nothing
Sometimes we want to have Dummy Sound Component for debugging,
for testing, for learning Framework behavior, etc, etc...
This patch adds Test-Component driver for it.
User can select CPU Component by using "test-cpu" compatible,
and can select Codec Component by using "test-codec" compatible.
It doesn't support Platform so far, but is easy to add.
We can verbose print to know its progress if user selected
xxx-verbose compatible driver.
for example,
test-cpu : silent Component, silent DAI
test-cpu-verbose-component : verbose Component, silent DAI
test-cpu-verbose-dai : silent Component, verbose DAI
test-cpu-verbose : verbose Component, verbose DAI
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/877dein8rx.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds test-component sound device YAML bindings.
It can be used for Sound Test/Debug.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/878ryyn8s4.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Referring to the note under USBH reset and clocks chapter of RM0436,
"In order to access USBH_OHCI registers it is necessary to activate the USB
clocks by enabling the PLL controlled by USBPHYC" (ck_usbo_48m).
The point is, when USBPHYC PLL is not enabled, OHCI register access
freezes the resume from STANDBY. It is the case when dual USBH is enabled,
instead of OTG + single USBH.
When OTG is probed, as ck_usbo_48m is USBO clock parent, then USBPHYC PLL
is enabled and OHCI register access is OK.
This patch adds ck_usbo_48m (provided by USBPHYC PLL) as clock of USBH
OHCI, thus USBPHYC PLL will be enabled and OHCI register access will be OK.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The STM32 SAI subblocks registers offsets are in the range
0x0004 (SAIx_CR1) to 0x0020 (SAIx_DR).
The corresponding range length is 0x20 instead of 0x1c.
Change reg property accordingly.
Fixes: 5afd65c3a0 ("ARM: dts: stm32: add sai support on stm32mp157c")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
STUSB1600 IRQ (Alert pin) is active low (open drain). Interrupts may get
lost currently, so fix the IRQ type.
Fixes: 83686162c0 ("ARM: dts: stm32: add STUSB1600 Type-C using I2C4 on stm32mp15xx-dkx")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The Seeed Odyssey-STM32MP157C board has a 20-pin DVP camera output. The
DCMI pins used on this output are defined in the pin state definition
&pinctrl/dcmi-1, AKA &dcmi_pins_b (added in mainline commit
02814a4152). Set these pins as the default
pinctrl of the DCMI peripheral in the board device tree.
The pins are not used for any other purpose, so it seems safe to assume
most users will not need to override (delete) what this patch provides.
status defaults to "disabled", so the peripheral will not be
unnecessarily started. And the users who actually intend to make use of
a camera on the DVP port will have this little part of the configuration
ready.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM,
which causes additional signal delay. At 108 MHz, this delay triggers
a sporadic issue where the first bit of RX data is not received by the
QSPI controller.
There are two options of addressing this problem, either by using the
DLYB block to compensate the extra delay, or by reducing the QSPI bus
clock frequency. The former requires calibration and that is overly
complex, so opt for the second option.
Fixes: 76045bc457 ("ARM: dts: stm32: Add QSPI NOR on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add support of stm32mp135f discovery board (part number: STM32MP135F-DK).
It embeds a STM32MP135F SOC with 512 MB of DDR3.
Several connections are available on this board:
4*USB2.0, 1*USB2.0 typeC DRD, SDcard, 2*RJ45, HDMI, Combo Wifi/BT, ...
Only SD card, uart4 (console) and watchdog IPs are enabled in this commit.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
These both functions are only used by the remoteproc_virtio.
There is no reason to expose them in the API.
Move the functions in remoteproc_virtio.c
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211001101234.4247-4-arnaud.pouliquen@foss.st.com
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210920090522.23784-10-wsa+renesas@sang-engineering.com
In this function, devm_platform_ioremap_resource_byname() should be
suitable to simplify code.
Signed-off-by: zhaoxiao <long870912@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210906071147.9095-1-long870912@gmail.com
If 'copy_dma_range_map() fails, the memory allocated for 'rvdev' will leak.
Move the 'copy_dma_range_map()' call after the device registration so
that 'rproc_rvdev_release()' can be called to free some resources.
Also, branch to the error handling path if 'copy_dma_range_map()' instead
of a direct return to avoid some other leaks.
Fixes: e0d072782c ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/e6d0dad6620da4fdf847faa903f79b735d35f262.1630755377.git.christophe.jaillet@wanadoo.fr
Go through the code base and use ice_for_each_* macros. While at it,
introduce ice_for_each_xdp_txq() macro that can be used for looping over
xdp_rings array.
Commit is not introducing any new functionality.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Under rare circumstances there might be a situation where a requirement
of having XDP Tx queue per CPU could not be fulfilled and some of the Tx
resources have to be shared between CPUs. This yields a need for placing
accesses to xdp_ring inside a critical section protected by spinlock.
These accesses happen to be in the hot path, so let's introduce the
static branch that will be triggered from the control plane when driver
could not provide Tx queue dedicated for XDP on each CPU.
Currently, the design that has been picked is to allow any number of XDP
Tx queues that is at least half of a count of CPUs that platform has.
For lower number driver will bail out with a response to user that there
were not enough Tx resources that would allow configuring XDP. The
sharing of rings is signalled via static branch enablement which in turn
indicates that lock for xdp_ring accesses needs to be taken in hot path.
Approach based on static branch has no impact on performance of a
non-fallback path. One thing that is needed to be mentioned is a fact
that the static branch will act as a global driver switch, meaning that
if one PF got out of Tx resources, then other PFs that ice driver is
servicing will suffer. However, given the fact that HW that ice driver
is handling has 1024 Tx queues per each PF, this is currently an
unlikely scenario.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
