Due to duplicate reset flags, CQP commands are processed during reset.
This leads CQP failures such as below:
irdma0: [Delete Local MAC Entry Cmd Error][op_code=49] status=-27 waiting=1 completion_err=0 maj=0x0 min=0x0
Remove the redundant flag and set the correct reset flag so CPQ is paused
during reset
Fixes: 8498a30e1b ("RDMA/irdma: Register auxiliary driver and implement private channel OPs")
Link: https://lore.kernel.org/r/20210916191222.824-2-shiraz.saleem@intel.com
Reported-by: LiLiang <liali@redhat.com>
Signed-off-by: Sindhu Devale <sindhu.devale@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
When VF is configured with default vlan, HW strips the vlan from the
packet and driver receives it in Rx completion. VLAN needs to be reported
for UD work completion only if the vlan is configured on the host. Add a
check for valid vlan in the UD receive path.
Link: https://lore.kernel.org/r/1631709163-2287-12-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
FRMR WQE requires to provide the log2 value of the PBL and page size. Use
the standard ilog2() to calculate the log2 value
Link: https://lore.kernel.org/r/1631709163-2287-11-git-send-email-selvin.xavier@broadcom.com
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Use GFP_KERNEL instead of GFP_ATOMIC while allocating control path
structures which will be only called from non atomic context
Link: https://lore.kernel.org/r/1631709163-2287-10-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
When the FRMR is allocated with single page, driver is attempting to
create a level 0 HWQ and not allocating any page because the nopte field
is set. This causes the crash during post_send as the pbl is not
populated.
To avoid this crash, check for the nopte bit during HWQ creation with
single page and create a level 1 page table and populate the pbl address
correctly.
Link: https://lore.kernel.org/r/1631709163-2287-9-git-send-email-selvin.xavier@broadcom.com
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fill the missing parameters for the FW command while querying SRQ.
Fixes: 37cb11acf1 ("RDMA/bnxt_re: Add SRQ support for Broadcom adapters")
Link: https://lore.kernel.org/r/1631709163-2287-8-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
HW can support multiple page sizes. Enable bits for enabling sizes from 4k
to 1G by reporting page_size_cap.
Link: https://lore.kernel.org/r/1631709163-2287-6-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Driver has 1ms delay between the polling for atomic command completion.
Polling immediately after issuing command usually doesn't report any
completions. So all commands in the blocking path needs two iterations. So
effectively 1ms spend on each command. HW requires much lesser time for
each command. So reduce the delay to 1us and increase the iteration count
to wait for the same time.
Link: https://lore.kernel.org/r/1631709163-2287-5-git-send-email-selvin.xavier@broadcom.com
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Use separate buffers for the request and response data. Eventhough the
response data is not used, providing the correct length is appropriate.
Link: https://lore.kernel.org/r/1631709163-2287-4-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Update a statistics counter name as the interface structure got updated.
Fixes: 9d6b648c31 ("bnxt_en: Update firmware interface spec to 1.10.1.65.")
Link: https://lore.kernel.org/r/1631709163-2287-3-git-send-email-selvin.xavier@broadcom.com
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Implement extended statistics counters for newer adapters. Check if the FW
support for this command and issue the FW command only if is
supported. Includes code re-organization to handle extended stats. Also,
add AH and PD software counters.
Link: https://lore.kernel.org/r/1631709163-2287-2-git-send-email-selvin.xavier@broadcom.com
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
As discussed in the patch ("dt-bindings: drm/panel-simple: Introduce
generic eDP panels") we can actually support probing eDP panels at
runtime instead of hardcoding what panel is connected. Add support to
the panel-edp driver for this.
We'll implement a solution like this:
* We'll read in two delays from the device tree that are used for
powering up the panel the initial time (to read the EDID).
* In the EDID we can find a 32-bit ID that identifies what panel we've
found. From this ID we can look up the full set of delays.
After this change we'll still need to add per-panel delays into the
panel-simple driver but we will no longer need to specify exactly
which panel is connected to which board in the device tree. Nicely,
any panels that are only supported this way also don't need to
hardcode mode data since it's guaranteed that we can get that through
the EDID.
This patch will seed the ID-to-delay table with a few panels that I
have access to, many of which are on sc7180-trogdor devices.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.15.Id9c96cba4eba3e5ee519bfb09cd64b39f2490293@changeid
The arm,vexpress-juno binding is missing 'ranges', 'arm,vexpress,site', and
'arm,hbi' properties. Add these and and restrict additional properties to
be nodes only.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210819184239.1192395-3-robh@kernel.org
Commit 9d0a36ddcc ("arm64: dts: fvp/juno: Fix bus node names") changed
'motherboard' to 'motherboard-bus', but didn't update the schema. In the
mean time, the simple-bus schema started requiring child nodes to have a
unit-address. Update the schema to address both of these issues.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210819184239.1192395-2-robh@kernel.org
While cleaning up the descriptions of the delay for eDP panels I
realized that we'd have a bug if any panels need the
"prepare_to_enable" but HPD handling isn't happening in the panel
driver. Let's put in a stopgap to at least make us not violate
timings. This is not perfectly optimal but trying to do better is
hard. At the moment only 2 panels specify this delay and only 30 ms is
at stake. These panels are also currently hooked up with "hpd-gpios"
so effectively this "fix" is just a theoretical fix and won't actually
do anything for any devices currently supported in mainline.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.13.Ia8288d36df4b12770af59ae3ff73ef7e08fb4e2e@changeid
Now that the delays are named / described with eDP-centric names, it
becomes clear that we should really specify the "hpd_reliable" and
"hpd_absent" separately without taking the other into account. Let's
fix it.
This should be a no-op change and just adjust how we specify
things. The actual delays should be the same before and after for the
one panel that currently species both "hpd_reliable" and "hpd_absent".
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.12.I2522235fca3aa6790ede0bf22a93d79a1f694e6b@changeid
Now that the eDP panel driver only handles eDP panels we can make
better sense of the delays here. Let's describe them in terms of the
standard eDP timing diagram from the eDP spec.
As part of this, it becomes pretty clear that some eDP panels have too
long of a "hpd_reliable_delay". This used to be the "prepare"
delay. It's the fixed delay that we do in the panel driver after
powering on our panel before we look at the HPD signal. To understand
this better, first realize that there could be 3 paths we follow
depending on how HPD is hooked up. Let's walk through them:
1. HPD is handled by the eDP controller driver. Until "recently"
(commit 48834e6084 ("drm/panel-simple: Support hpd-gpios for
delaying prepare()") in May 2020) this was the only supported
way. This is supposed to be when the controller driver gets HPD
straight to a dedicated pin. In this case the controller driver
should be waiting for HPD in its pre_enable() routine which should
be called right after the panel's prepare() function is
called. That means that the old "prepare" delay was only needed as
a delay after powering the panel but before looking at HPD.
2. HPD is handled via hpd-gpios in the panel. This is much like #1 but
much easier to follow since all the handling is in the panel
driver.
3. The no-hpd case. This is also easy to follow.
In any case, even though it seems like some old panel data was using
this incorrectly, let's not touch the old data structures but we'll
add a note indicating that something seems off.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.11.I2d798dd015332661c5895ef744bc8ec5cd2e06ca@changeid
In the case where we can read an EDID for a panel the only part of the
panel description that can't be found directly from the EDID is the
description of the delays. Let's break the delay structure out so that
we can specify just the delays for panels that are detected by EDID.
This is simple code motion. No functional change is intended.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.10.I24f3646dd09954958645cc05c538909f169bf362@changeid
All of the "HPD" handling added to panel-simple recently was for eDP
panels. Remove it from panel-simple now that panel-edp handles eDP
panels. The "prepare_to_enable" delay only makes sense in the context
of HPD, so remove it too. No non-eDP panels used it anyway.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.9.I77d7a48df0a6585ef2cc2ff140fbe8f236a9a9f7@changeid
Not all panels in panel-simple were marked what type of panel they
were. I searched through ARM/ARM64 Chromebooks or Chromebook-related
reference boards that I was aware of and found some panels that needed
to be moved. I also skimmed for panels that had no mode and were "big"
since it's quite rare to see a small eDP panel. Here's what I found:
* auo,b101ean01 - rk3288-veyron-minnie
* auo,b133htn01 - exynos5800-peach-pi
* auo,b133xtn01 - tegra124-nyan-big
* boe,nv101wxmn51 - rk3399-gru-bob
* innolux,p120zdg-bf1 - sdm845-cheza
* lg,lp079qx1-sp0v - rk3399-evb and similar
* lg,lp097qx1-spa1 - According to commit 0355dde26e ("drm/panel:
simple: Add support for LG LP097QX1-SPA1 panel") this is an eDP
panel.
* lg,lp129qe - tegra124-venice2
* samsung,lsn122dl01-c01 - According to commit 0330eaf390
("drm/panel: simple: Add support for Samsung LSN122DL01-C01 panel")
this is an eDP panel.
* samsung,ltn140at29-301 - tegra124-nyan-blaze
* sharp,ld-d5116z01b - According to commit cd5e1cbe1f ("drm/panel:
simple: Add support for Sharp LD-D5116Z01B panel") this is an eDP
panel.
* sharp,lq123p1jx31 - rk3399-gru-kevin
* starry,kr122ea0sra - rk3399-gru-gru (reference board, not upstream)
I won't promise that I didn't miss a single panel, but that's fairly
complete I think.
I'm not sure the full impact of the fact that they didn't have the
connector type specified, but at least as of commit 9f069c6fbc
("drm/panel: panel-simple: add default connector_type") we may have
been accidentally thinking of them as DPI panels. We also would
certainly have had a warning. In any case since we don't want to
support anything eDP in the old simple-panel driver, we should move
these.
Cc: Yakir Yang <ykk@rock-chips.com>
Cc: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.8.I84e36f9f86d5d693fce0641a55ddb264a518a947@changeid
The panel-simple driver handles way too much. Let's start trying to
get a handle on it by splitting out the eDP panels. This patch does
this:
1. Start by copying simple-panel verbatim over to a new driver,
simple-panel-edp.
2. Rename "panel_simple" to "panel_edp" in the new driver.
3. Keep only panels marked with `DRM_MODE_CONNECTOR_eDP` in the new
driver. Remove those panels from the old driver.
4. Remove all recent "DP AUX bus" stuff from the old driver. The DP
AUX bus is only possible on DP panels.
5. Remove all DSI / MIPI related functions from the new driver.
6. Remove bus_format / bus_flags from eDP driver. These things don't
seem to make any sense for eDP panels so let's stop filling in made
up stuff.
In the end we end up with a bunch of duplicated code for now. Future
patches will try to address _some_ of this duplicated code though some
of it will be unavoidable.
NOTE: This may not actually move all eDP panels over to the new driver
since not all panels were properly marked with
`DRM_MODE_CONNECTOR_eDP`. A future patch will attempt to move wayward
panels I could identify but even so there may be some missed.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.7.I0a2f75bb822d17ce06f5b147734764eeb0c3e3df@changeid
In the patch ("drm/panel-simple-edp: Split eDP panels out of
panel-simple") we will split the PANEL_SIMPLE driver in two. By
default let's give everyone who had the old driver enabled the new
driver too. If folks want to opt-out of one or the other they always
can later.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.5.I02250cd7d4799661b068bcc65849a456ed411734@changeid
In the patch ("drm/edid: Allow the querying/working with the panel ID
from the EDID") we introduced a different way of working with the
panel ID stored in the EDID. Let's use this new way for the quirks
code.
Advantages of the new style:
* Smaller data structure size. Saves 4 bytes per panel.
* Iterate through quirks structure with just "==" instead of strncmp()
* In-kernel storage is more similar to what's stored in the EDID
itself making it easier to grok that they are referring to the same
value.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.4.I6103ce2b16e5e5a842b14c7022a034712b434609@changeid
EDIDs have 32-bits worth of data which is intended to be used to
uniquely identify the make/model of a panel. This has historically
been used only internally in the EDID processing code to identify
quirks with panels.
We'd like to use this panel ID in panel drivers to identify which
panel is hooked up and from that information figure out power sequence
timings. Let's expose this information from the EDID code and also
allow it to be accessed early, before a connector has been created.
To make matching in the panel drivers code easier, we'll return the
panel ID as a 32-bit value. We'll provide some functions for
converting this value back and forth to something more human readable.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.3.I4a672175ba1894294d91d3dbd51da11a8239cf4a@changeid
A future change wants to be able to read just block 0 of the EDID, so
break it out of drm_do_get_edid() into a sub-function.
This is intended to be a no-op change--just code movement.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.2.I62e76a034ac78c994d40a23cd4ec5aeee56fa77c@changeid
eDP panels generally contain almost everything needed to control them
in their EDID. This comes from their DP heritage were a computer needs
to be able to properly control pretty much any DP display that's
plugged into it.
The one big issue with eDP panels and the reason that we need a panel
driver for them is that the power sequencing can be different per
panel.
While it is true that eDP panel sequencing can be arbitrarily complex,
in practice it turns out that many eDP panels are compatible with just
some slightly different delays. See the contents of the bindings file
introduced in this patch for some details.
The fact that eDP panels are 99% probable and that the power
sequencing (especially power up) can be compatible between many panels
means that there's a constant desire to plug multiple different panels
into the same board. This could be for second sourcing purposes or to
support multiple SKUs (maybe a 11" and a 13", for instance).
As discussed [1], it should be OK to support this by adding two
properties to the device tree to specify the delays needed for
powering up the panel the first time. We'll create a new "edp-panel"
bindings file and define the two delays that might need to be
specified. NOTE: in the vast majority of the cases (HPD is hooked up
and isn't glitchy or is debounced) even these delays aren't needed.
[1] https://lore.kernel.org/r/CAD=FV=VZYOMPwQZzWdhJGh5cjJWw_EcM-wQVEivZ-bdGXjPrEQ@mail.gmail.com
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914132020.v5.1.I1116e79d34035338a45c1fc7cdd14a097909c8e0@changeid
Currently a failed allocation on sbi->upcase will cause an exit via
the label free_sbi causing a memory leak on object opts. Fix this by
re-ordering the exit paths free_opts and free_sbi so that kfree's occur
in the reverse allocation order.
Addresses-Coverity: ("Resource leak")
Fixes: 27fac77707 ("fs/ntfs3: Init spi more in init_fs_context than fill_super")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Current ntfs3 rst documentation is broken. I turn table to list table as
this is current Linux documentation quide line. Simple table also did
not quite work in our situation as we need to span rows together.
It still look quite good as text so we did not loss anything. This will
also make diffing quite bit more pleasure.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Right now sb blocksize first get initiliazed in fill_super but in can be
changed in helper function. It makes more sense to that this happened
only in one place.
Because we move this to helper function it makes more sense that
s_maxbytes will also be there. I rather have every sb releted thing in
fill_super, but because there is already sb releted stuff in this
helper. This will have to do for now.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Initializing should be as close as possible when we use it so that
we do not need to scroll up to see what is happening.
Also bdev_get_queue() can never return NULL so we do not need to check
for !rq.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
We can survive without this tmp point upcase. So remove it we don't have
so many tmp pointer in this function.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Drop tmp pointer bd_inode because this is only used ones in fill_super.
Also we have so many initializing happening at the beginning that it is
already way too much to follow.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
We only use this in two places so we do not really need it. Also
wrapper sb_rdonly() is pretty self explanatory. This will make little
bit easier to read this super long variable list in the beginning of
ntfs_fill_super().
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Use sb instead of sbi->sb in fill_super. We have sb so why not use
it. Also makes code more readable.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Remove some unnecessary variable loading. These look like copy paste
work and they are not used to anything.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
In many places it is not needed to use goto out. We can just return
right away. This will make code little bit more cleaner as we won't
need to check error path.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Remove root drop when we fault out. This can never happened because
when we allocate root we eather fault when no root or success.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Change EINVAL to ENOMEM when d_make_root fails because that is right
errno.
Signed-off-by: Kari Argillander <kari.argillander@gmail.com>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
128b/132b has a separate transcoder DDI mode, which also requires the
MST transport select to be set. Note that we'll use DP MST also for
single-stream 128b/132b.
Having the FDI and 128b/132b modes share the register mode value
complicates things a bit.
v2:
- Use HAS_DP20 abstraction for 128b/132b mode (Ville)
- Use intel_dp_is_uhbr() helper
Bspec: 50493
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/279bfbd979e0256fae13a5231e07e2f4fb665c07.1631191763.git.jani.nikula@intel.com