[Why/How]
Theoretically rare corner case where ceil(Y) results in rounding
up to an integer. If this happens, the 1 should be carried over to
the X value.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is a chance verified link cap can be greater than max link cap.
This causes software hang because we cannot power up PHY with link rate
that cannot handle.
The change is to guard verfieid link cap from becoming larger than max link cap
our PHy can support.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Stack variable params.backlight_ramping_override is uninitialized, so it
contains junk data
[How]
Initialize the variable to false
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Blnd, 3dlut, and shaper LUT select registers are double buffered, however
their accompanying LUT memory shutdown registers are not. As a result,
shutting down LUT memory immediately after setting a block to bypass causes
corruption as bypass only happens at next Vupdate.
[HOW]
Re-enable mem low power for CM block
Force optimization on next flip and disable LUT memory during optimization
sequence if LUT select field is then set to bypass
v2: squash in CONFIG_DRM_AMD_DC_DCN fix (Alex)
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Built-in graphics at 07:00.0 on HP EliteDesk 805 G6 doesn't work because
graphics can't get the BAR it needs. The BIOS configuration is
correct: BARs 0 and 2 both fit in the 00:08.1 bridge window.
But that 00:08.1 window covers two host bridge apertures from _CRS.
Previously we assumed this was illegal, so we clipped the window to fit
into one aperture (see 0f7e7aee2f ("PCI: Add pci_bus_clip_resource() to
clip to fit upstream window")).
pci_bus 0000:00: root bus resource [mem 0x10020200000-0x100303fffff window]
pci_bus 0000:00: root bus resource [mem 0x10030400000-0x100401fffff window]
pci 0000:00:08.1: bridge window [mem 0x10030000000-0x100401fffff 64bit pref]
pci 0000:07:00.0: reg 0x10: [mem 0x10030000000-0x1003fffffff 64bit pref]
pci 0000:07:00.0: reg 0x18: [mem 0x10040000000-0x100401fffff 64bit pref]
pci 0000:00:08.1: can't claim BAR 15 [mem 0x10030000000-0x100401fffff 64bit pref]: no compatible bridge window
pci 0000:00:08.1: [mem 0x10030000000-0x100401fffff 64bit pref] clipped to [mem 0x10030000000-0x100303fffff 64bit pref]
pci 0000:00:08.1: bridge window [mem 0x10030000000-0x100303fffff 64bit pref]
pci 0000:07:00.0: can't claim BAR 0 [mem 0x10030000000-0x1003fffffff 64bit pref]: no compatible bridge window
pci 0000:07:00.0: can't claim BAR 2 [mem 0x10040000000-0x100401fffff 64bit pref]: no compatible bridge window
However, the host bridge apertures are contiguous, so there's no need to
clip in this case. Coalesce contiguous apertures so we can allocate from
the entire contiguous region.
Previous commit 65db04053e ("PCI: Coalesce host bridge contiguous
apertures") was similar but sorted the apertures, and Guenter Roeck
reported a regression in ppc:sam460ex qemu emulation from nvme; see
https://lore.kernel.org/all/20210709231529.GA3270116@roeck-us.net/
[bhelgaas: commit log]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=212013
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20210713125007.1260304-1-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Remove insecure NTLMv1 authentication.
Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Cc: Ralph Böhme <slow@samba.org>
Reviewed-by: Tom Talpey <tom@talpey.com>
Acked-by: Steve French <smfrench@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
We have a unit test that invokes an XDP program with 1m different
inputs, aka 1m BPF_PROG_RUN syscalls. We run this test concurrently
with slight variations in how we generated the input.
Since commit f23c4b3924 ("bpf: Start using the BPF dispatcher in BPF_TEST_RUN")
the unit test has slowed down significantly. Digging deeper reveals that
the concurrent tests are serialised in the kernel on the XDP dispatcher.
This is a global resource that is protected by a mutex, on which we contend.
Fix this by not calling into the XDP dispatcher if we only want to perform
a single run of the BPF program.
See: https://lore.kernel.org/bpf/CACAyw9_y4QumOW35qpgTbLsJ532uGq-kVW-VESJzGyiZkypnvw@mail.gmail.com/
Signed-off-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210928093100.27124-1-lmb@cloudflare.com
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Class based instantiation has already been removed for other controllers
and it makes absolutely sense to do it for this one too.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Acked-by: Ingmar Klein <ingmar.klein@kontron.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Signed-off-by: zhaoxiao <long870912@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We want to enable the interrupts _before_ starting the transfer because
it is good programming style and also the proposed order in the R-Car
manual. There is no difference in practice because it doesn't matter in
which order both conditions appear if we wait for both to happen.
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The PHY ownership release->AUX PW disable steps during a modeset
disable->PHY disconnect sequence can hang the system if the PHY
disconnect happens after disabling the PHY's PLL. The spec doesn't
require a specific order for these two steps, so this issue is still
being root caused by HW/FW teams. Until that is found, let's make
sure the disconnect happens before the PLL is disabled, and do this on
all platforms for consistency.
v2: Add a TODO comment to remove the w/a once the issue is root
caused/fixed. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-7-imre.deak@intel.com
After the previous patch the driver holds a power domain blocking
TC-cold whenever the port is locked, so we can remove the extra blocking
around the lock/unlock sequence.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-13-imre.deak@intel.com
So far TC-cold was blocked only for the duration of TypeC mode resets.
The DP-alt and legacy modes require TC-cold to be blocked also whenever
the port is in use (AUX transfers, enable modeset), and this was ensured
by the held PHY ownership flag. On ADL-P this doesn't work, since the
PHY ownership flag is in a register backed by the PW#2 power well.
Whenever this power well is disabled the ownership flag is cleared by
the HW under the driver.
The only way to cleanly release and re-acquire the PHY ownership flag
and also allow for power saving (by disabling the display power wells
and reaching DC5/6 states) is to hold the TC-cold blocking power domains
while the PHY is connected and disconnect/reconnect the PHY on-demand
around AUX transfers and modeset enable/disables. Let's do that,
disconnecting a PHY with a 1 sec delay after it becomes idle. For
consistency do this on all platforms and TypeC modes.
v2: Add tc_mode!=disconnected and phy_is_owned asserts to
__intel_tc_port_lock().
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-6-imre.deak@intel.com
While a TypeC port mode is locked a DISPLAY_CORE power domain reference
is held, which implies a runtime PM ref. By removing the ICL !legacy
port special casing, a TC_COLD_OFF power domain reference will be taken
for such ports, which also translates to a runtime PM ref on that
platform. A follow-up change will stop holding the DISPLAY_CORE power
domain while the port is locked.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-11-imre.deak@intel.com
For the ADL-P TBT mode the spec doesn't require blocking TC-cold by
using the legacy AUX power domain. To avoid the timeouts that this would
cause during PHY disconnect/reconnect sequences (which will be more
frequent after a follow-up change) use the TC_COLD_OFF power domain in
TBT mode on all platforms. On TGL this power domain blocks TC-cold via a
PUNIT command, while on other platforms the domain just takes a runtime
PM reference.
If the HPD live status indicates that the port mode needs to be reset
- for instance after switching from TBT to a DP-alt sink - still take
the AUX domain, since the IOM firmware handshake requires this.
v2: Rebased on v2 of the previous patch.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-5-imre.deak@intel.com
A follow-up change will select the TC-cold blocking power domain based
on the TypeC mode, prepare for that here.
Also bring intel_tc_cold_requires_aux_pw() earlier to its logical place
for readability.
No functional change.
v2: Add code comment about IOM reg accesses in TCCOLD. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-4-imre.deak@intel.com
A follow-up change will start to disconnect/re-connect PHYs around AUX
transfers and modeset enable/disables. To prepare for that add a new
TypeC PHY disconnected mode, to help tracking the TC-cold blocking power
domain status (no power domain in disconnected state, mode dependent
power domain in connected state).
v2: Move the !disconnected mode and phy-owned asserts in
__intel_tc_port_lock() later in the patchset, when the asserts will
hold. (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-3-imre.deak@intel.com
A follow-up patch will disconnect/reconnect PHYs around AUX transfers
and modeset enable/disables. To prepare for that and make things
consistent for all TypeC modes stop connecting the PHY in legacy mode
without a sink being connected. This was done before since in legacy
mode the PHY is dedicated to display usage, so there was no point in
disconnecting it. However after the follow-up changes the TC-cold
blocking power domains will be held as long as the PHY is in the
connected state, so we'll need to disconnect/re-connect the PHY in all
TypeC modes to allow for power saving.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-7-imre.deak@intel.com
Instead of directly accessing the TypeC port internal struct members,
add/use helpers to retrieve the corresponding properties.
No functional change.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-6-imre.deak@intel.com
On ADL-P the PHY ready/complete flag is always set even in TBT-alt mode.
To avoid taking the PHY ownership and the following spurious "PHY sudden
disconnect" messages on this platform when connecting the PHY in TBT
mode, check if there is any DP-alt or legacy sink connected before
taking the ownership.
v2: (Jose)
- Fix debug message clarifying that a TBT sink can be connected.
- Add comments describing the PHY complete HW flag semantic differences
between adl-p and other platforms.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-2-imre.deak@intel.com
Waiting for the PHY complete flag to clear when releasing the PHY
ownership was add in
commit ddec362724 ("drm/i915: Wait for TypeC PHY complete flag to clear in safe mode")
This isn't required by the spec, the vague idea was to make the
handshake with the firmware more robust, without actual evidence for
when it would be needed. Checking this again, the flag doesn't clear on
ICL until after the PHY's PLL is disabled and the flag is permanently
set on ADL-P. To avoid the spurious timeout messages in dmesg, just
remove this wait.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-4-imre.deak@intel.com
On ADL-P the PHY ready (aka status complete on other platforms) flag is
always set, besides when a DP-alt, legacy sink is connected also when a
TBT sink is connected or nothing is connected. So assume the PHY to be
connected when both the TBT live status and PHY ready flags are set.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-3-imre.deak@intel.com
Atm during driver loading and system resume TypeC ports are accessed
before their HW/SW state is synced. Move the TypeC port sanitization to
the encoder's sync_state hook to fix this.
v2: Handle the encoder disabled case in gen11_dsi_sync_state() as well
(Jose, Jani)
Fixes: f9e76a6e68 ("drm/i915: Add an encoder hook to sanitize its state during init/resume")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-1-imre.deak@intel.com
This adds force_prevent_wake which can be used to force a certain state
while interacting with force_suspend.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds force_suspend which can be used to force the controller into
suspend/resume state.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cleanup code uses while (cpu++ < cpu_cnt) for closing fds, which means
it starts iterating from 1 for closing fds. If the first fd is -1, it
skips over it and closes garbage fds (typically zero) in the remaining
array. This leads to test failures for future tests when they end up
storing fd 0 (as the slot becomes free due to close(0)) in ldimm64's BTF
fd, ending up trying to match module BTF id with vmlinux.
This was observed as spurious CI failure for the ksym_module_libbpf and
module_attach tests. The test ends up closing fd 0 and breaking libbpf's
assumption that module BTF fd will always be > 0, which leads to the
kernel thinking that we are pointing to a BTF ID in vmlinux BTF.
Fixes: 025bd7c753 (selftests/bpf: Add test for bpf_get_branch_snapshot)
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210927145941.1383001-12-memxor@gmail.com
The original change works as intended, but Andy pointed in [0] that now
userspace could re-enable RPM via sysfs, even though we explicitly want
to disable it. So effectively revert the original patch, just with small
improvements:
- Calls to pm_runtime_allow()/pm_runtime_forbid() don't have to be
balanced, so we can remove the call to pm_runtime_forbid() in
i801_remove().
- priv->acpi_reserved is accessed after i801_acpi_remove(), and according
to Robert [1] the custom handler can't run any longer. Therefore we
don't have to take priv->acpi_lock.
[0] https://www.spinics.net/lists/linux-i2c/msg52730.html
[1] https://lore.kernel.org/linux-acpi/BYAPR11MB32561D19A0FD9AB93E2B1E5287D39@BYAPR11MB3256.namprd11.prod.outlook.com/T/#t
Fixes: 4e60d5dd10 ("i2c: i801: Improve disabling runtime pm")
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
As pointed out by Andy in [0] using a local mutex here isn't strictly
wrong but not sufficient. We should hold the PCI rescan lock for P2SB
operations.
[0] https://www.spinics.net/lists/linux-i2c/msg52717.html
Fixes: 1a987c69ce ("i2c: i801: make p2sb_spinlock a mutex")
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The return value of i801_add_mux() isn't used, so let's change it to void.
In addition remove the not needed cast to struct gpiod_lookup.
GPIO_LOOKUP() uses GPIO_LOOKUP_IDX() that includes this cast.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
By using ACPI_HANDLE() the handler argument can be retrieved directly.
Both address space handler functions check the handler argument and
return an error if it's NULL. This allows to further simplify the code.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
do_pci_enable_device() takes care that PCI_COMMAND_INTX_DISABLE
is cleared if a legacy interrupt is used.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Replace the ugly cast of the return_value pointer with proper usage.
In addition use dmi_match() instead of open-coding it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Using struct pci_platform_pm_ops for ACPI adds unnecessary
indirection to the interactions between the PCI core and ACPI PM,
which is also subject to retpolines.
Moreover, it is not particularly clear from the current code that,
as far as PCI PM is concerned, "platform" really means just ACPI
except for the special casess when Intel MID PCI PM is used or when
ACPI support is disabled (through the kernel config or command line,
or because there are no usable ACPI tables on the system).
To address the above, rework the PCI PM code to invoke ACPI PM
functions directly as needed and drop the acpi_pci_platform_pm
object that is not necessary any more.
Accordingly, update some of the ACPI PM functions in question to do
extra checks in case the ACPI support is disabled (which previously
was taken care of by avoiding to set the pci_platform_ops pointer
in those cases).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Update Altera Pio Driver maintainer's email from <joyce.ooi@intel.com> to <mun.yew.tham@intel.com>
Signed-off-by: Mun Yew Tham <mun.yew.tham@intel.com>
Acked-by: Joyce Ooi <joyce.ooi@intel.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Per gpio_chip interface, error shall be proparated to the caller.
Attempt to silent diagnostics by returning zero (as written in the
comment) is plain wrong, because the zero return can be interpreted by
the caller as the gpio value.
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Certain kernel symbols are purposely hidden from kallsyms. The function
is_ignored_symbol() from scripts/kallsyms.c decides if a symbol should
be hidden or not.
The perf test "vmlinux symtab matches kallsyms" fails in case perf finds
some of the hidden symbols in its machine image and can't match them to
kallsyms.
Let's add a filter to check if a symbol not found isn't one of these
before failing the test.
The function is_ignored_symbol() has been copied from scripts/kallsyms.c
and needs to be updated along with the original.
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
LPU-Reference: 20210922152706.23655-1-mpetlan@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In Kconfig, like Python, you can enclose a string by double-quotes or
single-quotes. So, both "foo" and 'foo' are allowed.
The variable, "str", is used to remember whether the string started with
a double-quote or a single-quote because open/closing quotation marks
must match.
The name "str" is too generic to understand the intent. Rename it to
"open_quote", which is easier to understand. The type should be 'char'.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Boris Kolpackov <boris@codesynthesis.com>
The variables, "ts" and "i", are used locally in the action of
the [ \t]+ pattern in the <HELP> start state.
Define them where they are used.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
For a metric like:
CONST if expr else CONST
if the values of CONST are identical then expr doesn't need evaluating,
and events, in order to compute a result.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: John Garry <john.garry@huawei.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Clarke <pc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandeep Dasgupta <sdasgup@google.com>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20210923074616.674826-14-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
For a metric like:
EVENT1 if #smt_on else EVENT2
currently EVENT1 and EVENT2 will be measured and then when the metric is
reported EVENT1 or EVENT2 will be printed depending on the value from
smt_on() during the expr parsing. Computing both events is unnecessary and
can lead to multiplexing as discussed in this thread:
https://lore.kernel.org/lkml/20201110100346.2527031-1-irogers@google.com/
If the input is constant to certain operators like:
IDS1 if CONST else IDS2
then the result will be either IDS1 or IDS2 depending on CONST (which
may be evaluated from an entire expression), and so IDS1 or IDS2 may
be discarded avoiding events from being programmed.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: John Garry <john.garry@huawei.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Clarke <pc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandeep Dasgupta <sdasgup@google.com>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20210923074616.674826-13-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When we're computing ID values, if we have constant values then compute
the constant result. For example:
1 + 2
Previously .val would be set to BOTTOM by union_expr, meaning that
all values are possible. With this change .val is set to 3.
Later changes will use the constant values to hopefully eliminate ID
values that don't need to be computed.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: John Garry <john.garry@huawei.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Clarke <pc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandeep Dasgupta <sdasgup@google.com>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20210923074616.674826-12-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add a new option to parsing that the set of IDs being used should be
computed, this means every action needs to handle the compute_ids and
regular case. This means actions yield a new ids type is a set of ids or
the value being computed. Use the compute_ids case to replace find IDs
parsing.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: John Garry <john.garry@huawei.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Clarke <pc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandeep Dasgupta <sdasgup@google.com>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20210923074616.674826-11-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
A metric may be a constant value, for example, some SMT metrics are
constant 0 if #smt_on is 0. If we eliminate all the events then there is
no printing. Fix this by forcing metrics like this to have a
duration_time tool event, previously the metric would fail when parsing
the events with a parse error.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: John Garry <john.garry@huawei.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Clarke <pc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandeep Dasgupta <sdasgup@google.com>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20210923074616.674826-10-irogers@google.com
[ Reflow one __parse_events() call so that a ternary operation gets in a single line ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add utilities to new/free an ids hashmap, as well as to union. Add
testing of the union. Unioning hashmaps will be used when parsing the
metric, if a value is known then the hashmap is unnecessary, otherwise
we need to union together all the event ids to compute their values for
reporting.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: John Garry <john.garry@huawei.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Clarke <pc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandeep Dasgupta <sdasgup@google.com>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20210923074616.674826-9-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
A later change will remove the notion of other, rename the function to
expr__find_ids as this is what it populates.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: John Garry <john.garry@huawei.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Clarke <pc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandeep Dasgupta <sdasgup@google.com>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20210923074616.674826-8-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
No functional change, just modifying whitespace. This creates additional
space for adding logic to actions in later changes.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: John Garry <john.garry@huawei.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Clarke <pc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandeep Dasgupta <sdasgup@google.com>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20210923074616.674826-7-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
No functional change, switch the operators to use macros so that
additional complexity for constants can be added in a later change.
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: John Garry <john.garry@huawei.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jin Yao <yao.jin@linux.intel.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Clarke <pc@us.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sandeep Dasgupta <sdasgup@google.com>
Cc: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/r/20210923074616.674826-6-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
