rtnl_fill_statsinfo() is filling skb with one mandatory if_stats_msg structure.
nlmsg_put(skb, pid, seq, type, sizeof(struct if_stats_msg), flags);
But if_nlmsg_stats_size() never considered the needed storage.
This bug did not show up because alloc_skb(X) allocates skb with
extra tailroom, because of added alignments. This could very well
be changed in the future to have deterministic behavior.
Fixes: 10c9ead9f3 ("rtnetlink: add new RTM_GETSTATS message to dump link stats")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Roopa Prabhu <roopa@nvidia.com>
Acked-by: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Walleij says:
====================
RTL8366RB enhancements
This patch set is a set of reasonably mature improvements
for the RTL8366RB switch, implemented after Vladimir
challenged me to dig deeper into the switch functions.
ChangeLog v4->v5:
- Drop dubious flood control patch: these registers probably
only deal with rate limiting, we will deal with this
another time if we can figure it out.
ChangeLog -> v4:
- Rebase earlier circulated patches on the now merged
VLAN set-up cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for setting the STP state to the RTL8366RB
DSA switch. This rids the following message from the kernel on
e.g. OpenWrt:
DSA: failed to set STP state 3 (-95)
Since the RTL8366RB has one STP state register per FID with
two bit per port in each, we simply loop over all the FIDs
and set the state on all of them.
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements fast aging per-port using the special "security"
register, which will flush any learned L2 LUT entries on a port.
The vendor API just enabled setting and clearing this bit, so
we set it to age out any entries on the port and then we clear
it again.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8366RB hardware supports disabling learning per-port
so let's make use of this feature. Rename some unfortunately
named registers in the process.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Cc: Alvin Šipraga <alsi@bang-olufsen.dk>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ignored errors would result in crash.
Fixes: ede3fcf5ec ("gve: Add support for raw addressing to the rx path")
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent possible crashes when cleaning up after unsuccessful
initializations.
Fixes: 893ce44df5 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Signed-off-by: Tao Liu <xliutaox@google.com>
Signed-off-by: Catherine Sully <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qpl_map_size is rounded up to a multiple of sizeof(long), but the
number of qpls doesn't have to be.
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This applies a SND_PCI_QUIRK(...) to the TongFang PHxTxX1 barebone. This
fixes the issue of the internal Microphone not working after booting
another OS.
When booting a certain another OS this barebone keeps some coeff settings
even after a cold shutdown. These coeffs prevent the microphone detection
from working in Linux, making the Laptop think that there is always an
external microphone plugged-in and therefore preventing the use of the
internal one.
The relevant indexes and values where gathered by naively diff-ing and
reading a working and a non-working coeff dump.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211006130415.538243-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a test that validates that btf__add_btf() API is correctly copying
all the types from the source BTF into destination BTF object and
adjusts type IDs and string offsets properly.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211006051107.17921-4-andrii@kernel.org
Next patch will need to reuse BTF generation logic, which tests every
supported BTF kind, for testing btf__add_btf() APIs. So restructure
existing selftests and make it as a single subtest that uses bulk
VALIDATE_RAW_BTF() macro for raw BTF dump checking.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20211006051107.17921-3-andrii@kernel.org
Add a bulk copying api, btf__add_btf(), that speeds up and simplifies
appending entire contents of one BTF object to another one, taking care
of copying BTF type data, adjusting resulting BTF type IDs according to
their new locations in the destination BTF object, as well as copying
and deduplicating all the referenced strings and updating all the string
offsets in new BTF types as appropriate.
This API is intended to be used from tools that are generating and
otherwise manipulating BTFs generically, such as pahole. In pahole's
case, this API is useful for speeding up parallelized BTF encoding, as
it allows pahole to offload all the intricacies of BTF type copying to
libbpf and handle the parallelization aspects of the process.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Link: https://lore.kernel.org/bpf/20211006051107.17921-2-andrii@kernel.org
Instead of unconditionally performing push/pop on %rax/%rdx in case of
division/modulo, we can save a few bytes in case of destination register
being either BPF r0 (%rax) or r3 (%rdx) since the result is written in
there anyway.
Also, we do not need to copy the source to %r11 unless the source is either
%rax, %rdx or an immediate.
For example, before the patch:
22: push %rax
23: push %rdx
24: mov %rsi,%r11
27: xor %edx,%edx
29: div %r11
2c: mov %rax,%r11
2f: pop %rdx
30: pop %rax
31: mov %r11,%rax
After:
22: push %rdx
23: xor %edx,%edx
25: div %rsi
28: pop %rdx
Signed-off-by: Jie Meng <jmeng@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211002035626.2041910-1-jmeng@fb.com
Commit 94531cfcbe ("af_unix: Add unix_stream_proto for sockmap") sets
unix domain socket peer state to TCP_CLOSE in unix_shutdown. This could
happen when the local end is shutdown but the other end is not. Then,
the other end will get read or write failures which is not expected.
Fix the issue by setting the local state to shutdown.
Fixes: 94531cfcbe ("af_unix: Add unix_stream_proto for sockmap")
Reported-by: Casey Schaufler <casey@schaufler-ca.com>
Suggested-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Jiang Wang <jiang.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Casey Schaufler <casey@schaufler-ca.com>
Reviewed-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20211004232530.2377085-1-jiang.wang@bytedance.com
This adds the description for the i.MX8MM disp blk-ctrl.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a driver for the blk-ctrl blocks found in the i.MX8M* line of
SoCs. The blk-ctrl is a top-level peripheral located in the various *MIX
power domains and interacts with the GPC power controller to provide the
peripherals in the power domain access to the NoC and ensures that those
peripherals are properly reset when their respective power domain is
brought back to life.
Software needs to do different things to make the bus handshake happen
after the GPC *MIX domain is powered up and before it is powered down.
As the requirements are quite different between the various blk-ctrls
there is a callback function provided to hook in the proper sequence.
The peripheral domains are quite uniform, they handle the soft clock
enables and resets in the blk-ctrl address space and sequencing with the
upstream GPC power domains.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Our usage of runtime PM to control the hierarchy of power domains is
slightly unusual and means that powering up a domain may fail in early
system resume, as runtime PM is still disallowed at this stage.
However the system suspend/resume path takes care of powering down/up
the power domains in the order defined by the device parent/child and
power-domain provider/consumer hierarachy. So we can just runtime
resume all our power-domain devices to allow the power-up to work
properly in the resume path. System suspend will still disable all
domains as intended.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the domains with bus clocks to keep those clocks enabled
as long as the domain is active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some of the MIX domains are using clocks to drive the bus bridges. Those
must be enabled at all times, as long as the domain is powered up and
they don't have any other consumer than the power domain. Add an option
to keep the clocks attached to a domain enabled as long as the domain
is power up and only disable them after the domain is powered down.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Some of the GPCv2 power domains are nested inside each other without
visibility to lockdep at the genpd level, as they are in separate
driver instances and don't have a parent/child power-domain relationship.
Add a subclass annotation to the nested domains to let lockdep know that
it is okay to take the genpd lock in a nested fashion.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no user of anything in uuid.h in the hyperv.h. Replace it with
more appropriate types.h.
Fixes: f081bbb3fd ("hyper-v: Remove internal types from UAPI header")
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/20211001135544.1823-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
- set DRM_CONNECTOR_POLL_HPD as the connector will generate hotplug
events on its own
- do not call drm_kms_helper_hotplug_event() unless mode_config.funcs
pointer is not NULL to remove possible kernel oops.
Fixes: bc6fa8676e ("drm/bridge/lontium-lt9611uxc: move HPD notification out of IRQ handler")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210708230329.395976-1-dmitry.baryshkov@linaro.org
This driver was originally written to use the regmap abstraction with no
clear benefit. As the registers are always mmio and there is no sharing
of the region with other devices, we can safely read and write without
the locking that regmap provides.
This reduces the code size of the driver by about 25%.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210903051039.307991-1-joel@jms.id.au>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The gpio-mockup driver creates the properties that are shared between
platform and GPIO devices. Because of that, the properties may not
be removed at the proper point of time without provoking a use-after-free
as shown in the following backtrace:
refcount_t: underflow; use-after-free.
WARNING: CPU: 0 PID: 103 at lib/refcount.c:28 refcount_warn_saturate+0xd1/0x120
...
Call Trace:
kobject_put+0xdc/0xf0
software_node_notify_remove+0xa8/0xc0
device_del+0x15a/0x3e0
That's why the driver has to manage the lifetime of the software nodes
by itself.
The problem originates from the old device_add_properties() API, but
has been only revealed after the commit bd1e336aa8 ("driver core: platform:
Remove platform_device_add_properties()"). Hence, it's used as a landmark
for backporting.
Fixes: bd1e336aa8 ("driver core: platform: Remove platform_device_add_properties()")
Reported-by: Kent Gibson <warthog618@gmail.com>
Tested-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Bartosz: tweaked local variable placement]
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
The commit 15add06841 ("gpio: pca953x: add ->set_config implementation")
introduced support for bias setting. However this, due to being half-baked,
brought potential issues:
- the turning bias via disabling makes the pin floating for a while;
- once enabled, bias can't be disabled.
Fix all these by adding support for bias disabling and move the disabling
part under the corresponding conditional.
While at it, add support for default setting, since it's cheap to add.
Fixes: 15add06841 ("gpio: pca953x: add ->set_config implementation")
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding a SPI device ID table.
Fixes: 96c8395e21 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Wong Vee Khee says:
====================
net: stmmac: Turn off EEE on MAC link down
This patch series ensure PCS EEE is turned off on the event of MAC
link down.
Tested on Intel AlderLake-S (STMMAC + MaxLinear GPY211 PHY).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation enable PCS EEE feature in the event of link
up, but PCS EEE feature is not disabled on link down.
This patch makes sure PCE EEE feature is disabled on link down.
Fixes: 656ed8b015 ("net: stmmac: fix EEE init issue when paired with EEE capable PHYs")
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Energy-Efficient Ethernet(EEE) is disable from the MAC side,
we need to clear the DW_VR_MII_EEE_TRN_LPI bit of DW_VR_MII_EEE_MCTRL1
register.
Fixes: 7617af3d1a ("net: pcs: Introducing support for DWC xpcs Energy Efficient Ethernet")
Cc: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only one single SCMI Virtio device is currently supported by this driver
and it is referenced using a static global variable which is initialized
once for all during probing and nullified at virtio device removal.
Add proper SMP barriers to protect accesses to such device reference to
ensure that the initialzation state of such device is correctly observed by
all PEs at any time.
Return -EBUSY, instead of -EINVAL, and a descriptive error message if more
than one SCMI Virtio device is ever found and probed.
Link: https://lore.kernel.org/r/20210916103336.7243-3-cristian.marussi@arm.com
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Remove unneeded nested irqsave/irqrestore spinlocks.
Add also a few descriptive comments to explain better the system behaviour
at shutdown time.
Link: https://lore.kernel.org/r/20210916103336.7243-2-cristian.marussi@arm.com
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Use get_unaligned() instead of memcpy() to access potentially unaligned
memory, which, when accessed through a pointer, leads to undefined
behavior. get_unaligned() describes much better what is happening there
anyway even if memcpy() does the job.
In addition, since perf tool builds with -Werror, it would fire with:
util/intel-pt-decoder/../../../arch/x86/lib/insn.c: In function '__insn_get_emulate_prefix':
tools/include/../include/asm-generic/unaligned.h:10:15: error: packed attribute is unnecessary [-Werror=packed]
10 | const struct { type x; } __packed *__pptr = (typeof(__pptr))(ptr); \
because -Werror=packed would complain if the packed attribute would have
no effect on the layout of the structure.
In this case, that is intentional so disable the warning only for that
compilation unit.
That part is Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
No functional changes.
Fixes: 5ba1071f75 ("x86/insn, tools/x86: Fix undefined behavior due to potential unaligned accesses")
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lkml.kernel.org/r/YVSsIkj9Z29TyUjE@zn.tnic
These are unused and should be handled by drivers/clock/ti nowadays.
Note that we also drop some unused SCRM registers that are not clock
related.
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are unused and should be handled by drivers/clock/ti nowadays.
Note that we also drop some unused SCRM registers that are not clock
related.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and if devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125909.215-1-caihuoqing@baidu.com
When using single_open() for opening, single_release() should be
called, otherwise the 'op' allocated in single_open() will be leaked.
Fixes: 6e9fc17739 ("drm/nouveau/debugfs: add copy of sysfs pstate interface ported to debugfs")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210911075023.3969054-2-yangyingliang@huawei.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
When using single_open() for opening, single_release() should be
called, otherwise the 'op' allocated in single_open() will be leaked.
Fixes: 12885ecbfe ("drm/nouveau/kms/nvd9-: Add CRC support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210911075023.3969054-1-yangyingliang@huawei.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
nouveau_bo_init() is backed by ttm_bo_init() and ferries its return code
back to the caller. On failures, ttm_bo_init() invokes the provided
destructor which should de-initialize and free the memory.
Thus, when nouveau_bo_init() returns an error the gem object has already
been released and the memory freed by nouveau_bo_del_ttm().
Fixes: 019cbd4a4f ("drm/nouveau: Initialize GEM object before TTM object")
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203000220.18238-1-jcline@redhat.com
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Remove documentation associated with the removal of the DRM IRQ legacy
midlayer.
Eliminates these documentation warnings:
../drivers/gpu/drm/drm_irq.c:1: warning: 'irq helpers' not found
../drivers/gpu/drm/drm_irq.c:1: warning: no structured comments found
Fixes: c1736b9008 ("drm: IRQ midlayer is now legacy")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: dri-devel@lists.freedesktop.org
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20211005025312.20913-1-rdunlap@infradead.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The gbefb driver not only registers a driver but also the device for that
driver. This is all well and good when run on the IP32 machines that are
supported by the driver but since the driver supports building with
COMPILE_TEST we might also be building on other platforms which do not have
this hardware and will crash instantiating the driver. Add an IS_ENABLED()
check so we compile out the device registration if we don't have the Kconfig
option for the machine enabled.
Fixes: 552ccf6b25 ("video: fbdev: gbefb: add COMPILE_TEST support")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921212102.30803-1-broonie@kernel.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Configurations with both CONFIG_FB_SIMPLE=y and CONFIG_DRM_SIMPLEDRM=m
are allowed by Kconfig because the 'depends on !DRM_SIMPLEDRM' dependency
does not disallow FB_SIMPLE as long as SIMPLEDRM is not built-in. This
can however result in a build failure when cfb_fillrect() etc are then
also in loadable modules:
x86_64-linux-ld: drivers/video/fbdev/simplefb.o:(.rodata+0x1f8): undefined reference to `cfb_fillrect'
x86_64-linux-ld: drivers/video/fbdev/simplefb.o:(.rodata+0x200): undefined reference to `cfb_copyarea'
x86_64-linux-ld: drivers/video/fbdev/simplefb.o:(.rodata+0x208): undefined reference to `cfb_imageblit'
To work around this, change FB_SIMPLE to be a 'tristate' symbol,
which still allows both to be =m together, but not one of them to
be =y if the other one is =m. If a distro kernel picks this
configuration, it can be determined by local policy which of
the two modules gets loaded. The 'of_chosen' export is needed
as this is the first loadable module referencing it.
Alternatively, the Kconfig dependency could be changed to
'depends on DRM_SIMPLEDRM=n', which would forbid the configuration
with both drivers.
Fixes: 11e8f5fd22 ("drm: Add simpledrm driver")
Acked-by: Rob Herring <robh@kernel.org> # for drivers/of/
Link: https://lore.kernel.org/all/20210721151839.2484245-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch> # fbdev support
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Borislav Petkov <bp@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # v5.14+
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210928145243.1098064-1-arnd@kernel.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
