Shared FDB allows to direct traffic from all the vports in the HCA to a
single eswitch. In order to do that three things are needed.
1) Point the ingress ACL of the slave uplink to that of the master.
With this, wire traffic from both uplinks will reach the same eswitch
with the same metadata where a single steering rule can catch traffic
from both ports.
2) Set the FDB root flow table of the slave's eswitch to that of the
master. As this flow table can change dynamically make sure to
sync it on any set root flow table FDB command.
This will make sure traffic from SFs, VFs, ECPFs and PFs reach the
master eswitch.
3) Split wire traffic at the eswitch manager egress ACL so that it's
directed to the native eswitch manager. We only treat wire traffic
from both ports the same at the eswitch level. If such traffic wasn't
handled in the eswitch it needs to reach the right representor to be
processed by software. For example LACP packets should *always*
reach the right uplink representor for correct operation.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
If a netdev is removed from the lag the lag should be destroyed.
With downstream patches this might trigger a reconfiguration of
representors on a different eswitch and such we don't have the proper
locking to so from this path. Move the destruction to be done by the
workqueue.
As the destruction won't affect the netdev side it okay to do so.
The RDMA side will be reconfigured and it already coded to handle such
reconfiguration.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently when doing hardware lag we check the eswitch mode
but as this isn't done under a lock the check isn't valid.
As the code needs to sync between two different devices an extra
care is needed.
- When going to change eswitch mode, if hardware lag is active destroy it.
- While changing eswitch modes block any hardware bond creation.
- Delay handling bonding events until there are no mode changes in
progress.
- When attaching a new mdev to lag, block until there is no mode change
in progress. In order for the mode change to finish the interface lock
will have to be taken. Release the lock and sleep for 100ms to
allow forward progress. As this is a very rare condition (can happen if
the user unbinds and binds a PCI function while also changing eswitch
mode of the other PCI function) it has no real world impact.
As taking multiple eswitch mode locks is now required lockdep will
complain about a possible deadlock. Register a key per eswitch to make
lockdep happy.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When two mlx5 devices are paired in switchdev mode, always offload the
send-to-vport rule to the peer E-Switch. This allows to abstract
the logic when this is really necessary (single FDB) and combine
the logic of both cases into one.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
This callback will allow to notify representors about relevant events
when in OFFLOADS mode. In downstream patches, this will be used to notify
about PAIR/UNPAIR devcom events.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
FTEs are added with mapped metadata which is saved per eswitch.
When uplink reps are bonded and we are in a single FDB mode,
we could fail to find metadata which was stored on one eswitch mapping
but not the other or with a different id.
To resolve this issue use shared mapping between eswitch ports.
We do not have any conflict using a single mapping, for a type,
between the ports.
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Set the flow source param to local vport for the uplink rep
send-to-vport rule.
This will comply with the recent changes in SW steering that
use the flow source as an indication for the rule type - rx or tx.
Since the uplink send-to-vport rule is forwarding traffic to the wire
it has to indicate that it is an sx rule and can't use the any port
value in the flow source.
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Shared FDB allows to create a single RDMA device that holds representors
from both eswitches. As shared FDB is only active when both uplink
representors are enslaved there is a single RDMA port that represents
both uplinks.
The number of ports is the number of vports on both eswitches minus one
as we only need 1 port for both uplinks.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In shared FDB there is only one eswitch which is active and it receives
traffic from all representors and all vports in the HCA.
While the Ethernet representor will always reside on its native PF
the IB representor will not. Extend send to vport rule creation to
support such flows. Need to account for source vport that sends the
traffic (on which the representors resides) and the target eswitch
the traffic which reach.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In shared FDB a single RDMA device can have representors that are
connected to two different eswitches. Use the right eswitch when
preparing the response to userspace.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
As shared FDB requires changes in two subsystems first expose the needed
core functions so the RDMA side can be changed.
mlx5_lag_is_master(): return true if a given mlx5 device is the lag master.
mlx5_lag_is_shared_fdb(): Returns true if the lag mode is shared FDB.
mlx5_lag_get_peer_mdev(): Return the peer mdev in lag.
The mentioned functions will be used by downstream patches in order
to add support for shared FDB for the RDMA side.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Export a function so users can retrieve the mellanox device that manages
the eswitch from the eswitch device.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Mark Zhang <markzhang@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
On a 1->0->1 callbacks transition, there is an issue with the new
callback using the old callback's data.
Considering __DO_TRACE_CALL:
do { \
struct tracepoint_func *it_func_ptr; \
void *__data; \
it_func_ptr = \
rcu_dereference_raw((&__tracepoint_##name)->funcs); \
if (it_func_ptr) { \
__data = (it_func_ptr)->data; \
----> [ delayed here on one CPU (e.g. vcpu preempted by the host) ]
static_call(tp_func_##name)(__data, args); \
} \
} while (0)
It has loaded the tp->funcs of the old callback, so it will try to use the old
data. This can be fixed by adding a RCU sync anywhere in the 1->0->1
transition chain.
On a N->2->1 transition, we need an rcu-sync because you may have a
sequence of 3->2->1 (or 1->2->1) where the element 0 data is unchanged
between 2->1, but was changed from 3->2 (or from 1->2), which may be
observed by the static call. This can be fixed by adding an
unconditional RCU sync in transition 2->1.
Note, this fixes a correctness issue at the cost of adding a tremendous
performance regression to the disabling of tracepoints.
Before this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m0.778s
user 0m0.000s
sys 0m0.061s
After this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m10.593s
user 0m0.017s
sys 0m0.259s
A follow up fix will introduce a more lightweight scheme based on RCU
get_state and cond_sync, that will return the performance back to what it
was. As both this change and the lightweight versions are complex on their
own, for bisecting any issues that this may cause, they are kept as two
separate changes.
Link: https://lkml.kernel.org/r/20210805132717.23813-3-mathieu.desnoyers@efficios.com
Link: https://lore.kernel.org/io-uring/4ebea8f0-58c9-e571-fd30-0ce4f6f09c70@samba.org/
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Stefan Metzmacher <metze@samba.org>
Fixes: d25e37d89d ("tracepoint: Optimize using static_call()")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
On transition from 2->1 callees, we should be comparing .data rather
than .func, because the same callback can be registered twice with
different data, and what we care about here is that the data of array
element 0 is unchanged to skip rcu sync.
Link: https://lkml.kernel.org/r/20210805132717.23813-2-mathieu.desnoyers@efficios.com
Link: https://lore.kernel.org/io-uring/4ebea8f0-58c9-e571-fd30-0ce4f6f09c70@samba.org/
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Stefan Metzmacher <metze@samba.org>
Fixes: 547305a646 ("tracepoint: Fix out of sync data passing by static caller")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Add ACPI module ID to probe the driver from the ACPI based bootloader
firmware.
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Current release - regressions:
- sched: taprio: fix init procedure to avoid inf loop when dumping
- sctp: move the active_key update after sh_keys is added
Current release - new code bugs:
- sparx5: fix build with old GCC & bitmask on 32-bit targets
Previous releases - regressions:
- xfrm: redo the PREEMPT_RT RCU vs hash_resize_mutex deadlock fix
- xfrm: fixes for the compat netlink attribute translator
- phy: micrel: Fix detection of ksz87xx switch
Previous releases - always broken:
- gro: set inner transport header offset in tcp/udp GRO hook to avoid
crashes when such packets reach GSO
- vsock: handle VIRTIO_VSOCK_OP_CREDIT_REQUEST, as required by spec
- dsa: sja1105: fix static FDB entries on SJA1105P/Q/R/S and SJA1110
- bridge: validate the NUD_PERMANENT bit when adding an extern_learn FDB entry
- usb: lan78xx: don't modify phy_device state concurrently
- usb: pegasus: check for errors of IO routines
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/rrJ
-----END PGP SIGNATURE-----
Merge tag 'net-5.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from ipsec.
Current release - regressions:
- sched: taprio: fix init procedure to avoid inf loop when dumping
- sctp: move the active_key update after sh_keys is added
Current release - new code bugs:
- sparx5: fix build with old GCC & bitmask on 32-bit targets
Previous releases - regressions:
- xfrm: redo the PREEMPT_RT RCU vs hash_resize_mutex deadlock fix
- xfrm: fixes for the compat netlink attribute translator
- phy: micrel: Fix detection of ksz87xx switch
Previous releases - always broken:
- gro: set inner transport header offset in tcp/udp GRO hook to avoid
crashes when such packets reach GSO
- vsock: handle VIRTIO_VSOCK_OP_CREDIT_REQUEST, as required by spec
- dsa: sja1105: fix static FDB entries on SJA1105P/Q/R/S and SJA1110
- bridge: validate the NUD_PERMANENT bit when adding an extern_learn
FDB entry
- usb: lan78xx: don't modify phy_device state concurrently
- usb: pegasus: check for errors of IO routines"
* tag 'net-5.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (48 commits)
net: vxge: fix use-after-free in vxge_device_unregister
net: fec: fix use-after-free in fec_drv_remove
net: pegasus: fix uninit-value in get_interrupt_interval
net: ethernet: ti: am65-cpsw: fix crash in am65_cpsw_port_offload_fwd_mark_update()
bnx2x: fix an error code in bnx2x_nic_load()
net: wwan: iosm: fix recursive lock acquire in unregister
net: wwan: iosm: correct data protocol mask bit
net: wwan: iosm: endianness type correction
net: wwan: iosm: fix lkp buildbot warning
net: usb: lan78xx: don't modify phy_device state concurrently
docs: networking: netdevsim rules
net: usb: pegasus: Remove the changelog and DRIVER_VERSION.
net: usb: pegasus: Check the return value of get_geristers() and friends;
net/prestera: Fix devlink groups leakage in error flow
net: sched: fix lockdep_set_class() typo error for sch->seqlock
net: dsa: qca: ar9331: reorder MDIO write sequence
VSOCK: handle VIRTIO_VSOCK_OP_CREDIT_REQUEST
mptcp: drop unused rcu member in mptcp_pm_addr_entry
net: ipv6: fix returned variable type in ip6_skb_dst_mtu
nfp: update ethtool reporting of pauseframe control
...
gpiolib does not modify struct device_node, so few local pointers can
point to a const data.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Several gpiolib functions receive pointer to struct device_node which is
later passed to OF functions. These OF functions accept already pointer
to const, so gpiolib can follow similar approach to indicate they are
not modifying the struct device_node.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Unify the declaration of of_count_phandle_with_args() between enabled
and disabled OF by making constifying pointed device_node.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Interrupt is optional for the RT5640 codec. Nexus 7 doesn't use interrupt,
this results in a noisy warning message that looks like a error condition.
Make interrupt explicitly optional to silence the message, use modern
IRQF_NO_AUTOEN flag and correct the reg[q]uest typo in the message.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210802185258.1881-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
WCD938x has Multi Button Headset Control hardware to support Headset
insertion, type detection, 8 headset buttons detection, Over Current
detection and Impedence measurements.
This patch adds support for this using wcd-mbhc apis.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210716105918.7301-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
buswidth and dtr fields in spi_mem_op are only valid when the
corresponding spi_mem_op phase has a non-zero length. For example,
SPI NAND core doesn't set buswidth when using SPI_MEM_OP_NO_ADDR
phase.
Fix the dtr checks in set_protocol() and suppports_mem_op() to
ignore empty spi_mem_op phases, as checking for dtr field in
empty phase will result in false negatives.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Link: https://lore.kernel.org/r/20210716232504.182-3-a-nandan@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S always has two LRCLK phases and both CH1 and CH2 of the RX
must be enabled (corresponding to the low and high phases of LRCLK.)
The selection of the valid data channels is done by setting the DAC
CHA_SEL and CHB_SEL. CHA_SEL is always the first (left) channel,
CHB_SEL depends on the number of active channels.
Previously for mono ASP CH2 was not enabled, the result was playing
mono data would not produce any audio output.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 621d65f3b8 ("ASoC: cs42l42: Provide finer control on playback path")
Link: https://lore.kernel.org/r/20210805161111.10410-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The lowest valid SCLK corresponds to 44.1 kHz at 16-bit. Sample
rates less than this would produce SCLK below the minimum when using
a normal I2S frame. A constraint must be applied to prevent this.
The constraint is not applied if the machine driver sets SCLK, to
allow setups where the host generates additional bits per LRCLK
phase to increase the SCLK frequency. In these cases the machine
driver would always have to inform this driver of the actual SCLK,
and it must select a legal SCLK.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210805161111.10410-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An I2S frame starts on the falling edge of LRCLK so ASP_STP must
be 0.
At the same time, move other format settings in the same register
from cs42l42_pll_config() to cs42l42_set_dai_fmt() where you'd
expect to find them, and merge into a single write.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210805161111.10410-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both SCLK and PLL clocks must be running to drive the glitch-free mux
behind MCLK_SRC_SEL and complete the switchover.
This patch moves the writing of MCLK_SRC_SEL to when the PLL is started
and stopped, so that it only transitions while the PLL is running.
The unconditional write MCLK_SRC_SEL=0 in cs42l42_mute_stream() is safe
because if the PLL is not running MCLK_SRC_SEL is already 0.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 43fc357199 ("ASoC: cs42l42: Set clock source for both ways of stream")
Link: https://lore.kernel.org/r/20210805161111.10410-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an else-if condition in the probe function to check whether ngpios is
multiple of 8.
Per AST datasheet, numbers of available serial GPIO pins in Serial GPIO
Configuration Register must be n bytes. For instance, if n = 1, it means
AST SoC supports 8 GPIO pins.
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Replace all of_property_read_u32() with device_property_read_u32().
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The current design initializes irq->chip from a global irqchip struct,
which causes multiple sgpio devices use the same irq_chip.
The patch moves irq_chip to aspeed_sgpio struct for initializing
irq_chip from their private gpio struct.
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
AST SoC supports *retain pin state* function when wdt reset.
The patch adds set_config function for handling sgpio reset tolerance
register.
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The maximum number of gpio pins of SoC is hardcoded as 80 and the gpio pin
count mask for GPIO Configuration register is hardcode as GENMASK(9,6).
However, AST2600 has 2 sgpio master interfaces, one of them supports up
to 128 gpio pins and pin count mask of GPIO Configuration Register is 5
bits.
The patch adds ast2600 compatibles, removes MAX_NR_HW_SGPIO and
corresponding design to make the gpio input/output pin base are determined
by ngpios.
The patch also removed hardcoded pin mask and adds ast2400, ast2500,
ast2600 platform data that include gpio pin count mask for GPIO
Configuration Register.
The original pin order is as follows:
(suppose MAX_NR_HW_SGPIO is 80 and ngpios is 10 as well)
Input:
0 1 2 3 ... 9
Output:
80 81 82 ... 89
The new pin order is as follows:
Input:
0 2 4 6 ... 18
Output:
1 3 5 7 ... 19
SGPIO pin id and input/output pin mapping is as follows:
SGPIO0(0,1), SGPIO1(2,3), ..., SGPIO79(158,159)
For example:
Access SGPIO5(10,11)
Get SGPIO pin 5 (suppose sgpio chip id is 2)
gpioget 2 10
Set SGPIO pin 5 (suppose sgpio chip id is 2)
gpioset 2 11=1
gpioset 2 11=0
Signed-off-by: Steven Lee <steven_lee@aspeedtech.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Two minor corrections for return values, and one more important one
for max98090 where duplicate reads don't seem necessary.
Pierre-Louis Bossart (3):
ASoC: max98090: remove duplicate status reads and useless assignmment
ASoC: mt6359-accdet.c: remove useless assignments
ASoC: wcd938x: simplify return value
sound/soc/codecs/max98090.c | 4 +---
sound/soc/codecs/mt6359-accdet.c | 8 ++++----
sound/soc/codecs/wcd938x.c | 2 +-
3 files changed, 6 insertions(+), 8 deletions(-)
--
2.25.1
Hi Mark
Now I'm posting audio-graph-card2 patch-set, but it seems it needs longer
discussion. Thus I want to post more easy patch first, and reduce my
local patches.
These are cppcheck warning cleanup patches for soc-dapm.
Kuninori Morimoto (12):
ASoC: soc-dapm: cleanup cppcheck warning at dapm_wcache_lookup()
ASoC: soc-dapm: cleanup cppcheck warning at dapm_connect_mux()
ASoC: soc-dapm: cleanup cppcheck warning at dapm_set_mixer_path_status()
ASoC: soc-dapm: cleanup cppcheck warning at dapm_new_pga()
ASoC: soc-dapm: cleanup cppcheck warning at dapm_new_dai_link()
ASoC: soc-dapm: cleanup cppcheck warning at dapm_seq_check_event()
ASoC: soc-dapm: cleanup cppcheck warning at dapm_seq_run()
ASoC: soc-dapm: cleanup cppcheck warning at snd_soc_dapm_del_route()
ASoC: soc-dapm: cleanup cppcheck warning at snd_soc_dapm_add_routes()
ASoC: soc-dapm: cleanup cppcheck warning at snd_soc_dapm_weak_routes()
ASoC: soc-dapm: cleanup cppcheck warning at snd_soc_dapm_new_controls()
ASoC: soc-dapm: cleanup cppcheck warning at soc_dapm_dai_stream_event()
sound/soc/soc-dapm.c | 65 ++++++++++++++++++++++----------------------
1 file changed, 33 insertions(+), 32 deletions(-)
--
2.25.1
syzbot is hitting might_sleep() warning at hci_sock_dev_event() due to
calling lock_sock() with rw spinlock held [1].
It seems that history of this locking problem is a trial and error.
Commit b40df5743e ("[PATCH] bluetooth: fix socket locking in
hci_sock_dev_event()") in 2.6.21-rc4 changed bh_lock_sock() to
lock_sock() as an attempt to fix lockdep warning.
Then, commit 4ce61d1c7a ("[BLUETOOTH]: Fix locking in
hci_sock_dev_event().") in 2.6.22-rc2 changed lock_sock() to
local_bh_disable() + bh_lock_sock_nested() as an attempt to fix the
sleep in atomic context warning.
Then, commit 4b5dd696f8 ("Bluetooth: Remove local_bh_disable() from
hci_sock.c") in 3.3-rc1 removed local_bh_disable().
Then, commit e305509e67 ("Bluetooth: use correct lock to prevent UAF
of hdev object") in 5.13-rc5 again changed bh_lock_sock_nested() to
lock_sock() as an attempt to fix CVE-2021-3573.
This difficulty comes from current implementation that
hci_sock_dev_event(HCI_DEV_UNREG) is responsible for dropping all
references from sockets because hci_unregister_dev() immediately
reclaims resources as soon as returning from
hci_sock_dev_event(HCI_DEV_UNREG).
But the history suggests that hci_sock_dev_event(HCI_DEV_UNREG) was not
doing what it should do.
Therefore, instead of trying to detach sockets from device, let's accept
not detaching sockets from device at hci_sock_dev_event(HCI_DEV_UNREG),
by moving actual cleanup of resources from hci_unregister_dev() to
hci_cleanup_dev() which is called by bt_host_release() when all
references to this unregistered device (which is a kobject) are gone.
Since hci_sock_dev_event(HCI_DEV_UNREG) no longer resets
hci_pi(sk)->hdev, we need to check whether this device was unregistered
and return an error based on HCI_UNREGISTER flag. There might be subtle
behavioral difference in "monitor the hdev" functionality; please report
if you found something went wrong due to this patch.
Link: https://syzkaller.appspot.com/bug?extid=a5df189917e79d5e59c9 [1]
Reported-by: syzbot <syzbot+a5df189917e79d5e59c9@syzkaller.appspotmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: e305509e67 ("Bluetooth: use correct lock to prevent UAF of hdev object")
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clang warns:
drivers/staging/r8188eu/core/rtw_mlme.c:1629:28: warning: address of
array 'pmlmepriv->assoc_ssid.Ssid' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (pmlmepriv->assoc_ssid.Ssid && pmlmepriv->assoc_ssid.SsidLength) {
~~~~~~~~~~~~~~~~~~~~~~^~~~ ~~
1 warning generated.
Ssid is an array not at the beginning of a struct so its address cannot
be NULL so remove the check.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210805185807.3296077-4-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns:
drivers/staging/r8188eu/hal/rtl8188e_rf6052.c:344:13: warning:
explicitly assigning value of variable of type 'u32' (aka 'unsigned
int') to itself [-Wself-assign]
writeVal = writeVal;
~~~~~~~~ ^ ~~~~~~~~
1 warning generated.
Remove this branch as it is useless.
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210805185807.3296077-3-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns several times across the driver along the lines of:
drivers/staging/r8188eu/core/rtw_pwrctrl.c:222:21: warning: equality
comparison with extraneous parentheses [-Wparentheses-equality]
if ((pwrpriv->rpwm == pslv)) {
~~~~~~~~~~~~~~^~~~~~~
drivers/staging/r8188eu/core/rtw_pwrctrl.c:222:21: note: remove
extraneous parentheses around the comparison to silence this warning
if ((pwrpriv->rpwm == pslv)) {
~ ^ ~
drivers/staging/r8188eu/core/rtw_pwrctrl.c:222:21: note: use '=' to turn
this equality comparison into an assignment
if ((pwrpriv->rpwm == pslv)) {
^~
=
1 warning generated.
The compilers have agreed that single parentheses are used for equality
and double parentheses are used for assignment within control flow
statements such as if and while so remove them in these places to fix
the warning.
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20210805185807.3296077-2-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=ewLR
-----END PGP SIGNATURE-----
Merge tag 'selinux-pr-20210805' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux fix from Paul Moore:
"One small SELinux fix for a problem where an error code was not being
propagated back up to userspace when a bogus SELinux policy is loaded
into the kernel"
* tag 'selinux-pr-20210805' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: correct the return value when loads initial sids
Pull ucounts fix from Eric Biederman:
"Fix a subtle locking versus reference counting bug in the ucount
changes, found by syzbot"
* 'for-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ucounts: Fix race condition between alloc_ucounts and put_ucounts
- Fix NULL pointer dereference caused by an error path
- Give histogram calculation fields a size, otherwise it breaks synthetic
creation based on them.
- Reject strings being used for number calculations.
- Fix recordmcount.pl warning on llvm building RISC-V allmodconfig
- Fix the draw_functrace.py script to handle the new trace output
- Fix warning of smp_processor_id() in preemptible code
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYQwR+xQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qtHOAQD7gBn1cRK0T3Eolf5HRd14PLDVUZ1B
iMZuTJZzJUWLSAD/ec3ezcOafNlPKmG1ta8UxrWP5VzHOC5qTIAJYc1d5AA=
=7FNB
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Various tracing fixes:
- Fix NULL pointer dereference caused by an error path
- Give histogram calculation fields a size, otherwise it breaks
synthetic creation based on them.
- Reject strings being used for number calculations.
- Fix recordmcount.pl warning on llvm building RISC-V allmodconfig
- Fix the draw_functrace.py script to handle the new trace output
- Fix warning of smp_processor_id() in preemptible code"
* tag 'trace-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Quiet smp_processor_id() use in preemptable warning in hwlat
scripts/tracing: fix the bug that can't parse raw_trace_func
scripts/recordmcount.pl: Remove check_objcopy() and $can_use_local
tracing: Reject string operand in the histogram expression
tracing / histogram: Give calculation hist_fields a size
tracing: Fix NULL pointer dereference in start_creating