TLB synchronisation typically involves the SMMU blocking all incoming
transactions until the TLBs report completion of all outstanding
operations. In the common SMMUv2 configuration of a single distributed
SMMU serving multiple peripherals, that means that a single unmap
request has the potential to bring the hammer down on the entire system
if synchronised globally. Since stage 1 contexts, and stage 2 contexts
under SMMUv2, offer local sync operations, let's make use of those
wherever we can in the hope of minimising global disruption.
To that end, rather than add any more branches to the already unwieldy
monolithic TLB maintenance ops, break them up into smaller, neater,
functions which we can then mix and match as appropriate.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM_AMMU_CB() is calculated relative to ARM_SMMU_CB_BASE(), but the
latter is never of use on its own, and what we end up with is the same
ARM_SMMU_CB_BASE() + ARM_AMMU_CB() expression being duplicated at every
callsite. Folding the two together gives us a self-contained context
bank accessor which is much more pleasant to work with.
Secondly, we might as well simplify CB_BASE itself at the same time.
We use the address space size for its own sake precisely once, at probe
time, and every other usage is to dynamically calculate CB_BASE over
and over and over again. Let's flip things around so that we just
maintain the CB_BASE address directly.
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Calculating ASIDs/VMIDs dynamically from arm_smmu_cfg was a neat trick,
but the global uniqueness workaround makes it somewhat more awkward, and
means we end up having to pass extra state around in certain cases just
to keep a handle on the offset.
We already have 16 bits going spare in arm_smmu_cfg; let's just
precalculate an ASID/VMID, plop it in there, and tidy up the users
accordingly. We'd also need something like this anyway if we ever get
near to thinking about SVM, so it's no bad thing.
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
16-bit ASID should be enabled before initializing TTBR0/1,
otherwise only LSB 8-bit ASID will be considered. Hence
moving configuration of TTBCR register ahead of TTBR0/1
while initializing context bank.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
[will: rewrote comment]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Firmware is responsible for properly enabling smmu workarounds. Print
a message for better diagnostics when Cavium erratum 27704 was
detected.
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This is a fairly subtle thing - let's make sure it's described as
clearly as possible to avoid potential misunderstandings.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Implement the ->apply() hook and drop the ->enable(), ->disable,
->set_polarity and ->config() ones.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When we use virtio-vga with a big-endian guest,
the mouse pointer disappears.
To fix that, on big-endian use DRM_FORMAT_BGRA8888
instead of DRM_FORMAT_ARGB8888.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170405080915.823-1-lvivier@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
If the PWM was not enabled at U-Boot loader, PWM could not work for
clock always disabled at PWM driver. The PWM clock is enabled at
beginning of pwm_apply(), but disabled at end of pwm_apply().
If the PWM was enabled at U-Boot loader, PWM clock is always enabled
unless closed by ATF. The pwm-backlight might turn off the power at
early suspend, should disable PWM clock for saving power consume.
It is important to provide opportunity to enable/disable clock at PWM
driver, the PWM consumer should ensure correct order to call PWM enable
and disable, and PWM driver ensure state of PWM clock synchronized with
PWM enabled state.
Fixes: 2bf1c98aa5 ("pwm: rockchip: Add support for atomic update")
Cc: stable@vger.kernel.org
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
These two functions awkwardly break up the otherwise-contiguous chunk of
related Intuos IRQ functions with a 500 line tangent about the operation
of the EKR. Their presence makes it difficult to read/navigate through the
the Intuos code. Since there is no dependency between these functions, it
is possible to simply move them down somewhat. This commit moves them
to be after the final Intuos IRQ function.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commits d793ff8 and 4082da8 introduced two pad usages which do not
actually send pad input events. To make sure we do not post empty
pad packets, pad_input_event_flag is introduced. Turn on the flag
for real pad input events so we can synchronize them properly.
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device has a different vendor id but responds to initialization.
Signed-off-by: Xiaolei Yu <dreifachstein@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
At least on cherrytrail, the update bit will never go low when the
enabled bit is not set.
This causes the backlight on my cube iwork8 air tablet to never turn on
again after being turned off because in the pwm_lpss_apply enable path
pwm_lpss_update will fail causing an error exit and the enable-bit to
never get set. Any following pwm_lpss_apply calls will fail the
pwm_lpss_is_updating check.
Since the docs say that the update bit should be set before the
enable-bit, split pwm_lpss_update into setting the update-bit and
pwm_lpss_wait_for_update, and move the pwm_lpss_wait_for_update call
in the enable path to after setting the enable-bit.
Fixes: 10d56a4 ("pwm: lpss: Avoid reconfiguring while UPDATE bit...")
Cc: Ilkka Koskinen <ilkka.koskinen@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
As a preparation for special treatment for Broxton we split Tangier
configuration.
Fixes: b89b4b7a3d ("pwm: lpss: pci: Enable PWM module on Intel Edison")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
err is being checked for failure each time it is being updated
so this err check is totally redundant and can be removed
Detected with CoverityScan, CID#1420665 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add basic support for the MIPS Virtualization Module (generally known as
MIPS VZ) in KVM. We primarily support the ImgTec P5600, P6600, I6400,
and Cavium Octeon III cores so far. Support is included for the
following VZ / guest hardware features:
- MIPS32 and MIPS64, r5 (VZ requires r5 or later) and r6
- TLBs with GuestID (IMG cores) or Root ASID Dealias (Octeon III)
- Shared physical root/guest TLB (IMG cores)
- FPU / MSA
- Cop0 timer (up to 1GHz for now due to soft timer limit)
- Segmentation control (EVA)
- Hardware page table walker (HTW) both for root and guest TLB
Also included is a proper implementation of the TLBR instruction for the
trap & emulate MIPS KVM implementation.
Preliminary MIPS architecture changes are applied directly with Ralf's
ack.
-----BEGIN PGP SIGNATURE-----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=smiL
-----END PGP SIGNATURE-----
Merge tag 'kvm_mips_4.12_1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/kvm-mips
From: James Hogan <james.hogan@imgtec.com>
KVM: MIPS: VZ support, Octeon III, and TLBR
Add basic support for the MIPS Virtualization Module (generally known as
MIPS VZ) in KVM. We primarily support the ImgTec P5600, P6600, I6400,
and Cavium Octeon III cores so far. Support is included for the
following VZ / guest hardware features:
- MIPS32 and MIPS64, r5 (VZ requires r5 or later) and r6
- TLBs with GuestID (IMG cores) or Root ASID Dealias (Octeon III)
- Shared physical root/guest TLB (IMG cores)
- FPU / MSA
- Cop0 timer (up to 1GHz for now due to soft timer limit)
- Segmentation control (EVA)
- Hardware page table walker (HTW) both for root and guest TLB
Also included is a proper implementation of the TLBR instruction for the
trap & emulate MIPS KVM implementation.
Preliminary MIPS architecture changes are applied directly with Ralf's
ack.
Make sure we sure register any sensor when sony_input_configured failes.
Somehow this line got lost during resolving of merge conflicts in the
motion sensor patch series and a redudant remove was added as well later
on.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
By default when using bluetooth the DS4 reports data at about 1kHz,
which is quite fast especially on weak devices. We now make the
device use the USB poll interval, which is a fixed 4ms. In addition
we make the value adjustable through sysfs.
The error handling in sony_input_configured is a little tricky. It
is not easy to add other goto's as not all codepaths have logic
for adding this attribute. Luckily we are setting the value for the
attribute to a default value, so we can use that to detect if we need
to remove the file.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Only set bit flags for the portions of the DS4 output report
for which we have data.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These colors are more the default colors normally used on the DS4.
The previous ones were faint and not so noticeable.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The navigation controller is a DS3 (sixaxis) with fewer physical
axes and buttons. It utilizes the same HID report as the DS3 and
thus reports axes/buttons which aren't physically present.
Currently many non-existing buttons and axes are reported, which
we are now removing.
For the axes/buttons which do exist, we make the axis/button mapping
similar to the DS3.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The DS3 MAC address is reported as a unique identified when
using Bluetooth. For USB there is no unique identifier reported
yet, so use the MAC address.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This way, upower can add a simple udev rule to decide whether or not
it should use the internal unifying support or just the generic kernel
one.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Solar Keyboard uses a different feature to report the battery level.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CAPACITY LEVEL allows to forward rough information on the battery mileage.
HID++ 2.0 devices will either report percentage or levels, so better
forwarding this information to the user space.
The M325 supports only 2 levels: 'Full' and 'Critical'. With mileage,
it will report either 90% or 5%, which might confuse users. With this
change the battery will either report "Full" or "Critical".
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The power_supply term for the percentage is capacity. Capacity level
can be given when non accurate mileage is provided by the device, so
better stick to the terms used in power_supply.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When ONLINE isn't set, upower should ignore the battery capacity,
so there is no need to overload it with some random values.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a device reconnects, there is a high chance its power supply has
been changed (for a battery replacement for instance). Just forward
the battery state here.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Or the device just answers a valid feature '0'.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The creation of the power_supply should not be in a HID++ 2.0 specific
function.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Better forwarding the device name, manufacturer and serial to upower.
Note that serial is still empty, it will be filled in a later patch
in this series.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Battery events are reported through HID++, so we need to be sure
the report ID is the HID++ one.
Without this, we might receive keyboard events that looks just like
battery events with wrong data and which will confuse user space.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Looks like all users don't care about a disconnect.
Simplify the various variant_connect() and put the connect state check
at the beginning.
For delayed input devices, make sure we go through all other connect
values (protocol, battery) before bailing out.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hidpp->name can't be null.
Only HID++ 2.0 and above device supports the query.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Unifying devices are different from others because they can probed
while not connected. So we need to talk to the receiver to get some
extra information like the device name and the serial.
Instead of having conditionals while attempting to read the device name
from HID++ 2.0, have a special init path for them.
Store the retrieved serial in hdev->uniq.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Do not pollute the quirks bits field which is public API
with elements that are queried from the device.
Move the 2 battery capabilities into the new field.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Unless they are connected through unifying, they don't support it,
so remove one error in the logs.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Without a scope defined, UPower assumes that the battery provides
power to the computer it's connected to, like a laptop battery or a UPS.
Tested-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Register 0xB5 should be handled specially no matter what function is
used. This allows to retrieve the serial and the Quad ID from
hid-logitech-hidpp directly.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many sightings report the greater prevalence of allocation failures.
This is all due to the incorrect use of mapping_gfp_constraint(), so
remove it in favour of just querying the mapping_gfp_mask() which are
the exact gfp_t we wanted in the first place.
We still do expect a higher chance of reporting ENOMEM, as that is the
intention of using __GFP_NORETRY -- to fail rather than oom after having
reclaimed from our bo caches, and having done a direct|kswapd reclaim
pass.
Reported-by: Jason Ekstrand <jason.ekstrand@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100594
Fixes: 24f8e00a8a ("drm/i915: Prefer to report ENOMEM rather than incur the oom for gfx allocations")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170405221514.23251-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
As per BSPEC, valid cdclk values for glk are 79.2, 158.4, 316.8 Mhz.
Practically we can achive only 99% of these cdclk values (HW team
checking on this). So cdclk should be calculated for the given pixclk as
per that otherwise it may lead to screen corruption, explained below:
1. For DSI AUO panel(1920x1200 @60) required pixclk is 157100 KHZ
2. glk_calc_cdclk returns 79200 KHZ for this pixclk, For 2PPC it
will be 158400 KHZ
3. Practically 100% of the cdclk can’t be achieved, so 99% of 158400
KHZ = 156816 which is less than the desired pixlclk and causes
panel corruption.
v2: Rebased to new CDLCK code framework
v3: Addressed review comments from Ander/Jani
- Add comment in code about 99% usage of CDCLK
- Calculate max dot clock as well with 99% limit
v4 by Jani:
- drop superfluous whitespace change
- rewrite code comments to clarify
v5: Added details of non-working scenario in commit message
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491397463-13637-1-git-send-email-madhav.chauhan@intel.com
There is some conflation related to sink rates, making this change more
complicated than it would otherwise have to be. There are three changes
here that are rather difficult to split up:
1) Use the intel_dp->sink_rates array for all DP, not just eDP 1.4. We
initialize it from DPCD on eDP 1.4 like before, but generate it based
on DP_MAX_LINK_RATE on others. This reduces code complexity when we
need to use the sink rates; they are all always in the sink_rates
array.
2) Update the sink rate array whenever we read DPCD, and use the
information from there. This increases code readability when we need
the sink rates.
3) Disentangle fallback rate limiting from sink rates. In the code, the
max rate is a dynamic property of the *link*, not of the *sink*. Do
the limiting after intersecting the source and sink rates, which are
static properties of the devices.
This paves the way for follow-up refactoring that I've refrained from
doing here to keep this change as simple as it possibly can.
v2: introduce use_rate_select and handle non-confirming eDP (Ville)
v3: don't clobber cached eDP rates on short pulse (Ville)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/071bad76467f8ab2e73f3f61ad52d5a468004c71.1490712890.git.jani.nikula@intel.com
We need the source rates array so often that it makes sense to set it
once at init. This reduces function calls when we need the rates, making
the code easier to follow.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/aa998882d2b824f671272c60e9d26621ab9d2d17.1490712890.git.jani.nikula@intel.com
Rename the function, move it at the top, and reuse in
intel_dp_link_rate_index(). If there was a reason in the past to use
reverse search order here, there isn't now.
The names may be slightly confusing now, but intel_dp_link_rate_index()
will go away in follow-up patches.
v2: Use name intel_dp_rate_index (Dhinakaran)
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/c7b6197aaa12e368a0d024dc142fa574fd0443a7.1490712890.git.jani.nikula@intel.com
We shouldn't silently use the first element if we can't find the rate
we're looking for. Make rate_to_index() more generally useful, and
fallback to the first element in the caller, with a big warning.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/8a6e83b7bf35da0cbbc703ae157944107ff145be.1490712890.git.jani.nikula@intel.com
I can't think of a real world bug this could cause now, but this will be
required in follow-up work. While at it, change the parameter order to
be slightly more sensible.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/ff5b08f45a72c2247f5326b080027e2f5d8cc4ee.1490712890.git.jani.nikula@intel.com
Inject adapter interrupts on a specified adapter which allows to
retrieve the adapter flags, e.g. if the adapter is subject to AIS
facility or not. And add documentation for this interface.
For adapters subject to AIS, handle the airq injection suppression
for a given ISC according to the interruption mode:
- before injection, if NO-Interruptions Mode, just return 0 and
suppress, otherwise, allow the injection.
- after injection, if SINGLE-Interruption Mode, change it to
NO-Interruptions Mode to suppress the following interrupts.
Besides, add tracepoint for suppressed airq and AIS mode transitions.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Fei Li <sherrylf@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>