Add a void *data pointer to struct generic_pm_domain_data. Because this
exists for each device associated with a genpd it will allow us to
assign per-device data if needed on a platform for control of that
specific device.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Chen-Yu and I have a shared git tree to host the sunxi patches now, so
let's document it.
And while we're at it, enhance our regex and document a few directories
that have been asked for in the past.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
During probe, the rcar_can driver prints:
rcar_can e6e80000.can: device registered (regs @ e08bc000, IRQ76)
The "regs" value is a virtual address, exposing internal information,
hence stop printing it. The (useful) physical address is already
printed as part of the device name.
Fixes: fd1159318e ("can: add Renesas R-Car CAN driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Starting from commit 5de85b9d57 ("PM / runtime: Re-init runtime PM
states at probe error and driver unbind") pm_runtime core now changes
device runtime_status back to after RPM_SUSPENDED after a probe defer.
Certain OMAP devices make use of "ti,no-idle-on-init" flag which causes
omap_device_enable to be called during the BUS_NOTIFY_ADD_DEVICE event
during probe, along with pm_runtime_set_active.
This call to pm_runtime_set_active typically will prevent a call to
pm_runtime_get in a driver probe function from re-enabling the
omap_device. However, in the case of a probe defer that happens before
the driver probe function is able to run, such as a missing pinctrl
states defer, pm_runtime_reinit will set the device as RPM_SUSPENDED and
then once driver probe is actually able to run, pm_runtime_get will see
the device as suspended and call through to the omap_device layer,
attempting to enable the already enabled omap_device and causing errors
like this:
omap-gpmc 50000000.gpmc: omap_device: omap_device_enable() called from
invalid state 1
omap-gpmc 50000000.gpmc: use pm_runtime_put_sync_suspend() in driver?
We can avoid this error by making sure the pm_runtime status of a device
matches the omap_device state before a probe attempt. By extending the
omap_device bus notifier to act on the BUS_NOTIFY_BIND_DRIVER event we
can check if a device is enabled in omap_device but with a pm_runtime
status of RPM_SUSPENDED and once again mark the device as RPM_ACTIVE to
avoid a second incorrect call to omap_device_enable.
Fixes: 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This binding describes the Amlogic Meson specific extension to the
Synopsys Designware HDMI Controller.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic Meson GXBB/GXL/GXM SoCs embeds a Synopsys DesignWare HDMI TX
Controller with a custom Bridge + PHY around the Controller.
This driver makes uses of all the custom PHY plat data callbacks and enables
the compatible HDMI modes to be configured as a drm_encoder instance.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch adds support for the supported HDMI Venc modes and add the VPP mux
value to switch to ENCP encoder.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patchs adds support for the supported HDMI modes clocks frequencies.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Since this is managed now by the components code, if CVBS is not available
and HDMI neither, the drm driver won't bind anyway.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch adds support for optional components connected through the
Device Tree endpoints scheme.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Clean the crtc_enable by using the proper crtc_state instead of the state
of the primary plane state data.
Also fix the dependency to commit the plane changes even if enable is called
after the flush.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This avoids duplicating the logic four times, and it also allows to keep
some helpers static in core.c or just opencode them.
Note that this loses printing the aborted status on completions in the
PCI driver as that uses a data structure not available any more.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
A requeue means we go through nvme_fc_start_fcp_op again and get
another controller reference. To make sure the refcount doesn't
leak we also need to drop it for every completion that came from
the LLDD.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This way our max retry limit holds as well.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This way our max retry limit holds as well.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This way our max retry limit holds as well.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
As Dan Carpenter pointed out: mixing 16-bit nvme status with 32-bit
error status from driver. Corrected comment on fcp request struct
status field, and converted done routine to explicitly set nvme status
codes for nvme status.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Clear SG list to avoid double frees of payload page list
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
LS validations shouldn't have been independent checks.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Update FC-NVME definitions to match FC-NVME r1.14 (16-020vB) plus
change voted in by 2/22 FC-NVME Adhoc (see HOSTID below).
Includes the following:
- Addition of "status_code" field to ERSP IU
- Addition of FC-NVME LS RJT reason_codes and reason_explanations
- CreateAssociation payload, HostID field shortened to 16 bytes
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Before scheduling a reconnect attempt, check
nr_reconnects against max_reconnects, if not
exhausted (or max_reconnects is not -1), schedule
a reconnect attempts, otherwise schedule ctrl
removal.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
When a host sense that its controller session is damaged,
it tries to re-establish it periodically (reconnect every
reconnect_delay). It may very well be that the controller
is gone and never coming back, in this case the host will
try to reconnect forever.
Add a ctrl_loss_tmo to bound the number of reconnect attempts
to a specific controller (default to a reasonable 10 minutes).
The timeout configuration is actually translated into number of
reconnect attempts and not a schedule on its own but rather
divided with reconnect_delay. This is useful to prevent
racing flows of remove and reconnect, and it doesn't really
matter if we remove slightly sooner than what the user requested.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
we already have it in opts.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If nvmf_register_transport happened to fail
(it can't, but theoretically) we leak memory.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
if nvmf_register_transport happend to fail, we
need to nvmet_unregister_transport as well.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If nvmf_register_transport happened to fail
(it can't, but theoretically) we leak memory.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch introduces helper function for checking controller
status during admin and io command processing which returns u16
status. As to bring consistency on returning status, other
friend functions also now return u16 status instead of int
to match the spec.
As part of the theseerror log prints in also prints qid on
which command error occured.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Both the destination and the host addresses are now
parsed using inet_pton_with_scope helper. We also
get ipv6 (with address scopes support).
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of parsing address strings, use a generic
helper. This also adds ipv6 (with address scopes)
support.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
Several locations in the stack need to handle ipv4/ipv6
(with scope) and port strings conversion to sockaddr.
Add a helper that takes either AF_INET, AF_INET6 or
AF_UNSPEC (for wildcard) to centralize this handling.
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The target might be occupied with multiple hosts so lets
give it some more grace before failing the connection
establishment.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If we are attacked with establishments/teradowns we need to
make sure we do not consume too much system memory. Thus
let ongoing controller teardowns complete before accepting
new controller establishments.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
If a cpu unplug event has occured, we need to take the minimum
of the provided nr_io_queues and the number of online cpus,
otherwise we won't be able to connect them as blk-mq mapping
won't dispatch to those queues.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
When handling a new recv command, we grab a new rsp resource and
check for the queue state being live. In case the queue is not in
live state, we simply restore the rsp back to the free list. However
in this flow we didn't set rsp->queue yet, so we cannot dereference it.
Instead, make sure to initialize rsp->queue (and other rsp members)
as soon as possible so we won't reference uninitialized variables.
Reported-by: Yi Zhang <yizhan@redhat.com>
Reported-by: Raju Rangoju <rajur@chelsio.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
percpu_ref_kill is not enough to prevent subsequent
percpu_ref_tryget_live from failing. Hence call
perfcpu_ref_kill_confirm to make it safe.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
The incorrect offset was used when trying to read the RXSTCMD register.
Signed-off-by: Markus Marb <markus@marb.org>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The HDMI TX controller support HPD and RXSENSE signaling from the PHY
via it's STAT0 PHY interface, but some vendor PHYs can manage these
signals independently from the controller, thus these STAT0 handling
should be moved to PHY specific operations and become optional.
The existing STAT0 HPD and RXSENSE handling code is refactored into
a supplementaty set of default PHY operations that are used automatically
when the platform glue doesn't provide its own operations.
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491309119-24220-2-git-send-email-narmstrong@baylibre.com