Resetting/stopping an itimer eventually leads to it being reprogrammed
with an actual "0" value. As a result the itimer expires on the next
tick, triggering an unexpected signal.
To fix this, make sure that
struct signal_struct::it[CPUCLOCK_PROF/VIRT]::expires is set to 0 when
setitimer() passes a 0 it_value, indicating that the timer must stop.
Fixes: 406dd42bd1 ("posix-cpu-timers: Force next expiration recalc after itimer reset")
Reported-by: Victor Stinner <vstinner@redhat.com>
Reported-by: Chris Hixon <linux-kernel-bugs@hixontech.com>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20210913145332.232023-1-frederic@kernel.org
backlight.h documents "struct backlight_ops->get_brightness()" to return
a negative errno on failure.
So far these errors have not been handled in the backlight core.
This leads to negative values being exposed through sysfs although only
positive values are documented to be reported.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Switch from the "_ro" clock op variants to the mutable ones for all
video clocks. This will allow the VPU driver to change the clocks as
needed for the different video output modes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210713232510.3057750-6-martin.blumenstingl@googlemail.com
Add the reg_sequence to initialize the HDMI PLL with the settings for
a video mode that doesn't require PLL internal clock doubling. These
settings are taken from the 3.10 vendor kernel's driver for the 2970MHz
PLL setting used for the 1080P video mode. This puts the PLL into a
defined state and the Linux kernel can take over.
While not all bits for this PLL are implemented using these "defaults"
and then applying M, N and FRAC seems to work fine.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210713232510.3057750-5-martin.blumenstingl@googlemail.com
The 3.10 vendor kernel uses only specific HDMI PLL M/N parameter
combinations. The PLL won't lock for values smaller than 50 if the
internal doubling (which is yet unknown how to use it) is disabled.
However, when this doubling is enabled then the values smaller than 50
will lock just fine. The only restriction for values greater than 50 is
that the resulting frequency must not exceed the 3.0GHz limit.
These values are taken from the endlessm 3.10 kernel which includes
additional M/N combinations for some VESA and 75Hz display modes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210713232510.3057750-4-martin.blumenstingl@googlemail.com
HHI_VID_DIVIDER_CNTL[11] must be enabled for the video clock tree to
work. This bit is described as "LVDS_CLK_EN". It is not 100% clear where
this bit has to be placed in the hierarchy. But since the "LVDS_OUT" of
the HDMI PLL uses it's own set of registers it's more likely that this
"LVDS_CLK_EN" bit actually enables the input of the "hdmi_pll_lvds_out"
clock to the "vid_pll_in_sel" tree.
Add a gate definition for this bit (which will not be exported) so that
the kernel can manage all required bits to enable and disable the video
clocks.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210713232510.3057750-3-martin.blumenstingl@googlemail.com
Use CLK_SET_RATE_NO_REPARENT for the vclk{,2}_in_sel clocks. The only
parent which is actually used is vid_pll_final_div. This should be set
using assigned-clock-parents in the .dts rather than removing some
"unwanted" clock parents from the clock driver.
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210713232510.3057750-2-martin.blumenstingl@googlemail.com
Setting the video clocks requires fine-tuned adjustments of various
video clocks. Export the required ones to allow changing the video clock
for the CVBS and HDMI outputs at runtime.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20210713232510.3057750-7-martin.blumenstingl@googlemail.com
To be able to compile the kernel with LTO, the assembler macros cannot
be declared in the global scope, or the compiler will complain about
redefined macros.
Update the code so that macros are defined then undefined when they are
used.
Note that virt support was added in 2.24 and xpa in 2.25. So we still
need the TOOLCHAIN defines for them.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The Framebuffer CONFIG_FB needs to be explicitly selected or we
don't get any framebuffer anymore. DRM has stopped to select FB
after commit f611b1e762 ("drm: Avoid circular
dependencies for CONFIG_FB") because of circular dependency. So
we should enable it in the default config file, otherwise there
is no display before Xorg.
Signed-off-by: Wang Haojun <wanghaojun@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
mach/loongson64 fails to build when the FPU support is disabled:
arch/mips/loongson64/cop2-ex.c:45:15: error: implicit declaration of function ‘__is_fpu_owner’; did you mean ‘is_fpu_owner’? [-Werror=implicit-function-declaration]
arch/mips/loongson64/cop2-ex.c:98:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:99:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:131:43: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:137:38: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:203:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:219:30: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:283:38: error: ‘struct thread_struct’ has no member named ‘fpu’
arch/mips/loongson64/cop2-ex.c:301:38: error: ‘struct thread_struct’ has no member named ‘fpu’
Fixes: ef2f826c8f ("MIPS: Loongson-3: Enable the COP2 usage")
Suggested-by: Huacai Chen <chenhuacai@kernel.org>
Reviewed-by: Huacai Chen <chenhuacai@kernel.org>
Reported-by: k2ci robot <kernel-bot@kylinos.cn>
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Avoid having indirect calls and use a normal function which returns the
proper MSR address based on ->smca setting.
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20210922165101.18951-4-bp@alien8.de
Get rid of the indirect function pointer and use flags settings instead
to steer execution.
Now that it is not an indirect call any longer, drop the instrumentation
annotation for objtool too.
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20210922165101.18951-3-bp@alien8.de
Turn it into a normal function which calls an AMD- or Intel-specific
variant depending on the CPU it runs on.
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20210922165101.18951-2-bp@alien8.de
Fix the missing return code polarity in save_xstate_epilog().
[ bp: Massage, use the right commit in the Fixes: tag ]
Fixes: 2af07f3a6e ("x86/fpu/signal: Change return type of copy_fpregs_to_sigframe() helpers to boolean")
Reported-by: Remi Duraffort <remi.duraffort@linaro.org>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1461
Link: https://lkml.kernel.org/r/20210922200901.1823741-1-anders.roxell@linaro.org
Some CP2102 do not support event-insertion mode but return no error when
attempting to enable it.
This means that any event escape characters in the input stream will not
be escaped by the device and consequently regular data may be
interpreted as escape sequences and be removed from the stream by the
driver.
The reporter's device has batch number DCL00X etched into it and as
discovered by the SHA2017 Badge team, counterfeit devices with that
marking can be detected by sending malformed vendor requests. [1][2]
Tests confirm that the possibly counterfeit CP2102 returns a single byte
in response to a malformed two-byte part-number request, while an
original CP2102 returns two bytes. Assume that every CP2102 that behaves
this way also does not support event-insertion mode (e.g. cannot report
parity errors).
[1] https://mobile.twitter.com/sha2017badge/status/1167902087289532418
[2] https://hackaday.com/2017/08/14/hands-on-with-the-shacamp-2017-badge/#comment-3903376
Reported-by: Malte Di Donato <malte@neo-soft.org>
Tested-by: Malte Di Donato <malte@neo-soft.org>
Fixes: a7207e9835 ("USB: serial: cp210x: add support for line-status events")
Cc: stable@vger.kernel.org # 5.9
Link: https://lore.kernel.org/r/20210922113100.20888-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
As stated in the comment above xfrm_nlmsg_multicast(), rcu read lock must
be held before calling this function.
Reported-by: syzbot+3d9866419b4aa8f985d6@syzkaller.appspotmail.com
Fixes: 703b94b93c19 ("xfrm: notify default policy on update")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
xfrm4_tunnel.c hasn't use any macro or function declared in mutex.h and ip.h
Thus, these files can be removed from xfrm4_tunnel.c safely without affecting
the compilation of the net module.
Signed-off-by: Mianhan Liu <liumh1@shanghaitech.edu.cn>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch adds driver support for the zynqmp modepin GPIO controller.
GPIO modepin driver set and get the value and status of the PS_MODE pin,
based on device-tree pin configuration. These four mode pins are
configurable as input/output. The mode pin has a control register, which
have lower four-bits [0:3] are configurable as input/output, next four-bits
can be used for reading the data as input[4:7], and next setting the
output pin state output[8:11]. By default value of mode pin register is 0.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
This patch adds DT binding document for zynqmp modepin GPIO controller.
Modepin GPIO controller has four GPIO pins which can be configurable
as input or output.
Modepin driver is a bridge between the peripheral driver and GPIO pins.
It has set and get APIs for accessing GPIO pins, based on the device-tree
entry of reset-gpio property in the peripheral driver, every pin can be
configured as input/output and trigger GPIO pin.
For more information please refer zynqMp TRM link:
Link: https://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf
Chapter 2: Signals, Interfaces, and Pins
Table 2-2: Clock, Reset, and Configuration Pins - PS_MODE
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Add Xilinx ZynqMP firmware MMIO APIs support to set and get PS_MODE
pins value and status. These APIs create an interface path between
mode pin controller driver and low-level API to access GPIO pins.
Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Embed struct drm_device in struct drm_psb_private. Replace the use
of dev_private by an upcast operation. Switch to managed release of
struct drm_psb_private.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210920141051.30988-4-tzimmermann@suse.de
Replace most references to struct drm_device.dev_private with the new
helper function to_drm_psb_private(). The only references left are in
assignments and the helper itself.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210920141051.30988-2-tzimmermann@suse.de
The new framing mode causes the user space regression, because
the alsa-lib code does not initialize the reserved space in
the params structure when the device is opened.
This change adds SNDRV_RAWMIDI_IOCTL_USER_PVERSION like we
do for the PCM interface for the protocol acknowledgment.
Cc: David Henningsson <coding@diwic.se>
Cc: <stable@vger.kernel.org>
Fixes: 08fdced60c ("ALSA: rawmidi: Add framing mode")
BugLink: https://github.com/alsa-project/alsa-lib/issues/178
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20210920171850.154186-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace arch_phys_wc_add() and arch_io_reserve_memtype_wc() with
the rsp managed functions. Allows for removing the cleanup code
for memory management
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210916181601.9146-5-tzimmermann@suse.de
Replace arch_phys_wc_add() and arch_io_reserve_memtype_wc() with
the rsp managed functions. Allows for removing the cleanup code
for memory management
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210916181601.9146-4-tzimmermann@suse.de
Add devm_arch_io_reserve_memtype_wc() as managed wrapper around
arch_io_reserve_memtype_wc(). Useful for several graphics drivers
that set framebuffer memory to write combining.
v2:
* fix typo in commit description
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210916181601.9146-3-tzimmermann@suse.de
Add devm_arch_phys_wc_add() as managed wrapper around arch_phys_wc_add().
Useful for several graphics drivers that set framebuffer memory to write
combining.
v2:
* fix typo in commit description
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210916181601.9146-2-tzimmermann@suse.de
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and if devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210922125954.533-1-caihuoqing@baidu.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and if devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210922125212.95-3-caihuoqing@baidu.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and if devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210922125212.95-2-caihuoqing@baidu.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use LOOKUP_NO_SYMLINKS flags for default lookup to prohibit the middle of
symlink component lookup and remove follow symlinks parameter support.
We re-implement it as reparse point later.
Test result:
smbclient -Ulinkinjeon%1234 //172.30.1.42/share -c
"get hacked/passwd passwd"
NT_STATUS_OBJECT_NAME_NOT_FOUND opening remote file \hacked\passwd
Cc: Ralph Böhme <slow@samba.org>
Cc: Steve French <smfrench@gmail.com>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
The SSI 1328 is a NAS box running a SL3516 SoC.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The edimax NS2502 is a NAS box running a SL3516 SoC.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When second smb2 pdu has invalid protocol id, ksmbd doesn't detect it
and allow to process smb2 request. This patch add the check it in
ksmbd_verify_smb_message() and don't use protocol id of smb2 request as
protocol id of response.
Reviewed-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Reviewed-by: Ralph Böhme <slow@samba.org>
Reported-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Commit f8ade8dddb ("xsurf100: drop include of lib8390.c") accidentally
changed init/main.c. Revert that part.
Fixes: f8ade8dddb ("xsurf100: drop include of lib8390.c")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Konrad's new job role is putting a serious cramp on him
being a responsive maintainer and as such he is handing off
the reins to Juergen, Roger, and Stefano.
Thank you!
Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Konrad's new job role is putting a serious cramp on him
being a responsive maintainer and as such he is handing off
the reins to Christoph Hellwig.
Thank you!
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ley Foon has left Intel and will no longer be able to maintain NIOS2.
Update the MAINTAINER's entry to Dinh Nguyen.
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>